High Molecular Weight Methacrylate Sealing of a Bridge Deck, HR-2031, Construction Report, 1988

The Iowa Department of Transportation used a high molecular weight methacrylate (HMWM) resin to seal a 3,340 ft. x 64 ft. bridge deck in October 1986. The sealing was necessary to prevent deicing salt brine from entering a substantial number of transverse cracks that coincided with the epoxy coated top steel and unprotected bottom steel. HMWM resin is a three component product composed of a monomer, a curnene hydroperoxide initiator and a cobalt naphthenate promoter. The HMWM was applied with a dual spray bar system and flat-fan nozzles. Initiated monomer delivered through one spray bar was mixed in the air with promoted monomer from the other spray bar. The application rate averaged 0.956 gallons per 100 square feet for the tined textured driving lanes. Dry sand was broadcast on the surface at an average coverage of 0.58 lbs. per square yard to maintain friction. Coring showed that the H.MWM resin penetrated the cracks more than two inches deep. Testing of the treated deck yielded Friction Numbers averaging 33 with a treaded tire compared to 36 prior to treatment. An inspection soon after treatment found five leaky cracks in one of the 15 spans. One inspection during a steady rain showed no leakage, but leakage from numerous cracks occurred during a subsequent rain. A second HMWM application was made on two spans to determine if a double application would prevent leakage. This evaluation has not been completed.

A radiochemical method for carbamoyl-phosphate synthetase I: application to rats fed a hyperproteic diet

A method for the measurement of carbamoyl-phosphate synthetase I activity in animal tissues has been developed using the livers of rats under normal and hyperproteic diets. The method is based on the incorporation of 14C-ammonium bicarbonate to carbamoyl-phosphate in the presence of ATP-Mg and N-acetyl-glutamate. The reaction is stopped by chilling, lowering the pH and adding ethanol. Excess bicarbonate is flushed out under a gentle stream of cold CO2. The only label remaining in the medium was that incorporated into carbamoyl-phosphate, since all 14C-CO2 from bicarbonate was eliminated. The method is rapid and requires only a low pressure supply of CO2 to remove the excess substrate. The reaction is linear up to 10 min using homogenate dilutions of 1:20 to 1:200 (w/v). Rat liver activity was in the range of 89±8 nkat/g. Hyperproteic diet resulted in a significant 1.4-fold increase. The design of the method allows for the processing of multiple samples at the same time, and incubation medium manipulation is unnecessary, since the plastic incubation vial and its contents are finally counted together.

New trends in the kitchen: propellants assessment of edible food aerosol sprays used on food.

New products available for food creations include a wide variety of "supposed" food grade aerosol sprays. However, the gas propellants used cannot be considered as safe. The different legislations available did not rule any maximum residue limits, even though these compounds have some limits when used for other food purposes. This study shows a preliminary monitoring of propane, butane and dimethyl ether residues, in cakes and chocolate after spraying, when these gases are used as propellants in food aerosol sprays. Release kinetics of propane, butane and dimethyl ether were measured over one day with sprayed food, left at room temperature or in the fridge after spraying. The alkanes and dimethyl ether analyses were performed by headspace-gas chromatography-mass spectrometry/thermal conductivity detection, using monodeuterated propane and butane generated in situ as internal standards. According to the obtained results and regardingthe extrapolations of the maximum residue limits existing for these substances, different delays should be respected according to the storage conditions and the gas propellant to consume safely the sprayed food.

6.2

Airborne particles can come from a variety of sources and contain variable chemical constituents. Some particles are formed by natural processes, such as volcanoes, erosion, sea spray, and forest fires, while other are formed by anthropogenic processes, such as industrial- and motor vehicle-related combustion, road-related wear, and mining. In general, larger particles (those greater than 2.5 μm) are formed by mechanical processes, while those less than 2.5 μm are formed by combustion processes. The chemical composition of particles is highly influenced by the source: for combustion-related particles, factors such as temperature of combustion, fuel type, and presence of oxygen or other gases can also have a large impact on PM composition. These differences can often be observed at a regional level, such as the greater sulphate-composition of PM in regions that burn coal for electricity production (which contains sulphur) versus regions that do not. Most countries maintain air monitoring networks, and studies based on the resulting data are the most common basis for epidemiology studies on the health effects of PM. Data from these monitoring stations can be used to evaluate the relationship between community-level exposure to ambient particles and health outcomes (i.e., morbidity or mortality from various causes). Respiratory and cardiovascular outcomes are the most commonly assessed, although studies have also considered other related specific outcomes such as diabetes and congenital heart disease. The data on particle characteristics is usually not very detailed and most often includes some combination of PM2.5, PM10, sulphate, and NO2. Other descriptors that are less commonly found include particle number (ultrafine particles), metal components of PM, local traffic intensity, and EC/OC. Measures of association are usually reported per 10 μg/m3 or interquartile range increase in pollutant concentration. As the exposure data are taken from regional monitoring stations, the measurements are not representative of an individual's exposure. Particle size is an important descriptor for understanding where in the human respiratory system the particles will deposit: as a general rule, smaller particles penetrate to deeper regions of the lungs. Initial studies on the health effects of particulate matter focused on mass of the particles, including either all particles (often termed total suspended particulate or TSP) or PM10 (all particles with an aerodynamic diameter less than 10 μm). More recently, studies have considered both PM10 and PM2.5, with the latter corresponding more directly to combustion-related processes. UFPs are a dominant source of particles in terms of PNC, yet are negligible in terms of mass. Very few epidemiology studies have measured the effect of UFPs on health; however, the numbers of studies on this topic are increasing. In addition to size, chemical composition is of importance when understanding the toxicity of particles. Some studies consider the composition of particles in addition to mass; however this is not common, in part due the cost and labour involved in such analyses.

Bud dormancy in apple trees after thermal fluctuations

The objective of this work was to evaluate the effect of heat waves on the evolution of bud dormancy, in apple trees with contrasting chilling requirements. Twigs of 'Castel Gala' and 'Royal Gala' were collected in orchards in Papanduva, state of Santa Catarina, Brazil, and were exposed to constant (3°C) or alternating (3 and 15°C for 12/12 hours) temperature, combined with zero, one or two days a week at 25°C. Two additional treatments were evaluated: constant temperature (3°C), with a heat wave of seven days at 25°C, in the beginning or in the middle of the experimental period. Periodically, part of the twigs was transferred to 25°C for daily budburst evaluation of apical and lateral buds. Endodormancy (dormancy induced by cold) was overcome with less than 330 chilling hours (CH) of constant cold in 'Castel Gala' and less than 618 CH in 'Royal Gala'. A daily 15°C-temperature cycle did not affect the endodormancy process. Heat waves during endodormancy resulted in an increased CH to achieve bud requirements. The negative effect of high temperature depended on the lasting of this condition. Chilling was partly cancelled during dormancy when the heat wave lasted 36 continuous hours or more. Therefore, budburst prediction models need adjustments, mainly for regions with mild and irregular winters, such as those of Southern Brazil.

Quality improvement for portal vein embolization.

Fibrin sealant is used in many areas of surgery. We present a novel aspect of flap insetting in the ischial region using fibrin spray to seal the transferred tissue. We analyzed 10 patients suffering from decubital ulcers and assessed drainage output, time of drain removal, as well as complications following fasciocutaneous flap surgery. Patients were randomized to receive sprayed fibrin glue (study group) or not (control group) before wound closure. The mean drainage time was 4 +/- 1 days in the study group and 6 +/- 1 days in the control group ( P = 0.06). The mean drainage volume was 100 +/- 20 mL in the study group and 168 +/- 30 mL in the control group ( P < 0.01). Fibrin sealant led to reduced drainage volumes and duration of drainage, indicating a beneficial effect of the application of fibrin glue in fasciocutaneous flap surgery for pressure sore coverage.

Modeling of Pressurizer Using APROS and TRACE Thermal Hydraulic Codes

Diplomityön tavoitteena on paineistimen yksityiskohtainen mallintaminen APROS- ja TRACE- termohydrauliikkaohjelmistoja käyttäen. Rakennetut paineistinmallit testattiin vertaamalla laskentatuloksia paineistimen täyttymistä, tyhjentymistä ja ruiskutusta käsittelevistä erilliskokeista saatuun mittausdataan. Tutkimuksen päätavoitteena on APROSin paineistinmallin validoiminen käyttäen vertailuaineistona PACTEL ATWS-koesarjan sopivia paineistinkokeita sekä MIT Pressurizer- ja Neptunus- erilliskokeita. Lisäksi rakennettiin malli Loviisan ydinvoimalaitoksen paineistimesta, jota käytettiin turbiinitrippitransientin simulointiin tarkoituksena selvittää mahdolliset voimalaitoksen ja koelaitteistojen mittakaavaerosta johtuvat vaikutukset APROSin paineistinlaskentaan. Kokeiden simuloinnissa testattiin erilaisia noodituksia ja mallinnusvaihtoehtoja, kuten entalpian ensimmäisen ja toisen kertaluvun diskretisointia, ja APROSin sekä TRACEn antamia tuloksia vertailtiin kattavasti toisiinsa. APROSin paineistinmallin lämmönsiirtokorrelaatioissa havaittiin merkittävä puute ja laskentatuloksiin saatiin huomattava parannus ottamalla käyttöön uusi seinämälauhtumismalli. Työssä tehdyt TRACE-simulaatiot ovat osa United States Nuclear Regulatory Commissionin kansainvälistä CAMP-koodinkehitys-ja validointiohjelmaa.

Contemporary engagements within corridors of the past: temporal elasticity, graffiti, and the materiality of St. Rock Street, Barcelona

In a medieval Barcelonan side-street, urine, rubbish, and a bewildering array of graphic imagery splatters the narrowing walls between two major thoroughfares. A contemporary conflict between residents, unknown artists and others is played out using banners, bottles, stickers, posters, stencils, spray paint, and bodily substances. In this shadowed liminality, local and global debates are superimposed upon substructures constructed from disease, prostitution, and the Saint of the Plague. The continuing urban struggle constitutes temporal statements of dirt and purity, violence and humour, dominance and resistance, death and salvation. Like the renovated facades masking the crumbling remains of structures long neglected, the government’s literal whitewashing of the art is a temporal cover-up of a discursive symptom stretching from deeply embedded preconditions. However, from his niche in the angular bend of the alley bearing his name, the statue of St. Rock remains unblinkingly staring, raised above the contestations expressed below.

Kosteuden ja neliömassan mittaaminen kartonkikoneen viiraosalla

Diplomityön tavoitteena oli selvittää spraytärkkelyksen ja eri kerrosten liitossakeuksien vaikutusta kartongin palstautumislujuuteen ja formaatioon. Työn teon aikana viiraosille hankittiin gammasäteilyllä toimivat kosteusmittarit. Työssä haettiin keinoja varmentaa mit-tausten luotettavuus kartonkikoneella, jonka nopeudet ja tuotteiden neliömassat vaihtelevat suuresti. Työn loppuvaiheessa aloitettiin mittareiden toiminnan parantaminen. Spraytärk-kelyksen annostelua parannettiin ja annostelulle rakennettiin suhdesäätö. Tärkkisumun aiheuttamia haittoja vähennettiin lisäämällä spraytärkkelysputkien yhteyteen tärkkelys-tippoja poistavia imupalkkeja. Tämän diplomityön kirjallisuusosan tavoitteena oli tarkastella taivekartonkia tuotteena ja sen kilpailukyvyn kannalta tärkeitä ominaisuuksia. Kilpailukyvyn kannalta tärkeään palstautumislujuuteen sekä taivutusjäykkyyteen kiinnitettiin huomiota niiden toisistaan riippuvuuksien vuoksi. Spraytärkkelyksen käyttö riittävän palstautumislujuuden varmistajana ja spraytärkkelyksen määrän hallinta olivat kirjallisuusosassa mukana. Liitossakeuksien hallinta gammasäteilyä hyödyntävien NDC-mittareiden avulla oli toinenpääalue. Kirjallisuusosassa on viitattu myös tehtaalta saatuihin kokemusperäisiin tietoihin. Tämän työn kokeellisessa osassa selvitettiin InkeroistenKartonkitehtaan Kartonkikone 4:a. ja sillä suoritettuja spraytärkkelyskokeita. Liitoskosteuksia selvitettiin pääosin aiempien mittausten ja kokemusten perusteella.

Conservação pós-colheita de abacaxi 'Pérola' colhido no estádio de maturação "pintado" associando-se refrigeração e atmosfera modificada

Estudou-se a manutenção da qualidade do abacaxi 'Pérola', utilizando-se de refrigeração e atmosfera modificada. Os frutos foram armazenados em ambiente com controle de temperatura a 8ºC e 90%UR, durante 17 dias, quando foram transferidos para condição de ambiente (25ºC, 75-80%UR). Eles foram avaliados na recepção, caracterizando-os, após 5; 9; 13 e 17 dias sob refrigeração, e depois de transferidos para as condições de ambiente, aos 21; 25 e 29 dias. O delineamento experimental utilizado foi o inteiramente casualizado, em esquema fatorial (6 x 8), tendo-se seis tratamentos (testemunha, duas ceras e três filmes plásticos) e oito épocas de avaliação. Os frutos foram avaliados quanto à coloração, ocorrência de podridões e de escurecimento interno, e a polpa avaliada quanto ao pH e aos teores de sólidos solúveis totais (SST), acidez total titulável (ATT), ácido ascórbico e açúcares solúveis, totais e redutores. Durante o armazenamento, observaram-se o amarelecimento dos frutos, o aumento no pH, na relação SST/ATT, e nos teores de açúcares solúveis, totais e redutores, que foram maiores após a transferência dos frutos para o ambiente. Os sintomas de injúria por chilling aumentaram com o tempo de armazenamento. Os tratamentos que modificam a atmosfera (embalagens e ceras) não influenciam significativamente nos principais atributos de qualidade do abacaxi 'Pérola', mas o uso de embalagem com PEBD e PVC atrasou o aparecimento de sintomas de escurecimento interno após a transferência dos frutos para a condição ambiente. Os frutos sem embalagem e os tratados com cera mostraram-se mais sensíveis à injúria por chilling, que se manifestou aos quatro dias após a remoção para o ambiente. A embalagem em PEBD e PVC retardou o aparecimento dos primeiros sintomas, em quatro dias.

Deposición transversal de líquido de las boquillas de doble abanico TTJ60-11004 y TTJ60-11002 en distintas condiciones operacionales

El objetivo de este trabajo fue el de evaluar la deposición transversal de caldo de las boquillas pulverizadoras de doble abanico TTJ60-11004 y TTJ60-11002 en distintas condiciones operacionales. Se utilizaron 5 muestras de cada boquilla pulverizadora siendo considerada cada unidad, una repetición. La distribución de caldo fue evaluada por medio de una mesa de evaluación de distribución construida de acuerdo con la norma ISO 56821. Se evaluó el perfil de distribución individual, la distribución volumétrica simulada de la superposición de los chorros por medio del coeficiente de variación (CV%) de los volúmenes colectados, el caudal y el ángulo de abertura de los chorros. Las condiciones operacionales fueron: presión de trabajo de 200, 300 y 400 Kpa, altura de 30, 40 y 50 cm en relación al blanco y espaciamiento entre boquillas simulados en Software (Microsoft Excel) entre 45 y 100 cm. Las boquillas presentaron perfil individual descontinuo con la mayor deposición de líquido en la región central y reducción del volumen gradual en dirección a las extremidades. El aumento de la presión promovió alargamiento del perfil y de la franja de aplicación. Las boquillas proporcionaron perfil uniforme que dependió del espaciamiento entre las boquillas, con valores menores con reducción en el espaciamiento y en presiones mayores. El caudal y el ángulo del chorro aumentaron con el incremento en la presión.

Distribuição de líquido da ponta de pulverização com indução de ar e jato excêntrico AIUB 8502 sob diferentes condições

Objetivou-se com este trabalho avaliar a distribuição de líquido da ponta de pulverização com indução de ar e jato excêntrico AIUB 8502 sob diferentes condições operacionais. Foram avaliados perfil individual, vazão, ângulo de abertura do jato, faixa de aplicação e distribuição volumétrica simulada de duas pontas AIUB 8502 nas pressões de trabalho de 200, 300, 400 e 500 kPa, altura de 30, 40 e 50 cm em relação ao alvo e espaçamento entre pontas de 30 a 100 cm. Todas as análises foram realizadas seguindo a norma ISSO 5682-1, com algumas adaptações. A ponta apresentou distribuição de líquido excêntrica com um lado descontínuo e extremidade oposta excêntrica, com queda abrupta do volume de líquido. À medida que se aumentou a altura da barra e a pressão de trabalho, alongou-se o perfil do jato. O maior número de configurações uniformes foi obtido na altura de 50 cm, decrescendo nas alturas de 40 e 30 cm. A vazão e o ângulo do jato excêntrico aumentaram com o incremento na pressão, não havendo diferença entre o ângulo do jato descontínuo e o total entre as pressões de 400 e 500 kPa e de 200 e 300 kPa.

Distribuição volumétrica e espectro de gotas de pontas de pulverização de baixa deriva

Objetivou-se neste trabalho avaliar a distribuição volumétrica e o espectro de gotas das pontas de pulverização de baixa deriva TTI110015, AI110015 e AVI11001 sob diferentes condições operacionais. A distribuição volumétrica foi determinada em bancada de ensaios padronizada analisando o coeficiente de variação (CV%) de uma barra simulada em computador, utilizando pressões de 200, 300 e 400 kPa, altura de 30, 40 e 50 cm em relação à bancada e espaçamento entre pontas de 40 a 100 cm. O espectro de gotas foi produzido utilizando-se apenas água como calda em um analisador de partículas em meio aquoso, nas pressões de 200, 300 e 400 kPa. Foram avaliados o DMV, a porcentagem de gotas com diâmetro inferior a 100 µm (%100 µm) e a amplitude relativa (AR). As pontas proporcionaram perfil descontínuo nas pressões de 300 e 400 kPa e uniforme a 200 kPa. Na pressão de 200 kPa, as pontas foram adequadas apenas para aplicação em faixa, e a 300 e 400 kPa, apenas para área total. Ocorreu menor CV (abaixo de 7%) com a maior pressão de trabalho e menor espaçamento entre pontas. À medida que se aumentou a pressão de trabalho, reduziu-se o DMV. As pontas TTI110015 e AI110015 em todas as pressões e a ponta AVI11001 na pressão de 200 kPa produziram gotas extremamente grossas e gotas grossas nas pressões de 300 e 400 kPa apenas para a ponta AVI11001. As pontas proporcionaram baixos valores de amplitude relativa (AR) e gotas de tamanho uniforme, bem como produziram baixa porcentagem de gotas menores que 100 µm, principalmente TTI110015 e AI110015, com menor risco de deriva.

The impact of breeding on fruit production in warm climates of Brazil

Brazil is a very large country with a diverse climate. This fact allows a diversity of plants to grow ranging from tropical rainforest in the Amazon, passing through Atlantic Forest along the coast, the cerrados (Brazilian savannah) in the Central West region, and semi-arid area in the Northeast. Latitude ranges from 5º N to 33º S, with most of this territory in the tropical region. There are enough reasons to plant breeders devoting great amount of their effort to improve plants suitable for warm climates, though. Among fruit crops, results of breeder's work have been noticed in several species, especially on peaches, grapes, citrus, apples, persimmons, figs, pears and others not so common, such as acerola, guava, annonas (sour sop, sugar apple, atemoya, cherimoya) and passion fruit. Peach tree introduced at low latitude (22 ± 2ºS) requires climatic adaptation to subtropical conditions of low chilling. In Brazil, the first peach breeding program aiming adaptation of cultivars to different habitats was developed by Instituto Agronômico de Campinas (IAC) beginning in the end of the 40's. Apple low chill requirement cultivars obtained in a South state, Paraná, are now been planted at low latitudes. Banana and pineapple breeding programs from Embrapa units along the country are successfully facing new sanitary problems. Petrolina/Juazeiro, in the Northeastern region (9ºS), is the main grape exporting region with more than 6,000 ha. Grape growing in the region is based in the so called "tropical" rootstocks released by IAC, namely: IAC 313 'Tropical', IAC 572 'Jales'. Recently, Embrapa Grape and Wine released tropical grape seedless cultivars that are changing table grape scenario in the country.

Sensory characteristics of 'Douradão' peaches submitted to modified atmosphere packaging

The sensory, physical and chemical characteristics of 'Douradão' peaches cold stored in different modified atmosphere packaging (LDPE bags of 30, 50, 60, 75µm thickness) were studied. After 14, 21 and 28 days of cold storage (1 ± 1 ºC and 90 ± 5% RH), samples were withdrawn from MAP and kept during 4 days in ambient air for ripening. Descriptive terminology and sensory profile of the peaches were developed by methodology based on the Quantitative Descriptive Analysis (QDA). The assessors consensually defined the sensory descriptors, their respective reference materials and the descriptive evaluation ballot. Fourteen individuals were selected as judges based on their discrimination capacity and reproducibility. Seven descriptors were generated showing similarities and differences among the samples. The data were analysed by ANOVA, Tukey test and Principal Component Analysis (PCA). The atmospheres that developed inside the different packaging materials during cold storage differed significantly. The PCA showed that MA50 and MA60 treatments were more characterized by the fresh peach flavour, fresh appearance, juiciness and flesh firmness, and were effective for keeping good quality of 'Douradão' peaches during 28 d of cold storage. The Control and MA30 treatments were characterized by the mealiness, the MA75 treatment showed lower intensity for all attributes evaluated and they were ineffective to maintain good quality of the fruits during cold storage. Higher correlation coefficients (positive) were found between fresh appearance and flesh firmness (0.95), fresh appearance and juiciness (0.97), ratio and intensity of fresh peach smell (0.81), as well as higher correlation coefficients (negative) between Hue angle and intensity of yellow colour (-0.91), fresh appearance and mealiness (-0.92), juiciness and mealiness (-0.95), firmness and mealiness (-0.94).