Structure, mobility and clustering of interstitial O in La2CuO4+delta in the limit of small delta

Anelastic spectra (elastic energy absorption as a function of temperature) are reported which provide evidence that excess O in La2CuO4+delta starts forming two different types of defects already at very low concentrations, where no phase separation or changes in the type of O intercalation are believed to occur. The absorption peak with the lowest activation enthalpy, H/k(B) = 5600 K, is visible at lowest values of delta and is attributed to the hopping of single interstitial O2- ions. The second process, with a slightly slower dynamics, appears at higher values of delta and soon becomes preponderant over the former process. The latter process is proposed to be due to stable pairs of O atoms and is put in connection with the formation of partially covalent bonds between interstitial and apical oxygen; such bonds would reduce the doping efficiency of excess O at increasing delta. The geometry of the interstitial O defect is discussed. O 1998 Published by Elsevier B.V. B.V. All rights reserved.

A nonisothermal study of the kinetics of the nanoporosity elimination in sonogels-derived silica xerogels

A nonisothermal study of the kinetics of the nanoporosity elimination in monolithic silica xerogels, prepared from acid and ultrasound catalyzed hydrolysis of tetraethylortosilicate (TEOS), has been carried out by means of in situ linear shrinkage measurements performed with different heating rates. The study could be applied up to almost alpha similar to 0.6 of the volume fraction alpha of eliminated pores. The activation energy was found increasing from about 3.2 x 10(2) kJ/mol for alpha similar to 0.06 up to about 4.4 x 10(2) kJ/mol for alpha. similar to 0.44. The sintering process accompanying the nanopore elimination in this set of xerogels is in agreement with a viscous flux sintering process with the hydroxyl content diminishing with the volume fraction of eliminated pores. All the volume fraction of eliminated pores versus temperature (T) curves can be matched onto a unique curve with an appropriate rescaling of the T axis, independent of the heating rate. This scaling property suggests that the path of sintering seems the same, regardless of the heating rate; the difference is that the rate is faster at higher temperature.

Clavulanic acid production by immobilized cells if Streptomyces clavuligerus

A clavulanic acid production process with immobilized Streptomyces clavuligerus cells was investigated. Cells were immobilized in diatomaceous earth, calcium alginate gel as well as in the form of natural pellets and cultivated in shake flasks in a medium containing glycerol and soytone as the carbon and nitrogen sources, respectively. In all experiments growth occurred in the first 48 h and glycerol consumption after 72 h, while clavulanic acid production was observed between 48 and 60h, with gradual degradation after this period. The natural pellets presented higher product concentration as compared with the cells immobilized in supports. However, calcium alginate was found to be the best support in relation to cell retention capacity.

Evaluation of dental pulp repair using low level laser therapy (688 nm and 785 nm) morphologic study in capuchin monkeys

The aim of this study was to evaluate the hypothesis that low-level laser therapy (LLLT) 688 nm and 785 nm accelerate dentin barrier formation and repair process after traumatic pulp exposure. The sample consisted of 45 premolars of capuchin monkeys (Cebus apella) with pulp exposure Class V cavities. All premolars were treated with calcium hydroxide (Ca(OH)(2)), divided in groups of 15 teeth each, and analyzed on 7(th), 25(th), and 60(th) day. Group GI - only Ca(OH)(2), GIF- laser 688 nm, and GIII - laser 785 nm. Laser beam was used in single and punctual dose with the parameters: continuous, 688 nm and 785 nm wavelength, tip's area of 0.00785 cm(2), power 50 mW, application time 20 s, dose 255 J/cm(2), energy 2 J. Teeth were capped with Ca(OH)(2), Ca(OH)(2) cement and restored with amalgam. All groups presented pulp repair. on 25(th) day the thickness of the formed dentin barrier was different between the groups GI and GII (p < 0.05) and between groups GI and GIII (p < 0.01). on 60(th) day there was difference between GI and GIII (p < 0.01). It may be concluded that, LLLT 688 nm and 785 nm accelerated dentin barrier formation and consequently pulp repair process, with best results using infrared laser 785 nm. (c) 2009 by Astro Ltd. Published exclusively by WLLEY-VCH Verlag GmbH & Co. KGaA

Effects of dispersion by Gd3+ upon europium diphenylphosphinate luminescence

A series of binary diphenylphosphinates with Eu3+ and Gd3+ were prepared. The compounds have the general formula Gd1-xEux(DPP)(3), where x ranges from 0 to 1. The spectroscopic measurements show interesting behavior. The intensity of the D-5(0) --> F-7(2) transitions decreases relative to D-5(0) --> F-7(1) With an increase in europium dispersion. Inside the temporal domain, the same decrease is observed with increasing delay after excitation. The lifetimes are also affected, which can be seen in the x = 1 compound, where the decay is a first-order process and lifetime values are 4.81 ms. In the binary compound, as an effect of dispersion, the lifetime of the D-5(0) level measured at the D-5(0) --> F-7(1) transition increases with europium dispersion, and the average along the series is 6.25 ms. The decay measured at the D-5(0) --> F-7(2) transitions reveals a second-order process with lifetimes ranging from 1.90 to 6.00 ms. (C) 2001 Elsevier B.V. B.V. All rights reserved.

Chlorine dioxide against bacteria and yeasts from the alcoholic fermentation

The ethanol production in Brazil is carried out by fed-batch or continuous process with cell recycle, in such way that bacterial contaminants are also recycled and may be troublesome due to the substrate competition. Addition of sulphuric acid when inoculum cells are washed can control the bacterial growth or alternatively biocides are used. This work aimed to verify the effect of chlorine dioxide, a well-known biocide for bacterial decontamination of water and equipments, against contaminant bacteria ( Bacillus subtilis, Lactobacillus plantarum, Lactobacillus fermentum and Leuconostoc mesenteroides) from alcoholic fermentation, through the method of minimum inhibitory concentration ( MIC), as well as its effect on the industrial yeast inoculum. Lower MIC was found for B. subtilis ( 10 ppm) and Leuconostoc mesenteroides ( 50 ppm) than for Lactobacillus fermentum ( 75 ppm) and Lactobacillus plantarum ( 125 ppm). Additionally, these concentrations of chlorine dioxide had similar effects on bacteria as 3 ppm of Kamoran (R) ( recommended dosage for fermentation tanks), exception for B. subtilis, which could not be controlled at this Kamoran (R) dosage. The growth of industrial yeasts was affected when the concentration of chlorine dioxide was higher than 50 ppm, but the effect was slightly dependent on the type of yeast strain. Smooth yeast colonies ( dispersed cells) seemed to be more sensitive than wrinkled yeast colonies ( clustered cells/pseudohyphal growth), both isolated from an alcohol-producing unit during the 2006/2007 sugar cane harvest. The main advantage in the usage of chlorine dioxide that it can replace antibiotics, avoiding the selection of resistant populations of microorganisms.

Congenic strains reveal the effect of the renin gene on skeletal muscle angiogenesis induced by electrical stimulation

Previous studies have indicated the importance of angiotensin II (ANG II) in skeletal muscle angiogenesis. The present study explored the effect of regulation of the renin gene on angiogenesis induced by electrical stimulation with the use of physiological, pharmacological, and genetic manipulations of the renin-angiotensin system (RAS). Transfer of the entire chromosome 13, containing the physiologically regulated renin gene, from the normotensive inbred Brown Norway (BN) rat into the background of an inbred substrain of the Dahl salt-sensitive (SS/Mcwi) rat restored renin levels and the angiogenic response after electrical stimulation. This restored response was significantly attenuated when SS-13BN/Mcwi consomic rats were treated with lisinopril or high-salt diet. The role of ANG II on this effect was confirmed by the complete restoration of skeletal muscle angiogenesis in SS/Mcwi rats infused with subpressor doses of ANG II. Congenic strains derived from the SS-13BN/Mcwi consomic were used to further verify the role of the renin gene in this response. Microvessel density was markedly increased after stimulation in congenic strains that contained the renin gene from the BN rat (congenic lines A and D). This angiogenic response was suppressed in control strains that carried regions of the BN genome just above (congenic line C) or just below (congenic line B) the renin gene. The present study emphasizes the importance of maintaining normal renin regulation as well as ANG II levels during the angiogenesis process with a combination of physiological, genetic, and pharmacological manipulation of the RAS.

Impedance spectroscopy study of dehydrated chitosan and chitosan containing LiClO4

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The dielectric suppress and the control of semiconductor non-Ohmic feature of CaCu3Ti4O12 by means of tin doping

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Contribution of the study of the styloid prominence in the posterior tympanic cavity

70 human temporal bones were analyzed with the aid of an otologic microscope. The styloid prominence was found to be extremely variable in shape, location and occurrence. Depending on the degree of development, the prominence establishes important relationships with the sinus tympani, with the fossula of the cochlear fenestra, and with the suprapyramidal recess. Serial sections were used to study the relationship of the styloid process with the facial nerve inside the bony mass of the mastoid portion of the temporal bone.

Análise do comportamento de rebolos convencionais na retificação de aços frágeis e dúcteis

The aim of this work war to study the behavior of the plan tangential grinding process with conventional grinding wheels, under several machining conditions and a selected dressing condition. The analysis of the grinding performance was done regarding the cutting surface wear behavior of the grinding wheel for brittle and ductile steels workpieces. The grinding input parameters, which were, cutting speed, workpiece speed and cutting feed, were chosen based on the grinding machine characteristics. The results discussion emphasized the wear mechanism of the grinding wheel cutting surface and the cutting phenomenology of the grinding process.

Advanced ceramics: Evaluation of the mechanism of stock removal and ground surface quality

The aim of this work is to evaluate the mechanism of stock removal and the ground surface quality of advanced ceramics grounded by a plane tangential grinding process with diamond grinding wheels. The analysis of the grinding performance was done regarding the cutting surface wear behavior of the grinding wheel for ceramic workpieces. The discussion about the results emphasized the wear mechanism of the grinding wheel cutting surface and the cutting phenomenology of the grinding process. The grounded surface was evaluated using Scanning Electron Microscopy (SEM). © 1999 Society of Automotive Engineers, Inc.

Direct amorphous-to-cubic perovskite phase transformation for lead titanate

The phase evolution of lead titanate processed by the polymeric precursor method was investigated by thermal analysis, X-ray diffraction, and high-resolution transmission electron microscopy. The results showed that the cubic perovskite PbTiO3 (PT) phase is formed from an inorganic amorphous precursor at a temperature of 444 °C. A gradual transition from cubic to tetragonal perovskite PT was observed with the increase of calcination time at this temperature. HRTEM results showed that the cubic PT particles have a size of around 5 nm. The identification of cubic PT as an intermediate phase supports the hypothesis that the chemical homogeneity was kept at the molecular level during the synthesis process, with no cation segregation.

Rectificacion de aceros fragiles y ductiles: Parametros de entrada para obtener los mejores resultados

In this work, the behavior of the steel surface grinding process with conventional grinding wheels was studied for various grinding conditions and a fixed dressing condition. The input parameters (wheel speed, workpiece speed, depth of cut), that set up the grinding conditions were determined as a function of the characteristics of the grinding machine. A test bench was established where the grinding power was measured in real time as a function of the volume of material removed. The results showed that in the grinding of fragile steels with a soft wheel and medium grit size, the average power of the cut shows a tendency to increase and become stabilized. The surface roughness of the piece decreased in all the tests and was proportional to the increase in the number of active grits. In tests on the grinding of ductile steels with a soft wheel and fine grit size, the wheel became dull until the moment that the abrasive grits were released from the cut surface.

Gg → h → τ+τ- at the upgraded Fermilab Tevatron

We study the neutral Higgs boson production via the gluon fusion process with the τ+τ- final state at the upgraded Fermilab Tevatron, including a complete simulation of signal channels and leading background processes. For the SM Higgs boson, this h → τ +τ- channel may provide important addition for the Higgs boson discovery in the mass range 120 -140 GeV. In minimal supersymmetric models, natural enhancement for the signal rate over the SM expectation makes the h, H, A → τ+τ- signal observable for large tan β and low MA, which may lead to full coverage for SUSY Higgs parameters at the Tevatron with a moderate integrated luminosity. © SISSA/ISAS 2003.