948 resultados para STABILIZED CDTE NANOCRYSTALS
Resumo:
Hydrogenated nanocrystalline silicon thin-films were obtained by catalytic chemical vapour deposition at low substrate temperatures (150°C) and high deposition rates (10 Å/s). These films, with crystalline fractions over 90%, were incorporated as the active layers of bottom-gate thin-film transistors. The initial field-effect mobilities of these devices were over 0.5 cm 2/V s and the threshold voltages lower than 4 V. In this work, we report on the enhanced stability of these devices under prolonged times of gate bias stress compared to amorphous silicon thin-film transistors. Hence, they are promising candidates to be considered in the future for applications such as flat-panel displays.
Resumo:
The very usual columnar growth of nanocrystalline silicon leads to electronic transport anisotropies. Whereas electrical measurements with coplanar electrodes only provide information about the electronic transport parallel to the substrate, it is the transverse transport which determines the collection efficiency in thin film solar cells. Hence, Schottky diodes on transparent electrodes were obtained by hot-wire CVD in order to perform external quantum efficiency and surface photovoltage studies in sandwich configuration. These measurements allowed to calculate a transverse collection length, which must correlate with the photovoltaic performance of thin film solar cells. Furthermore, the density of charge trapped at localized states in the bandgap was estimated from the voltage dependence of the depletion capacitance of these rectifying contacts.
Resumo:
The charge ordered La1/3Sr2/3FeO3−δ (LSFO) in bulk and nanocrystalline forms are investigated using ac and dc magnetization, M¨ossbauer, and polarized neutron studies. A complex scenario of short-range charge and magnetic ordering is realized from the polarized neutron studies in nanocrystalline specimen. This short-range ordering does not involve any change in spin state and modification in the charge disproportion between Fe3+ and Fe5+ compared to bulk counterpart as evident in the M¨ossbauer results. The refinement of magnetic diffraction peaks provides magnetic moments of Fe3+ and Fe5+ are about 3.15 μB and 1.57 μB for bulk, and 2.7 μB and 0.53 μB for nanocrystalline specimen, respectively. The destabilization of charge ordering leads to magnetic phase separation, giving rise to the robust exchange bias (EB) effect. Strikingly, EB field at 5 K attains a value as high as 4.4 kOe for average size ∼70 nm, which is zero for the bulk counterpart. A strong frequency dependence of ac susceptibility reveals cluster-glass-like transition around ∼65 K, below which EB appears. Overall results propose that finite-size effect directs the complex glassy magnetic behavior driven by unconventional short-range charge and magnetic ordering, and magnetic phase separation appears in nanocrystalline LSFO.
Resumo:
The chicken acid-sensing ion channel ASIC1 has been crystallized as a homotrimer. We address here the oligomeric state of the functional ASIC1 in situ at the cell surface. The oligomeric states of functional ASIC1a and mutants with additional cysteines introduced in the extracellular pore vestibule were resolved on SDS-PAGE. The functional ASIC1 complexes were stabilized at the cell surface of Xenopus laevis oocytes or CHO cells either using the sulfhydryl crosslinker BMOE, or sodium tetrathionate (NaTT). Under these different crosslinking conditions ASIC1a migrates as four distinct oligomeric states that correspond by mass to multiples of a single ASIC1a subunit. The relative importance of each of the four ASIC1a oligomers was critically dependent on the availability of cysteines in the transmembrane domain for crosslinking, consistent with the presence of ASIC1a homo-oligomers. The expression of ASIC1a monomers, trimeric or tetrameric concatemeric cDNA constructs resulted in functional channels. The resulting ASIC1a complexes are resolved as a predominant tetramer over the other oligomeric forms, after stabilization with BMOE or NaTT and SDS-PAGE/western blot analysis. Our data identify a major ASIC1a homotetramer at the surface membrane of the cell expressing functional ASIC1a channel.
Resumo:
Hydrogenated nanocrystalline silicon (nc-Si:H) obtained by hot-wire chemical vapour deposition (HWCVD) at low substrate temperature (150 °C) has been incorporated as the active layer in bottom-gate thin-film transistors (TFTs). These devices were electrically characterised by measuring in vacuum the output and transfer characteristics for different temperatures. The field-effect mobility showed a thermally activated behaviour which could be attributed to carrier trapping at the band tails, as in hydrogenated amorphous silicon (a-Si:H), and potential barriers for the electronic transport. Trapped charge at the interfaces of the columns, which are typical in nc-Si:H, would account for these barriers. By using the Levinson technique, the quality of the material at the column boundaries could be studied. Finally, these results were interpreted according to the particular microstructure of nc-Si:H.
Resumo:
The aim of the present study was to develop novel daptomycin-loaded poly-epsilon-caprolactone (PCL) microparticles with enhanced antibiofilm activity against mature biofilms of clinically relevant bacteria, methicillin-resistant Staphylococcus aureus (MRSA) and polysaccharide intercellular adhesin-positive Staphylococcus epidermidis. Daptomycin was encapsulated into PCL microparticles by a double emulsion-solvent evaporation method. For comparison purposes, formulations containing vancomycin were also prepared. Particle morphology, size distribution, encapsulation efficiency, surface charge, thermal behavior, and in vitro release were assessed. All formulations exhibited a spherical morphology, micrometer size, and negative surface charge. From a very early time stage, the released concentrations of daptomycin and vancomycin were higher than the minimal inhibitory concentration and continued so up to 72 hours. Daptomycin presented a sustained release profile with increasing concentrations of the drug being released up to 72 hours, whereas the release of vancomycin stabilized at 24 hours. The antibacterial activity of the microparticles was assessed by isothermal microcalorimetry against planktonic and sessile MRSA and S. epidermidis. Regarding planktonic bacteria, daptomycin-loaded PCL microparticles presented the highest antibacterial activity against both strains. Isothermal microcalorimetry also revealed that lower concentrations of daptomycin-loaded microparticles were required to completely inhibit the recovery of mature MRSA and S. epidermidis biofilms. Further characterization of the effect of daptomycin-loaded PCL microparticles on mature biofilms was performed by fluorescence in situ hybridization. Fluorescence in situ hybridization showed an important reduction in MRSA biofilm, whereas S. epidermidis biofilms, although inhibited, were not eradicated. In addition, an important attachment of the microparticles to MRSA and S. epidermidis biofilms was observed. Finally, all formulations proved to be biocompatible with both ISO compliant L929 fibroblasts and human MG63 osteoblast-like cells.
Resumo:
BACKGROUND: In published case reports, tocilizumab (TCZ) has shown good efficacy for AA amyloidosis in almost all patients. We investigated the efficacy and safety of TCZ in AA amyloidosis in a multicentre study of unselected cases. METHODS: We e-mailed rheumatology and internal medicine departments in France, Switzerland and North Africa by using the Club Rhumatismes Inflammation (CRI) network and the French TCZ registry, Registry RoAcTEmra (REGATE), to gather data on consecutive patients with histologically proven AA amyloidosis who had received at least one TCZ infusion. Efficacy was defined as a sustained decrease in proteinuria level and/or stable or improved glomerular filtration rate (GFR) and by TCZ maintenance. RESULTS: We collected 12 cases of AA amyloidosis treated with TCZ as monotherapy (mean age of patients 63 ± 16.2 years, amyloidosis duration 20.6 ± 31.3 months): eight patients had rheumatoid arthritis (RA), six with previous failure of anti-tumor necrosis factor α (anti-TNF-α) therapy. In total, 11 patients had renal involvement, with two already on hemodialysis (not included in the renal efficacy assessment). For the nine other patients, baseline GFR and proteinuria level were 53.6 ± 32.8 mL/min and 5 ± 3.3 g/24 h, respectively. The mean follow-up was 13.1 ± 11 months. TCZ was effective for six of the eight RA patients (87.5%) according to European League Against Rheumatism response criteria (four good and two moderate responders). As expected, C-reactive protein (CRP) level decreased with treatment for 11 patients. Renal amyloidosis (n = 9) progressed in three patients and was stabilized in three. Overall, three patients showed improvement, with sustained decrease in proteinuria level (42%, 82% and 96%). Baseline CRP level was higher in subsequent responders to TCZ than other patients (p = 0.02). Among the six RA patients with previous anti-TNF-α therapy, amyloidosis was ameliorated in one and stabilized in three. Three serious adverse events occurred (two diverticulitis and one major calciphylaxia due to renal failure). Finally, 7 of 12 (58%) patients continued TCZ. CONCLUSIONS: The efficacy of TCZ for AA amyloidosis varies depending on the inflammatory status at treatment onset. Discrepancies between our study of unselected consecutive patients and reported cases may be due to publication bias. These results support further prospective trials of TCZ for AA amyloidosis.
Microdoping compensation of microcrystalline silicon obtained by Hot-Wire Chemical Vapour Deposition
Resumo:
Undoped hydrogenated microcrystalline silicon was obtained by hot-wire chemical vapour deposition at different silane-to-hydrogen ratios and low temperature (<300 °C). As well as technological aspects of the deposition process, we report structural, optical and electrical characterizations of the samples that were used as the active layer for preliminary p-i-n solar cells. Raman spectroscopy indicates that changing the hydrogen dilution can vary the crystalline fraction. From electrical measurements an unwanted n-type character is deduced for this undoped material. This effect could be due to a contaminant, probably oxygen, which is also observed in capacitance-voltage measurements on Schottky structures. The negative effect of contaminants on the device was dramatic and a compensated p-i-n structure was also deposited to enhance the cell performance.
Resumo:
The role of bacterial Hsp40, DnaJ, is to co-chaperone the binding of misfolded or alternatively folded proteins to bacterial Hsp70, DnaK, which is an ATP-fuelled unfolding chaperone. In addition to its DnaK targeting activity, DnaJ has a weak thiol-reductase activity. In between the substrate-binding domain and the J-domain anchor to DnaK, DnaJ has a unique domain with four conserved CXXC motives that bind two Zn(2+) and partly contribute to polypeptide binding. Here, we deleted in DnaJ this Zn-binding domain, which is characteristic to type I but not of type II or III J-proteins. This caused a loss of the thiol-reductase activity and strongly reduced the ability of DnaJ to mediate the ATP- and DnaK-dependent unfolding/refolding of mildly oxidized misfolded polypeptides, an inhibition that was alleviated in the presence of thioredoxin or DTT. We suggest that in addition to their general ability to target misfolded polypeptide substrates to the Hsp70/Hsp110 chaperone machinery, Type I J-proteins carry an ancillary protein dithiol-isomerase function that can synergize the unfolding action of the chaperone, in the particular case of substrates that are further stabilized by non-native disulfide bonds. Whereas the unfoldase can remain ineffective without the transient untying of disulfide bonds by the foldase, the foldase can remain ineffective without the transient ATP-fuelled unfolding of wrong local structures by the unfoldase.
Resumo:
BACKGROUND: Switzerland is a region in which alveolar echinococcosis (AE) is endemic. Studies evaluating outcomes after liver resection (LR) for AE are scarce. The aim of this study was to assess the short- and long-term outcomes of AE patients after LR in a single tertiary referral center. METHODS: We retrospectively analyzed data pertaining to all patients with liver AE who were treated with LR at our institution between January 1992 and December 2013. Patient demographics, intraoperative data, extent of LR procedures (major vs. minor LR), postoperative outcomes, and negative histological margin (R0) resection rate were recorded in a database. Recurrence rates after LR were analyzed. RESULTS: LR was performed in 59 patients diagnosed with hepatic AE (56 complete surgeries, 3 reduction surgeries). Postoperative morbidity and mortality were observed in 34 % (25 % grade I-II, 9 % grade III-IV) and 2 % of the patients, respectively. R0 (complete) resection rate was 71 % (n = 42), and R1/R2 resection rate was 29 % (n = 17). Extra-hepatic recurrence occurred in 1 case (lung) after R0 resection. In cases of R1/R2 resection, 7 intra-hepatic disease progressions occurred with a median time of 10 months (IQR 6-11 months). Long-term (more than 1 year) benzimidazole treatment stabilized the disease in 64 % (9/14) of patients with R1 status. The overall survival rate was 97 %. CONCLUSIONS: Liver AE can be safely and definitively treated with LR, provided that R0 resection is achieved. In cases of R1 resection, benzimidazole therapy seems to be effective in stabilizing the intra-hepatic disease and preventing extra-hepatic recurrence.
Resumo:
GdBaCo2O5+x (GBCO) was evaluated as a cathode for intermediate-temperature solid oxide fuel cells. A porous layer of GBCO was deposited on an anode-supported fuel cell consisting of a 15m thick electrolyte of yttria-stabilized zirconia (YSZ) prepared by dense screen-printing anda Ni–YSZ cermet as an anode (Ni–YSZ/YSZ/GBCO). Values of power density of 150 mW cm−2 at 700◦C and ca. 250 mW cm−2 at 800◦C are reported for this standard configuration using 5% of H2 in nitrogen as fuel. An intermediate porous layer of YSZ was introduced between the electrolyte and the cathode improving the performance of the cell. Values for power density of 300 mW cm−2 at 700◦C and ca. 500 mW cm−2 at 800◦C in this configuration were achieved.
Resumo:
El objetivo del presente trabajo es evaluar las propiedades mecánicas, así como los diferentes mecanismos de fractura activados mediante ensayos de indentación instrumentada, de electrolitos basados en circona estabilizada con itria ("yttria stabilized zirconia",YSZ) y ceria dopada con gadolinia ("gadolinia doped ceria", GDC), para pilas de combustible de óxido sólido, SOFCs. Ambos materiales, con un espesor final de 200 ¿m, se conformaron mediante prensado uniaxial a 500 MPa y se sinterizaron a 1400ºC. Propiedades mecánicas tales como la dureza (H) y el módulo de Young (E) han sido estudiadas a diferentes profundidades de penetración utilizando el algoritmo de Oliver y Pharr.
Resumo:
We report on a field-effect light emitting device based on silicon nanocrystals in silicon oxide deposited by plasma-enhanced chemical vapor deposition. The device shows high power efficiency and long lifetime. The power efficiency is enhanced up to 0.1 %25 by the presence of a silicon nitride control layer. The leakage current reduction induced by this nitride buffer effectively increases the power efficiency two orders of magnitude with regard to similarly processed devices with solely oxide. In addition, the nitride cools down the electrons that reach the polycrystalline silicon gate lowering the formation of defects, which significantly reduces the device degradation.
Resumo:
Certain biopolymers are capable of forming physically cross-linked gels in aqueous medium, stabilized by forces such as Coulombic, charge transfer, hydrogen bonding, dipole-dipole, van der Waals, and hydrophobic interactions. The mathematical description of these physical networks are difficult, but should contribute to a better understanding of the gelling process. The Clark and Ross-Murphy model was applied to experimental data for agarose-guar gum mixed systems, in which only agarose is the gelling polysaccharide. A computational routine based on the statistical maximum likehood principle was employed to estimate the f, K and a characteristic parameters. Statistical t-test and F-test were used to analyse the set of parameters.
Resumo:
Data about breeding populations of birds in the Antarctica are rare and fragmented. Thus, information about the status of the breeding populations of Antarctic birds is crucial given the current scenario of climate change, which is particularly acute in Antarctica. This paper presents new information about the populations of the Antarctic tern Sterna vittata, the kelp gull Larus dominicanus, the southern giant petrel Macronectes giganteus, the Antarctic skua Catharacta antarctica lonnbergi, the chinstrap penguin Pygoscelis antarctica and the gentoo penguin Pygoscelis papua on Byers Peninsula (Livingston Island, South Shetland Islands). We used line transects counts to estimate both densities and numbers of nests of the different species. We estimate that there are 398.96 birds km-2 of southern giant petrels (2793 individuals), 62.4 birds km-2 of Antarctic tern (3746 individuals) and 269.1 birds km-2 of kelp gull (1884 individuals). Furthermore, we found 15 nests of Antarctic skua in 25 km2, from which we can estimate that 6091 birds must breed on Byers Peninsula. We also censused two colonies of gentoo penguins (3000 and 1200 pairs) and 50 pairs of chinstrap. Compared to previous estimates, gentoo penguins seem to have increased whereas chinstrap penguin have decreased. Finally, the populations of Antarctic tern, southern giant petrel and kelp gull have stabilized or slightly increased.