HDPE-Ash Nanocomposites

Ash-based polymer composites are assuming increasing importance because of the pollutant potential, fine particle size, and low price of ash. Fly ash and rice husk ash are two prominent ash materials on which some investigations have already been done for potential use in polymer composites. This article highlights the results of a study on the use of wood ash in HDPE. Wood ash is mainly a mixture of various metallic compounds and some silica. Here, the characterization of wood ash has been done with the help of XRD, ICPAES, light scattering based particle size analysis, FTIR, and SEM. The results show that wood ash particle size has an average value of 293 nm, much lower than other categories of ash. When blended with HDPE in the presence of a compatibilizer, wood ash gives rise to vastly improved mechanical properties over that of the base polymer. The results prove that wood ash is a valuable reinforcing material for HDPE and the environmental pollution due to wood ash can be solved in a most profitable way by this technique.

Optimization in the Technological Steps for the Fabrication of Large Area Micromirror Arrays

Micromirror arrays are a very strong candidate for future energy saving applications. Within this work, the fabrication process for these micromirror arrays has been optimized and some steps for the large area fabrication of micromirror modules were performed. At first the surface roughness of the insulation layer of silicon dioxide (SiO2) was investigated. This SiO2 thin layer was deposited on three different type of substrates i.e. silicon, glass and Polyethylene Naphthalate (PEN) substrates. The deposition techniques which has been used are Plasma Enhanced Chemical Vapor Deposition (PECVD), Physical Vapor Deposition (PVD) and Ion Beam Sputter Deposition (IBSD). The thickness of the SiO2 thin layer was kept constant at 150nm for each deposition process. The surface roughness was measured by Stylus Profilometry and Atomic Force Microscopy (AFM). It was found that the layer which was deposited by IBSD has got the minimum surface roughness value and the layer which was deposited by PECVD process has the highest surface roughness value. During the same investigation, the substrate temperature of PECVD was varied from 80° C to 300° C with the step size of 40° C and it was found that the surface roughness keeps on increasing as the substrate holder temperature increases in the PECVD process. A new insulation layer system was proposed to minimize the dielectric breakdown effect in insulation layer for micromirror arrays. The conventional bilayer system was replaced by five layer system but the total thickness of insulation layer remains the same. It was found that during the actuation of micromirror arrays structure, the dielectric breakdown effect was reduced considerably as compared to the bilayer system. In the second step the fabrication process of the micromirror arrays was successfully adapted and transferred from glass substrates to the flexible PEN substrates by optimizing the conventional process recipe. In the last section, a large module of micromirror arrays was fabricated by electrically interconnecting four 10cm×10cm micromirror modules on a glass pane having dimensions of 21cm×21cm.

Subcutaneous study on the controlled release of Etanidazole and Taxol for the treatment of Glioma

BALB/c nude mice 6 weeks old were inoculated with glioma C6 cell-line and the efficacy of the different amount of Etanidazole-discs and Taxol-microspheres was investigated. Poly (D,L-lactic-co-glycolic acid) (PLGA) was used as the main encapsulating polymer and polyethylene glycol was added to increase the porosity. The 1% drug loading microspheres of each drug were produced by spray drying and the discs were obtained by compressing the Etanidazole-microspheres. Intra-tumoral injection followed by irradiation resulted in high systemic dosage and thus systemic toxicity. Tumors grown for 6 days, 9 days and 16 days were implanted with 0.5 mg or 1.0 mg or 1.5 mg of the drug. A radiation dosage of 2 Gy each time for a number of times was given for animals implanted with Etanidazole and no irradiation was given for animals implanted with Taxol. Increasing the number of doses clearly decreased the rate of tumor growth. The increase in the amount of drug on smaller sized tumors controlled the tumor better and there was agglomeration of the microspheres resulting in deviation of release profile of the drug as compared to the in vitro studies. It was observed that 1.0 mg of Taxol given to a tumor grown for 6 days was able to suppress the tumor for a total period of approximately two months and no tumor resurrection was observed during the second month.

The Inertio-Elastic Planar Entry Flow of Low-Viscosity Elastic Fluids in Micro-fabricated Geometries

The non-Newtonian flow of dilute aqueous polyethylene oxide (PEO) solutions through microfabricated planar abrupt contraction-expansions is investigated. The contraction geometries are fabricated from a high-resolution chrome mask and cross-linked PDMS gels using the tools of soft-lithography. The small length scales and high deformation rates in the contraction throat lead to significant extensional flow effects even with dilute polymer solutions having time constants on the order of milliseconds. The dimensionless extra pressure drop across the contraction increases by more than 200% and is accompanied by significant upstream vortex growth. Streak photography and videomicroscopy using epifluorescent particles shows that the flow ultimately becomes unstable and three-dimensional. The moderate Reynolds numbers (0.03 ≤ Re ≤ 44) associated with these high Deborah number (0 ≤ De ≤ 600) microfluidic flows results in the exploration of new regions of the Re-De parameter space in which the effects of both elasticity and inertia can be observed. Understanding such interactions will be increasingly important in microfluidic applications involving complex fluids and can best be interpreted in terms of the elasticity number, El = De/Re, which is independent of the flow kinematics and depends only on the fluid rheology and the characteristic size of the device.

La perdurabilidad del sector estratégico de empaques de polietileno de baja densidad en la localidad de los Mártires de la ciudad de Bogotá D.C.

El presente texto tiene como objetivo identificar las prácticas organizacionales relevantes en dirección y gerencia que han desarrollado las empresas dedicadas a la fabricación y comercialización de empaques de polietileno de baja densidad (PEBD), ubicadas en Los Mártires, las cuales permitieron que dichas empresas se mantuvieran en el mercado durante más de una década, siendo entonces exitosas en medio de circunstancias adversas. El trabajo se apoya en la reflexión de los aspectos, alcances y primordiales enseñanzas del uso del instrumento: “Estudio de condiciones para la perdurabilidad” (ECP), como resultado de las investigaciones que adelanta el Grupo de Investigación en Perdurabilidad Empresarial (GIPE) de la Universidad del Rosario, que sirve a modo de metodología innovadora como parámetro importante para futuros trabajos tanto académicos como de consultoría, sobre el comportamiento de las organizaciones y las dinámicas en las cuales se desempeñan. El documento presenta inicialmente los conceptos que conforman la propuesta del “Estudio de condiciones para la perdurabilidad” (ECP), el contexto de las cadenas productivas del sector de plásticos, las particularidades de la localidad en donde se ubican y las características de las “pymes” en la ciudad de Bogotá, para establecer las dimensiones más significativas del perfil que las identifica hasta la fecha; para de tal manera estudiar posteriormente la serie de componentes que evidencian las condiciones propias de perdurabilidad. Finalmente, se determinan algunas prácticas organizacionales que han funcionado en los últimos años en las “pymes” en el contexto empresarial de la ciudad de Bogotá D.C., y se concluye que la perdurabilidad de dichas empresas constituye el surgimiento de propiedades y procesos complejos del sistema de empresas en su conjunto, que no son reducibles a las propiedades o procesos de las empresas individuales.

Plan de exportaciones de Colpet ltda.

Este trabajo consta de cinco capítulos acerca de Colpet Ltda trata sobre el problema de contaminación del residuo sólido POLIETILENO TEREFTALATO (PET), material utilizado para la fabricación de envases.

Contribución al estudio de la extracción química del Fe3+ contaminante de la madera arqueológica subacuática impregnada con polietilenglicol

Due to the large quantity of contamination by Fe in the waterlogged wood and the composites previously processed with poliethilenglycol, PEG , we have thought the possible extraction and formation of complexes Fe-L (L= 2-Phosphonobuta-1,2,4- tricarboxylic acid, (PBTC)) and their effect on (i) structure of the wood, (ii) structure and physiques characteristics of PEG and (iii) post-treatment contamination by Fe coming from atmospheric agents. This work is a project for to study the formation of these complexes and possible modifications in structures.

Soluções sólidas vs. dispersões sólidas: impacto dos parâmetros de formulação

Filmes matriciais foram preparados com fármacos com diferentes solubilidades aquosas (tartarato de metoprolol, ibuprofeno e diclofenac Na) e diferentes polímeros (etilcelulose, Eudragit RS e Eudragit RL). Foram obtidas soluções sólidas (fármaco dissolvido) e dispersões sólidas (fármaco disperso). A libertação dos fármacos foi estudada em função do tipo de fármaco, doseamento, tipo e quantidade de aditivo e do tipo de polímero. A libertação dos fármacos não foi de acordo com a sua solubilidade aquosa, mas sim com o estado físico do fármaco na matriz. O incremento do conteúdo do fármaco na matriz aumentou a velocidade de libertação monotonicamente para a solução sólida. Em contraste, com a dispersão sólida, o aumento da dosagem de fármaco não originou quase nenhum efeito até 30 %, registando-se apenas, posteriormente, um acréscimo na sua velocidade. A inclusão de aditivos hidrofílicos aumentou principalmente a fase inicial do perfil de libertação do fármaco e não produziu efeito no plateau. Por outro lado, polietilenoglicol 1500 diminuiu a libertação de diclofenac Na devido ao aprisionamento do fármaco nos seus domínios. O efeito do tipo de polímero na libertação de ibuprofeno esteve relacionado com a partição do fármaco com o polímero. No caso do tartarato de metoprolol, a libertação foi muito mais rápida do da matriz de Eudragit RS do que de EC, devido à formação de uma mistura amorfa.

Defining Structure in Electrospun Polymer Fibres

We use a combination of microscopy, x-ray scattering and neutron scattering to show how structure develops in micro and nano-size polymer fibres prepared by electrospinning. The technique has been applied to a range of different polymers, an amorphous system (polystyrene), a crystallisable polymer (poly-epsilon-caprolactone), a composite systems (polyethylene oxide or poly vinyl alcohol containing polypyrrole) and consider the possibility of self assembly (gelatin).

Linear nucleation of polymers

The use of high-melting fibres as linear nuclei for quiescent polymeric melts is instrumental in providing the superior mechanical properties of polymeric self-composites. It also has inherent advantages in the elucidation of fundamental aspects of polymeric crystallization and self-organization, not least in allowing systematic microscopic studies of polymeric crystallization from nucleation through to the growth interface. This has demonstrated explicitly that lamellae develop in two distinct ways, for slower and faster growth, depending on whether fold packing has or has not time to order before the next molecular layer is added with only the former leading to banded growth in linear polyethylene. Other gains in understanding concern cellulation and morphological instability, internuclear interference, isothermal lamellar thickening and banded growth being a consequence of the partial relief of initial surface stress. (c) 2006 Elsevier Ltd. All rights reserved.

A critical assessment of unbalanced surface stresses: Some complementary considerations

The wide-ranging survey of twisted growth in polymers by Lotz and Cheng cites extensive evidence consistent with the relief of surface stress being the underlying cause. This complementary note contributes to the discussion by making three main points. First, it is necessary to go further and explain the key issue of how a consistent twist is maintained when, as commonly, this habit has a lower symmetry than the crystallographic lattice. Detailed study has shown that, in polyethylene, this occurs by reorganization of the initial fold surfaces. Second, the suggested explanation by Keith and Padden that. in polyethylene, the asymmetric habit derives from molecules adding to lamellae with inclined fold surfaces is invalid being doubly inconsistent with observation. Third, twisting has now been linked to faster growth by study of row structures in polyethylene. This produces inherently rough fold surfaces in Regime II whose internal stresses drive reorganization and twisting. For slower (Regime I) growth, fold surfaces form with and maintain ordered packing so providing no basis for twisting. These new insights radically alter the context of twisted growth and provide a firm factual basis for further work. (c) 2005 Elsevier Ltd. All rights reserved.

A high efficiency technique for the generation of transgenic sugar beets from stomatal guard cells

An optimized protocol has been developed for the efficient and rapid genetic modification of sugar beet (Beta vulgaris L.). A polyethylene glycol-mediated DNA transformation technique could be applied to protoplast populations enriched specifically for a single totipotent cell type derived from stomatal guard cells, to achieve high transformation frequencies. Bialaphos resistance, conferred by the pat gene, produced a highly efficient selection system. The majority of plants were obtained within 8 to 9 weeks and were appropriate for plant breeding purposes. All were resistant to glufosinate-ammonium-based herbicides. Detailed genomic characterization has verified transgene integration, and progeny analysis showed Mendelian inheritance.

Seed storage of Avicennia alba B1

Seeds of Avicennia alba BI. matured at high moisture content and were sensitive to desiccation: no seeds survived desiccation below 35% moisture content. The effect on survival of a factorial combination of five moist storage treatments (fresh seeds in a polyethylene bag, open with water sprayed over regularly, mixed with sand at 10% moisture content, mixed with moist paddy hulls, or naked seeds mixed with sand at 10% moisture content) and three temperatures (28-30degreesC, 17degreesC and 8-10degreesC) was investigated. In addition, seeds were mixed with sand at 5% moisture content and stored at 17degreesC in order to determine the effect of sand moisture content on seed moisture content and viability during storage. Avicennia alba showed recalcitrant seed storage behaviour, but 75% of the seeds remained viable after four months' moist (45-47% moisture content) storage in 10% moisture content sand at 17degreesC.

Drying method influences the development of germinability, dessication tolerance and subsequent longevity of immature seeds of sumauma (Ceiba pentandra (L.) Gaertn. [Bombacaceae])

The ability to germinate, tolerate desiccation and survive in air-dry storage was investigated during early seed development in planta and subsequent ex planta maturation of sumauma (Ceiba pentandra). Immature fruits were collected on three different dates (i.e. from about 5 days before until 7 days after mass maturity). Immature fresh seeds were not able to germinate. Fruits or seeds were subjected immediately after each collection to three different drying treatments with progressively slower rates of dessication: (i) seeds were extracted from the fruits and dried immediately; (ii) fruits were dried in a thin layer; (iii) fruits were dried in a tied polyethylene bag (with 10 holes of 1cm diameter). Drying was in a room maintained at 25 degrees C +/- 3 degrees C and 65%+/- 5% r.h. For treatment (i) the seeds were dried for 6 days in order to reduce moisture content to around 13% ( +/- 2%) moisture content. For treatments (ii) and (iii) the fruits were subjected to different periods of drying depending upon collection date. The results of these post-collection treatments showed generally that the more immature the seeds the slower the rate of drying that is required to improve ability to germinate, ability to tolerate desiccation and potential longevity, but at the third harvest, 7 days after mass maturity, the intermediate drying rate treatment was the most beneficial. Thus post fruit collection treatments can be modified depending upon the stage of seed development in order to provide good to high quality seeds of sumauma when collection has to be made at a site with difficult access at less than ideal times. The results are relevant to seed collection practices for both forestry and ex situ plant biodiversity conservation.

Effects of volatile fatty acid supply on their absorption and on water kinetics in the rumen of sheep sustained by intragastric infusions

Three sheep fitted with a ruminal cannula and an abomasal catheter were used to study water kinetics and absorption of VFA infused continuously into the rumen. The effects of changing VFA concentrations in the rumen by shifting VFA infusion rates were investigated in an experiment with a 3 x 3 Latin square design. On experimental days, the animals received the basal infusion rate of VFA (271 mmol/h) during the first 2 h. Each animal then received VFA at a different rate (135, 394, or 511 mmol/h) for the next 7.5 h. Using soluble markers (polyethylene glycol and Cr-EDTA), ruminal volume, liquid outflow, apparent water absorption, and VFA absorption rates were estimated. There were no significant effects of VFA infusion rate on ruminal volume and water kinetics. As the VFA infusion rate was increased, VFA concentration and osmolality in the rumen were increased and pH was decreased. There was a biphasic response of liquid outflow to changes in the total VFA concentration in the rumen, as both variables increased together up to a total VFA concentration of 80.1 mM, whereas, beyond that concentration, liquid outflow remained stable at an average rate of 407 mL/h. There were significant linear (P = 0.003) and quadratic (P = 0.001) effects of VFA infusion rate on the VFA absorption rate, confirming that VFA absorption in the rumen is mainly a concentration-dependent process. The proportion of total VFA supplied that was absorbed in the rumen was 0.845 (0.822, 0.877, and 0.910 for acetate, propionate, and butyrate, respectively). The molar proportions of acetate, propionate, and butyrate absorbed were affected by the level of VFA infusion in the rumen, indicating that this level affected to a different extent the absorption of the different acids.