Active vibration control using delayed resonant feedback

Delayed feedback (DF) control is a well-established technique to suppress single frequency vibration of a non-minimum phase system. Modal control is also a well-established technique to control multiple vibration modes of a minimum phase system. In this paper these techniques are combined to simultaneously suppress multiple vibration modes of a non-minimum phase system involving a small time delay. The control approach is called delayed resonant feedback (DRF) where each modal controller consists of a modal filter to extract the target mode signal from the vibration response, and a phase compensator to account for the phase delay of the mode. The methodology is first discussed using a single mode system. A multi-mode system is then studied and experimental results are presented to demonstrate the efficacy of the control approach for two modes of a beam. It is shown that the system behaves as if each mode under control has a dynamic vibration absorber attached to it, even though the actuator and the sensor are not collocated and there is a time delay in the control system. © 2013 IOP Publishing Ltd.

Corpus Luteum Development and Function after Supplementation of Long-Acting Progesterone During the Early Luteal Phase in Beef Cattle

Contents: Strategic supplementation of P4 may be used to increase conception rates in cattle, but timing of supplementation in relation to ovulation, mass of supplementary P4 and formulation of the P4-containing supplement has not been determined for beef cattle. Effects of supplementation of long-acting progesterone (P4) on Days 2 or 3 post-ovulation on development, function and regression of corpus luteum (CL) were studied in beef cattle. Cows were synchronized with an oestradiol/P4-based protocol and treated with 150 or 300 mg of long-acting P4 on Day 2 or 3 post-ovulation (6-7 cows/group). Colour-doppler ultrasound scanning and blood sample collection were performed from Day 2-21.5. Plasma P4 concentrations were greater (p < 0.05) from Day 2.5-5.5 in the Day 2-treated groups and from Day 3.5-5.5 in the Day 3-treated cows than in the control group. CL area and blood flow during Day 2-8.5 did not differ (p > 0.05) among groups, suggesting no effect of P4 treatment on luteal development. The frequency of cows that began luteolysis before Day 15 was greater (p < 0.04) in cows treated with 300 mg than in the controls, but there were no differences between non-treated and 150 mg-treated cows. The interval from pre-treatment ovulation to functional and structural luteolysis was shorter (p < 0.01) in the combined P4-treated groups than in the control cows. In conclusion, was showed for the first time that long-acting P4 supplementation on Day 2 or 3 post-ovulation increases P4 concentrations for ≥3 day, has no effect on luteal development, but anticipates the beginning of luteolysis in beef cattle. © 2013 Blackwell Verlag GmbH.

On the control of vibrations using synchrophasing

This paper describes the application of a technique, known as synchrophasing, to the control of machinery vibration. It is applicable to machinery installations, in which several synchronous machines, such as those driven by electrical motors, are fitted to an isolated common structure known as a machinery raft. To reduce the vibration transmitted to the host structure to which the machinery raft is attached, the phase of the electrical supply to the motors is adjusted so that the net transmitted force to the host structure is minimised. It is shown that while this is relatively simple for an installation consisting of two machines, it is more complicated for installations in which there are more than two machines, because of the interaction between the forces generated by each machine. The development of a synchrophasing scheme, which has been applied to propeller aircraft, and is known as Propeller Signature Theory (PST) is discussed. It is shown both theoretically and experimentally, that this is an efficient way of controlling the phase of multiple machines. It is also shown that synchrophasing is a worthwhile vibration control technique, which has the potential to suppress vibration transmitted to the host structure by up to 20 dB at certain frequencies. Although the principle of synchronisation has been demonstrated on a one-dimensional structure, it is believed that this captures the key features of the approach. However, it should be realised that the mode-shapes of a machinery raft may be more complex than that of a one-dimensional structure and this may need to be taken into account in a real application. © 2013 Elsevier Ltd.

Air-particle abrasion on zirconia ceramic using different protocols: Effects on biaxial flexural strength after cyclic loading, phase transformation and surface topography

This study evaluated the effect of different air-particle abrasion protocols on the biaxial flexural strength and structural stability of zirconia ceramics. Zirconia ceramic specimens (ISO 6872) (Lava, 3M ESPE) were obtained (N=336). The specimens (N=118, n=20 per group) were randomly assigned to one of the air-abrasion protocols: Gr1: Control (as-sintered); Gr2: 50 μm Al2O3 (2.5 bar); Gr3: 50 μm Al2O3 (3.5 bar); Gr4: 110 μm Al2O3(2.5 bar); Gr5: 110 μm Al2O3 (3.5 bar); Gr6: 30 μm SiO2 (2.5 bar) (CoJet); Gr7: 30 μm SiO2(3.5 bar); Gr8: 110 μm SiO2 (2.5 bar) (Rocatec Plus); and Gr9: 110 μm SiO2 (3.5 bar) (duration: 20 s, distance: 10 mm). While half of the specimens were tested immediately, the other half was subjected to cyclic loading in water (100,000 cycles; 50 N, 4 Hz, 37 °°C) prior to biaxial flexural strength test (ISO 6872). Phase transformation (t→m), relative amount of transformed monoclinic zirconia (FM), transformed zone depth (TZD) and surface roughness were measured. Particle type (p=0.2746), pressure (p=0.5084) and cyclic loading (p=0.1610) did not influence the flexural strength. Except for the air-abraded group with 110 μm Al2O3 at 3.5 bar, all air-abrasion protocols increased the biaxial flexural strength (MPa) (Controlnon-aged: 1030±153, Controlaged: 1138±138; Experimentalnon-aged: 1307±184-1554±124; Experimentalaged: 1308±118-1451±135) in both non-aged and aged conditions, respectively. Surface roughness (Ra) was the highest with 110 μm Al2O3(0.84 μm. FM values ranged from 0% to 27.21%, higher value for the Rocatec Plus (110 μm SiO2) and 110 μm Al2O3 groups at 3.5 bar pressure. TZD ranged between 0 and 1.43 μm, with the highest values for Rocatec Plus and 110 μm Al2O3 groups at 3.5 bar pressure. © 2013 Elsevier Ltd.

Three-phase tri-state buck-boost integrated inverter

This paper presents a three-phase integrated inverter suitable for stand-alone and/or grid-connected applications. The usage of the special features of the tri-state coupled with the special space vector modulation allows the inverter to present an attractive degree of freedom for the controllers' design, i.e. input and output can be controlled independently. Additionally all controllers are based on dq0 transformation, the system are described and interesting simulation results are available to confirm the proposal. Finally, this paper presents experimental evaluations of the inverter feeding a three-phase stand-alone load confirming the remarkable features of the decoupling control. © 2013 IEEE.

Estudo da estabilidade a pequenas perturbações do sistema elétrico de potência sob a ação do dispositivo FACTS PHASE SHIFTER - PS

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Impact of muscle fatigue on mechanics and motor control of walking

Pós-graduação em Ciências da Motricidade - IBRC

Evaluation via multivariate techniques of scale factor variability in the rietveld method applied to quantitative phase analysis with X ray powder diffraction

ABSTRACT: The present work uses multivariate statistical analysis as a form of establishing the main sources of error in the Quantitative Phase Analysis (QPA) using the Rietveld method. The quantitative determination of crystalline phases using x ray powder diffraction is a complex measurement process whose results are influenced by several factors. Ternary mixtures of Al2O3, MgO and NiO were prepared under controlled conditions and the diffractions were obtained using the Bragg-Brentano geometric arrangement. It was possible to establish four sources of critical variations: the experimental absorption and the scale factor of NiO, which is the phase with the greatest linear absorption coefficient of the ternary mixture; the instrumental characteristics represented by mechanical errors of the goniometer and sample displacement; the other two phases (Al2O3 and MgO); and the temperature and relative humidity of the air in the laboratory. The error sources excessively impair the QPA with the Rietveld method. Therefore it becomes necessary to control them during the measurement procedure.

Photosynthetic capacity and water use efficiency in sugarcane genotypes subject to water deficit during early growth phase

The objective of this study was to compare the gas exchange, photosynthetic capacity and water potential of sugarcane genotypes cultivated under water deficit conditions imposed during the initial growth phase. Experiments were performed in a greenhouse using two sugarcane genotypes namely: HoCP93-776 (drought susceptible) and TCP02-4587 (drought tolerant). Sixty days after planting, two different water treatments were applied (i.e., with or without water deficit). At 0,30 and 60 days after the treatment, gas exchange variables were evaluated for their relationship with water use, intrinsic instantaneous water use efficiency and instantaneous carboxylation efficiency. The SPAD index, photosynthetic pigments, water potential and relative water content in the leaves were also analyzed. The genotype HoCP93-776 was more sensitive to drought treatment as indicated by the significantly lower values of SPAD index, photosynthetic pigments, water potential (Ψw) and relative water content (RWC) variables. The genotype TCP02-4587 had higher water potential, stomatal control efficiency, water use efficiency (WUE), intrinsic instantaneous water use efficiency (WUEintr), instantaneous carboxylation efficiency and photosynthetic capacity. The highest air vapor pressure deficit during the drought conditions could be due to the stomatal closing in the HoCP93-776, which contributed to its lower photosynthetic capacity.

Use of live oocyst vaccine in the control of turkey coccidiosis: Effect on performance and intestinal morphology

An experiment was conducted to determine the effects of different coccidiosis-preventing programs on performance and intestinal morphology of commercial turkeys. Three hundred fifteen1-d-old female commercial cross turkey poults (British United Turkeys, BUT Big 9) were distributed into 3 treatments with 5 replicates of 21 birds each. Three programs were evaluated from 1 to 70 d of age, where program 1 had no anticoccidial drug and no vaccination against coccidiosis; program 2 had an anticoccidial drug (maduramycin 1%, 5 ppm); and program 3 had a vaccination (commercial vaccine, 4 species of Eimeria). All the groups were challenged with a dose of oocysts sporulated (20,000/bird) of 2 species of Eimeria at 21 d of age. In the growing phase (d 0-28), BW, BW gain, and FCR were significantly greater in treated groups compared with control group. In the fattening phase, the performance was not affected by treatments. Treatments and coccidiosis challenge had no significant effects on intestinal villus height. These observations support other reports that confirm live oocyst vaccination can be used effectively as a preventive against avian coccidiosis in commercially reared turkeys.

Validation of analytical methodology for quantification of cefazolin sodium pharmaceutical dosage form by high performance liquid chromatography to be applied for quality control in pharmaceutical industry

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Instantaneous Phase Threshold for Reflector Detection in Ultrasonic Images

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Demonstration of non-collocated vibration control of a flexible manipulator using electrical dynamic absorbers

This paper describes an experimental study into the vibration control of a servo system comprising a servo motor and a flexible manipulator. Two modes of the system are controlled by using the servo motor and an accelerometer attached to the tip of the flexible manipulator. The control system is thus non-collocated. It consists of two electrical dynamic absorbers, each of which consists of a modal filter and, in case of an out-of-phase mode, a phase inverter. The experimental results show that each absorber acts as a mechanical dynamic vibration absorber attached to each mode and significantly reduces the settling time for the system response to a step input.

Dyslexic children suffer from less informative visual cues to control posture

The goal of this study was to investigate the effects of manipulation of the characteristics of visual stimulus on postural control in dyslexic children. A total of 18 dyslexic and 18 non-dyslexic children stood upright inside a moving room, as still as possible, and looked at a target at different conditions of distance between the participant and a moving room frontal wall (25-150 cm) and vision (full and central). The first trial was performed without vision (baseline). Then four trials were performed in which the room remained stationary and eight trials with the room moving, lasting 60 s each. Mean sway amplitude, coherence, relative phase, and angular deviation were calculated. The results revealed that dyslexic children swayed with larger magnitude in both stationary and moving conditions. When the room remained stationary, all children showed larger body sway magnitude at 150 cm distance. Dyslexic children showed larger body sway magnitude in central compared to full vision condition. In the moving condition, body sway magnitude was similar between dyslexic and non-dyslexic children but the coupling between visual information and body sway was weaker in dyslexic children. Moreover, in the absence of peripheral visual cues, induced body sway in dyslexic children was temporally delayed regarding visual stimulus. Taken together, these results indicate that poor postural control performance in dyslexic children is related to how sensory information is acquired from the environment and used to produce postural responses. In conditions in which sensory cues are less informative, dyslexic children take longer to process sensory stimuli in order to obtain precise information, which leads to performance deterioration. (C) 2014 Elsevier Ltd. All rights reserved.

Effect of particle size on the flexural strength and phase transformation of an airborne-particle abraded yttria-stabilized tetragonal zirconia polycrystal ceramic.

Statement of problem Because airborne-particle abrasion is an efficient method of improving the bond at the zirconia-cement interface, understanding its effect on the strength of yttria-stabilized tetragonal zirconia polycrystal is important. Purpose The purpose of this study was to evaluate the effect of the particle size used for airborne-particle abrasion on the flexural strength and phase transformation of a commercially available yttria-stabilized tetragonal zirconia polycrystal ceramic. Material and Methods For both flexural strength (20.0 × 4.0 × 1.2 mm) (n=14) and phase transformation (14.0-mm diameter × 1.3-mm thickness) (n=4), the zirconia specimens were made from Lava, and their surfaces were treated in the following ways: as-sintered (control); with 50-μm aluminum oxide (Al2O3) particles; with 120-μm Al2O3 particles; with 250-μm Al2O3 particles; with 30-μm silica-modified Al2O3 particles (Cojet Sand); with 120-μm Al2O3 particles, followed by 110-μm silica-modified Al2O3 particles (Rocatec Plus); and with Rocatec Plus. The phase transformation (%) was assessed by x-ray diffraction analysis. The 3-point flexural strength test was conducted in artificial saliva at 37°C in a mechanical testing machine. The data were analyzed by 1-way ANOVA and the Tukey honestly significant difference post hoc test (α=.05). Results Except for the Cojet Sand group, which exhibited statistically similar flexural strength to that of the as-sintered group and for the group abraded with 250-μm Al2O3 particles, which presented the lowest strength, airborne-particle abrasion with the other particle sizes provided the highest values, with no significant difference among them. The as-sintered specimens presented no monoclinic phase. The groups abraded with smaller particles (30 μm and 50 μm) and those treated with the larger ones (110 μm and/or 120 μm particles and 250 μm) exhibited percentages of monoclinic phase that varied from 4% to 5% and from 8.7% to 10%. Conclusions Except for abrasion with Cojet Sand, depending on the particle size, zirconia exhibited an increase or a decrease in its flexural strength. Airborne-particle abrasion promoted phase transformation (tetragonal to monoclinic), and the percentage of monoclinic phase varied according to the particle size.