Axial buckling load of partially encased columns under fire

Partially encased columns have significant fire resistant. However, it is not possible to assess the fire resistance of such members simply by considering the temperature of the steel. The presence of concrete increases the mass and thermal inertia of the member and the variation of temperature within the cross section, in both the steel and concrete components. The annex G of EN1994-1-2 allows to calculate the load carrying capacity of partially encased columns, for a specific fire rating time, considering the balanced summation method. New formulas will be used to calculate the plastic resistance to axial compression and the effective flexural stiffness. These two parameters are used to calculate the buckling resistance. The finite element method is used to compare the results of the elastic critical load for different fire ratings of 30 and 60 minutes. The buckling resistance is also calculated by the finite element method, using an incremental and iterative procedure. This buckling resistance is also compared with the simple calculation method, evaluating the design buckling curve that best fits the results.

NUTRITIONAL AND AMINO ACID ANALYSIS OF RAW, PARTIALLY FERMENTED AND COMPLETELY FERMENTED LOCUST BEAN ( Parkia biglobosa ) SEEDS

The nutritional and amino acid analysis of raw and fermented seeds of Parkia biglobosa were carried out. Parameters investigated include moisture, crude protein, crude fat, ash, crude fibre and mineral contents; and the effect of the degree of fermentation on these parameters was also investigated. The amino acid compositions of all the samples were evaluated and amino acid quality determined by calculating amino acid scores and the predicted protein efficiency ratio (P-PER). Results showed that the proximate composition was significantly affected by fermentation, although there was little difference between the parameters for the partially fermented and completely fermented samples. Based on dry matter percentage, protein content was in the 39.77 – 43.74 % range while crude fibre ranged between 5.55 – 7.42 %. The ash content was lowest in the raw sample (2.34 %), while the fermented samples had ash contents between 4.27 and 8.33 % for the fully fermented and the partially fermented seeds, respectively. The fat content increased from 8.65 % in the raw seed to 24.4 % and 27.6 % for the partially and completely fermented samples, respectively. Results of the amino acid analysis showed that the partially fermented sample had the lowest quantities of all amino acids determined and had lysine as the limiting amino acid, whereas the raw and completely fermented samples had very similar amino acid profile with amino acid scores of 100, indicating that there are no limiting amino acids. All the samples were rich in essential amino acids. The P-PER also showed that the partially fermented sample had the lowest protein efficiency while the raw seed had the highest. Mineral contents generally increased from the raw, through the partially fermented, to the completely fermented seeds and results showed the samples to be good sources of potassium (K), calcium (Ca), manganese (Mn) and copper (Cu) in addition to being complementary sources of other metals. Locust bean seed does not accumulate lead and is, therefore, safe for consumption without the potential of food poisoning.

Survey design: Insights from a public sector ERP success story

Research on the impact of Information Systems (IS) reported in both academic literature and popular press has reported confounding results. Some studies have reported encouraging results of IS, while others have reported nil or detrimental results. The contradictory results of these research studies can be partially attributed to the weaknesses in survey instruments. In an attempt to increase the validity of conclusions of IS assessment studies, survey instrument design should follow a rigorous and scientific procedure. This paper illustrates key validity and reliability issues in measuring Information Systems performance, using examples from a study designed to assess Enterprise Resource Planning systems success. The article emphasizes on the importance of the survey method and the theoretical considerations of item derivation, scale development and item evaluation. Examples are provided from the ERP assessment study to supplement the readers understanding of the theoretical concepts of survey design.

Stretching-induced orientation to improve mechanical properties of electrospun pan nanocomposites

Partially aligned and oriented polyacrylonitrile(PAN)-based nanofibers were electrospun from PAN and SWNTs/PAN in the solution of dimethylformamide(DMF) to make the carbon nanofibers. The as-spun nanofibers were hot-stretched in an oven to enhance its orientation and crystallinity. Then it were stabilized at 250 square under a stretched stress, and carbonized at 1000 square in N-2 atmosphere by fixing the length of the stabilized nanofiber to convert them into carbon nanofibers. With this hot-stretched process and with the introduction of SWNTs, the mechanical properties will be enhanced correspondingly. The crystallinity of the stretched fibers confirmed by X-ray diffraction has also increased. For PAN nanofibers, the improved fiber alignment and crystallinity resulted in the increased mechanical properties, such as the modulus and tensile strength of the nanofibers. It was concluded that the hot-stretched nanofiber and the SWNTs/PAN nanofibers can be used as a potential precursor to produce high-performance carbon composites.

Corporate social responsibility and sport event sponsorship

Demonstrating socially responsible behaviour has become increasingly important for corporations. Using the Psychological Continuum Model (PCM) as its theoretical framework, this paper examines the meditational role of corporate social responsibility (CSR) on the relationship between sport participation motivation, event attachment and purchase intent of a sport event’s sponsors’ products. A questionnaire was distributed to a sample of sport event participants (N=689) to measure sport participation motivation (recreation and charity), attachment to the event, CSR, and purchase intent of sponsors’ products. Results reveal that CSR fully mediates the link between purchase intent and sport participation motivation and partially mediates the influence of attachment on purchase intent. The authors propose that corporations strategically align with sport events in which participants are attached to allow for CSR and the meaning elicited by the event to work jointly.

Towards a literacy of attention

In 1997, business trend analyst Linda Stone proposed the term "continuous partial attention" to characterise the contemporary experience of wanting to be ‘a live node on the network’. She argued that while it can be a positive and functional behaviour, it also has the potential to be disabling, compromising reflective and creative thought. Subsequent studies have explored the ways in which technology has slowly disrupted the idea and experience of a "centred" and "bounded" self. Studies of ‘Gen Y’ show the ease with which young people accommodate this multiplying of the self as they negotiate their partial friendships and networks of interest with family and work. In teaching and learning circles in tertiary education we talk a lot about problems of student ‘disengagement’. In characterising our challenge this way, are we undermining our potential to understand the tendencies of contemporary learners? This paper begins a consideration of how traditional models, frameworks and practices might oppose these partially engaged but continuously connected and interpersonal "dividuals". What questions does this provoke for learning environments towards harnessing yet counterpointing the crisis students might experience; to recognise but also integrate their multiple selves towards what they aim to become through the process of learning?

The Euro-American psyche and the imaging of Samoa in the early 20th century

Drawing on English language sources and material from Western Samoa (now Samoa), this examination of photographically illustrated serial encyclopaedia and magazines proposes an alternative historical analysis of the colonial photographs of Samoa, the most extensively covered field in Oceanic photographic studies. Photographs published between the 1890s and World War II were not necessarily from that era, and despite claims in the text of illustrated publications of an unchanged, enduring, archaic tradition in Samoa, the amazing variety of content and subject matter often offered contradictory evidence, depicting a modern, adaptive and progressive Samoa. Contrary to orthodox historical analysis, the images of Samoa in illustrated magazines and encyclopaedia were not limited to a small, repetitive gallery of partially clothed women and costumed chiefs.

Exploring the influence of a science content course incorporating explicit nature of science and argumentation instruction on preservice primary teachers' views of nature of science

There exists a general consensus in the science education literature around the goal of enhancing students. and teachers. views of nature of science (NOS). An emerging area of research in science education explores NOS and argumentation, and the aim of this study was to explore the effectiveness of a science content course incorporating explicit NOS and argumentation instruction on preservice primary teachers. views of NOS. A constructivist perspective guided the study, and the research strategy employed was case study research. Five preservice primary teachers were selected for intensive investigation in the study, which incorporated explicit NOS and argumentation instruction, and utilised scientific and socioscientific contexts for argumentation to provide opportunities for participants to apply their NOS understandings to their arguments. Four primary sources of data were used to provide evidence for the interpretations, recommendations, and implications that emerged from the study. These data sources included questionnaires and surveys, interviews, audio- and video-taped class sessions, and written artefacts. Data analysis involved the formation of various assertions that informed the major findings of the study, and a variety of validity and ethical protocols were considered during the analysis to ensure the findings and interpretations emerging from the data were valid. Results indicated that the science content course was effective in enabling four of the five participants. views of NOS to be changed. All of the participants expressed predominantly limited views of the majority of the examined NOS aspects at the commencement of the study. Many positive changes were evident at the end of the study with four of the five participants expressing partially informed and/or informed views of the majority of the examined NOS aspects. A critical analysis of the effectiveness of the various course components designed to facilitate the development of participants‟ views of NOS in the study, led to the identification of three factors that mediated the development of participants‟ NOS views: (a) contextual factors (including context of argumentation, and mode of argumentation), (b) task-specific factors (including argumentation scaffolds, epistemological probes, and consideration of alternative data and explanations), and (c) personal factors (including perceived previous knowledge about NOS, appreciation of the importance and utility value of NOS, and durability and persistence of pre-existing beliefs). A consideration of the above factors informs recommendations for future studies that seek to incorporate explicit NOS and argumentation instruction as a context for learning about NOS.

Water uptake of aerosols with a focus on seeded aerosols and instrumentation techniques

This thesis focuses on the volatile and hygroscopic properties of mixed aerosol species. In particular, the influence organic species of varying solubility have upon seed aerosols. Aerosol studies were conducted at the Paul Scherrer Institut Laboratory for Atmospheric Chemistry (PSI-LAC, Villigen, Switzerland) and at the Queensland University of Technology International Laboratory for Air Quality and Health (QUT-ILAQH, Brisbane, Australia). The primary measurement tool employed in this program was the Volatilisation and Hygroscopicity Tandem Differential Mobility Analyser (VHTDMA - Johnson et al. 2004). This system was initially developed at QUT within the ILAQH and was completely re-developed as part of this project (see Section 1.4 for a description of this process). The new VHTDMA was deployed to the PSI-LAC where an analysis of the volatile and hygroscopic properties of ammonium sulphate seeds coated with organic species formed from the photo-oxidation of á-pinene was conducted. This investigation was driven by a desire to understand the influence of atmospherically prevalent organics upon water uptake by material with cloud forming capabilities. Of particular note from this campaign were observed influences of partially soluble organic coatings upon inorganic ammonium sulphate seeds above and below their deliquescence relative humidity (DRH). Above the DRH of the seed increasing the volume fraction of the organic component was shown to reduce the water uptake of the mixed particle. Below the DRH the organic was shown to activate the water uptake of the seed. This was the first time this effect had been observed for á-pinene derived SOA. In contrast with the simulated aerosols generated at the PSI-LAC a case study of the volatile and hygroscopic properties of diesel emissions was undertaken. During this stage of the project ternary nucleation was shown, for the first time, to be one of the processes involved in formation of diesel particulate matter. Furthermore, these particles were shown to be coated with a volatile hydrophobic material which prevented the water uptake of the highly hygroscopic material below. This result was a first and indicated that previous studies into the hygroscopicity of diesel emission had erroneously reported the particles to be hydrophobic. Both of these results contradict the previously upheld Zdanovksii-Stokes-Robinson (ZSR) additive rule for water uptake by mixed species. This is an important contribution as it adds to the weight of evidence that limits the validity of this rule.

Effective web service discovery using a combination of a semantic model and a data mining technique

With the advent of Service Oriented Architecture, Web Services have gained tremendous popularity. Due to the availability of a large number of Web services, finding an appropriate Web service according to the requirement of the user is a challenge. This warrants the need to establish an effective and reliable process of Web service discovery. A considerable body of research has emerged to develop methods to improve the accuracy of Web service discovery to match the best service. The process of Web service discovery results in suggesting many individual services that partially fulfil the user’s interest. By considering the semantic relationships of words used in describing the services as well as the use of input and output parameters can lead to accurate Web service discovery. Appropriate linking of individual matched services should fully satisfy the requirements which the user is looking for. This research proposes to integrate a semantic model and a data mining technique to enhance the accuracy of Web service discovery. A novel three-phase Web service discovery methodology has been proposed. The first phase performs match-making to find semantically similar Web services for a user query. In order to perform semantic analysis on the content present in the Web service description language document, the support-based latent semantic kernel is constructed using an innovative concept of binning and merging on the large quantity of text documents covering diverse areas of domain of knowledge. The use of a generic latent semantic kernel constructed with a large number of terms helps to find the hidden meaning of the query terms which otherwise could not be found. Sometimes a single Web service is unable to fully satisfy the requirement of the user. In such cases, a composition of multiple inter-related Web services is presented to the user. The task of checking the possibility of linking multiple Web services is done in the second phase. Once the feasibility of linking Web services is checked, the objective is to provide the user with the best composition of Web services. In the link analysis phase, the Web services are modelled as nodes of a graph and an allpair shortest-path algorithm is applied to find the optimum path at the minimum cost for traversal. The third phase which is the system integration, integrates the results from the preceding two phases by using an original fusion algorithm in the fusion engine. Finally, the recommendation engine which is an integral part of the system integration phase makes the final recommendations including individual and composite Web services to the user. In order to evaluate the performance of the proposed method, extensive experimentation has been performed. Results of the proposed support-based semantic kernel method of Web service discovery are compared with the results of the standard keyword-based information-retrieval method and a clustering-based machine-learning method of Web service discovery. The proposed method outperforms both information-retrieval and machine-learning based methods. Experimental results and statistical analysis also show that the best Web services compositions are obtained by considering 10 to 15 Web services that are found in phase-I for linking. Empirical results also ascertain that the fusion engine boosts the accuracy of Web service discovery by combining the inputs from both the semantic analysis (phase-I) and the link analysis (phase-II) in a systematic fashion. Overall, the accuracy of Web service discovery with the proposed method shows a significant improvement over traditional discovery methods.

Life cycle inventory for Australian building materials

This paper discusses challenges to developers of a national Life Cycle Inventory (LCI) database on which to base assessment of building environmental impacts and a key to development of a fully integrated eco-design tool created for automated eco-efficiency assessment of commercial building design direct from 3D CAD. The scope of this database includes Australian and overseas processing burdens involved in acquiring, processing, transporting, fabricating, finishing and using metals, masonry, timber, glazing, ceramics, plastics, fittings, composites and coatings. Burdens are classified, calculated and reported for all flows of raw materials, fuels, energy and emissions to and from the air, soil and water associated with typical products and services in building construction, fitout and operation. The aggregated life cycle inventory data provides the capacity to generate environmental impact assessment reports based on accepted performance indicators. Practitioners can identify hot spots showing high environmental burdens of a proposed design and drill down to report on specific building components. They can compare assessments with case studies and operational estimates to assist in eco-efficient design of a building, fitout and operation.

Load during prosthetic gait : is direct measurement better than inverse dynamics?

The knee forces and moments estimated by inverse dynamics and directly measured by a multiaxial transducer were compared during the gait of a transfemoral amputee. The estimated and directly measured forces and moments were relatively close. However, 3D inverse dynamics estimated only partially the forces and moments associated with the deformation of the prosthetic foot and locking of knee mechanism.

Loading applied on prosthetic knee of transfemoral amputee: comparison of inverse dynamics and direct measurements

Inverse dynamics is the most comprehensive method that gives access to the net joint forces and moments during walking. However it is based on assumptions (i.e., rigid segments linked by ideal joints) and it is known to be sensitive to the input data (e.g., kinematic derivatives, positions of joint centres and centre of pressure, inertial parameters). Alternatively, transducers can be used to measure directly the load applied on the residuum of transfemoral amputees. So, the purpose of this study was to compare the forces and moments applied on a prosthetic knee measured directly with the ones calculated by three inverse dynamics computations - corresponding to 3 and 2 segments, and « ground reaction vector technique » - during the gait of one patient. The maximum RMSEs between the estimated and directly measured forces (i.e., 56 N) and moment (i.e., 5 N.m) were relatively small. However the dynamic outcomes of the prosthetic components (i.e., absorption of the foot, friction and limit stop of the knee) were only partially assessed with inverse dynamic methods.

A study of Australian company responses to email complaints

As businesses and organisations move online, many question how to use Internet communication tools effectively, such as Web sites and electronic mail (Porter, 2001). Where and how should they invest their time and money in technology? This research explores a small part of this broad question, online complaining and electronic customer service. This paper extends prior US-based research of consumer complaints by email (Strauss and Hill, 2001) in several ways. First, it replicates their research in an Australian setting. Second, this research addresses several future research issues that Strauss and Hill (2001) raised. And third, this paper uses diffusion of innovation (Rogers, 1995) to explain some of the results. The results partially support the findings of Strauss and Hill (2001), take a small step towards further investigation of effective email responses and provide practical suggestions for better email customer service.