A packaging technique for silicon MEMS strain sensors on steel

A packaging technique suited to applying MEMS strain sensors realized on a silicon chip to a steel flat surface is described. The method is based on adhesive bonding of the silicon chip rear surface on steel using two types of glue normally used for standard piezoresistive strain sensors (Mbond200/ 600), using direct wire bonding of the chip to a Printed Circuit Board, also fixed on steel. In order to protect the sensor from the external environment, and to improve the MEMS performance, the silicon chip is encapsulated with a metal cap hermetically sealed-off under vacuum condition with a vacuum adhesive in which the bonding wires are also protected from possible damage. In order to evaluate the mechanical coupling of the silicon chip with the bar and thestress transfer extent to the silicon surface, commercial strain sensors have been applied on the chip glued on a steel bar in alaboratory setup able to generate strain by inflection, yielding a stress transfer around 70% from steel to silicon. © 2008 IEEE.

Laminar to turbulent flow transition measurements using an array of SOI-CMOS MEMS wall shear stress sensors

The successful utilization of an array of silicon on insulator complementary metal oxide semiconductor (SOICMOS) micro thermal shear stress sensors for flow measurements at macro-scale is demonstrated. The sensors use CMOS aluminum metallization as the sensing material and are embedded in low thermal conductivity silicon oxide membranes. They have been fabricated using a commercial 1 μm SOI-CMOS process and a post-CMOS DRIE back etch. The sensors with two different sizes were evaluated. The small sensors (18.5 ×18.5 μm2 sensing area on 266 × 266 μm2 oxide membrane) have an ultra low power (100 °C temperature rise at 6mW) and a small time constant of only 5.46 μs which corresponds to a cut-off frequency of 122 kHz. The large sensors (130 × 130 μm2 sensing area on 500 × 500 μm2 membrane) have a time constant of 9.82 μs (cut-off frequency of 67.9 kHz). The sensors' performance has proven to be robust under transonic and supersonic flow conditions. Also, they have successfully identified laminar, separated, transitional and turbulent boundary layers in a low speed flow. © 2008 IEEE.

Flexible array sensors based on zinc oxide nanowires for touch displays

Recent efforts towards the fabrication of touch sensing systems are presented, in which zinc oxide nanowire arrays are embedded in a polymer matrix to produce an engineered composite material. In the future, these sensor systems will be fully flexible and multi-touch as intended for Nokia's 'Morph' concept device.

Thermal characterization of SOI CMOS micro hot-plate gas sensors

This work reports on thermal characterization of SOI (silicon on insulator) CMOS (complementary metal oxide semiconductor) MEMS (micro electro mechanical system) gas sensors using a thermoreflectance (TR) thermography system. The sensors were fabricated in a CMOS foundry and the micro hot-plate structures were created by back-etching the CMOS processed wafers in a MEMS foundry using DRIE (deep reactive ion etch) process. The calibration and experimental details of the thermoreflectance based thermal imaging setup, used for these micro hot-plate gas sensor structures, are presented. Experimentally determined temperature of a micro hot-plate sensor, using TR thermography and built-in silicon resistive temperature sensor, is compared with that estimated using numerical simulations. The results confirm that TR based thermal imaging technique can be used to determine surface temperature of CMOS MEMS devices with a high accuracy. © 2010 EDA Publishing/THERMINIC.

Effect of benzocaine on opercular movement and oxygen consumption in Channa punctatus (Bloch)

Effect of anaesthetization with benzocaine at the rate of 18.0 mg.1super(-1) on juveniles of Channa punctatus was observed using a cylindrical glass respirometer. Oxygen consumption and opercular movement were studied at 3h and 24h of anaesthetization. The oxygen consumption of control fish increased linearly from 0.183±0.029 to 0.481±0.034 mlO sub(2).h super(-1) with an increase in body weight from 1.45±0.18 to 6.12±0.11g and showed a reduction (p<0.001) of about 41% in 3h and 37% in 24h anaesthetization of Benzocaine. Similarly, the opercular movement of control fish ranging between 46±1 to 49±1min super(-1) came down to show a reduction (p<0.001) of 43% and 38% respectively in 3h and 24h anaesthetization. The information is useful in calculation of oxygen requirement of this species for live transportation and other experimental purpose.

Fabrication and testing of a high resolution extensometer based on resonant MEMS strain sensors

A novel type of linear extensometer with exceptionally high resolution of 4 nm based on MEMS resonant strain sensors bonded on steel and operating in a vacuum package is presented. The tool is implemented by means of a steel thin bar that can be pre-stressed in tension within two fixing anchors. The extension of the bar is detected by using two vacuum-packaged resonant MEMS double- ended tuning fork (DETF) sensors bonded on the bar with epoxy glue, one of which is utilized for temperature compensation. Both sensors are driven by a closed loop self-oscillating transresistance amplifier feedback scheme implemented on a PCB (Printed Circuit Board). On the same board, a microcontroller-based frequency measurement circuit is also implemented, which is able to count the square wave fronts of the MEMS oscillator output with a resolution of 20 nsec. The system provides a frequency noise of 0.2 Hz corresponding to an extension resolution of 4 nm for the extensometer. Nearly perfect temperature compensation of the frequency output is achieved in the temperature range 20-35 C using the reference sensor. © 2011 IEEE.

Impedance control is tuned to multiple directions of movement

Humans are able to learn tool-handling tasks, such as carving, demonstrating their competency to make and vary the direction of movements in unstable environments. It has been shown that when a single reaching movement is repeated in unstable dynamics, the central nervous system (CNS) learns an impedance internal model to compensate for the environment instability. However, there is still no explanation for how humans can learn to move in various directions in such environments. In this study, we investigated whether and how humans compensate for instability while learning two different reaching movements simultaneously. Results show that when performing movements in two different directions, separated by a 35° angle, the CNS was able to compensate for the unstable dynamics. After adaptation, the force was found to be similar to the free movement condition, but stiffness increased in the direction of instability, specifically for each direction of movement. Our findings suggest that the CNS either learned an internal model generalizing over different movements, or alternatively that it was able to switch between specific models acquired simultaneously. © 2008 IEEE.

Effects of water movement and aeration system on the survival and growth of hatchery bred sugpo (Penaeus monodon Fabricius) in earthen nursery ponds

An experiment was conducted to determine the effects of water movement and airlift aeration on the survival and growth of P. monodon fry reared from P sub(4)P sub(5) to P sub(32)P sub(33) in earthen brackishwater ponds. The high survival rates obtained justify the need for aeration when using the earliest stages of fry (P sub(4)P sub(5)) at higher stocking densities. For older stages regardless of source and at lower stocking densities, nursery operations based on traditional methods could also achieve better survival rates.

Results of drift card experiments and considerations on the movement of milkfish eggs and larvae in the northern Sulu Sea

For a period of one year beginning December 1977, drift card experiments were conducted off the western and southern coasts of Panay Island to determine the surface currents in the area. Of a total 2,384 drift cards released during the study, 382 (16.02%) were recovered, 92% of them within 30 days following dispatch. The surface currents in the study area are strongly influenced, in direction and speed, by the prevailing monsoon winds. During the NE monsoon period, the surface currents move away from the coast; during the SW monsoon, toward and/or parallel to the coast. Based on the results, the probable movement and transport of milkfish (Chanos chanos) eggs and larvae from the spawning ground to the fry collection ground are also discussed.

Spatially directed movement and neuronal activity in freely moving monkey

The abilities to plan a series of movements and to navigate within the environment require the functions of the frontal and ventromedial temporal lobes, respectively. Neuropsychological studies posit the existence of egocentric (prefrontal) and allocentri

Our mother ocean: enclosure, commons, and the global fishermen's movement [book review]

The book is written by Mariarosa Dalla Costa and Monica Chilese; translated by Silvia Federici; Common Notions; NY.2014. It is a vigorous critique of where globalization and industrialization in fishing have led global water resources to, and the direct role that humankind has played in this destructive relationship.

Impedance control is selectively tuned to multiple directions of movement

Humans are able to learn tool-handling tasks, such as carving, demonstrating their competency to make movements in unstable environments with varied directions. When faced with a single direction of instability, humans learn to selectively co-contract their arm muscles tuning the mechanical stiffness of the limb end point to stabilize movements. This study examines, for the first time, subjects simultaneously adapting to two distinct directions of instability, a situation that may typically occur when using tools. Subjects learned to perform reaching movements in two directions, each of which had lateral instability requiring control of impedance. The subjects were able to adapt to these unstable interactions and switch between movements in the two directions; they did so by learning to selectively control the end-point stiffness counteracting the environmental instability without superfluous stiffness in other directions. This finding demonstrates that the central nervous system can simultaneously tune the mechanical impedance of the limbs to multiple movements by learning movement-specific solutions. Furthermore, it suggests that the impedance controller learns as a function of the state of the arm rather than a general strategy. © 2011 the American Physiological Society.