Influence of gate dielectrics on charge transport in copper phthalocyanine thin-film transistors

Copper phthalocyanine organic thin-film transistors (OTFTs) were fabricated with top-gate geometry and the effects of different gate dielectrics on the transport proper-ties in OTFTs were studied. The mobility was found to be gate voltage dependent and the results showed that besides the charge density in the accumulation layer, the energetic disorder induced by gate dielectrics played an important role in determining the field-effect mobility in OTFTs.

Fabrication of an integrated pixel with an organic light-emitting diode driven by copper phthalocyanine organic thin film transistors

An organic integrated pixel with organic light-emitting diodes (OLEDs) driven by organic thin film transistors (OTFTs) is fabricated by a greatly simplified processing. The OTFTs are based on copper phthalocyanine as the active medium and fabricated on indium-tin-oxide (ITO) glass with top-gate structure, thus an organic integrated pixel is easily made by integrating OLED with OTFT. The OTFTs show field-effect mobility of 0.4 cm(2) /Vs and on/off ratio of 10(3) order. The OLED is driven well and emits the brightness as large as 2100cd/m(2) at a current density of 14.6 mu A/cm(2) at -19.7 V gate voltage. This simple device structure is promising in the future large-area flexible OLED displays.

Carbon nanotube/gold nanoparticles/polyethylenimine-functionalized ionic liquid thin film composites for glucose biosensing

A novel glucose biosensor based on immobilization of glucose oxidase (GOD) in thin films of polyethylenimine-functionalized ionic liquid (PFIL), containing a mixture of carbon nanotubes (CNT) and gold nanoparticles (AuNPs) and deposited on glassy carbon electrodes, was developed. Direct electrochemistry of glucose oxidase in the film was observed, with linear glucose response up to 12 mM. The PFIL-stabilized gold nanoparticles had a diameter of 2.4 +/- 0.8 nm and exhibited favorable stability (stored even over one month with invisible change in UV-vis spectroscopic measurements).

Single-crystal-like organic heterojunction with 40 nm thick charge accumulation layers

Single-crystal-like organic heterojunction films of copper phthalocyanine (CuPc) and copper-hexadecafluoro-phthalocyanine (F16CuPc) were fabricated by weak-epitaxy-growth method. The intrinsic properties of organic heterojunction were revealed through threshold voltage shift of field-effect transistors and measurement of single-crystal-like diodes. At both sides of the heterojunction interface 40 nm thick charge accumulation layers formed, which showed that the long carriers' diffusion length is due to the high crystallinity and low density of deep bulk traps of single-crystal-like films.

Surface potential images of polycrystalline organic semiconductors obtained by Kelvin probe force microscopy

P-type copper phthalocyanine (CuPc) and n-type hexadecafluorophthalocyanina-tocopper (F16CuPc) polycrystalline films were investigated by Kelvin probe force microscopy (KPFM). Topographic and corresponding surface potential images are obtained simultaneously. Surface potential images are related with the local work function of crystalline facets and potential barriers at the grain boundaries (GBs) in organic semiconductors. Based on the spatial distribution of surface potential at GBs, donor- and acceptor-like trapping states in the grain boundaries (GBs) of p-CuPc and n-F16CuPc films are confirmed respectively.

Weak Epitaxy Growth of Copper Hexadecafluorophthalocyanine (F16CuPc) on p-Sexiphenyl Monolayer Film

Weak epitaxy growth (WEG) behavior and mechanism of copper hexadecafluorophthalocyanine (F16CuPc) on p-sexiphenyl (p-6P) monolayer film were investigated by atomic force microscopy (AFM), selected area electron diffraction (SEAD), and wide-angle X-ray diffraction (WAXD). High-quality F16CuPc films with high order, large size, and molecular-level smoothness were obtained successfully by WEG method. It was identified that there exists incommensurate epitaxial relation between highly oriented F16CuPc and p-6P films. The geometrical channels of p-6P monolayer surface induce the nucleation and growth of F16CuPc molecules.

Synthesis and Characterizations of Poly(9,10-bisarylethynyl-2,6-anthrylene)s and Poly(9,10-bisalkynyl-2,6-anthrylene)

A poly(9,10-bisalkynyl-2,6-anthrylene) (PI) and five poly(9,10-bisarylethynyl-2,6-anthrylene)s(P2-P6) as soluble conjugated polymers have been synthesized and characterized. All polymers exhibit two-dimensional conjugated characteristics as indicated by absorption spectra comprising multi-bands in the range of 300-600 nm. Compared with P1, polymers P2-P5, which contain phenylethynyl substituents with the longer conjugation than alkynyl groups, exhibit a similar to 60 nm red shift of absorption edge. However, further increasing the conjugation length of the arylethynyl substituents (longer than phenylethynyl) has only a no effect on the conjugation of the polymer chains, while comparing the absorption spectra of P6 with those of P2-P5.

Poly(oligothiophene-alt-benzothiadiazole)s: Tuning the Structures of Oligothlophene Units toward High-Mobility "Black" Conjugated Polymers

A series of donor-acceptor low-bandgap conjugated polymers, i.e., PTnBT (n = 2-6), composed of alternating oligothiophene (OTh) and 2,1,3-benzothiadiazole (BT) units were synthesized by Stille cross-coupling polymerization. The number of thiophene rings in OTh units, that is n, was tuned from 2 to 6. All these polymers display two absorption bands in both solutions and films with absorption maxima depending on n. From solution to film, absorption spectra of the polymers exhibit a noticeable red shift. Both high- and low-energy absorption bands or P'F5BT and PT6BT films locate in the visible region, which are at 468 and 662 nm for PT5BT and 494 and 657 nm for PT6BT.

Synthesis and Characterization of Coil-Rod-Coil Triblock Copolymers Comprising Fluorene-Based Mesogenic Monodisperse Conjugated Rod and Poly(ethylene oxide) Coil

A series of coil-rod-coil triblock copolymers (i.e., F3T8EO8, F3T8EO17, F3T8EO45, and F3T8EO125) with a mesogenic monodisperse conjugated oligomer comprising 3 fluorene, 8 thiophene, and 2 phenyl units as the rod and poly(ethylene oxide) (PEO) as the coil were synthesized. A reference compound, that is F3T8ME2, with the identical rod but without PEO was also prepared for comparison. The volume fraction of PEO (f(PEO)) was 0, 0.16, 0.28, 0.50, and 0.73 for F3T8ME2, F3T8EO8, F3T8EO17, F3T8EO45, and F3T8EO125, respectively. It was found that the introduction of PEO into the triblock copolymers encouraged the formation of H-type aggregation and f(PEO)-dependent highly ordered mesophases while f(PEO) < 0.73. For F3T8ME2, only nematic mesophase was observed. In contrast, F3T8EO8 and F3T8EO17, with f(PEO) of 0.16 and 0.28, respectively, are smectic A (SA) mesomorphism.

Constructing Thin Polythiophene Film Composed of Aligned Lamellae via Controlled Solvent Vapor Treatment

Thin poly(3-butylthiophene) (P3BT) film composed of aligned lamellae attached to the edge of the original film has been achieved via a controlled solvent vapor treatment (C-SVT) method. The polarized optical microscopy operated at both single-polarization and cross-polarization modes has been used to investigate the alignment of the fiber-like lamellae. A numerical simulation method is used to quantitatively calculate angle distributions of the lamellae deviated from the film growth direction. Prepatterned P3BT film edge acts as nuclei which densely initialize subsequent crystal growth by exhausting the materials transported from the partially dissolved film. The growth of new film upon crystallization is actually a self-healing process where the two-dimensional geometric confinement is mainly responsible for this parallel alignment of P3BT crystals. The solvent vapor pressure should be carefully chosen so as to induce crystal growth but avoid liquid instability which will destroy the continuity of the film.

Hydrothermal Synthesis and Luminescent Properties of Novel Ordered Sphere CePO4 Hierarchical Architectures

The ordered-sphere CePO4 hierarchical architectures have been successfully synthesized by a simple hydrothermal method through the controlled growth of the CePO4 nanorods and self-assemble hierarchical structure under various reaction conditions. The evolution of the morphology of the samples has been investigated in detail. It was found that the coexistence of citric acid and cetaltrimethylammonium bromide in the reaction system plays an important role in the formation of the spherical CePO4 hierarchical architectures. A possible mechanism of the formation and growth of the hierarchical structure was suggested according to the experimental results and analysis. The effects of the reaction time as well as the variation of the morphologies on the luminescent properties of the products were also studied.

Bilayer Photoresist Insulator for High Performance Organic Thin-Film Transistors on Plastic Films

A novel bilayer photoresist insulator is applied in flexible vanadyl-phthalocyanine (VOPc) organic thin-film transistors (OTFTs). The micron-size patterns of this photoresisit insulator can be directly defined only by photolithography without the etching process. Furthermore, these OTFTs exhibit high field-effect mobility (about 0.8 cm(2)/Vs) and current on/off ratio (about 10(6)). In particular, they show rather low hysteresis (< 1 V). The results demonstrate that this bilayer photoresist insulator can be applied in large-area electronics and in the facilitation of patterning insulators.

Achieving perpendicular alignment of rigid polythiophene backbones to the substrate by using solvent-vapor treatment

The rigid backbone of the poly(3-butylthiophene) molecule adopts a perpendicular orientation with respect to the substrate by using a solvent-vapor treatment (see figure). Small and closely contacting spherulites instead of conventional whisker-like crystals are achieved. This could be utilized to improve charge-carrier mobility particularly in the direction normal to the film plane by designing and constructing thick crystalline domains in the functional layer.

Synthesis and characterization of monodisperse oligo(fluorene-co-bithiophene)s

A series of monodisperse oligo(9,9-di-n-octylfluorene-co-bithiophene)s (OFbTs) with molecular lengths of up to 19.5 nm and molecular weights up to 7025 g mol(-1) has been synthesized by a divergent/convergent approach involving Stille coupling reactions. Stille coupling is quite efficient in preparing this class of oligomers, and even the molecule with nine fluorene units and eight bithiophene units (F9Th16) can be synthesized in a yield as high as 70%. Because of easy functionalization of the thiophene ring at its alpha position, no additional protecting group allowing activation for further reaction is necessary. However, the synthetic routes must be optimized to eliminate contamination of the targeting compounds with the homocoupling product of the organotin reagents. Synthesis of the longest oligomer F13Th24 in a relative large quantity is limited by its low yield due to the pronounced ligand-exchange side reactions of the starting materials and reaction intermediates. All oligomers longer than F4Th6 are nematic mesomorphs and exhibit enhanced glass transition temperature and clearing point with increasing molecular length, as revealed by differential scanning calorimetry and polarizing optical microscopy.