Daily photosynthesis, water relations, and ion concentrations of uuonymus irrigated with treated wastewater

Euonymus japonica Thunb. (euonymus) plants were submitted for 9 months to two irrigation treatments using water from different sources: a control (C) water with electrical conductivity (EC) less than 1.2 dS.m(-1) and reclaimed wastewater (RW) with EC approximate to 4 dS.m(-1). At the end of the experiment, no differences in the total dry weight were observed between treatments, whereas the leaf dry mass increased (to the detriment of the root part in RW plants). Throughout the day, the stem water potential (Psi(stem)) of the RW plants was lower than in C, whereas stomatal conductance (g(S)) was slightly reduced in RW from 0800 HR to 1200 HR, but no significant variation in photosynthesis (P-n) or energy conversion efficiency (F'(v)/F'(m)) in photosystem II was detected through the effect of salinity. Gas exchange and fluorescence showed a tendency to increase after midday in plants treated with RW. The photosynthetic behavior and fluorescence of RW plants may have been related to the nitrogen and chlorophyll content of the leaves, confirming the resistance of the photosynthetic mechanism to salinity in this species in these conditions. The toxic effects produced by high concentrations of boron (B), sodium (Na+) and chloride (Cl-) were offset by the effect of other ions like magnesium (Mg2+), potassium (K+), and phosphorus (P) in plants irrigated with RW, thus improving their physiological status without decreasing their ornamental value.

BIOMECHANICAL BEHAVIOR OF THE SYSTEM PROSTHESIS/DENTAL IMPLANT: ANALYSIS BY THE PHOTOELASTICITY METHOD

One of the main reasons for the failure in dental implant treatments is the overload, which can cause bone resorption and later, the osseointegration loss in the implant. Therefore, the aim of this study was to analyze the tension generated around dental implants in the rehabilitation of three mandible posterior teeth, varying the connection type, the disposal, and the quantity of implants. The photoelasticity method was used in order to accomplish it. Through photoelasticity, the quantity and localization of the tensions around the implants in the different studied groups were compared (three straight line implants, three offset placement implants, two implants with a mesial cantilever, and two implants with a pontic). The results showed that the tension quantity and disposition around the dental implants of the connection external hexagon and internal hexagon were similar in all groups. In the group where the cantilever was used, an increase of the tension around the implant, adjacent to the cantilever, was observed. From the results it is concluded that the type of connection used in this study did not influence the tension quantity and distribution around the implants; however, the prosthetic configuration with the cantilever use, led to an increase of the tension around the implant, adjacent to the cantilever.

Utilização da instrumentação virtual em Labview para criação da interface gráfica do amplificador lock-in utilizado em estudos fisiológicos a partir da comunicação via porta serial

This work presents the development of a graphical interface to the Lock-in Amplifier, which is used in physiological studies on the motility of the gastrointestinal tract in rats and signal processing. With a simple and low cost instrumentation, the resources offered by the virtual interface of LabVIEW software allows the creation of commands similar to the actual instrument that, through communication via standard serial port, transmits data between a PC and peripheral device performing specific and particular needs in the amplifier. Created for the lock-in amplifier model SR830 Stanford Research Systems, the remote manipulation gives the user greater accessibility in the process of configuration and calibration. And, since the software is installed, there is the advantage of eliminating the need of purchase new devices to upgrade the system. The commands created were made to perform six basic modifications that are used in routine of the Biomagnetism Laboratory. The instrumentation developed has the following controls: Amplitude, Frequency, Time Constant, slope low pass filter, sensitivity and offset

Physical and chemical matrix effects in soil carbon quantification using laser-induced breakdown spectroscopy

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Padrões de movimentação de sabiás (Turdus ssp. Turdidae) em paisagens fragmentadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise das tensões em próteses implantossuportadas esplintadas, variando a localização dos implantes, pôntico e cantilever: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Greenhouse gas balance in the conversion from extensive pasture to other agricultural systems in Andean region of Colombia

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Tratamento térmico de filmes supercondutores do sistema BSCCO utilizando forno de micro-ondas doméstico

Pós-graduação em Ciência dos Materiais - FEIS

DFT + U Simulation of the Ti4O7-TiO2 Interface

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adrenomedullin induces pulmonary vasodilation but does not attenuate pulmonary hypertension in a sheep model of acute pulmonary embolism

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeitos da adrenomodulina no tratamento da hipertensão pulmonar induzida por microesferas em ovinos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Greenhouse gas balance associated with sugarcane production in South-Central Brazil, considering the management and expansion

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Qualidade da madeira de árvores de guapuruvu (schizolobium parahyba (vell.) blake) com 15 anos provenientes de área de recuperação florestal

Pós-graduação em Ciência Florestal - FCA

Conversor analógico digital de 10 bits utilizando arquitetura pipeline e tecnologia CMOS

Pós-graduação em Engenharia Elétrica - FEIS

Modelos geoidais híbridos para o Estado de São Paulo: desenvolvimento e avaliação

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)