Dendritic Arm Spacing Affecting Mechanical Properties and Wear Behavior of Al-Sn and Al-Si Alloys Directionally Solidified under Unsteady-State Conditions

Alloys of Al-Sn and Al-Si are widely used in tribological applications such as cylinder liners and journal bearings. Studies of the influence of the as-cast microstructures of these alloys on the final mechanical properties and wear resistance can be very useful for planning solidification conditions in order to permit a desired level of final properties to be achieved. The aim of the present study was to contribute to a better understanding about the relationship between the scale of the dendritic network and the corresponding mechanical properties and wear behavior. The Al-Sn (15 and 20 wt pct Sn) and Al-Si (3 and 5 wt pct Si) alloys were directionally solidified under unsteady-state heat flow conditions in water-cooled molds in order to permit samples with a wide range of dendritic spacings to be obtained. These samples were subjected to tensile and wear tests, and experimental quantitative expressions correlating the ultimate tensile strength (UTS), yield tensile strength, elongation, and wear volume to the primary dendritic arm spacing (DAS) have been determined. The wear resistance was shown to be significantly affected by the scale of primary dendrite arm spacing. For Al-Si alloys, the refinement of the dendritic array improved the wear resistance, while for the Al-Sn alloys, an opposite effect was observed, i.e., the increase in primary dendrite arm spacing improved the wear resistance. The effect of inverse segregation, which is observed for Al-Sn alloys, on the wear resistance is also discussed.

Corrosion resistant and adsorbent plasma polymerized thin film

Adsorbent and corrosion resistant films are useful for sensor development. Therefore, the aim of this work is the production and characterization of plasma polymerized fluorinated organic ether thin films for sensor development. The polymerized reactant was methyl nonafluoro(iso)butyl ether. Infrared Spectroscopy showed fluorinated species and eventually CO but CH(n) is a minor species. Contact angle measurements indicated that the film is hydrophobic and organophilic but oleophobic. Optical microscopy reveals not only a good adherence on metals and acrylic but also resistance for organic solvents, acid and basic aqueous solution exposure. Double layer and intermixing are possible and might lead to island formation. Quartz Crystal Microbalance showed that 2-propanol permeates the film but there is no sensitivity to n-hexane. The microreactor manufactured using a 73 cm long microchannel can retain approximately 9 X 10(-4) g/cm(2) of 2-propanol in vapor phase. Therefore, the film is a good candidate for preconcentration of volatile organic compounds even in corrosive environment. (C) 2009 Elsevier B.V. All rights reserved.

Does habitat modification affect oviposition by the salt marsh mosquito, Ochlerotatus vigilax (Skuse) (Diptera : Culicidae)?

Studies were conducted at sites in south-cast Queensland, Australia, to investigate the effect of habitat modification for mosquito control on the distribution of eggshells of the salt marsh mosquito, Ochlerotatus vigilax (Skuse). Modifications were mainly tunnelling, but an Open Marsh Water Management (OMWM) site and a grid-ditched site were also included. There were two separate experimental designs: one was data collected Before and After (BA) modification and the other was for other sites with a Treatment and Control (TC) experimental design. For the BA data, there were significant reductions in eggshells after modification. Eggshells were generally fewer after modification in areas which were close to unrestricted tidal flushing. A sandy substrate and vegetation changes which resulted in reduced Sporobolus virginicus or mixed Sporobolus and Sarcocornia quinqueflora also contributed to the effect. In the TC experiment, there was no effect of modification at the tunnelled site, eggshells were fewer at the OMWM site, but there were more eggshells at the grid-ditched site. There was some general indication that recent oviposition activity was reduced in sites that had been modified, evidenced by a relatively small proportion of young (dark coloured) eggshells.

Phase and microstructural evolution during the heat treatment of Sm-Ca-alpha-sialon ceramics

The phase and microstructural evolution of multi-cation Sm-Ca-alpha-sialon ceramics was investigated. Six samples were prepared, ranging from a pure Sm-sialon to a pure Ca-sialon, with calcium replacing samarium in 20 eq% increments, thus maintaining an equivalent design composition in all samples. After pressureless sintering at 1820 degreesC for 2 It, all samples were subsequently heat treated up to 192 h at 1450 and 1300 degreesC. The amount of grain boundary glass in the samples after sintering was observed to decrease with increasing calcium levels. A M-ss' or M-ss',-gehlenite solid solution was observed to form during the 1450 degreesC heat treatment of all Sm-containing samples, and this phase forms in clusters in the high-Sm samples. The thermal stability of the alpha-sialon phase was improved in the multi-cation systems. Heat treatment at 1300 degreesC produces SmAlO3 in the high-Sm samples, a M-ss',-gehlenite solid solution in the high-Ca samples, and a Sm-Ca-apatite phase in some intermediate samples. (C) 2002 Elsevier Science Ltd. All rights reserved.

Predicting sheetwash and rill erosion over the Australian continent

Soil erosion is a major environmental issue in Australia. It reduces land productivity and has off-site effects of decreased water quality. Broad-scale spatially distributed soil erosion estimation is essential for prioritising erosion control programs and as a component of broader assessments of natural resource condition. This paper describes spatial modelling methods and results that predict sheetwash and rill erosion over the Australian continent using the revised universal soil loss equation (RUSLE) and spatial data layers for each of the contributing environmental factors. The RUSLE has been used before in this way but here we advance the quality of estimation. We use time series of remote sensing imagery and daily rainfall to incorporate the effects of seasonally varying cover and rainfall intensity, and use new digital maps of soil and terrain properties. The results are compared with a compilation of Australian erosion plot data, revealing an acceptable consistency between predictions and observations. The modelling results show that: (1) the northern part of Australia has greater erosion potential than the south; (2) erosion potential differs significantly between summer and winter; (3) the average erosion rate is 4.1 t/ha. year over the continent and about 2.9 x 10(9) tonnes of soil is moved annually which represents 3.9% of global soil erosion from 5% of world land area; and (4) the erosion rate has increased from 4 to 33 times on average for agricultural lands compared with most natural vegetated lands.

Surgical planning for resection of an ameloblastoma and reconstruction of the mandible using a selective laser sintering 3D biomodel

Ameloblastoma is a benign locally aggressive infiltrative odontogenic lesion. It is characterized by slow growth and painless swelling. The treatment for ameloblastoma varies from curettage to en bloc resection, and the reported recurrence rates after treatment are high; the safety margin of resection is important to avoid recurrence. Advances in technology brought about great benefits in dentistry; a new generation of computed tomography scanners and 3-dimensional images enhance the surgical planning and management of maxillofacial tumors. The development of new prototyping systems provides accurate 3D biomodels on which surgery can be simulated, especially in cases of ameloblastoma, in which the safety margin is important for treatment success. A case of mandibular follicular ameloblastoma is reported where a 3D biomodel was used before and during surgery.

Research commentary: Information systems and conceptual modeling - A research agenda

Within the information systems field, the task of conceptual modeling involves building a representation of selected phenomena in some domain. High-quality conceptual-modeling work is important because it facilitates early detection and correction of system development errors. It also plays an increasingly important role in activities like business process reengineering and documentation of best-practice data and process models in enterprise resource planning systems. Yet little research has been undertaken on many aspects of conceptual modeling. In this paper, we propose a framework to motivate research that addresses the following fundamental question: How can we model the world to better facilitate our developing, implementing, using, and maintaining more valuable information systems? The framework comprises four elements: conceptual-modeling grammars, conceptual-modeling methods, conceptual-modeling scripts, and conceptual-modeling contexts. We provide examples of the types of research that have already been undertaken on each element and illustrate research opportunities that exist.

Perfil dos pacientes revascularizados do miocárdio no período de 2004 a 2008 em um Hospital Universitário do Espírito Santo

Objetivo: Caracterizar os pacientes submetidos à Revascularização do miocárdio (RM); descrever o perfil clínico dos pacientes submetidos a RM e descrever o fluxo intra e extra hospitalar no perioperatório desses pacientes. Métodos: Foi realizado um estudo descritivo analítico de dados secundários de 147 prontuários de pacientes submetidos a RM em Hospital de ensino, Vitória, Espírito Santo, Brasil, no período entre 2004 a 2008. Para a análise dos dados foi realizado o método descritivo. Resultados: A pesquisa apontou como perfil de maior incidência para RM a predominância do sexo masculino, com faixa etária entre 50 e 69, a maioria dos pacientes tinha de uma a duas doenças associadas. Ocorrência de óbito em 11,6%. O fluxo intra-hospitalar apresentou um tempo total de espera entre o CATE (cateterismo cardíaco) e a RM com mediana de 55 dias; Houve suspensão da RM por problemas relacionados à estrutura e administração e ao paciente. O motivo mais freqüente relacionada à estrutura foi a falta de leitos no Centro de Tratamento Intensivo (CTI). Conclusão: Percebeu-se que a análise das variáveis clínicas propostas apontou para resultados compatíveis com o panorama nacional nesta área. Contudo no aspecto da trajetória foi identificada a influência de questões relacionadas à gestão de recursos humanos e de estrutura para o desenvolvimento das atividades hospitalares, tendo como resultado, a dificuldade de atendimento da demanda pela capacidade instalada, assim como a fragmentação de atividades relacionadas ao planejamento assistencial, de registros e da organização dos prontuários. Com o estudo dessas variáveis foi possível a construção de uma ficha para a coleta de dados em RM, de forma que estes oferecem subsídios para a implantação de banco de dados construído pela autora e para a implementação de ações interdisciplinares no serviço de cirurgia cardíaca do local de estudo.

Moravia : das lógicas da informalidade às lógicas da formalidade

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Arquitetura e Urbanismo, Programa de Pós-Graduação em Arquitetura e Urbanismo, 2016.