Experimental Investigation on Propane Hydrate Dissociation by High Concentration Methanol and Ethylene Glycol Solution Injection

The dissociation behaviors of propane hydrate by high concentration alcohols inhibitors injection were investigated. Methanol (30.0, 60.1, 80.2, and 99.5 wt %) and ethylene glycol (30.0, 60.1, 69.8, 80.2, and 99.5 wt %) solution were injected, respectively, as alcohols inhibitors in 3.5 L transparent reactor. It is shown that the average dissociation rates of propane hydrate injecting methanol and ethylene glycol solution are 0.02059-0.04535 and 0.0302-0.0606 mol.min(-1).L-1, respectively. The average dissociation rates increase with the mass concentration increase of alcohols solution, and it is the biggest when 99.5 wt % ethylene glycol solution was injected. The presence of alcohols accelerates gas hydrate dissociation and reduces the total need of external energy to dissociate the hydrates. Density differences act as driving force, causing the acceleration effects of ethylene glycol on dissociation behaviors of propane hydrate are better than that of methanol with the same injecting flux and mass concentration.

Synthesis Gas Generation by Chemical-Looping Reforming Using Ce-Based Oxygen Carriers Modified with Fe, Cu, and Mn Oxides

Chemical-looping reforming (CLR) is a technology that can be used for partial oxidation and steam reforming of hydrocarbon fuels. It involves the use of a metal oxide as an oxygen carrier, which transfers oxygen from combustion air to the fuel. Composite oxygen carriers of cerium oxide added with Fe, Cu, and Mn oxides were prepared by co-precipitation and investigated in a thermogravimetric analyzer and a fixed-bed reactor using methane as fuel and air as oxidizing gas. It was revealed that the addition of transition-metal oxides into cerium oxide can improve the reactivity of the Ce-based oxygen carrier. The three kinds of mixed oxides showed high CO and H-2 selectivity at above 800 degrees C. As for the Ce-Fe-O oxygen carrier, methane was converted to synthesis gas at a H-2/CO molar ratio close to 2:1 at a temperature of 800-900 degrees C; however, the methane thermolysis reaction was found on Ce-Cu-O and Ce-Mn-O oxygen carriers at 850-900 degrees C. Among the three kinds of oxygen carriers, Ce-Fe-O presented the best performance for methane CLR. On Ce-Fe-O oxygen carriers, the CO and H-2 selectivity decreased as the Fe content increased in the carrier particles. An optimal range of the Ce/Fe molar ratio is Ce/Fe > 1 for Ce-Fe-O oxygen carriers. Scanning electron microscopy (SEM) analysis revealed that the microstructure of the Ce-Fe-O oxides was not dramatically changed before and after 20 cyclic reactions. A small amount of Fe3C was found in the reacted Ce-Fe-O oxides by X-ray diffraction (XRD) analysis.

Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Replacement of methane from quartz sand-bearing hydrate with carbon dioxide-in-water emulsion

The replacement of CH4 from its hydrate in quartz sand with 90:10, 70:30, and 50:50 (W-CO2:W-H2O) carbon dioxide-in-water (C/W) emulsions and liquid CO2 has been performed in a cell with size of empty set 36 x 200 mm. The above emulsions were formed in a new emulsifier, in which the temperature and pressure were 285.2 K and 30 MPa, respectively, and the emulsions were stable for 7-12 h. The results of replacing showed that 13.1-27.1%, 14.1-25.5%, and 14.6-24.3% of CH4 had been displaced from its hydrate with the above emulsions after 24-96 It of replacement, corresponding to about 1.5 times the CH4 replaced with high-pressure liquid CO2. The results also showed that the replacement rate of CH4 with the above emulsions and liquid CO2 decreased from 0.543, 0.587, 0.608, and 0.348 1/h to 0.083, 0.077, 0.069, and 0.063 1/h with the replacement time increased from 24 to 96 h. It has been indicated by this study that the use of CO2 emulsions is advantageous compared to the use of liquid CO2 in replacing CH4 from its hydrate.

Heterogeneous catalysts for biodiesel production

The production of biodiesel is greatly increasing due to its enviromental benefits. However, production costs are still rather high, compared to petroleum-based diesel fuel. The introduction of a solid heterogeneous catalyst in biodiesel production could reduce its price, becoming competitive with diesel also from a financial point of view. Therefore, great research efforts have been underway recently to find the right catalysts. This paper will be concerned with reviewing acid and basic heterogeneous catalyst performances for biodiesel production, examining both scientific and patent literature.

Gasoline-range hydrocarbon synthesis over cobalt-based Fischer-Tropsch catalysts supported onSiO2/HZSM-5

Two types of SiO2 with different mesopore size and HZSM-5 zeolite were used to prepare hybrid supported cobalt-based catalysts. The textual and structural properties of the catalysts were studied using N-2 physisorption, X-ray diffraction (XRD), and H-2 temperature-programmed reduction (TPR) techniques. Fischer-Tropsch synthesis (FTS) performances of the catalysts were carried out in a fixed-bed reactor. The combination effects of the meso- and micropores of the supports as well as the interaction between supports and cobalt particles on FTS activity are discussed. The results indicate that the catalyst supported on the tailor-made SiO2 and HZSM-5 hybrid maintained both meso- and micropore pores during the preparation process without HZSM-5 particles agglomerating. The mesopores provided quick mass transfer channels, while the micropores contributed to high metal dispersion and accelerated hydrocracking/hydroisomerization reaction rate. High CO conversion of 83.9% and selectivity to gasoline-range hydrocarbons (C-5-C-12) of 55%, including more than 10% isoparaffins, were achieved simultaneously on this type of catalyst.

Experimental investigation of production behavior of methane hydrate under ethylene glycol injection in unconsolidated sediment

This article investigates the gas production behavior from methane hydrate (MH) in porous sediment by injecting ethylene glycol (EG) solution with the different concentrations and the different injection rates in an one-dimensional experimental apparatus. The results suggest that the gas production process can be divided into the four stages: (1) the initial injection, (2) the EG diluteness, (3) the hydrate dissociation, and (4) the remained gas output. Nevertheless, the water production rate keeps nearly constant during the whole production process. The production efficiency is affected by both the EG concentration and the EG injection rate, and it reaches a maximum with the EG concentration of 60 wt %.

Upgrading bio-oil over different solid catalysts

Solid acid 40SiO(2)/TiO2-SO42- and solid base 30K(2)CO(3)/Al2O3-NaOH were prepared and compared with catalytic esterification activity according to the model reaction. Upgrading bio-oil by solid acid and solid base catalysts in the conditioned experiment was investigated, in which dynamic viscosities of bio-oil was lowered markedly, although 8 months of aging did not show much viscosity to improve its fluidity and enhance its stability positively. Even the dehydration by 3A molecular sieve still kept the fluidity well. The density of upgraded bio-oil was reduced from 1.24 to 0.96 kg/m(3), and the gross calorific value increased by 50.7 and 51.8%, respectively. The acidity of upgraded bio-oil was alleviated by the solid base catalyst but intensified by the solid acid catalyst for its strong acidification. The results of gas chromatography-mass spectrometry analysis showed that the ester reaction in the bio-oil was promoted by both solid acid and solid base catalysts and that the solid acid catalyst converted volatile and nonvolatile organic acids into esters and raised their amount by 20-fold. Besides the catalytic esterification, the solid acid catalyst carried out the carbonyl addition of alcohol to acetals. Some components of bio-oil undertook the isomerization over the solid base catalyst.

Control mechanisms for gas hydrate production by depressurization in different scale hydrate reservoirs

The methane hydrate was formed in a pressure vessel 38 mm in id and 500 mm in length. Experimental works on gas production from the hydrate-bearing core by depressurization to 0.1, 0.93, and 1.93 MPa have been carried out. The hydrate reservoir simulator TOUGH-Fx/Hydrate was used to simulate the experimental gas production behavior, and the intrinsic hydration dissociation constant (K-0) fitted for the experimental data was on the order of 104 mol m(-2) Pa-1 s(-1), which was one order lower than that of the bulk hydrate dissociation. The sensitivity analyses based on the simulator have been carried out, and the results suggested that the hydrate dissociation kinetics had a great effect on the gas production behavior for the laboratory-scale hydrate-bearing core. However for a field-scale hydrate reservoir, the flow ability dominated the gas production behavior and the effect of hydrate dissociation kinetics on the gas production behavior could be neglected.

直接甲醇燃料电池甲醇替代燃料的研究

论文主要研究了直接甲醇燃料电池（DMFC）中三种甲醇替代燃料，二甲氧基甲烷（DMM）、乙醇和乙二醇及导致阳极催化剂中毒的吸附CO（COad）在光滑R电极及几种新的R基催化剂电极上的电氧化行为。结合对催化剂的X射线光电子能谱（xPS）、X衍射(XRD)、扫描电子显微镜（SEM）和热重分析（TG）表征，初步探讨了几种新催化剂对三种甲醇替代燃料的电催化活性要高于碳载R（PtC）催化剂的原因。另外，还研究了用表面活化处理来提高阳极催化剂对甲醇氧化的电催化活性的方法。本论文得到的主要结果如下：1．在研究DMM在不同条件下，在不同R基催化剂电极上的电化学氧化行为的基础上，发现碳载R和TiO2（Pt-TiO2／C）复合催化剂对DMM氧化的电催化活性要优于Pt/C电极。而Pt-TiO2／C催化剂在吸附Ho3+(Pt-TiO2-Ho3+/C)或Eu3＋（Pt-TiO2-Eu3＋/C）后，对DMM氧化的电催化活性比Pt-TiO2／C电极高。表明TiO2、Eu3+和Ho3+对DMM的氧化都有很好的促进作用，这主要是它们都能为DMM的氧化在电极表面提供更多的含氧物种。由于DMM本身在这些催化剂电极上的氧化性能不好，而且DMM容易在酸性溶液中水解，生成甲醇和甲醛，因此，DMM不是一种好的甲醇替代燃料。2．无论在中性介质中还是在酸性介质中，Eu3＋和Ho3＋对乙醇在R／C电极上的电化学氧化反应都有较好的促进作用，而Eu3＋的促进作用要大于H3+，Eu3＋和H3+在酸性溶液中的促进作用要大于在中性溶液中。无论是中性溶液还是酸性溶液中，吸附CO（COad）在Pt／C催化剂电极上在较正的电位处有一个很大的氧化峰，而在R-Eu3＋／C或R-H3＋／C催化剂电极上在较负电位处有两个小的氧化峰，表明吸附的Eu3＋和Ho3+对cood在R／C催化剂电极上的氧化都有很好的促进作用，主要表现在使Cood的吸附强度降低和吸附量减少。XPs测量表明，当R／C电极表面吸附了Eu3＋或H了十后，使催化剂中Pt和c土的电子云密度变小，因此使Pt对coad的吸附强度减弱。由于Eu3＋或H03＋在电极上吸附不是物理吸附，而是化学吸附，因此，它们与Pt的结合具有相对的稳定性。乙醇电氧化的中间产物，如COad等能强烈地吸附在R上，因此会使R中毒。而Eu3＋或H矿"能降低Coad在R上地吸附强度，因此，Eu3＋或H3+能促进乙醇在Pt／C电极上的电化学氧化反应。Pt-TiO2／C催化剂对乙醇氧化的电催化活性要高于R／C催化剂，表明TiO2对乙醇在R／C电极上的电化学氧化反应也有较好的促进作用。XPS的测量表明，TiO2的加入并不改变Pt的电子状态，因此，TiO2能促进乙醇电氧化反应的主要原因是TIOZ能为乙醇氧化提供含氧物种。实验结果表明，Eu3＋或H3+对乙醇在R-TiO2／C电极上的电化学氧化反应也有一定的促进作用。这是由于Eu3＋或H3+改变了R的电子状态，降低了乙醇电氧化中间产物，COod在Pt上的吸附强度，而TIOZ提供了COod的氧化所必须的含氧物种。3．无论是酸性溶液中还是中性溶液中，乙二醇在R-TiO2／C电极上的氧化活性比在R／C电极上高。这表明TIOZ能促进乙二醇在Pt上的电氧化反应。进一步的实验表明，TIOZ对COad在Pt催化剂电极上氧化的促进作用并不明显。XPS测量表明，这是由于TIOZ并不改变R的电子状态。所以，TiO2对乙二醇在Pt上的电氧化的促进作用只是基于提供乙二醇电氧化所需的含氧物种。无论是酸性溶液中还是中性溶液中，乙二醇在R-WO3／C电极上的氧化活性都比在R／C电极上高。这表明W03能促进乙二醇在R上的电氧化反应。进一步的实验表明，R-WO3／C电极对Coad氧化的电催化活性也要高于R／C电极，XPS测量表明，WO3会降低Pt的电子云密度。所以，WO3对乙二醇在R上的电氧化的促进作用除了提供含氧物种外，还由于它能降低R的电子云密度而降低了乙二醇电氧化中间产物。4．用四氢吠喃和丙酮混合溶液浸泡法对电极进行表面处理后能使Pt／C和Pt-WO3／C电极对乙醇和乙二醇氧化的电催化活性有很大的提高。其原因可能是Pt／C和Pt一w03／C电极在经表面处理后，在电极制备过程中带来的表面活性剂等杂质由于溶解在混合溶液中而被除去，Nafion也可能在用混合溶液浸泡后会发生一定程度的结构变化，因此，使活性中心的位点增加，从而增加了催化剂的电催化活性。另外，经表面处理后，Pt／C和Pt-WO3／C电极的活性中心的结构有一定的变化，使COad的吸附强度降低而容易氧化，降低了COad对催化剂的毒化作用，因而提高了电极对乙醇和乙二醇氧化的电催化活性。

The cost estimate for a novel cheap solar cell

The estimate for the lowest cost of SODL (silicon on defect layer) solar cell is made according to the price standard of present market. The estimate shows that the PV (photovoltaics) energy costs can be reduced from today's 25-30 cents/(kW h) to 7-8 cents/(kW h) which is comparable with the present cost of electricity generated by traditional energy sources such as fossil and petroleum fuels. The PV energy costs could be reduced to a value lower than 7-8 cents(kW h) by developing SODL technology. The SODL solar cell manufacture featuring simple processes is suitable to large scale automated assembly lines with high yield of large area cells. Some new ideas are suggested, favoring the further reduction in the cost of commercial solar cells.