Red-Green-Blue 2D tuneable liquid crystal laser devices

In this paper, we review our recent experimental work on coherent and blue phase liquid crystal lasers.We will present results on thin-film photonic band edge lasing devices using dye-doped low molar mass liquid crystals in self-organised chiral nematic and blue phases. We show that high Q-factor lasers can be achieved in these materials and demonstrate that a single mode output with a very narrow line width can be readily achievable in well-aligned mono-domain samples. Further, we have found that the performance of the laser, i.e. the slope efficiency and the excitation threshold, are dependent upon the physical parameters of the low molar mass chiral nematic liquid crystals. Specifically, slope efficiencies greater than 60% could be achieved depending upon the materials used and the device geometry employed. We will discuss the important parameters of the liquid crystal host/dye guest materials and device configuration that are needed to achieve such high slope efficiencies. Further we demonstrate how the wavelength of the laser can be tuned using an in-plane electric field in a direction perpendicular to the helix axis via a flexoelectric mechanism as well as thermally using thermochromic effects. We will then briefly outline data on room temperature blue phase lasers and further show how liquid crystal/lenslet arrays have been used to demonstrate 2D laser emission of any desired wavelength. Finally, we present preliminary data on LED/incoherent pumping of RG liquid crystal lasers leading to a continuous wave output. © 2009 SPIE.

Frog albumin is expressed in skin and characterized as a novel potent trypsin inhibitor

A novel potent trypsin inhibitor was purified and characterized from frog Bombina maxima skin. A full-length cDNA encoding the protein was obtained from a cDNA library constructed from the skin. Sequence analysis established that the protein actually comprises three conserved albumin domains. B. maxima serum albumin was subsequently purified, and its coding cDNA was further obtained by PCR-based cloning from the frog liver. Only two amino acid variations were found in the albumin sequences from the skin and the serum. However, the skin protein is distinct from the serum protein by binding of a haem b (0.95 mol/mol protein). Different from bovine serum albumin, B. maxima albumin potently inhibited trypsin. It bound tightly with trypsin in a 1: 1 molar ratio. The equilibrium dissociation constants (K-D) obtained for the skin and the serum proteins were 1.92 x 10(-9) M and 1.55 x 10(-9) M, respectively. B. maxima albumin formed a noncovalent complex with trypsin through an exposed loop formed by a disulfide bond (Cys(53)-Cys(62)), which comprises the scissile bond Arg(58)(P-1)-His(59)(P-1'). No inhibitory effects on thrombin, chymotrypsin, elastase, and subtilisin were observed under the assay conditions. Immunohistochemical study showed that B. maxima albumin is widely distributed around the membranes of epithelial layer cells and within the stratum spongiosum of dermis in the skin, suggesting that it plays important roles in skin physiological functions, such as water economy, metabolite exchange, and osmoregulation.

Cloning of bradykinin precursor cDNAs from skin of Bombina maxima reveals novel bombinakinin M antagonists and a bradykinin potential peptide

Bombinakinin M (DLPKINRKGP-bradykinin) is a bradykinin-related peptide purified from skin secretions of the frog Bombina maxima. As previously reported, its biosynthesis is characterized by a tandem repeats with various copy numbers of the peptide and sometimes co-expressed with other structure-function distinguishable peptides. At present study, two novel cDNAs encoding bombinakinin M and its variants were cloned from a cDNA library from the skin of the frog. The encoded two precursor proteins are common in that each contains three repeats of a novel 16-amino acid peptide unit and one copy of kinestatin at their N- and C-terminal parts, respectively. They differ in that the first precursor contains two copies of bombinakinin M and the second one contains one copy of a novel bombinakinin M variant. Bombinakinin M was found to elicit concentration-dependent contractile effects on guinea pig ileum, with an EC50 value of 4 nM that is four times higher than that of bradykinin (1 nM). Interestingly, the synthetic peptide (DYTIRTRLH-amide), as deduced from the 16-amino acid peptide repeats in the newly cloned cDNAs, possessed weak inhibitory activity on the contractile effects of bombinakinin M, but not on that of bradykinin. Furthermore, the newly identified bombinakinin M variant (DLSKMSFLHG-Ile(1)-bradykinin), did not show contractile activity on guinea pig ileum, but showed potentiation effect on the myotropic activity of bradykinin. In a molar raito of 1:58, it augmented the activity of bradykinin up to two-fold. (C) 2004 Elsevier B.V. All rights reserved.

Perylene-based fluorescent liquid crystal dye guest-host mixtures

We present a study on a series of dye guest-host mixtures using fluorescent perylene-based molecules as the guest dye in an organosiloxane host. These hosts have temperature-independent switching, at room temperature, through 90° for fields of the order of 10 Vrms/μm. Perylene molecules have been grafted onto the organosiloxane moiety via an alkyl spacer producing novel and rugged fluorescent dyes that are readily miscible in the host. Micro-separation of the low molar mass siloxane groups in the mesophases tend to form smectic phases. These planes produce an effective two-dimensional polymer backbonethat engenders the rugged mechanical properties of polymeric liquid crystals onto these low molar mass ferroelectric liquid crystals. In this study we show how the introduction of the dye molecules affects the electro-optic properties of the organosiloxane host. © 2001 OPA (Overseas Publishers Association) N.V. Published by license under the Gordon and Breach Science Publishers imprint, a member of the Taylor & Francis Group,.

Red-Green-Blue 2D tuneable liquid crystal laser devices

In this paper, we review our recent experimental work on coherent and blue phase liquid crystal lasers.We will present results on thin-film photonic band edge lasing devices using dye-doped low molar mass liquid crystals in self-organised chiral nematic and blue phases. We show that high Q-factor lasers can be achieved in these materials and demonstrate that a single mode output with a very narrow line width can be readily achievable in well-aligned mono-domain samples. Further, we have found that the performance of the laser, i.e. the slope efficiency and the excitation threshold, are dependent upon the physical parameters of the low molar mass chiral nematic liquid crystals. Specifically, slope efficiencies greater than 60% could be achieved depending upon the materials used and the device geometry employed. We will discuss the important parameters of the liquid crystal host/dye guest materials and device configuration that are needed to achieve such high slope efficiencies. Further we demonstrate how the wavelength of the laser can be tuned using an in-plane electric field in a direction perpendicular to the helix axis via a flexoelectric mechanism as well as thermally using thermochromic effects. We will then briefly outline data on room temperature blue phase lasers and further show how liquid crystal/lenslet arrays have been used to demonstrate 2D laser emission of any desired wavelength. Finally, we present preliminary data on LED/incoherent pumping of RG liquid crystal lasers leading to a continuous wave output. © 2009 SPIE.

Reversible CO2 absorption by the 6H perovskite Ba 4Sb2O9

A novel compound for carbon capture and storage (CCS) applications, the 6H perovskite Ba4Sb2O9, was found to be able to absorb CO2 through a chemical reaction at 873 K to form barium carbonate and BaSb2O6. This absorption was shown to be reversible through the regeneration of the original Ba4Sb 2O9 material upon heating above 1223 K accompanied by the release of CO2. A combined synchrotron X-ray diffraction, thermogravimetric, and microscopy study was carried out to characterize first the physical absorption properties and then to analyze the structural evolution and formation of phases in situ. Importantly, through subsequent carbonation and regeneration of the material over 100 times, it was shown that the combined absorption and regeneration reactions proceed without any significant reduction in the CO2 absorption capacity of the material. After 100 cycles the capacity of Ba4Sb2O9 was ∼0.1 g (CO 2)/g (sorbent), representing 73% of the total molar capacity. This is the first report of a perovskite-type material showing such good properties, opening the way for studies of new classes of inorganic oxide materials with stable and flexible chemical compositions and structures for applications in carbon capture. © 2013 American Chemical Society.

A novel method of extraction of blend component structure from SANS measurements of homopolymer bimodal blends

A new method is presented for the extraction of single-chain form factors and interchain interference functions from a range of small-angle neutron scattering (SANS) experiments on bimodal homopolymer blends. The method requires a minimum of three blends, made up of hydrogenated and deuterated components with matched degree of polymerization at two different chain lengths, but with carefully varying deuteration levels. The method is validated through an experimental study on polystyrene homopolymer bimodal blends with M A≈1/2MB. By fitting Debye functions to the structure factors, it is shown that there is good agreement between the molar mass of the components obtained from SANS and from chromatography. The extraction method also enables, for the first time, interchain scattering functions to be produced for scattering between chains of different lengths. © 2014 The Authors. Published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Composition deviation of arrays of FePt nanoparticles starting from poly(styrene)-poly(4-vinylpyridine) micelles

Ordered arrays of FePt nanoparticles were prepared using a diblock polymer micellar method combined with plasma treatment. Rutherford backscattering spectroscopy analyses reveal that the molar ratios of Fe to Pt in metal-salt-loaded micelles deviate from those when metal precursors are added, and that the plasma treatment processes have little influence upon the compositions of the resulting FePt nanoparticles. The results from Fourier transform infrared spectroscopy show that the maximum loadings of FeCl3 and H2PtCl6 inside poly( styrene)-poly(4-vinylpyridine) micelles are different. The composition deviation of FePt nanoparticles is attributed to the fact that one FeCl3 molecule coordinates with a single 4-vinylpyridine (4VP) unit, while two neighboring and uncomplexed 4VP units are required for one H2PtCl6 molecule. Additionally, we demonstrate that the center-to-center distances of the neighboring FePt nanoparticles can also be tuned by varying the drawing velocity.

Microorganisms linked to Neoproterozoic microspar carbonate sedimentation in the Jilin-Liaoning area

Molar-tooth carbonate refers to a sort of rock that has ptygmatical folded structure comparable to the ivory. This kind of carbonate exists in a special time range (from Middle to Neoproterozoic). Its origin and the possibility to use it in stratigraphic correlation of the paleocontinent is the key task of the IGCP447, a project on Proterozoic molar tooth carbonates and the evolution of the earth (2001-2005). The importance lies in that the molar-tooth structure is the key to solving problems related to Precambrian biological and global geochemical events. The molar-tooth structure is associated with microorganisms. Development and recession of such carbonates have relations with the evolution process of early lives and abrupt changes in sea carbonate geochemistry. In recent years, based on researches on petrology, geochemistry and Sr isotope of molar-tooth carbonate in the Jilin-Liaoning and Xuzhou-Huaiyang area, the authors hold that it can be used as a marker for stratigraphic sequence and sedimentary facies analyses.

Large-scale synthesis of single-phase, high-quality GaN nanocrystallites

Large-scale synthesis of high-quality GaN nano-crystallites has been achieved by direct reaction of a 4:1 molar Ga/Ga2O3 mixture with ammonia at 950degreesC. X-ray diffraction, transmission electron microscopy, selected-area electron diffraction and high-resolution transmission electron microscopy revealed that the produced GaN nanocrystallites were single hexagonal wurtzite structure with an average particle size around 45 nm. A sharp near band edge emission peak and a blue light emission peak were observed in photoluminescence spectroscopy. The synthesis approach is simple and easy to be commercialized.

Effect of spontaneous and piezoelectric polarization on intersubband transition in AlxGa1-xN-GaN quantum well

A self-consistent solution of conduction band profile and subband energies for AlxGa1-xN-GaN quantum well is presented by solving the Schrodinger and Poisson equations. A new method is introduced to deal with the accumulation of the immobile charges at the AlxGa1-xN-GaN interface caused by spontaneous and piezoelectric polarization in the process of solving the Poisson equation. The effect of spontaneous and piezoelectric polarization is taken into account in the calculation. It also includes the effect of exchange-correlation to the one electron potential on the Coulomb interaction. Our analysis is based on the one electron effective-mass approximation and charge conservation condition. Based on this model, the electron wave functions and the conduction band structure are derived. We calculate the intersubband transition wavelength lambda(21) for different Al molar fraction of barrier and thickness of well. The calculated result can fit to the experimental data well. The dependence of the absorption coefficient a on the well width and the doping density is also investigated theoretically. (C) 2004 American Vacuum Society.

Quasi-thermo dynamic analysis of MOVPE growth of GaxAlyIn1-x-yN

A quasi-thermodynamic model of metalorganic vapor phase epitaxy (MOVPE) growth of GaxAlyIn1-x-yN alloys has been proposed. In view of the complex growth behavior of GaxAlyIn1-x-yN, we focus our attention on the galliumrich quaternary alloys that are lattice matched to GaN, In0.15Ga0.85N or Al0.15Ga0.85N, which are widely used in the GaN-based optoelectronic devices. The relationship between GaAlInN alloy composition and input molar ratio of group III metalorganic compounds at various growth conditions has been calculated. The influence of growth temperature, nitrogen fraction in the carrier gas, input partial pressure of group III metalorganics, reactor pressure, V/III ratio and the decomposition rate of ammonia on the composition of deposited alloys are studied systematically. Based on these calculated results, we can find out the appropriate growth conditions for the MOVPE growth of GaxAlyIn1-x-yN alloy lattice matched to GaN, In0.15Ga0.85N or Al0.15Ga0.85N. (C) 2002 Elsevier Science B.V. All rights reserved.

The dependence of growth rate of GaN buffer layer on growth parameters by metalorganic vapor-phase epitaxy

The growth rate of GaN buffer layers on sapphire grown by metalorganic vapor-phase epitaxy (MOVPE) in an atmospheric pressure, two-channel reactor was studied. The growth rate, as measured using laser reflectance, was found to be dependent on growth temperature, molar flow rate of the sources tin this case, trimethylgallium and ammonia) and the input configuration of sources into the reactor. A model of the GaN buffer layer growth process by MOVPE is proposed to interpret the experimental evidence. (C) 1998 Elsevier Science B.V. All rights reserved.

酸化油固定床酶法合成生物柴油研究

酸化油是油脂工业中以皂脚、油脚经酸化处理得到的产品。它的主要成分是游离脂肪酸及中性油，是生产脂肪酸的重要原料，但生产过程中有水解废水的产生，若将其直接排放，既污染了环境又浪费了资源。生物柴油的主要成分是脂肪酸甲酯（fatty acid methyl ester，FAME）。它具有原料丰富而且可再生、可生物降解、无毒、不含芳香烃、二氧化硫等污染物、燃烧排放低、闪点高、运输储存安全等特点。作为石化柴油的潜在替代能源，生物柴油因其独特的优越性和现实的需求越来越受到关注。利用酸化油生产生物柴油不仅可以缓解生物柴油原料不足问题，还可解决酸化油所带来的环境问题。

The convertion of acid oil to biodiesel by use of immobilized Candida lipase absorbed on textile cloth was studied in a fixed bed reactor, which can not only reduce the environmental pollution of acid oil, but also produce a substitute for petroleum diesel. The acid oil mixed with methanol was pumped into three fixed bed reactors in series, and the methanol was added with the molar flow rate same as the acid oil in each reactor. The effects of enzyme content, solvent content, water content, flow rate of reactant and temperature on the enzymatic reaction were analyzed. The result of orthogonal experiments indicates that the optimal transesterification can be performed under the following conditions： immobilized lipase content in acid oil, 20% ; hexane content in acid oil, 10% ; water content in acid oil, 10%, reaction temperature, 50 ℃ ; and flow rate of reactant, 0.08 g/rain. Under these conditions, the FAME content of 90.18% in the product is obtained. The immobilized lipase can be reused with relatively stable activity after glycerol being removed from the surface. By refining, most of the chemical and physical properties of biodiesel will meet the American and Germany biodiesel standards and exceed the Chinese standard of 0^# petroleum diesel except for carbon residue, density and kinematic viscosity.

酸化油固定床酶法合成生物柴油研究

以固定化的假丝酵母酶为催化剂，在三段式固定床反应器内，醇油摩尔比为1：1，采用分级流加甲醇的方式，将高酸值的酸化油转化为生物柴油，探讨了酶量、溶剂量、水量、温度、反应液流速等与产物中甲酯含量的关系。正交实验结果表明，反应的最适条件为酶用量、溶剂量、水量分别为油重的15％、10％、10％，反应液流速为0.8g·min^-1，温度为45℃，在此条件下，产物中甲酯含量达到了90．18％。