Mejora de la seguridad de las presas de escollera frente a percolación accidental mediante protecciones tipo repié

Esta tesis doctoral es el fruto de un trabajo de investigación cuyo objetivo principal es definir criterios de diseño de protecciones en forma de repié en presas de materiales sueltos cuyo espaldón de aguas abajo esté formado por escollera. La protección propuesta consiste en un relleno de material granular situado sobre el pie de aguas abajo de la presa y formado a su vez por una escollera con características diferenciadas respecto de la escollera que integra el espaldón de la presa. La función de esta protección es evitar que se produzcan deslizamientos en masa cuando una cantidad de agua anormalmente elevada circula accidentalmente por el espaldón de aguas abajo de la presa por distintos motivos como pueden ser el vertido por coronación de la presa o la pérdida de estanqueidad del elemento impermeable o del cimiento. Según los datos de la International Commission on Large Dams (ICOLD 1995) el 70% de las causas de rotura o avería grave en presas de materiales sueltos en el mundo están dentro de las que se han indicado con anterioridad. Esta circulación accidental de agua a través del espaldón de escollera, típicamente turbulenta, se ha denominado en esta tesis percolación (“through flow”, en inglés) para diferenciarla del término filtración, habitualmente utilizada para el flujo laminar a través de un material fino. El fenómeno físico que origina la rotura de presas de materiales sueltos sometidas a percolación accidental es complejo, entrando en juego diversidad de parámetros, muchas veces no deterministas, y con acoplamiento entre procesos, tanto de filtración como de arrastre y deslizamiento. En esta tesis se han realizado diferentes estudios experimentales y numéricos con objeto de analizar el efecto sobre el nivel de protección frente al deslizamiento en masa que producen los principales parámetros geométricos que definen el repié: la anchura de la berma, el talud exterior y su altura máxima desde la base. También se han realizado estudios sobre factores con gran influencia en el fenómeno de la percolación como son la anisotropía del material y el incremento de los caudales unitarios en el pie de presa debidos a la forma de la cerrada. A partir de los resultados obtenidos en las distintas campañas de modelación física y numérica se han obtenido conclusiones respecto a la efectividad de este tipo de protección para evitar parcial o totalmente los daños provocados por percolación accidental en presas de escollera. El resultado final de la tesis es un procedimiento de diseño para este tipo de protecciones. Con objeto de completar los criterios de dimensionamiento, teniendo en cuenta los mecanismos de rotura por erosión interna y arrastre, se han incluido dentro del procedimiento recomendaciones adicionales basadas en investigaciones existentes en la bibliografía técnica. Finalmente, se han sugerido posibles líneas de investigación futuras para ampliar el conocimiento de fenómenos complejos que influyen en el comportamiento de este tipo de protección como son el efecto de escala, la anisotropía de la escollera, las leyes de resistencia que rigen la filtración turbulenta a través de medios granulares, los efectos de cimentaciones poco competentes o la propia caracterización de las propiedades de la escollera de presas. This thesis is the result of a research project that had the main objective of defining criteria to design rockfill toe protections for dams with a highly‐permeable downstream shoulder. The proposed protection consists of a rockfill toe berm situated downstream from the dam with specific characteristics with respect to the rockfill that integrates the shoulder of the main dam. The function of these protections is to prevent mass slides due to an abnormally high water flow circulation through the dam shoulder. This accidental seepage flow may be caused by such reasons as overtopping or the loss of sealing at the impervious element of the dam or its foundation. According to data from the International Commission on Large Dams (ICOLD 1995), 70% of the causes of failure or serious damage in embankment dams in the world are within that described previously. This accidental seepage of water through the rockfill shoulder, typically turbulent, is usually called through‐flow. The physical phenomenon which causes the breakage of the rockfill shoulder during such through‐flow processes is complex, involving diversity of parameters (often not deterministic) and coupling among processes, not only seepage but also internal erosion, drag or mass slide. In this thesis, numerical and experimental research is conducted in order to analyze the effects of the main parameters that define the toe protection, i.e. the toe crest length, its slope and maximum height. Additional studies on significant factors which influence the seepage, such as the anisotropy of the material and the increase of the unit flows at the dam toe due to the valley shape are also performed. In addition, conclusions regarding the effectiveness of this type of protection are obtained based on the results of physical and numerical models. The main result of the thesis is a design procedure for this type of protection to avoid mass sliding. In order to complete the design criteria, additional recommendations about internal and external erosion based on the state of the art are included. Finally, new lines of research are suggested for the future to expand the level of knowledge of the complex phenomena that influence the behavior of this type of protection, such as the effects of scale, rockfill anisotropy, non‐linear seepage laws in turbulent seepage through granular media, effects of erodible foundations, or new procedures to characterize the properties of dam rockfill as a construction material.

Building a New Water Culture in Spain

For over 100 years, water policy and man­ agement in Spain have been instruments of economic and social transformation. Sig­ nificant public and private investments in water supply infrastructures have equipped Spain with over 1,200 major dams, 20 major desalination plants ? with more under construction ? and several inter­basin water transfers. The system has been apparently very successful, with an increase in overall water availability, strong associated eco­ nomic development and few urban water supply shortages. This success has been supported by a widespread consensus among a strong and largely closed water policy community made up of water manag­ ers, irrigators, electric (hydropower) utilities and developers.

Inspección técnica de la presa Santa Marta, mediante medidas subacuáticas de potencial espontáneo

Las filtraciones de agua, con la consecuente erosión interna en presas de materiales sueltos, es una de las causas principales de fallos y accidentes. Las consecuencias del fallo de estas estructuras, pueden ser, pérdidas tanto económicas como de vidas humanas. Por lo cual en este proyecto se describe la aplicación de un método de prospección geofísica no invasiva, medidas de potencial espontáneo, para detectar posibles filtraciones de agua en el cuerpo de la presa. El flujo de agua a través de un material poroso y permeable crea un campo de potencial eléctrico de una magnitud de decenas o centenas de milivoltios, el cual puede ser medido y así detectar infiltraciones de agua en presas de materiales sueltos. Se ha aplicado esta técnica en la Presa Santa Marta, y mediante una interpretación cualitativa de los datos medidos, tomados en la cara aguas arriba de la presa (medidas subacuáticas), se logró identificar un flujo de agua vertical y otro subhorizontal, que estaban ingresando en el cuerpo de la presa, los cuales estaban causando erosión interna y la formación de una tubificación. ABSTRACT Water leakages and internal erosion in embankment dams is one of the main causes of failures and accidents. The consequences of the failure of these structures may cause losses both, economical and of human lives. Therefore, this project describes the application of a noninvasive geophysical prospecting method, self potential measurements, to detect water leakages in the body of the dam. Water flow through a porous and pervious medium creates an electric potential field with a magnitude of tens or hundreds of milivolts, which can be measured and thus detect water leakage in embankment dams. This technique has been applied to the Santa Marta dam, and through a qualitative self potential data interpretation, of the measurements obtained in an upstream direction (underwater measurements), a vertical and sub horizontal water flows entering in the body dam were identified, which were causing internal erosion and developing a piping

Simulation of Temperatures and Stresses during Construction of a RCC Dam

Se describen las variaciones de temperaturas y de tensiones durante la construcción de presas de hormigón compactado. The curing of concrete is an exothermic process. The heat of hydration generated induces temperature increases in the concrete, which will disappear in the long term by heat conduction in the concrete mass and thermal exchanges with the environment. The problem is of particularly interest for large concrete masses, as is the case of dams, because the time involved in the heat diffusion process grows with the square of the dimensions and a hotter dam interior implies the possibility of cracking the exposed surfaces of the dam. The Cuira dam, currently being built in Venezuela using roller compacted concrete, is a 134 m high, arch-gravity dam. In support of the design, different strategies were analysed, including various combinations of cooling of the water and the aggregate in order to achieve acceptable results. The calculations were conducted with Abaqus, taking into account all the necessary mechanical and thermal characteristics, as well as the relevant non-linearities. The analyses led to the conclusion that no cooling was required, even taking into account the stress state imposed by an early and rapid filling of the reservoir.

Concrete Swelling in a Double Curvature Dam

Se describe el problema del hinchamiento del hormigón en las presas de doble curvatura. Several chemical reactions are able to produce swelling of concrete for decades after its initial curing, a problem that affects a considerable number of concrete dams around the world. The object of the work reported is to simulate the underlying mechanisms with sufficient accuracy to reproduce the past history and to predict the future evolution reliably. Having studied the available formulations, that considered to be more promising was adopted and introduced via user routines in a commercial finite element code. It is a non isotropic swelling model,compatible with the cracking and other non-linearities displayed by the concrete. The paper concentrates on the work conducted for a double-curvature arch dam. The model parameters were determined on the basis of some parts of the dam’s monitored histories, reliability was then verified using other parts and, finally, predictions were made about the future evolution of the dam and its safety margin.

Fluid-Structure Interaction in Civil Engineering Structures

The problems being addressed involve the dynamic interaction of solids (structure and foundation) with a liquid (water). Various numerical procedures are reviewed and employed to solve the problem of establishing the expected response of a structure subjected to seismic excitations while duly accounting for those interactions. The methodology is applied to the analysis of dams, lock gates, and large storage tanks, incorporating in some cases a comparison with the results produced by means of simplified analytical procedures.

Survey on integration of Applied Geology and Geomorphology in Civil Engineering curricula in the framework of the European Higher Education Area (EHEA) by using practical trips

The engineer must have sufficient theoretical knowledge to be applied to solve specific problems, with the necessary capacity to simplify these approaches, and taking into account factors such as speed, simplicity, quality and economy. In Geology, its ultimate goal is the exploration of the history of the geological events through observation, deduction, reasoning and, in exceptional cases by the direct underground exploration or experimentation. Experimentation is very limited in Geology. Reproduction laboratory of certain phenomena or geological processes is difficult because both time and space become a large scale. For this reason, some Earth Sciences are in a nearly descriptive stage whereas others closest to the experimental, Geophysics and Geochemistry, have assimilated progress experienced by the physics and chemistry. Thus, Anglo-Saxon countries clearly separate Engineering Geology from Geological Engineering, i.e. Applied Geology to the Geological Engineering concepts. Although there is a big professional overlap, the first one corresponds to scientific approach, while the last one corresponds to a technological one. Applied Geology to Engineering could be defined as the Science and Applied Geology to the design, construction and performance of engineering infrastructures in and field geology discipline. There has been much discussion on the primacy of theory over practice. Today prevails the exaggeration of practice, but you get good workers and routine and mediocre teachers. This idea forgets too that teaching problem is a problem of right balance. The approach of the action lines on the European Higher Education Area (EHEA) framework provides for such balance. Applied Geology subject represents the first real contact with the physical environment with the practice profession and works. Besides, the situation of the topic in the first trace of Study Plans for many students implies the link to other subjects and topics of the career (tunnels, dams, groundwater, roads, etc). This work analyses in depth the justification of such practical trips. It shows the criteria and methods of planning and the result which manifests itself in pupils. Once practical trips experience developed, the objective work tries to know about results and changes on student’s motivation in learning perspective. This is done regardless of the outcome of their knowledge achievements assessed properly and they are not subject to such work. For this objective, it has been designed a survey about their motivation before and after trip. Survey was made by the Unidad Docente de Geología Aplicada of the Departamento de Ingeniería y Morfología del Terreno (Escuela Técnica Superior de Ingenieros de Caminos, Canales y Puertos, Universidad Politécnica de Madrid). It was completely anonymous. Its objective was to collect the opinion of the student as a key agent of learning and teaching of the subject. All the work takes place under new teaching/learning criteria approach at the European framework in Higher Education. The results are exceptionally good with 90% of student’s participation and with very high scores in a number of questions as the itineraries, teachers and visited places (range of 4.5 to 4.2 in a 5 points scale). The majority of students are very satisfied (average of 4.5 in a 5 points scale).

Estudio de redes WSN y su aplicación a la ingeniería civil

Las redes inalámbricas están experimentando un gran crecimiento en el campo de la instrumentación electrónica. En concreto las redes de sensores inalámbricas (WSN de Wireless Sensor Network) suponen la opción más ventajosa para su empleo en la instrumentación electrónica ya que sus principales características se acoplan perfectamente a las necesidades. Las WSN permiten la utilización de un número relativamente alto de nodos, están orientadas a sistemas de bajo consumo y funcionamiento con baterías y poseen un ancho de banda adecuado para las necesidades de la instrumentación electrónica. En este proyecto fin de carrera se ha realizado un estudio de las tecnologías inalámbricas disponibles, se han comparado y se ha elegido la tecnología ZigBeeTM por considerarse la más adecuada y la que más se ajusta a las necesidades descritas. En el desarrollo de mi vida profesional se han conectado dos campos teóricamente distantes como son la instrumentación electrónica y la ingeniería civil. En este proyecto se hace una descripción de la instrumentación que se utiliza para controlar estructuras como presas, túneles y puentes y se proponen casos prácticos en los que las redes WSN aportan valor añadido a instrumentación actual y a los sistemas de comunicaciones utilizados. Se definen tanto los sistemas de comunicaciones utilizados actualmente como una serie de sensores utilizados para medir los principales parámetros a controlar en una obra civil. Por último se ha desarrollado una aplicación de prueba de una red ZigBeeTM basada en equipos comerciales del fabricante Digi. consiste en una aplicación desarrollada en entorno web que maneja de forma remota, a través de Internet, las entradas y salidas digitales y analógicas de los nodos que forman la red. Se forma una red ZigBeeTM con un coordinador, un router y un dispositivo final. El Coordinador está integrado en un Gateway que permite acceder a la red ZigBeeTM a través de internet y conocer el estado de los nodos que forman la red. Con los comandos adecuados se puede leer el estado de las entradas y salidas analógicas y digitales y cambiar el estado de una salida digital. ABSTRACT. Wireless networks are experiencing tremendous growth in the field of electronic instrumentation. In particular wireless sensor networks represent the most advantageous for use in electronic instrumentation since its main characteristics fit perfectly to the needs. The WSN allow the use of a relatively large number of nodes, are aimed at low-power systems and battery operation and have an adequate bandwidth for the needs of electronic instrumentation. In this project has made a study of available wireless technologies have been compared and chosen ZigBeeTM technology was considered the most appropriate to the needs described. In the course of my professional life have connected two fields are theoretically distant as electronic instrumentation and civil engineering. In this project, there is a description of the instrumentation used to control structures such as dams, tunnels and bridges and proposes practical cases in which WSN networks add value to current instrumentation and communications systems used. There are defined as communications systems now being used as a set of sensors used to measure the main parameters to be controlled in a civil structure. Finally, I have developed a test application based ZigBeeTM networking equipment maker Digi trading. It consists of a Web-based application developed to manage remotely, via the Internet, the digital and analog inputs and outputs nodes forming the network. ZigBeeTM It forms a network with a coordinator, router and end device. The Coordinator is built into a gateway that allows access to the ZigBeeTM network through internet and know the status of the nodes forming the network. With the appropriate command can read the status of the digital inputs and outputs and change the state of a digital output.

Esfuerzos inducidos en presas, arco-gravedad en operación por la acción térmica medioambiental : una aportación a su análisis y evaluación

Cyclic fluctuations of the atmospheric temperature on the dam site, of the water temperature in the reservoir and of the intensity of solar radiation on the faces of the dam cause significant stresses in the body of concrete dams. These stresses can be evaluated first by introducing in analysis models a linear temperature distribution statically equivalent to the real temperature distribution in the dam; the stress valúes obtained from this first step must be complemented (especially in the área of dam faces) with the stress valúes resuiting from the difference between the real temperature law and the linear law at each node. In the case of arch gravity dams, and because of their characteristics of arch dam featuring a thick section, both types of temperature-induced stresses are of similar importance. Thermal stress valúes are directly linked to a series of factors: atmospheric and water temperature and intensity of solar radiation at dam site, site latitude, azimuth of the dam, as well as geometrical characteristics of the dam and thermal properties of concrete. This thesis first presents a complete study of the physical phenomenon of heat exchange between the environment and the dam itself, and establishes the participation scheme of all parameters involved in the problem considered. A detailed documental review of available methods and techniques is then carried out both for the estimation of environmental thermal loads and for the evaluation of the stresses induced by these loads. Variation ranges are also established for the main parameters. The definition of the geometrical parameters of the dam is provided based on the description of a wide set of arch gravity dams built in Spain and abroad. As a practical reference of the parameters defining the thermal action of the environment, a set of zones, in which thermal parameters reach homogeneous valúes, was established for Spain. The mean valué and variation range of atmospheric temperature were then determined for each zone, based on a series of historical valúes. Summer and winter temperature increases caused by solar radiation were also defined for each zone. Since the hypothesis of thermal stratification in the reservoir has been considered, máximum and mínimum temperature valúes reached at the bottom of the reservoir were determined for each climatic zone, as well as the law of temperature variation in function of depth. Various dam-and-foundation configurations were analysed by means of finite element 3D models, in which the dam and foundation were each submitted to different load combinations. The seasonal thermal behaviour of sections of variable thickness was analysed through the application of numerical techniques to one-dimensional models. Contrasting the results of both analyses led to conclusions on the influence of environmental thermal action on the stress conditions of the structure. Las oscilaciones periódicas de la temperatura ambiente en el emplazamiento y de la temperatura del agua en el embalse, así como de la incidencia de la radiación solar sobre los paramentos de la presa, son causa de tensiones importantes en el cuerpo de las presas de hormigón. Estas tensiones pueden ser evaluadas en primer lugar introduciendo en los modelos tridimensionales de análisis, distribuciones lineales de temperatura estáticamente equivalentes a las correspondientes distribuciones reales en el cuerpo de la presa; las tensiones así obtenidas han de complementarse (sobre todo en las cercanías de los paramentos) con tensiones cuyo origen está en la temperatura diferencia entre la ley real y la lineal en cada punto. En el caso de las presas arco-gravedad y en razón de su doble característica de presas arco y de sección gruesa, ambas componentes de la tensión inducida por la temperatura son de magnitud similar. Los valores de estas tensiones de origen térmico están directamente relacionados con la temperatura del emplazamiento y del embalse, con la intensidad de la insolación, con la latitud y el azimut de la presa, con las características geométricas de la estructura y con las propiedades térmicas del hormigón. En esta tesis se realiza, en primer lugar, un estudio completo del fenómeno físico del intercambio de calor entre el medio ambiente y el cuerpo de la presa, estableciendo el mecanismo de participación de todos los parámetros que configuran el problema. En segundo lugar se realiza a cabo una revisión documental detallada de los métodos y técnicas utilizables tanto en la estimación de las cargas térmicas ambientales como en la evaluación de las tensiones inducidas por dichas cargas. En tercer lugar se establecen rangos de variación para los principales parámetros que configuran el problema. Los parámetros geométricos de la presa se definen a partir de la descripción de un amplio conjunto de presas arco-gravedad tanto españolas como del resto del mundo. Como referencia práctica de los parámetros que definen la acción térmica ambiental se establecen en España un conjunto de zonas caracterizadas por que, en cada una de ellas, los parámetros térmicos alcanzan valores homogéneos. Así, y en base a series de valores históricos, se establecen la media y la amplitud de la variación anual de la temperatura ambiental en cada una de las zonas. Igualmente, se han definido para cada zona los incrementos de temperatura que, en invierno y en verano, produce la insolación. En relación con el agua del embalse y en la hipótesis de estratificación térmica de este, se han definido los valores, aplicables en cada una de las zonas, de las temperaturas máxima y mínima en el fondo así como la ley de variación de la temperatura con la profundidad. Utilizando modelos tridimensionales de elementos finitos se analizan diferentes configuraciones de la presa y la cimentación sometidas, cada una de ellas, a diferentes combinaciones de carga. Aplicando técnicas numéricas a modelos unidimensionales se analiza el comportamiento térmico temporal de secciones de espesor variable. Considerando conjuntamente los resultados de los análisis anteriores se obtienen conclusiones parametrizadas de detalle sobre la influencia que tiene en el estado tensional de la estructura la consideración de la acción térmica ambiental.

Testing a GIS-based methodology for optimal location of Pumped Storage power plants in Norway

Europe needs to restructure its energy system. The aim to decrease the reliance on fossil fuels to a higher dependence on renewable energy has now been imposed by The European Commission. In order to achieve this goal there is a great interest in Norway to become "The Green Battery of Europe". In the pursuit of this goal a GIS-tool was created to investigate the pump storage potential in Norway. The tool searches for possible connections between existing reservoirs and dams with the criteria selected by the user. The aim of this thesis was to test the tool and see if the results suggested were plausible, develop a cost calculation method for the PSH lines, and make suggestions for further development of the tool. During the process the tool presented many non-feasible pumped storage hydropower (PSH) connections. The area of Telemark was chosen for the more detailed study. The results were discussed and some improvements were suggested for further development of the tool. Also a sensitivity test was done to see which of the parameters set by the user are the most relevant for the PSH connection suggestion. From a range of the most promising PSH plants suggested by the tool, the one between Songavatn and Totak was chosen for a case study, where there already exists a power plant between both reservoirs. A new Pumped Storage Plant was designed with a power production of 1200 MW. There are still many topics open to discussion, such as how to deal with environmental restrictions, or how to deal with inflows and outflows of the reservoirs from the existing power plants. Consequently the GIS-tool can be a very useful tool to establish the best possible connections between existing reservoirs and dams, but it still needs a deep study and the creation of new parameters for the user.

Analyzing climate change adaptation in the agriculture and water sectors: screening risks and opportunities.

As part of the Mediterranean area, the Guadiana basin in Spain is particularly exposed to increasing water stress due to climate change. Future warmer and drier climate will have negative implications for the sustainability of water resources and irrigation agriculture, the main socio- economic sector in the region. This paper illustrates a systematic analysis of climate change impacts and adaptation in the Guadiana basin based on a two-stage modeling approach. First, an integrated hydro-economic modeling framework was used to simulate the potential effects of regional climate change scenarios for the period 2000-2069. Second, a participatory multi-criteria technique, namely the Analytic Hierarchy Process (AHP), was applied to rank potential adaptation measures based on agreed criteria. Results show that, in the middle-long run and under severe climate change, reduced water availability, lower crop yields and increased irrigation demands might lead to water shortages, crop failure, and up to ten percent of income losses to irrigators. AHP results show how private farming adaptation measures, including improving irrigation efficiency and adjusting crop varieties, are preferred to public adaptation measures, such as building new dams. The integrated quantitative and qualitative methodology used in this research can be considered a socially-based valuable tool to support adaptation decision-making.

A water footprint assessment of a pair of jeans: the influence of agricultural policies on the sustainability of consumer products.

This study reports the results of a water footprint (WF) assessment of five types of textiles commonly used for the production of jeans, including two different fibres (cotton and Lyocell fibre) and five corresponding production methods for spinning, dyeing and weaving. The results show that the fibre production is the stage with the highest water consumption, being cotton production particularly relevant. Therefore, the study pays particular attention to the water footprint of cotton production and analyses the effects of external factors influencing the water footprint of a product, in this case, the incentives provided by the EU Common Agricultural Policy (CAP), and the relevance of agricultural practices to the water footprint of a product is emphasised. An extensification of the crop production led to higher WF per unit, but a lower overall pressure on the basins water resources. This study performs a sustainability assessment of the estimated cotton WFs with the water scarcity index, as proposed by Hoekstra et al. (2011), and shows their variations in different years as a result of different water consumption by crops in the rest of the river basin. In our case, we applied the assessment to the Guadalquivir, Guadalete and Barbate river basins, three semi-arid rivers in South Spain. Because they are found to be relevant, the available water stored in dams and the outflow are also incorporated as reference points for the sustainability assessment. The study concludes that, in the case of Spanish cotton production, the situation of the basin and the policy impact are more relevant for the status of the basin s water resources than the actual WF of cotton production. Therefore, strategies aimed at reducing the impact of the water footprint of a product need to analyse both the WF along the value chain and within the local context.

A bivariate return period based on copulas for hydrologic dam design: accounting for reservoir routing in risk estimation

A multivariate analysis on flood variables is needed to design some hydraulic structures like dams, as the complexity of the routing process in a reservoir requires a representation of the full hydrograph. In this work, a bivariate copula model was used to obtain the bivariate joint distribution of flood peak and volume, in order to know the probability of occurrence of a given inflow hydrograph. However, the risk of dam overtopping is given by the maximum water elevation reached during the routing process, which depends on the hydrograph variables, the reservoir volume and the spillway crest length. Consequently, an additional bivariate return period, the so-called routed return period, was defined in terms of risk of dam overtopping based on this maximum water elevation obtained after routing the inflow hydrographs. The theoretical return periods, which give the probability of occurrence of a hydrograph prior to accounting for the reservoir routing, were compared with the routed return period, as in both cases hydrographs with the same probability will draw a curve in the peak-volume space. The procedure was applied to the case study of the Santillana reservoir in Spain. Different reservoir volumes and spillway lengths were considered to investigate the influence of the dam and reservoir characteristics on the results. The methodology improves the estimation of the Design Flood Hydrograph and can be applied to assess the risk of dam overtopping

Fluoro-sensing applied to detection and identification of hydrocarbons in inland waters. Study of the impact of different UV light sources

This paper presents the detection and identification of hydrocarbons through flu oro-sensing by developing a simple and inexpensive detector for inland water, in contrast to current systems, designed to be used for marine waters at large distances and being extremely costly. To validate the proposed system, three test-benches have been mounted, with various UV-Iight sources. Main application of this system would be detect hydrocarbons pollution in rivers, lakes or dams, which in fact, is of growing interest by administrations.

Mejora de los modelos térmicos de las presas bóveda en explotación : aplicación al análisis del efecto del cambio climático

Las cargas de origen térmico causadas por las acciones medioambientales generan esfuerzos apreciables en estructuras hiperestáticas masivas, como es el caso de las presas bóvedas. Ciertas investigaciones apuntan que la variación de la temperatura ambiental es la segunda causa de reparaciones en las presas del hormigón en servicio. Del mismo modo, es una causa de fisuración en un porcentaje apreciable de casos. Las presas son infraestructuras singulares por sus dimensiones, su vida útil, su impacto sobre el territorio y por el riesgo que implica su presencia. La evaluación de ese riesgo requiere, entre otras herramientas, de modelos matemáticos de predicción del comportamiento. Los modelos han de reproducir la realidad del modo más fidedigno posible. Además, en un escenario de posible cambio climático en el que se prevé un aumento de las temperaturas medias, la sociedad ha de conocer cuál será el comportamiento estructural de las infraestructuras sensibles en los futuros escenarios climáticos. No obstante, existen escasos estudios enfocados a determinar el campo de temperaturas de las presas de hormigón. Así, en esta investigación se han mejorado los modelos de cálculo térmico existentes con la incorporación de nuevos fenómenos físicos de transferencia de calor entre la estructura y el medio ambiente que la rodea. También se han propuesto nuevas metodologías más eficientes para cuantificar otros mecanismos de transferencia de calor. La nueva metodología se ha aplicado a un caso de estudio donde se disponía de un amplio registro de temperaturas de su hormigón. Se ha comprobado la calidad de las predicciones realizadas por los diversos modelos térmicos en el caso piloto. También se han comparado los resultados de los diversos modelos entre sí. Finalmente, se ha determinado las consecuencias de las predicciones de las temperaturas por algunos de los modelos térmicos sobre la respuesta estructural del caso de estudio. Los modelos térmicos se han empleado para caracterizar térmicamente las presas bóveda. Se ha estudiado el efecto de ciertas variables atmosféricas y determinados aspectos geométricos de las presas sobre su respuesta térmica. También se ha propuesto una metodología para evaluar la respuesta térmica y estructural de las infraestructuras frente a los posibles cambios meteorológicos inducidos por el cambio climático. La metodología se ha aplicado a un caso de estudio, una presa bóveda, y se ha obtenido su futura respuesta térmica y estructural frente a diversos escenarios climáticos. Frente a este posible cambio de las variables meteorológicas, se han detallado diversas medidas de adaptación y se ha propuesto una modificación de la normativa española de proyecto de presas en el punto acerca del cálculo de la distribución de temperaturas de diseño. Finalmente, se han extraído una serie de conclusiones y se han sugerido posibles futuras líneas de investigación para ampliar el conocimiento del fenómeno de la distribución de temperaturas en el interior de las presas y las consecuencias sobre su respuesta estructural. También se han propuesto futuras investigaciones para desarrollar nuevos procedimiento para definir las cargas térmicas de diseño, así como posibles medidas de adaptación frente al cambio climático. Thermal loads produced by external temperature variations may cause stresses in massive hyperstatic structures, such as arch dams. External temperature changes are pointed out as the second most major repairs in dams during operation. Moreover, cracking is caused by thermal loads in a quite number of cases. Dams are unique infrastructures given their dimensions, lifetime, spatial impacts and the risks involve by their presence. The risks are assessed by means of mathematical models which compute the behavior of the structure. The behavior has to be reproduced as reliable as possible. Moreover, since mean temperature on Earth is expected to increase, society has to know the structural behavior of sensitive structures to climate change. However, few studies have addressed the assessment of the thermal field in concrete dams. Thermal models are improved in this research. New heat transfer phenomena have been accounted for. Moreover, new and more efficient methodologies for computing other heat transfer phenomena have been proposed. The methodology has been applied to a case study where observations from thermometers embedded in the concrete were available. Recorded data were predicted by several thermal models and the quality of the predictions was assessed. Furthermore, predictions were compared between them. Finally, the consequences on the stress calculations were analyzed. Thermal models have been used to characterize arch dams from a thermal point of view. The effect of some meteorological and geometrical variables on the thermal response of the dam has been analyzed. Moreover, a methodology for assessing the impacts of global warming on the thermal and structural behavior of infrastructures has been proposed. The methodology was applied to a case study, an arch dam, and its thermal and structural response to several future climatic scenarios was computed. In addition, several adaptation strategies has been outlined and a new formulation for computing design thermal loads in concrete dams has been proposed. Finally, some conclusions have been reported and some future research works have been outlined. Future research works will increase the knowledge of the concrete thermal field and its consequences on the structural response of the infrastructures. Moreover, research works will develope a new procedure for computing the design thermal loads and will study some adaptation strategies against the climate change.