Efficiency analysis of an isolated high voltage gain converter operating in resonant and non-resonant mode

This paper presents an efficiency investigation of an isolated high step-up ratio dc-dc converter aimed to be used for energy processing from low-voltage high-current energy sources, like batteries, photovoltaic modules or fuel-cells. The considered converter consists of an interleaved active clamp flyback topology combined with a voltage multiplier at the transformer secondary side capable of two different operating modes, i.e. resonant and non-resonant according to the design of the output capacitors. The main goal of this paper is to compare these two operating modes from the component losses point of view with the aim of maximize the overall converter efficiency. The approach is based on losses prediction using steady-state theoretical models (designed in Mathcad environment), taking into account both conduction and switching losses. The models are compared with steady-state simulations and experimental results considering different operating modes to validate the approach. © 2012 IEEE.

Identification of sperm head subpopulations with defined pleiomorphic characteristics in ejaculates of captive Goeldi's monkeys (Callimico goeldii)

The aim of this study was to evaluate the incidence of pleiomorphisms and its influence on the distribution of sperm morphometric subpopulations in ejaculates from the vulnerable Goeldi's monkey (Callimico goeldii) by using a combination of computerized analysis system and Principal Component Analysis (PCA) methods Each sperm head was measured for four primary spermatozoal head dimensional parameters (area [A (μm2)], perimeter [P (μm)], length [L (μm)] and width [W (μm)]) and three head shape derived parameters (ellipticity [(L/W)], elongation [(L-W)/(L+W)] and rugosity [(4πA/P2)]) Six separate subpopulations (SPs) were identified: SP1, constituted by very large, narrow and very elliptical spermatozoa (A=16.85±1.56μm2, W=2.75±0.42μm and ellipticity=2.16±0.24); SP2, characterized by average sized, short, wide and round spermatozoa (A=15.00±1.92μm2, L=5.06±0.49μm, W=3.51±0.31μm and ellipticity=1.44±0.15); SP3, represented by small, wide and slightly round spermatozoa (A=14.95±1.75μm2, W=3.47±0.29μm and ellipticity=1.48±0.14); SP4 included very small, short and very round spermatozoa (A=14.15±2.38μm2, L=4.90±0.57μm and elongation=0.18±0.05); SP5 consisted of average sized and slightly elliptical spermatozoa (A=15.14±1.72μm2 and ellipticity=1.49±0.14); and SP6 included large and round spermatozoa (A=16.30±1.62μm2 and elongation=0.19±0.04) There were differences in the sperm subpopulation distribution (P<0.001) among the five donors analyzed In conclusion, the results of the current study confirmed that the use of computer sperm analysis methods combined with PCA cluster analyses are useful methods to identify, classify, and characterize different sperm head morphometric subpopulations in neotropical primates Broadening our knowledge of C goeldii sperm morphometric abnormalities as well as developing reliable techniques for sperm evaluation may be essential for ex situ conservation of this threatened species © 2012 Elsevier B.V.

Effect of seed addition on SnO2-based varistors for low voltage application

The effect of seed addition on the microstructure and non-ohmic properties of the SnO2 + 1%CoO + 0.05%Nb2O5 ceramic-based system was analyzed. Two classes of seeds were prepared: 99% SnO2 + 1%CuO and 99% SnO2 + 1%CoO (mol%); both classes were added to the ceramic-based system in the amount of 1%, 5%, and 10%. The two systems containing 1% of seeds resulted in a larger grain size and a lower breakdown voltage. The addition of 1% copper seeds produces a breakdown voltage (V b) of ∼ 37 V and a leakage current (fic) of 29 μA. On the other hand, the addition of 1% cobalt seeds produced a breakdown voltage of 57 V and a leakage current of 70 μA. Both systems are of great technological interest for low voltage varistor applications, by means of appropriate strategies to reduce the leakage current. Using larger amounts of seeds was not effective since the values of breakdown voltage in both cases are close to a system without seeds. To our knowledge, there are no reports in the literature regarding the use of seeds in the SnO2 system for low voltage applications. A potential barrier model which illustrates the formation of oxygen species (O′2(ads), O′ads, and O″ads) at the expense of clusters near the interface between grains is proposed. © 2012 The American Ceramic Society.

Fault current limiter using transformer and modular device of YBCO coated conductor

In this work, we report on the evaluation of a superconducting fault current limiter (SFCL). It is consisted of a modular superconducting device combined with a short-circuited transformer with a primary copper winding connected in series to the power line and the secondary side short-circuited by the superconducting device. The basic idea is adding a magnetic component to contribute to the current limitation by the impedance reflected to the line after transition of the superconducting device. The evaluation tests were performed with a prospective current up to 2 kA, with the short-circuited transformer of 2.5 kVA, 220 V/660 V connected to a test facility of 100 kVA power capacity. The resistive SFCL using a modular superconducting device was tested without degradation for a prospective fault current of 1.8 kA, achieving the limiting factor 2.78; the voltage achieved 282 V corresponding to an electric field of 11 V/m. The test performed with the combined SFCL (xsuperconducting device + transformer) using series and toroidal transformers showed current limiting factor of 3.1 and 2 times, respectively. The test results of the combined SFCL with short-circuited transformer showed undesirable influence of the transformer impedance, resulting in reduction of the fault current level. © 2002-2011 IEEE.

The importance of size-exclusion characteristics of type I collagen in bonding to dentin matrices

The mineral phase of dentin is located primarily within collagen fibrils. During development, bone or dentin collagen fibrils are formed first and then water within the fibril is replaced with apatite crystallites. Mineralized collagen contains very little water. During dentin bonding, acid-etching of mineralized dentin solubilizes the mineral crystallites and replaces them with water. During the infiltration phase of dentin bonding, adhesive comonomers are supposed to replace all of the collagen water with adhesive monomers that are then polymerized into copolymers. The authors of a recently published review suggested that dental monomers were too large to enter and displace water from collagen fibrils. If that were true, the endogenous proteases bound to dentin collagen could be responsible for unimpeded collagen degradation that is responsible for the poor durability of resin-dentin bonds. The current work studied the size-exclusion characteristics of dentin collagen, using a gel-filtration-like column chromatography technique, using dentin powder instead of Sephadex. The elution volumes of test molecules, including adhesive monomers, revealed that adhesive monomers smaller than ∼1000 Da can freely diffuse into collagen water, while molecules of 10,000 Da begin to be excluded, and bovine serum albumin (66,000 Da) was fully excluded. These results validate the concept that dental monomers can permeate between collagen molecules during infiltration by etch-and-rinse adhesives in water-saturated matrices. © 2013 Acta Materialia Inc.

Metodologias de medição de energia elétrica reativa (varh) e erros de medição em equipamentos eletrônicos de (varh)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Retificador boost entrelaçado com elevado fator de potência e sem ponte de diodos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeitos das distorções harmônicas (tensões e correntes) e desequilíbrios (tensões) em medidores eletrônicos trifásicos de energia elétrica ativa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise e aplicação de compensação reativa em redes secundária de distribuição com cargas não lineares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Metodologia de projeto cooperativo para condicionadores de qualidade de energia

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo de uma ferramenta computacional inteligente para auxiliar a análise de ensaios de impulsos atmosféricos em transformadores de distribuição

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Um sistema eletrônico de 2kW para emulação/simulação experimental da característica estática de saída, tensão (versus) corrente, de sistemas de geração com células combustível tipo PEM

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Uma contribuição para o estudo do efeito causado pela névoa salina em isoladores cerâmicos de chaves fusíveis

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Transporte e características de onda de densidade de carga na ludwigita nomometálica Fe3O2BO3

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese e caracterização elétrica de compósitos poliméricos condutores com o poliuretano derivado de óleo de mamona como matriz

Pós-graduação em Ciência dos Materiais - FEIS