An Integrated Assessment Of The Suitability Of Domestic Solar Still As A Viable Safe Water Technology For India

Improving access to safe drinking water can result in multi-dimensional impacts on people's livelihood. This has been aptly reflected in the Millennium Development Goals (MDG) as one of the major objectives. Despite the availability of diverse and complex set of technologies for water purification, pragmatic and cost-effective use of the same is impeding the use of available sources of water. Hence, in country like India simple low-energy technologies such as solar still are likely to succeed. Solar stills would suffice the basic minimum drinking water requirements of man. Solar stills use sunlight, to kill or inactivate many, if not all, of the pathogens found in water. This paper provides an integrated assessment of the suitability of domestic solar still as a viable safe water technology for India. Also an attempt has been made to critically assess the operational feasibility and costs incurred for using this technology in rural India.

Processing and compressive strength of Al-Li-SiCp composites fabricated by a compound billet technique

Al-Li-SiCp composites were fabricated by a simple and cost effective stir casting technique. A compound billet technique has been developed to overcome the problems encountered during hot extrusion of these composites. After successful fabrication hardness measurement and room temperature compressive test were carried out on 8090 Al and its composites reinforced with 8, 12 and 18vol.% SiC particles in as extruded and peak aged conditions. The addition of SiC increases the hardness. 0.2% proof stress and compressive strength of Al-Li-8%SiC and Al-Li-12%SiC composites are higher than the unreinforced alloy. in case of the Al-Li-18%SiC composite, the 0.2% proof stress and compressive strength were higher than the unreinforced alloy but lower than those of Al-Li-8%SiC and Al-Li-12%SiC composites. This is attributed to clustering of particles and poor interfacial bonding.

Factors influencing sustainability of health service innovation: Emergency nurse practitioner services

Introduction: Emergency department nurse practitioner services are one of the most frequently implemented service delivery models in Australian hospitals. This research examined factors influencing sustainability of this innovative service delivery model and offers some recommendations for future service integration. Background Many health service innovations have been implemented in an attempt to meet the growing demand for efficient, cost effective health care however, sustainability of many of these innovations has not been evaluated and is poorly understood. Aim The aim of the research was to identify factors that influence sustainability of emergency department nurse practitioner services and to operationalise a theoretical framework for evaluating innovation sustainability. Methodology The research used case study methodology. The case was emergency nurse practitioner services, and units of analysis were emergency department staff, emergency nurse practitioners and documents relating to nurse practitioner services. The data collection methods included, survey, one-on-one interviews, document analysis and telephone survey. Results This research shows that emergency nurse practitioner services partially comply with the factors of sustainability as described in the Sustainability of Innovation theoretical framework: Political, Organisational, Workforce, Financial and Innovation specific factors. Where services do not entirely meet the factors the existing benefits of the service may outweigh the barriers and other means of working around shortfalls are also implemented by staff to ensure patient safety. Conclusion The rapidly expanding emergency nurse practitioner service has been examined using case study methodology to find that certain factors may be threatening the sustainability of this health service innovation. Potentially an innovation may be sustained when only some factors are met in the short term, however, long term sustainability may be challenged if factors are not addressed and supported.

Basic Needs and Much More With One Kilowatt Per Capita

Conventional thinkin g holds that increased energy consumption is a prerequisite for economic and social development. This belief, together With the prospect of dwindling global petroleum supplies and the high costs of expanding energy supply generally, lead many to believe that it is not feasible to improve living standards substantially in the developing countries. But by shifting to high-quality energy carriers and by exploiting cost-effective opportunities for more efficient energy use, it would be possible to satisfy basic human needs and to provide considerable further improvements in living standards without significantly increasing per-capita energy use above the present level.

Crystallization as a Tool for Controlling and Designing Properties of Pharmaceutical Solids

The ability to deliver the drug to the patient in a safe, efficacious and cost-effective manner depends largely on the physicochemical properties of the active pharmaceutical ingredient (API) in the solid state. In this context, crystallization is of critical importance in pharmaceutical industry, as it defines physical and powder properties of crystalline APIs. An improved knowledge of the various aspects of crystallization process is therefore needed. The overall goal of this thesis was to gain better understanding of the relationships between crystallization, solid-state form and properties of pharmaceutical solids with a focus on a crystal engineering approach to design technological properties of APIs. Specifically, solid-state properties of the crystalline forms of the model APIs, erythromycin A and baclofen, and the influence of solvent on their crystallization behavior were investigated. In addition, the physical phenomena associated with wet granulation and hot-melting processing of the model APIs were examined at the molecular level. Finally, the effect of crystal habit modification of a model API on its tabletting properties was evaluated. The thesis enabled the understanding of the relationship between the crystalline forms of the model APIs, which is of practical importance for solid-state control during processing and storage. Moreover, a new crystalline form, baclofen monohydrate, was discovered and characterized. Upon polymorph screening, erythromycin A demonstrated high solvate-forming propensity thus emphasizing the need for careful control of the solvent effects during formulation. The solvent compositions that yield the desirable crystalline form of erythromycin A were defined. Furthermore, new examples on solvent-mediated phase transformations taking place during wet granulation of baclofen and hot-melt processing of erythromycin A dihydrate with PEG 6000 are reported. Since solvent-mediated phase transformations involve the crystallization of a stable phase and hence affect the dissolution kinetics and possibly absorption of the API these transformations must be well documented. Finally, a controlled-crystallization method utilizing HPMC as a crystal habit modifier was developed for erythromycin A dihydrate. The crystals with modified habit were shown to posses improved compaction properties as compared with those of unmodified crystals. This result supports the idea of morphological crystal engineering as a tool for designing technological properties of APIs and is of utmost practical interest.

Up close and personal with those experiencing homelessness: Pharmacist involvement in a multidisciplinary healthcare team

Introduction. The Brisbane City Council holds a biannual Homeless Connect event which brings together business and community groups on one day to provide free services to people experiencing or at risk of homelessness. Pharmacists were involved in this initiative and provided health services in a multidisciplinary healthcare environment building on the lessons of previous Homeless Connect events (Chan et al, 2015) Aims. To explore pharmacists reflections on their role in a multidisciplinary healthcare team providing services at a community outreach event for those experiencing homelessness. Methods. The pharmacists (n=2) documented the types of services provided during the Homeless Connect event. A semi-structured interview was conducted post-event to investigate barriers, facilitators and changes that would be recommended for future events. Their perceptions of their role in the multidisciplinary healthcare team were also explored. Results. Primarily, the services provided included delivery of primary healthcare, advice on accessing cost effective pharmacy services and addressing medication enquiries. The pharmacists also provided moisturiser samples and health information leaflets. Interdisciplinary referrals were primarily between the pharmacists and podiatrists; no pharmacist-medical practitioner referrals occurred. The pharmacists did believe they had a positive role in this health initiative but improvements could be implemented to improve the delivery of these services in future events. Discussion. Pharmacists can play an important role in providing services to people experiencing or at risk of homelessness and the overall experience was positive for the pharmacists. They were able to integrate into a multidisciplinary healthcare team in this setting but strategies for further collaboration were identified. The possibility of involving pharmacy students in future events was identified.

Evaluation of the Australian branched broomrape (Orobanche ramosa) eradication program

Because weed eradication programs commonly take 10 or more years to complete, there is a need to evaluate progress toward the eradication objective. We present a simple model, based on information that is readily obtainable, that assesses conformity to the delimitation and extirpation criteria for eradication. It is applied to the program currently targeting the annual parasitic weed, branched broomrape, in South Australia. The model consists of delimitation and extirpation (E) measures plotted against each other to form an 'eradograph.' Deviations from the 'ideal' eradograph plot can inform tactical responses, e.g., increases in survey and/or control effort. Infestations progress from the active phase to the monitoring phase when no plants have been detected for at least 12 mo. They revert to the active phase upon further detection of plants. We summarize this process for the invasion as a whole in a state-and-transition model. Using this model we demonstrate that the invasion is unlikely to be delimited unless the amount of newly detected infested area decreases, on average, by at least 50% per annum. As a result of control activities implemented, on average approximately 70% (range, 44 to 86%) of active infestations progressed to the monitoring phase in the year following their detection. Simulations suggest that increasing this rate of transition will not increase E to a significant extent. The rate of reversion of infestations from the monitoring phase to the active phase decreased logarithmically with time since last detection, but it is likely that lower rates of reversion would accelerate the trend toward extirpation. Program performance with respect to the delimitation criterion has been variable; performance with respect to the extirpation criterion would be improved considerably by the development and application of cost-effective methods for eliminating branched broomrape soil seed populations.

The School-Community Integrated Learning pathway: Exploring a new way to prepare and induct final-year preservice teachers

Universities and teacher employment bodies seek new, cost-effective ways for graduating classroom-ready teachers. This study involved 32 final-year preservice teachers in an innovative school-university partnership teacher education program titled, the School-Community Integrated Learning (SCIL) pathway. Data were collected using a five-part Likert scale survey with extended written responses. Survey results showed that preservice teachers involved in the SCIL pathway learnt more about the teaching profession, which extended their usual university coursework. Furthermore, written responses suggested ways for advancing their understandings to ensure preservice teachers receive a quality school experience towards readiness for teaching.

Calotrope (Calotropis procera) control

Calotrope [Calotropis procera (Aiton) W.T.Aiton] is an exotic shrub or small tree species that is currently invading the tropical savannahs of northern Australia. A chemical trial involving 11 herbicides and four application methods (foliar, basal bark, cut stump and soil applied) was undertaken to identify effective chemicals to control calotrope. Of the foliar herbicides tested, imazapyr provided 100% mortality at the rates applied, and the higher rate of metsulfuron-methyl killed 100% of the treated plants. The herbicides 2,4-D butyl ester, fluroxypyr, triclopyr and triclopyr/picloram killed greater than 80% of the plants when applied by a basal bark or cut stump (when cut 5cm above ground level) method of application. Plants cut close to ground level (5cm) were controlled more effectively than plants cut 20cm above ground level. Chemical control (foliar and cut stump spraying) is a cost effective tool to treat calotrope densities <800plants/ha. Adoption of pasture management practices that promote perennial grasses, in conjunction with strategic chemical control, would further increase the effectiveness and reduce the costs of controlling vast areas of this weed.

DArT markers: Diversity analyses and mapping in Sorghum bicolor

The sequential nature of gel-based marker systems entails low throughput and high costs per assay. Commonly used marker systems such as SSR and SNP are also dependent on sequence information. These limitations result in high cost per data point and significantly limit the capacity of breeding programs to obtain sufficient return on investment to justify the routine use of marker-assisted breeding for many traits and particularly quantitative traits. Diversity Arrays Technology (DArT™) is a cost effective hybridisation-based marker technology that offers a high multiplexing level while being independent of sequence information. This technology offers sorghum breeding programs an alternative approach to whole-genome profiling. We report on the development, application, mapping and utility of DArT™ markers for sorghum germplasm. Results: A genotyping array was developed representing approximately 12,000 genomic clones using PstI+BanII complexity with a subset of clones obtained through the suppression subtractive hybridisation (SSH) method. The genotyping array was used to analyse a diverse set of sorghum genotypes and screening a Recombinant Inbred Lines (RIL) mapping population. Over 500 markers detected variation among 90 accessions used in a diversity analysis. Cluster analysis discriminated well between all 90 genotypes. To confirm that the sorghum DArT markers behave in a Mendelian manner, we constructed a genetic linkage map for a cross between R931945-2-2 and IS 8525 integrating DArT and other marker types. In total, 596 markers could be placed on the integrated linkage map, which spanned 1431.6 cM. The genetic linkage map had an average marker density of 1/2.39 cM, with an average DArT marker density of 1/3.9 cM. Conclusion: We have successfully developed DArT markers for Sorghum bicolor and have demonstrated that DArT provides high quality markers that can be used for diversity analyses and to construct medium-density genetic linkage maps. The high number of DArT markers generated in a single assay not only provides a precise estimate of genetic relationships among genotypes, but also their even distribution over the genome offers real advantages for a range of molecular breeding and genomics applications.

Soveltuvuuskokeella täydennetty opiskelijavalinta : Seurantatutkimus eräiden sosiaali- ja terveysalan teknisluonteisten koulutusohjelmien (apuvälinetekniikka, hammastekniikka ja optometria) opiskelijavalinnan toteuttamisesta

Aptitude-based student selection: A study concerning the admission processes of some technically oriented healthcare degree programmes in Finland (Orthotics and Prosthetics, Dental Technology and Optometry). The data studied consisted of conveniencesamples of preadmission information and the results of the admission processes of three technically oriented healthcare degree programmes (Orthotics and Prosthetics, Dental Technology and Optometry) in Finland during the years 1977-1986 and 2003. The number of the subjects tested and interviewed in the first samples was 191, 615 and 606, and in the second 67, 64 and 89, respectively. The questions of the six studies were: I. How were different kinds of preadmission data related to each other? II. Which were the major determinants of the admission decisions? III. Did the graduated students and those who dropped out differ from each other? IV. Was it possible to predict how well students would perform in the programmes? V. How was the student selection executed in the year 2003? VI. Should clinical vs. statistical prediction or both be used? (Some remarks are presented on Meehl's argument: "Always, we might as well face it, the shadow of the statistician hovers in the background; always the actuary will have the final word.") The main results of the study were as follows: Ability tests, dexterity tests and judgements of personality traits (communication skills, initiative, stress tolerance and motivation) provided unique, non-redundant information about the applicants. Available demographic variables did not bias the judgements of personality traits. In all three programme settings, four-factor solutions (personality, reasoning, gender-technical and age-vocational with factor scores) could be extracted by the Maximum Likelihood method with graphical Varimax rotation. The personality factor dominated the final aptitude judgements and very strongly affected the selection decisions. There were no clear differences between graduated students and those who had dropped out in regard to the four factors. In addition, the factor scores did not predict how well the students performed in the programmes. Meehl's argument on the uncertainty of clinical prediction was supported by the results, which on the other hand did not provide any relevant data for rules on statistical prediction. No clear arguments for or against the aptitude-based student selection was presented. However, the structure of the aptitude measures and their impact on the admission process are now better known. The concept of "personal aptitude" is not necessarily included in the values and preferences of those in charge of organizing the schooling. Thus, obviously the most well-founded and cost-effective way to execute student selection is to rely on e.g. the grade point averages of the matriculation examination and/or written entrance exams. This procedure, according to the present study, would result in a student group which has a quite different makeup (60%) from the group selected on the basis of aptitude tests. For the recruiting organizations, instead, "personal aptitude" may be a matter of great importance. The employers, of course, decide on personnel selection. The psychologists, if consulted, are responsible for the proper use of psychological measures.

Assessment of permeable covers for odour reduction in piggery effluent ponds. 1. Laboratory-scale trials

A variety of materials were trialed as supported permeable covers using a series of laboratory-scale anaerobic digesters. Efficacy of cover performance was assessed in terms of impact on odour and greenhouse gas emission rate, and the characteristics of anaerobic liquor. Data were collected over a 12-month period. Initially the covers reduced the rate of odour emission 40-100 times relative to uncovered digesters. After about three months, this decreased to about a threefold reduction in odour emission rate, which was maintained over the remainder of the trial. The covers did not alter methane emission rates. Carbon dioxide emission rates varied according to cover type. Performance of the covers was attributed to the physical characteristics of the cover materials and changes in liquor composition. The reductions in odour emission indicate that these covers offer a cost-effective method for odour control.

Estimating crop area using seasonal time series of enhanced vegetation index from MODIS satellite imagery

Cereal grain is one of the main export commodities of Australian agriculture. Over the past decade, crop yield forecasts for wheat and sorghum have shown appreciable utility for industry planning at shire, state, and national scales. There is now an increasing drive from industry for more accurate and cost-effective crop production forecasts. In order to generate production estimates, accurate crop area estimates are needed by the end of the cropping season. Multivariate methods for analysing remotely sensed Enhanced Vegetation Index (EVI) from 16-day Moderate Resolution Imaging Spectroradiometer (MODIS) satellite imagery within the cropping period (i.e. April-November) were investigated to estimate crop area for wheat, barley, chickpea, and total winter cropped area for a case study region in NE Australia. Each pixel classification method was trained on ground truth data collected from the study region. Three approaches to pixel classification were examined: (i) cluster analysis of trajectories of EVI values from consecutive multi-date imagery during the crop growth period; (ii) harmonic analysis of the time series (HANTS) of the EVI values; and (iii) principal component analysis (PCA) of the time series of EVI values. Images classified using these three approaches were compared with each other, and with a classification based on the single MODIS image taken at peak EVI. Imagery for the 2003 and 2004 seasons was used to assess the ability of the methods to determine wheat, barley, chickpea, and total cropped area estimates. The accuracy at pixel scale was determined by the percent correct classification metric by contrasting all pixel scale samples with independent pixel observations. At a shire level, aggregated total crop area estimates were compared with surveyed estimates. All multi-temporal methods showed significant overall capability to estimate total winter crop area. There was high accuracy at pixel scale (>98% correct classification) for identifying overall winter cropping. However, discrimination among crops was less accurate. Although the use of single-date EVI data produced high accuracy for estimates of wheat area at shire scale, the result contradicted the poor pixel-scale accuracy associated with this approach, due to fortuitous compensating errors. Further studies are needed to extrapolate the multi-temporal approaches to other geographical areas and to improve the lead time for deriving cropped-area estimates before harvest.

Predicting risk and benefit a priori in biological control of invasive plant species: a systems modelling approach

While the method using specialist herbivores in managing invasive plants (classical biological control) is regarded as relatively safe and cost-effective in comparison to other methods of management, the rarity of strict monophagy among insect herbivores illustrates that, like any management option, biological control is not risk-free. The challenge for classical biological control is therefore to predict risks and benefits a priori. In this study we develop a simulation model that may aid in this process. We use this model to predict the risks and benefits of introducing the chrysomelid beetle Charidotis auroguttata to manage the invasive liana Macfadyena unguis-cati in Australia. Preliminary host-specificity testing of this herbivore indicated that there was limited feeding on a non-target plant, although the non-target was only able to sustain some transitions of the life cycle of the herbivore. The model includes herbivore, target and non-target life history and incorporates spillover dynamics of populations of this herbivore from the target to the non-target under a variety of scenarios. Data from studies of this herbivore in the native range and under quarantine were used to parameterize the model and predict the relative risks and benefits of this herbivore when the target and non-target plants co-occur. Key model outputs include population dynamics on target (apparent benefit) and non-target (apparent risk) and fitness consequences to the target (actual benefit) and non-target plant (actual risk) of herbivore damage. The model predicted that risk to the non-target became unacceptable (i.e. significant negative effects on fitness) when the ratio of target to non-target in a given patch ranged from 1:1 to 3:2. By comparing the current known distribution of the non-target and the predicted distribution of the target we were able to identify regions in Australia where the agent may be pose an unacceptable risk. By considering risk and benefit simultaneously, we highlight how such a simulation modelling approach can assist scientists and regulators in making more objective decisions a priori, on the value of releasing specialist herbivores as biological control agents.

Weeds of Australian rangelands

Despite recognition that non-native plant species represent a substantial risk to natural systems, there is currently no compilation of weeds that impact on the biodiversity of the rangelands within Australia. Using published and expert knowledge, this paper presents a list of 622 non-native naturalised species known to occur within the rangelands. Of these, 160 species (26%) are considered a current threat to rangeland biodiversity. Most of these plant species have been deliberately introduced for forage or other commercial use (e.g. nursery trade). Among growth forms, shrubs and perennial grasses comprise over 50% of species that pose the greatest risk to rangeland biodiversity. We identify regions within the rangelands containing both high biodiversity values and a high proportion of weeds and recommend these areas as priorities for weed management. Finally, we examine the resources available for weed detection and identification since detecting weeds in the early stages of invasion is the most cost effective method of reducing further impact.