Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

Using a free online questionnaire to determine the skills, competencies and knowledge required to work in a digital library environment in Australia

This paper discusses the data collection technique used to determine the skills and knowledge required of academic librarians working in a digital library environment in Australia. The research was undertaken as part of the researcher’s master’s thesis conducted at Tallinn University. The data collection instrument used was a freely available online survey tool, and its advantages and disadvantages are discussed in terms of the desired outcomes and circumstances surrounding the thesis project. Decisions regarding the design of the questionnaire are also discussed.

Rapid detection of TNT in aqueous media by selective label free surface enhanced Raman spectroscopy

We report rapid and ultra-sensitive detection system for 2,4,6-trinitrotoluene (TNT) using unmodified gold nanoparticles and surface-enhanced Raman spectroscopy (SERS). First, Meisenheimer complex has been formed in aqueous solution between TNT and cysteamine in less than 15 min of mixing. The complex formation is confirmed by the development of a pink colour and a new UV–vis absorption band around 520 nm. Second, the developed Meisenheimer complex is spontaneously self-assembled onto unmodified gold nanoparticles through a stable Au–S bond between the cysteamine moiety and the gold surface. The developed mono layer of cysteamine-TNT is then screened by SERS to detect and quantify TNT. Our experimental results demonstrate that the SERS-based assay provide an ultra-sensitive approach for the detection of TNT down to 22.7 ng/L. The unambiguous fingerprint identification of TNT by SERS represents a key advantage for our proposed method. The new method provides high selectivity towards TNT over 2,4 DNT and picric acid. Therefore it satisfies the practical requirements for the rapid screening of TNT in real life samples where the interim 24-h average allowable concentration of TNT in waste water is 0.04 mg/L.

Place recognition with ConvNet landmarks: Viewpoint-robust, condition-robust, training-free

Place recognition has long been an incompletely solved problem in that all approaches involve significant compromises. Current methods address many but never all of the critical challenges of place recognition – viewpoint-invariance, condition-invariance and minimizing training requirements. Here we present an approach that adapts state-of-the-art object proposal techniques to identify potential landmarks within an image for place recognition. We use the astonishing power of convolutional neural network features to identify matching landmark proposals between images to perform place recognition over extreme appearance and viewpoint variations. Our system does not require any form of training, all components are generic enough to be used off-the-shelf. We present a range of challenging experiments in varied viewpoint and environmental conditions. We demonstrate superior performance to current state-of-the- art techniques. Furthermore, by building on existing and widely used recognition frameworks, this approach provides a highly compatible place recognition system with the potential for easy integration of other techniques such as object detection and semantic scene interpretation.

A practical guide to terminology for kimberlite facies: A systematic progression from descriptive to genetic, including a pocket guide

Kimberlite terminology remains problematic because both descriptive and genetic terms are mixed together in most existing terminology schemes. In addition, many terms used in existing kimberlite terminology schemes are not used in mainstream volcanology, even though kimberlite bodies are commonly the remains of kimberlite volcanic vents and edifices. We build on our own recently published approach to kimberlite facies terminology, involving a systematic progression from descriptive to genetic. The scheme can be used for both coherent kimberlite (i.e. kimberlite that was emplaced without undergoing any fragmentation processes and therefore preserving coherent igneous textures) and fragmental kimberlites. The approach involves documentation of components, textures and assessing the degree and effects of alteration on both components and original emplacement textures. This allows a purely descriptive composite component, textural and compositional petrological rock or deposit name to be constructed first, free of any biases about emplacement setting and processes. Then important facies features such as depositional structures, contact relationships and setting are assessed, leading to a composite descriptive and genetic name for the facies or rock unit that summarises key descriptive characteristics, emplacement processes and setting. Flow charts summarising the key steps in developing a progressive descriptive to genetic terminology are provided for both coherent and fragmental facies/deposits/rock units. These can be copied and used in the field, or in conjunction with field (e.g. drill core observations) and petrographic data. Because the approach depends heavily on field scale observations, characteristics and process interpretations, only the first descriptive part is appropriate where only petrographic observations are being made. Where field scale observations are available the progression from developing descriptive to interpretative terminology can be used, especially where some petrographic data also becomes available.

The effect of osteoimmunomodulation on the osteogenic effects of cobalt incorporated β-tricalcium phosphate

Osteoblast lineage cells are direct effectors of osteogenesis and are, therefore, commonly used to evaluate the in vitro osteogenic capacity of bone substitute materials. This method has served its purposes when testing novel bone biomaterials; however, inconsistent results between in vitro and in vivo studies suggest the mechanisms that govern a material's capacity to mediate osteogenesis are not well understood. The emerging field of osteoimmunology and immunomodulation has informed a paradigm shift in our view of bone biomaterials–from one of an inert to an osteoimmunomodulatory material–highlighting the importance of immune cells in materials-mediated osteogenesis. Neglecting the importance of the immune response during this process is a major shortcoming of the current evaluation protocol. In this study we evaluated a potential angiogenic bone substitute material cobalt incorporated with β-tricalcium phosphate (CCP), comparing the traditional “one cell type” approach with a “multiple cell types” approach to assess osteogenesis, the latter including the use of immune cells. We found that CCP extract by itself was sufficient to enhance osteogenic differentiation of bone marrow stem cells (BMSCs), whereas this effect was cancelled out when macrophages were involved. In response to CCP, the macrophage phenotype switched to the M1 extreme, releasing pro-inflammatory cytokines and bone catabolic factors. When the CCP materials were implanted into a rat femur condyle defect model, there was a significant increase of inflammatory markers and bone destruction, coupled with fibrous encapsulation rather than new bone formation. These findings demonstrated that the inclusion of immune cells (macrophages) in the in vitro assessment matched the in vivo tissue response, and that this method provides a more accurate indication of the essential role of immune cells when assessing materials-stimulated osteogenesis in vitro.

Reproducible and label-free biosensor for the selective extraction and rapid detection of proteins in biological fluids

Erythropoietin (EPO), a glycoprotein hormone of ∼34 kDa, is an important hematopoietic growth factor, mainly produced in the kidney and controls the number of red blood cells circulating in the blood stream. Sensitive and rapid recombinant human EPO (rHuEPO) detection tools that improve on the current laborious EPO detection techniques are in high demand for both clinical and sports industry. A sensitive aptamer-functionalized biosensor (aptasensor) has been developed by controlled growth of gold nanostructures (AuNS) over a gold substrate (pAu/AuNS). The aptasensor selectively binds to rHuEPO and, therefore, was used to extract and detect the drug from horse plasma by surface enhanced Raman spectroscopy (SERS). Due to the nanogap separation between the nanostructures, the high population and distribution of hot spots on the pAu/AuNS substrate surface, strong signal enhancement was acquired. By using wide area illumination (WAI) setting for the Raman detection, a low RSD of 4.92% over 150 SERS measurements was achieved. The significant reproducibility of the new biosensor addresses the serious problem of SERS signal inconsistency that hampers the use of the technique in the field. The WAI setting is compatible with handheld Raman devices. Therefore, the new aptasensor can be used for the selective extraction of rHuEPO from biological fluids and subsequently screened with handheld Raman spectrometer for SERS based in-field protein detection.

Structural optimization approach for specially shaped composite tank in spacecrafts

This study proposes an optimized approach of designing in which a model specially shaped composite tank for spacecrafts is built by applying finite element analysis. The composite layers are preliminarily designed by combining quasi-network design method with numerical simulation, which determines the ratio between the angle and the thickness of layers as the initial value of the optimized design. By adopting an adaptive simulated annealing algorithm, the angles and the numbers of layers at each angle are optimized to minimize the weight of structure. Based on this, the stacking sequence of composite layers is formulated according to the number of layers in the optimized structure by applying the enumeration method and combining the general design parameters. Numerical simulation is finally adopted to calculate the buckling limit of tanks in different designing methods. This study takes a composite tank with a cone-shaped cylinder body as example, in which ellipsoid head section and outer wall plate are selected as the object to validate this method. The result shows that the quasi-network design method can improve the design quality of composite material layer in tanks with complex preliminarily loading conditions. The adaptive simulated annealing algorithm can reduce the initial design weight by 30%, which effectively probes the global optimal solution and optimizes the weight of structure. It can be therefore proved that, this optimization method is capable of designing and optimizing specially shaped composite tanks with complex loading conditions.

Free Sherlock: The copyright battle of Baker Street

Sherlock Holmes faces his greatest challenge – since his fight to the death with Professor James Moriarty at Reichenbach Falls. Who owns Sherlock Holmes, the world’s greatest detective? Is it the estate of Sir Arthur Conan Doyle? Or the mysterious socialite Andrea Plunket? Or does Sherlock Holmes belong to the public? This is the question currently being debated in copyright litigation in the United States courts, raising larger questions about copyright law and the public domain, the ownership of literary characters, and the role of sequels, adaptations, and mash-ups.

Fossil free Stanford: Universities, climate ethics, and fossil fuel divestment

There has been an international movement led by 350.org, Bill McKibben, and student groups to encourage schools, universities, and educational institutions to divest their endowments of fossil fuel stocks. The decision of Stanford University on coal divestment should an inspiration for elite universities around the world.

From Kafka to KAFTA: Intellectual property, and the Korea-Australia free trade agreement

This paper provides a critical examination of the intellectual property sections of the Korea-Australia Free Trade Agreement 2014. Chapter 13 of the Korea-Australia Free Trade Agreement 2014 deals with the subject of intellectual property law. The Chapter covers such topics as the purposes and objectives of intellectual property law; copyright law; trade mark law; patent law; and intellectual property enforcement. The Joint Standing Committee on Treaties in the Australian Parliament highlighted the controversy surrounding this chapter of the agreement: The intellectual property rights chapter of KAFTA has drawn considerable attention from academics and stakeholders regarding the proposed need for changes to Australian intellectual property law and the inclusion of intellectual property in the definition of investment with regard to the investor-state dispute mechanism. Other concerns raised with the Committee include the prescriptive nature of the chapter, the lack of recognition of the broader public interests of intellectual property rights, and possible changes to fair use provisions. Article 13.1.1 of the Korea-Australia Free Trade Agreement 2014 provides that: ‘Each Party recognises the importance of adequate and effective protection of intellectual property rights, while ensuring that measures to enforce those rights do not themselves become barriers to legitimate trade.’ This is an unsatisfactory description of the objectives and purposes of intellectual property law in both Australia and Korea. There is a failure to properly consider the range of public purposes served by intellectual property law – such as providing for access to knowledge, promoting competition and innovation, protecting consumer rights, and allowing for the protection of public health, food security, and the environment. Such a statement of principles and objectives detracts from the declaration in the TRIPS Agreement 1994 of the public interest objectives to be served by intellectual property. Chapter 11 of the Korea-Australia Free Trade Agreement 2014 is an investment chapter, with an investor-state dispute settlement regime. This chapter is highly controversial – given the international debate over investor-state dispute settlement; the Australian context for the debate; and the text of the Korea-Australia Free Trade Agreement 2014. In April 2014, the United Nations Conference on Trade and Development (UNCTAD) released a report on Recent Developments in Investor-State Dispute Settlement. The overall figures are staggering. UNCTAD reports a significant growth in investment-state dispute settlement, across a wide array of different fields of public regulation. Given the broad definition of investment, intellectual property owners will be able to use the investor-state dispute settlement regime in the Korea-Australia Free Trade Agreement 2014. This will have significant implications for all the various disciplines of intellectual property – including copyright law, trade mark law, and patent law.

Robbery under arms: Copyright law and the Australia-United States free trade agreement

TThis article considers the radical, sweeping changes to Australian copyright law wrought by the Australia–United States Free Trade Agreement 2004 (AUSFTA). It contends that the agreement will result in a “piracy of the public domain”. Under this new regime, copyright owners will be able to obtain greater monopoly profits at the expense of Australian consumers, libraries and research institutions, as well as intermediaries, such as Internet service providers. Part One observes that the copyright term extension in Australia to life of the author plus 70 years for works will have a negative economic and cultural impact — with Australia’s net royalty payments estimated to be up to $88 million higher per year. Part Two argues that the adoption of stronger protection of technological protection measures modelled upon the Digital Millennium Copyright Act 1998 (U.S.) will override domestic policy–making processes, such as the Phillips Fox Digital Agenda Review, and judicial pronouncements such as the Stevens v Sony litigation. Part Three questions whether the new safe harbours protection for Internet service providers will adversely affect the sale of Telstra. This article concludes that there is a need for judicial restraint in interpreting the AUSFTA. There is an urgent call for the Federal Government to pass ameliorating reforms — such as an open–ended defence of fair use and a mechanism for orphan works. There is a need for caution in negotiating future bilateral trade agreements — lest the multinational system for the protection of copyright law be undermined.

The rapid manufacture of uniform composite multicellular-biomaterial micropellets, their assembly into macroscopic organized tissues, and potential applications in cartilage tissue engineering

We and others have published on the rapid manufacture of micropellet tissues, typically formed from 100-500 cells each. The micropellet geometry enhances cellular biological properties, and in many cases the micropellets can subsequently be utilized as building blocks to assemble complex macrotissues. Generally, micropellets are formed from cells alone, however when replicating matrix-rich tissues such as cartilage it would be ideal if matrix or biomaterials supplements could be incorporated directly into the micropellet during the manufacturing process. Herein we describe a method to efficiently incorporate donor cartilage matrix into tissue engineered cartilage micropellets. We lyophilized bovine cartilage matrix, and then shattered it into microscopic pieces having average dimensions < 10 μm diameter; we termed this microscopic donor matrix "cartilage dust (CD)". Using a microwell platform, we show that ~0.83 μg CD can be rapidly and efficiently incorporated into single multicellular aggregates formed from 180 bone marrow mesenchymal stem/stromal cells (MSC) each. The microwell platform enabled the rapid manufacture of thousands of replica composite micropellets, with each micropellet having a material/CD core and a cellular surface. This micropellet organization enabled the rapid bulking up of the micropellet core matrix content, and left an adhesive cellular outer surface. This morphological organization enabled the ready assembly of the composite micropellets into macroscopic tissues. Generically, this is a versatile method that enables the rapid and uniform integration of biomaterials into multicellular micropellets that can then be used as tissue building blocks. In this study, the addition of CD resulted in an approximate 8-fold volume increase in the micropellets, with the donor matrix functioning to contribute to an increase in total cartilage matrix content. Composite micropellets were readily assembled into macroscopic cartilage tissues; the incorporation of CD enhanced tissue size and matrix content, but did not enhance chondrogenic gene expression.

Multifunctional SA-PProDOT binder for lithium ion batteries

An environmentally benign, highly conductive, and mechanically strong binder system can overcome the dilemma of low conductivity and insufficient mechanical stability of the electrodes to achieve high performance lithium ion batteries (LIBs) at a low cost and in a sustainable way. In this work, the naturally occurring binder sodium alginate (SA) is functionalized with 3,4-propylenedioxythiophene-2,5-dicarboxylic acid (ProDOT) via a one-step esterification reaction in a cyclohexane/dodecyl benzenesulfonic acid (DBSA)/water microemulsion system, resulting in a multifunctional polymer binder, that is, SA-PProDOT. With the synergetic effects of the functional groups (e.g., carboxyl, hydroxyl, and ester groups), the resultant SA-PProDOT polymer not only maintains the outstanding binding capabilities of sodium alginate but also enhances the mechanical integrity and lithium ion diffusion coefficient in the LiFePO4 (LFP) electrode during the operation of the batteries. Because of the conjugated network of the PProDOT and the lithium doping under the battery environment, the SA-PProDOT becomes conductive and matches the conductivity needed for LiFePO4 LIBs. Without the need of conductive additives such as carbon black, the resultant batteries have achieved the theoretical specific capacity of LiFePO4 cathode (ca. 170 mAh/g) at C/10 and ca. 120 mAh/g at 1C for more than 400 cycles.

The effect of graphene oxide and its oxidized debris on the cure chemistry and interphase structure of epoxy nanocomposites

The influence of graphene oxide (GO) and its surface oxidized debris (OD) on the cure chemistry of an amine cured epoxy resin has been investigated by Fourier Transform Infrared Emission Spectroscopy (FT-IES) and Differential Scanning Calorimetry (DSC). Spectral analysis of IR radiation emitted at the cure temperature from thin films of diglycidyl ether of bisphenol A epoxy resin (DGEBA) and 4,4'-diaminodiphenylmethane (DDM) curing agent with and without GO allowed the cure kinetics of the interphase between the bulk resin and GO to be monitored in real time, by measuring both the consumption of primary (1°) amine and epoxy groups, formation of ether groups as well as computing the profiles for formation of secondary (2°) and tertiary (3°) amines. OD was isolated from as-produced GO (aGO) by a simple autoclave method to give OD-free autoclaved GO (acGO). It has been found that the presence of OD on the GO prevents active sites on GO surfaces fully catalysing and participating in the reaction of DGEBA with DDM, which results in slower reaction and a lower crosslink density of the three-dimensional networks in the aGO-resin interphase compared to the acGO-resin interphase. We also determined that OD itself promoted DGEBA homopolymerization. A DSC study further confirmed that the aGO nanocomposite exhibited lower Tg while acGO nanocomposite showed higher Tg compared to neat resin because of the difference in crosslink densities of the matrix around the different GOs.