Testing Platform Development for Large Scale Solar Integration

Currently, a high penetration level of Distributed Generations (DGs) has been observed in the Danish distribution systems, and even more DGs are foreseen to be present in the upcoming years. How to utilize them for maintaining the security of the power supply under the emergency situations, has been of great interest for study. This master project is intended to develop a control architecture for studying purposes of distribution systems with large scale integration of solar power. As part of the EcoGrid EU Smart Grid project, it focuses on the system modelling and simulation of a Danish representative LV network located in Bornholm island. Regarding the control architecture, two types of reactive control techniques are implemented and compare. In addition, a network voltage control based on a tap changer transformer is tested. The optimized results after applying a genetic algorithm to five typical Danish domestic loads are lower power losses and voltage deviation using Q(U) control, specially with large consumptions. Finally, a communication and information exchange system is developed with the objective of regulating the reactive power and thereby, the network voltage remotely and real-time. Validation test of the simulated parameters are performed as well.

Testing pigs of non-technified rearing farms for serum antibodies against Taenia solium in a region of the state of São Paulo, Brazil

Abstract: Taenia solium is a zoonotic tapeworm of great importance in developing countries, due to the occurrence of human taeniasis and cysticercosis. Pigs have an important role in the biological cycle of the parasite as intermediate hosts. The scientific literature has been describing risk factors associated with the occurrence of this disease that must be avoided in countries with poor sanitation, in order to reduce the exposure of swine to the parasite eggs. This research focused on testing pigs of non-technified rearing farms for serum antibodies against Taenia solium in the region of Jaboticabal municipality, in the state of São Paulo, Brazil. The found prevalence was 6.82% (CI 95% 4.18 - 9.45) at animal level and 28.87% (CI 95% 16.74 - 40.40) at herd level. These figures are probably associated with low technification adoption during animal rearing in the studied area, which increased the exposure of the animals to risk factors associated with the occurrence of Taenia solium complex. The results found based on serological evidences of swine cysticercosis in the studied region serves as a warning to public sanitary authorities to improve public health and control T. solium.

Testing and simulation of fractionary electromechanical rotative drives

This paper concerns the development of drives that use electromechanical rotative motor systems. It is proposed an experimental drive test structure integrated to simulation softwares. The objective of this work is to show that an affordable model validation procedure can be obtained by combining a precision data acquisition with well tuned state-of-the-art simulation packages. This is required for fitting, in the best way, a drive to its load or, inversely, to adapt loads to given drive characteristics.

Design and testing of an armature-reaction-compensated permanent magnet synchronous generator for island operation

At present, permanent magnet synchronous generators (PMSGs) are of great interest. Since they do not have electrical excitation losses, the highly efficient, lightweight and compact PMSGs equipped with damper windings work perfectly when connected to a network. However, in island operation, the generator (or parallel generators) alone is responsible for the building up of the network and maintaining its voltage and reactive power level. Thus, in island operation, a PMSG faces very tight constraints, which are difficult to meet, because the flux produced by the permanent magnets (PMs) is constant and the voltage of the generator cannot be controlled. Traditional electrically excited synchronous generators (EESGs) can easily meet these constraints, because the field winding current is controllable. The main drawback of the conventional EESG is the relatively high excitation loss. This doctoral thesis presents a study of an alternative solution termed as a hybrid excitation synchronous generator (HESG). HESGs are a special class of electrical machines, where the total rotor current linkage is produced by the simultaneous action of two different excitation sources: the electrical and permanent magnet (PM) excitation. An overview of the existing HESGs is given. Several HESGs are introduced and compared with the conventional EESG from technical and economic points of view. In the study, the armature-reaction-compensated permanent magnet synchronous generator with alternated current linkages (ARC-PMSG with ACL) showed a better performance than the other options. Therefore, this machine type is studied in more detail. An electromagnetic design and a thermal analysis are presented. To verify the operation principle and the electromagnetic design, a down-sized prototype of 69 kVA apparent power was built. The experimental results are demonstrated and compared with the predicted ones. A prerequisite for an ARC-PMSG with ACL is an even number of pole pairs (p = 2, 4, 6, …) in the machine. Naturally, the HESG technology is not limited to even-pole-pair machines. However, the analysis of machines with p = 3, 5, 7, … becomes more complicated, especially if analytical tools are used, and is outside the scope of this thesis. The contribution of this study is to propose a solution where an ARC-PMSG replaces an EESG in electrical power generation while meeting all the requirements set for generators given for instance by ship classification societies, particularly as regards island operation. The maximum power level when applying the technology studied here is mainly limited by the economy of the machine. The larger the machine is, the smaller is the efficiency benefit. However, it seems that machines up to ten megawatts of power could benefit from the technology. However, in low-power applications, for instance in the 500 kW range, the efficiency increase can be significant.

Intended Quality: Relationships between Development, Testing and Quality

An empirical study was conducted in the area of software engineering to study relationships between development, testing and intended software quality. International standards served as a starting point of the study. For analysis a round of interviews was kept and transcribed. It was found that interaction between humans is critical, especially in transferring knowledge and standards’ processes. The standards are communicated through interaction and learning processes are involved before compliance. One of the results was that testing is the key to sufficient quality. The outcome was that successful interaction, sufficient testing and compliance with the standards combined with good motivation may provide most repeatable intended quality.

Empirical study on the adoption, use and effects of cloud-based testing

Cloud computing is a practically relevant paradigm in computing today. Testing is one of the distinct areas where cloud computing can be applied. This study addressed the applicability of cloud computing for testing within organizational and strategic contexts. The study focused on issues related to the adoption, use and effects of cloudbased testing. The study applied empirical research methods. The data was collected through interviews with practitioners from 30 organizations and was analysed using the grounded theory method. The research process consisted of four phases. The first phase studied the definitions and perceptions related to cloud-based testing. The second phase observed cloud-based testing in real-life practice. The third phase analysed quality in the context of cloud application development. The fourth phase studied the applicability of cloud computing in the gaming industry. The results showed that cloud computing is relevant and applicable for testing and application development, as well as other areas, e.g., game development. The research identified the benefits, challenges, requirements and effects of cloud-based testing; and formulated a roadmap and strategy for adopting cloud-based testing. The study also explored quality issues in cloud application development. As a special case, the research included a study on applicability of cloud computing in game development. The results can be used by companies to enhance the processes for managing cloudbased testing, evaluating practical cloud-based testing work and assessing the appropriateness of cloud-based testing for specific testing needs.

Modal testing and numerical modeling of the dynamic properties of layered sheet-steel structure

Recently, due to the increasing total construction and transportation cost and difficulties associated with handling massive structural components or assemblies, there has been increasing financial pressure to reduce structural weight. Furthermore, advances in material technology coupled with continuing advances in design tools and techniques have encouraged engineers to vary and combine materials, offering new opportunities to reduce the weight of mechanical structures. These new lower mass systems, however, are more susceptible to inherent imbalances, a weakness that can result in higher shock and harmonic resonances which leads to poor structural dynamic performances. The objective of this thesis is the modeling of layered sheet steel elements, to accurately predict dynamic performance. During the development of the layered sheet steel model, the numerical modeling approach, the Finite Element Analysis and the Experimental Modal Analysis are applied in building a modal model of the layered sheet steel elements. Furthermore, in view of getting a better understanding of the dynamic behavior of layered sheet steel, several binding methods have been studied to understand and demonstrate how a binding method affects the dynamic behavior of layered sheet steel elements when compared to single homogeneous steel plate. Based on the developed layered sheet steel model, the dynamic behavior of a lightweight wheel structure to be used as the structure for the stator of an outer rotor Direct-Drive Permanent Magnet Synchronous Generator designed for high-power wind turbines is studied.

Expectations, frames and practices of genetic counselling in different contexts of genetic testing

Genetic counselling is a process in which the counsellee receives information and support concerning a genetic disease. This study examines the genetic counselling attached to genetic testing. Since genetic information is increasing alongside new testing technologies and the situations faced at the genetic clinics will therefore be more diverse, it is essential to assess what the expectations directed at genetic counselling are. It is also important to compare how they face the current counselling practices. In this study, the expectations, frames and practices of genetic counselling in different contexts of genetic testing were examined from three different perspectives: First, international guidelines covering genetic counselling were analysed to summarise what is expected from genetic counselling and to study how genetic information is framed. Second, national experts in European countries were asked about the regulations and practices of genetic counselling in their country. Finally, ten counsellees who had visited a genetic clinic were interviewed to analyse their expectations and experiences. The counsellees’ perspective was also approached through the background review of the previous studies on counsellees’ experiences. On the basis of the study, there are basic elements that are expected to be covered in genetic counselling from all perspectives. However, the views concerning bioethics, genetic exceptionalism and psychosocial aspects vary depending on the perspective and on the individual situation. Since there are sometimes more differences than similarities between genetic tests, no universal recommendations for counselling can be applied. The practices of genetic counselling should be defined situationally, emphasising the individual needs over the genes.

Cardiac Troponin Specific Autoantibodies: Analytical Tools for Exploring Their Impact on Cardiac Troponin I Testing

Cardiac troponin (cTn) I and T are the recommended biomarkers for the diagnosis and risk stratification of patients with suspected acute coronary syndrome (ACS), a major cause of cardiovascular death and disability worldwide. It has recently been demonstrated that cTn-specific autoantibodies (cTnAAb) can negatively interfere with cTnI detection by immunoassays to the extent that cTnAAb-positive patients may be falsely designated as cTnI-negative. The aim of this thesis was to develop and optimize immunoassays for the detection of both cTnI and cTnAAb, which would eventually enable exploring the clinical impact of these autoantibodies on cTnI testing and subsequent patient management. The extent of cTnAAb interference in different cTnI assay configurations and the molecular characteristics of cTnAAbs were investigated in publications I and II, respectively. The findings showed that cTnI midfragment targeting immunoassays used predominantly in clinical practice are affected by cTnAAb interference which can be circumvented by using a novel 3+1-type assay design with three capture antibodies against the N-terminus, midfragment and C-terminus and one tracer antibody against the C-terminus. The use of this assay configuration was further supported by the epitope specificity study, which showed that although the midfragment is most commonly targeted by cTnAAbs, the interference basically encompasses the whole molecule, and there may be remarkable individual variation at the affected sites. In publications III and IV, all the data obtained in previous studies were utilized to develop an improved version of an existing cTnAAb assay and a sensitive cTnI assay free of this specific analytical interference. The results of the thesis showed that approximately one in 10 patients with suspected ACS have detectable amounts of cTnAAbs in their circulation and that cTnAAbs can inhibit cTnI determination when targeted against the binding sites of assay antibodies used in its immunological detection. In the light of these observations, the risk of clinical misclassification caused by the presence of cTnAAbs remains a valid and reasonable concern. Because the titers, affinities and epitope specificities of cTnAAbs and the concentration of endogenous cTnI determine the final effect of circulating cTnAAbs, appropriately sized studies on their clinical significance are warranted. The new cTnI and cTnAAb assays could serve as analytical tools for establishing the impact of cTnAAbs on cTnI testing and also for unraveling the etiology of cTn-related autoimmune responses.

Combined selection in early generation testing of self-pollinated plants

Seven selection indexes based on the phenotypic value of the individual and the mean performance of its family were assessed for their application in breeding of self-pollinated plants. There is no clear superiority from one index to another although some show one or more negative aspects, such as favoring the selection of a top performing plant from an inferior family in detriment of an excellent plant from a superior family

Testing FCM technique for the wind energy scenarios in Finland

In the latter days, human activities constantly increase greenhouse gases emissions in the atmosphere, which has a direct impact on a global climate warming. Finland as European Union member, developed national structural plan to promote renewable energy generation, pursuing the aspects of Directive 2009/28/EC and put it on the sharepoint. Finland is on a way of enhancing national security of energy supply, increasing diversity of the energy mix. There are plenty significant objectives to develop onshore and offshore wind energy generation in country for a next few decades, as well as another renewable energy sources. To predict the future changes, there are a lot of scenario methods developed and adapted to energy industry. The Master’s thesis explored “Fuzzy cognitive maps” approach in scenarios developing, which captures expert’s knowledge in a graphical manner and using these captures for a raw scenarios testing and refinement. There were prospects of Finnish wind energy development for the year of 2030 considered, with aid of FCM technique. Five positive raw scenarios were developed and three of them tested against integrated expert’s map of knowledge, using graphical simulation. The study provides robust scenarios out of the preliminary defined, as outcome, assuming the impact of results, taken after simulation. The thesis was conducted in such way, that there will be possibilities to use existing knowledge captures from expert panel, to test and deploy different sets of scenarios regarding to Finnish wind energy development.

Virtual Testing of Active Magnetic Bearing Systems based on Design Guidelines given by the Standards

Active Magnetic Bearings offer many advantages that have brought new applications to the industry. However, similarly to all new technology, active magnetic bearings also have downsides and one of those is the low standardization level. This thesis is studying mainly the ISO 14839 standard and more specifically the system verification methods. These verifying methods are conducted using a practical test with an existing active magnetic bearing system. The system is simulated with Matlab using rotor-bearing dynamics toolbox, but this study does not include the exact simulation code or a direct algebra calculation. However, this study provides the proof that standardized simulation methods can be applied in practical problems.

Testing Accrual-Based Model for Detecting Earnings Management: Comparison of Finland and France

The aim of this study is to test the accrual-based model suggested by Dechow et al. (1995) in order to detect and compare earnings management practices in Finnish and French companies. Also the impact of financial crisis of 2008 on earnings management behavior in these countries is tested by dividing the whole time period of 2003-2012 into two sub-periods: pre-crisis (2003-2008) and post-crisis (2009-2012). Results support the idea that companies in both countries have significant earnings management practices. During the post-crisis period companies in Finland show income inflating practices, while in France the opposite tendency is noticed (income deflating) during the same period. Results of the assumption that managers in highly concentrated companies are engaged in income enhancing practices vary in two countries. While in Finland managers are trying to show better performance for bonuses or other contractual compensation motivations, in France they avoid paying dividends or high taxes.

Hepatic capillariasis in rats: a new model for testing antifibrotic drugs

Rats infected with the helminth Capillaria hepatica regularly develop septal hepatic fibrosis that may progress to cirrhosis in a relatively short time. Because of such characteristics, this experimental model was selected for testing drugs exhibiting antifibrosis potential, such as pentoxifylline, gadolinium chloride and vitamin A. Hepatic fibrosis was qualitatively and quantitatively evaluated in liver samples obtained by partial hepatectomy and at autopsy. The material was submitted to histological, biochemical and morphometric methods. A statistically significant reduction of fibrosis was obtained with pentoxifylline when administered intraperitoneally rather than intravenously. Gadolinium chloride showed moderate activity when administered prophylactically (before fibrosis had started), but showed a poor effect when fibrosis was well advanced. No modification of fibrosis was seen after vitamin A administration. Hydroxyproline content was correlated with morphometric measurements. The model appears to be adequate, since few animals die of the infection, fibrosis develops regularly in all animals, and the effects of different antifibrotic drugs and administration protocols can be easily detected.