Novel Inductor‐less Conversion Strategy Based on Multiphase Transformer‐Coupled Converters: Analysis, Design and Applications

There are many the requirements that modern power converters should fulfill. Most of the applications where these converters are used, demand smaller converters with high efficiency, improved power density and a fast dynamic response. For instance, loads like microprocessors demand aggressive current steps with very high slew rates (100A/mus and higher); besides, during these load steps, the supply voltage of the microprocessor should be kept within tight limits in order to ensure its correct performance. The accomplishment of these requirements is not an easy task; complex solutions like advanced topologies - such as multiphase converters- as well as advanced control strategies are often needed. Besides, it is also necessary to operate the converter at high switching frequencies and to use capacitors with high capacitance and low ESR. Improving the dynamic response of power converters does not rely only on the control strategy but also the power topology should be suited to enable a fast dynamic response. Moreover, in later years, a fast dynamic response does not only mean accomplishing fast load steps but output voltage steps are gaining importance as well. At least, two applications that require fast voltage changes can be named: Low power microprocessors. In these devices, the voltage supply is changed according to the workload and the operating frequency of the microprocessor is changed at the same time. An important reduction in voltage dependent losses can be achieved with such changes. This technique is known as Dynamic Voltage Scaling (DVS). Another application where important energy savings can be achieved by means of changing the supply voltage are Radio Frequency Power Amplifiers. For example, RF architectures based on ‘Envelope Tracking’ and ‘Envelope Elimination and Restoration’ techniques can take advantage of voltage supply modulation and accomplish important energy savings in the power amplifier. However, in order to achieve these efficiency improvements, a power converter with high efficiency and high enough bandwidth (hundreds of kHz or even tens of MHz) is necessary in order to ensure an adequate supply voltage. The main objective of this Thesis is to improve the dynamic response of DC-DC converters from the point of view of the power topology. And the term dynamic response refers both to the load steps and the voltage steps; it is also interesting to modulate the output voltage of the converter with a specific bandwidth. In order to accomplish this, the question of what is it that limits the dynamic response of power converters should be answered. Analyzing this question leads to the conclusion that the dynamic response is limited by the power topology and specifically, by the filter inductance of the converter which is found in series between the input and the output of the converter. The series inductance is the one that determines the gain of the converter and provides the regulation capability. Although the energy stored in the filter inductance enables the regulation and the capability of filtering the output voltage, it imposes a limitation which is the concern of this Thesis. The series inductance stores energy and prevents the current from changing in a fast way, limiting the slew rate of the current through this inductor. Different solutions are proposed in the literature in order to reduce the limit imposed by the filter inductor. Many publications proposing new topologies and improvements to known topologies can be found in the literature. Also, complex control strategies are proposed with the objective of improving the dynamic response in power converters. In the proposed topologies, the energy stored in the series inductor is reduced; examples of these topologies are Multiphase converters, Buck converter operating at very high frequency or adding a low impedance path in parallel with the series inductance. Control techniques proposed in the literature, focus on adjusting the output voltage as fast as allowed by the power stage; examples of these control techniques are: hysteresis control, V 2 control, and minimum time control. In some of the proposed topologies, a reduction in the value of the series inductance is achieved and with this, the energy stored in this magnetic element is reduced; less stored energy means a faster dynamic response. However, in some cases (as in the high frequency Buck converter), the dynamic response is improved at the cost of worsening the efficiency. In this Thesis, a drastic solution is proposed: to completely eliminate the series inductance of the converter. This is a more radical solution when compared to those proposed in the literature. If the series inductance is eliminated, the regulation capability of the converter is limited which can make it difficult to use the topology in one-converter solutions; however, this topology is suitable for power architectures where the energy conversion is done by more than one converter. When the series inductor is eliminated from the converter, the current slew rate is no longer limited and it can be said that the dynamic response of the converter is independent from the switching frequency. This is the main advantage of eliminating the series inductor. The main objective, is to propose an energy conversion strategy that is done without series inductance. Without series inductance, no energy is stored between the input and the output of the converter and the dynamic response would be instantaneous if all the devices were ideal. If the energy transfer from the input to the output of the converter is done instantaneously when a load step occurs, conceptually it would not be necessary to store energy at the output of the converter (no output capacitor COUT would be needed) and if the input source is ideal, the input capacitor CIN would not be necessary. This last feature (no CIN with ideal VIN) is common to all power converters. However, when the concept is actually implemented, parasitic inductances such as leakage inductance of the transformer and the parasitic inductance of the PCB, cannot be avoided because they are inherent to the implementation of the converter. These parasitic elements do not affect significantly to the proposed concept. In this Thesis, it is proposed to operate the converter without series inductance in order to improve the dynamic response of the converter; however, on the other side, the continuous regulation capability of the converter is lost. It is said continuous because, as it will be explained throughout the Thesis, it is indeed possible to achieve discrete regulation; a converter without filter inductance and without energy stored in the magnetic element, is capable to achieve a limited number of output voltages. The changes between these output voltage levels are achieved in a fast way. The proposed energy conversion strategy is implemented by means of a multiphase converter where the coupling of the phases is done by discrete two-winding transformers instead of coupledinductors since transformers are, ideally, no energy storing elements. This idea is the main contribution of this Thesis. The feasibility of this energy conversion strategy is first analyzed and then verified by simulation and by the implementation of experimental prototypes. Once the strategy is proved valid, different options to implement the magnetic structure are analyzed. Three different discrete transformer arrangements are studied and implemented. A converter based on this energy conversion strategy would be designed with a different approach than the one used to design classic converters since an additional design degree of freedom is available. The switching frequency can be chosen according to the design specifications without penalizing the dynamic response or the efficiency. Low operating frequencies can be chosen in order to favor the efficiency; on the other hand, high operating frequencies (MHz) can be chosen in order to favor the size of the converter. For this reason, a particular design procedure is proposed for the ‘inductorless’ conversion strategy. Finally, applications where the features of the proposed conversion strategy (high efficiency with fast dynamic response) are advantageus, are proposed. For example, in two-stage power architectures where a high efficiency converter is needed as the first stage and there is a second stage that provides the fine regulation. Another example are RF power amplifiers where the voltage is modulated following an envelope reference in order to save power; in this application, a high efficiency converter, capable of achieving fast voltage steps is required. The main contributions of this Thesis are the following: The proposal of a conversion strategy that is done, ideally, without storing energy in the magnetic element. The validation and the implementation of the proposed energy conversion strategy. The study of different magnetic structures based on discrete transformers for the implementation of the proposed energy conversion strategy. To elaborate and validate a design procedure. To identify and validate applications for the proposed energy conversion strategy. It is important to remark that this work is done in collaboration with Intel. The particular features of the proposed conversion strategy enable the possibility of solving the problems related to microprocessor powering in a different way. For example, the high efficiency achieved with the proposed conversion strategy enables it as a good candidate to be used for power conditioning, as a first stage in a two-stage power architecture for powering microprocessors.

Survey of architectures and optimizations for wide bandwidth envelope amplifier

In the last years, RF power amplifiers are taking advantage of the switched dc-dc converters to use them in several architectures that may improve the efficiency of the amplifier, keeping a good linearity. The use of linearization techniques such as Envelope Elimination and Restoration(EER) and Envelope Tracking (ET) requires a very fast dc-dc power converter to provide variable voltage supply to the power amplifier but theoretically the efficiency can be much higher than using the classical amplifiers belonging to classes A, B or AB. The purpose of this paper is to analyze the state of the art of the power converters used as envelope amplifiers in this application. The power topologies will be explored and several important parameters such as efficiency, bandwidth will be discussed.

Calidad poscosecha del tomate (Solanum lycopersicum L.) cultivado en sistemas ecológicos de fertilización

Se condujeron cuatro experimentos unifactoriales en condiciones de campo en áreas agrícolas de la Universidad de Granma, en el período comprendido de septiembre/2007 a enero/2010 para determinar el efecto de la aplicación de micorrizas arbusculares, Azotobacter chroococcum y ácidos húmicos sobre la productividad y la calidad poscosecha del tomate (Solanum lycopersicum L.) cv. “Vyta”, sobre un suelo de tipo Fluvisol. La aplicación simple y combinada de las micorrizas arbusculares, el Azotobacter chroococcum y los ácidos húmicos mostró un efecto positivo sobre la productividad de la variedad de tomate estudiada, al obtenerse incrementos significativos de este indicador en comparación con el control (sin aplicación), lográndose los mejores resultados con la combinación Glomus fasciculatum (0,3 kg m-2) + Azotobacter chroococcum (30 L ha-1) + ácidos húmicos (500 mg L-1) con valores de 54,57 t ha-1. Se comprobó además, que los tratamientos con estos bioproductos presentaron contenidos de sólidos solubles totales (SST), carbohidratos solubles totales (CST), vitamina C, porcentaje de materia seca (PMS), firmeza, longitud y anchura de los frutos superiores al control (sin aplicación). Las plantas controles (sin aplicación) significativamente incrementaron la acidez titulable (contenido de ácido cítrico) y la pérdida de peso y redujeron el pH de los frutos del tomate. Los análisis de correlación realizados revelan que existieron correlaciones positivas y significativas entre el contenido de vitamina C, materia seca, sólidos solubles totales, carbohidratos solubles totales, y el pH de los frutos, mientras que la acidez titulable presentó correlaciones negativas y significativas con todas las variables mencionadas anteriormente. Se encontró a su vez un efecto sinérgico en las plantas con la aplicación combinada de estos productos con respecto al control (sin aplicación), expresado en los mayores valores de los parámetros micorrízicos estudiados. ABSTRACT Four unifactorial experiments under field conditions in an agricultural area belonging to the University of Granma from September/2007 to January/2010 aiming to evaluate the effect of arbuscular mycorrhizas, Azotobacter and humic acids on tomato (Solanum lycopersicum L) cv. “Vyta” crop yield and postharvest quality in a Typic Fluvent soil were conducted. The simple and mixed application of arbuscular mycorrhizas, Azotobacter chroococcum and humic acids showed a positive effect on yield and internal postharvest parameters evaluated for the studied tomato variety, achieving significant increases with respect to the control treatment ones. The best results related to crop yield were achieved by combining Glomus fasciculatum (0.3 kg m-2) + Azotobacter chroococcum (30 L ha-1) + humic acids (500 mg L-1) that lead to 54.57 t ha-1. In addition, it was also demonstrated that the treatments under effect of biofertilizers and biostimulants resulted in higher total soluble solids (TSS), total soluble carbohydrates (TSC), vitamin C, dry matter contents (DMC), firmness, length and width of the fruits than the control treatment. The control plants showed significantly increased titrable acidity (citric acid content) and weight loss and reduced pH on the tomato fruits. The conducted correlation analyses revealed that there were significant and positive correlations between vitamin C content, dry matter, total soluble solids, total soluble carbohydrates, and pH of the fruit, while titratable acidity showed significant negative correlations with all variables mentioned above. At the same time, a synergic effect by mixed utilization of these biological products on tomato plants, with respect to control treatment (non-treated), was found regarding the increase of studied mycorrhizal parameters.

High Efficiency Envelope Amplifier based on a Ripple Cancellation Buck Converter. Design, Optimization and Integration in an EER RFPA

Durante los últimos años la tendencia en el sector de las telecomunicaciones ha sido un aumento y diversificación en la transmisión de voz, video y fundamentalmente de datos. Para conseguir alcanzar las tasas de transmisión requeridas, los nuevos estándares de comunicaciones requieren un mayor ancho de banda y tienen un mayor factor de pico, lo cual influye en el bajo rendimiento del amplificador de radiofrecuencia (RFPA). Otro factor que ha influido en el bajo rendimiento es el diseño del amplificador de radiofrecuencia. Tradicionalmente se han utilizado amplificadores lineales por su buen funcionamiento. Sin embargo, debido al elevado factor de pico de las señales transmitidas, el rendimiento de este tipo de amplificadores es bajo. El bajo rendimiento del sistema conlleva desventajas adicionales como el aumento del coste y del tamaño del sistema de refrigeración, como en el caso de una estación base, o como la reducción del tiempo de uso y un mayor calentamiento del equipo para sistemas portátiles alimentados con baterías. Debido a estos factores, se han desarrollado durante las últimas décadas varias soluciones para aumentar el rendimiento del RFPA como la técnica de Outphasing, combinadores de potencia o la técnica de Doherty. Estas soluciones mejoran las prestaciones del RFPA y en algún caso han sido ampliamente utilizados comercialmente como la técnica de Doherty, que alcanza rendimientos hasta del 50% para el sistema completo para anchos de banda de hasta 20MHz. Pese a las mejoras obtenidas con estas soluciones, los mayores rendimientos del sistema se obtienen para soluciones basadas en la modulación de la tensión de alimentación del amplificador de potencia como “Envelope Tracking” o “EER”. La técnica de seguimiento de envolvente o “Envelope Tracking” está basada en la modulación de la tensión de alimentación de un amplificador lineal de potencia para obtener una mejora en el rendimiento en el sistema comparado a una solución con una tensión de alimentación constante. Para la implementación de esta técnica se necesita una etapa adicional, el amplificador de envolvente, que añade complejidad al amplificador de radiofrecuencia. En un amplificador diseñado con esta técnica, se aumentan las pérdidas debido a la etapa adicional que supone el amplificador de envolvente pero a su vez disminuyen las pérdidas en el amplificador de potencia. Si el diseño se optimiza adecuadamente, puede conseguirse un aumento global en el rendimiento del sistema superior al conseguido con las técnicas mencionadas anteriormente. Esta técnica presenta ventajas en el diseño del amplificador de envolvente, ya que el ancho de banda requerido puede ser menor que el ancho de banda de la señal de envolvente si se optimiza adecuadamente el diseño. Adicionalmente, debido a que la sincronización entre la señal de envolvente y de fase no tiene que ser perfecta, el proceso de integración conlleva ciertas ventajas respecto a otras técnicas como EER. La técnica de eliminación y restauración de envolvente, llamada EER o técnica de Kahn está basada en modulación simultánea de la envolvente y la fase de la señal usando un amplificador de potencia conmutado, no lineal y que permite obtener un elevado rendimiento. Esta solución fue propuesta en el año 1952, pero no ha sido implementada con éxito durante muchos años debido a los exigentes requerimientos en cuanto a la sincronización entre fase y envolvente, a las técnicas de control y de corrección de los errores y no linealidades de cada una de las etapas así como de los equipos para poder implementar estas técnicas, que tienen unos requerimientos exigentes en capacidad de cálculo y procesamiento. Dentro del diseño de un RFPA, el amplificador de envolvente tiene una gran importancia debido a su influencia en el rendimiento y ancho de banda del sistema completo. Adicionalmente, la linealidad y la calidad de la señal de transmitida deben ser elevados para poder cumplir con los diferentes estándares de telecomunicaciones. Esta tesis se centra en el amplificador de envolvente y el objetivo principal es el desarrollo de soluciones que permitan el aumento del rendimiento total del sistema a la vez que satisfagan los requerimientos de ancho de banda, calidad de la señal transmitida y de linealidad. Debido al elevado rendimiento que potencialmente puede alcanzarse con la técnica de EER, esta técnica ha sido objeto de análisis y en el estado del arte pueden encontrarse numerosas referencias que analizan el diseño y proponen diversas implementaciones. En una clasificación de alto nivel, podemos agrupar las soluciones propuestas del amplificador de envolvente según estén compuestas de una o múltiples etapas. Las soluciones para el amplificador de envolvente en una configuración multietapa se basan en la combinación de un convertidor conmutado, de elevado rendimiento con un regulador lineal, de alto ancho de banda, en una combinación serie o paralelo. Estas soluciones, debido a la combinación de las características de ambas etapas, proporcionan un buen compromiso entre rendimiento y buen funcionamiento del amplificador de RF. Por otro lado, la complejidad del sistema aumenta debido al mayor número de componentes y de señales de control necesarias y el aumento de rendimiento que se consigue con estas soluciones es limitado. Una configuración en una etapa tiene las ventajas de una mayor simplicidad, pero debido al elevado ancho de banda necesario, la frecuencia de conmutación debe aumentarse en gran medida. Esto implicará un bajo rendimiento y un peor funcionamiento del amplificador de envolvente. En el estado del arte pueden encontrarse diversas soluciones para un amplificador de envolvente en una etapa, como aumentar la frecuencia de conmutación y realizar la implementación en un circuito integrado, que tendrá mejor funcionamiento a altas frecuencias o utilizar técnicas topológicas y/o filtros de orden elevado, que permiten una reducción de la frecuencia de conmutación. En esta tesis se propone de manera original el uso de la técnica de cancelación de rizado, aplicado al convertidor reductor síncrono, para reducir la frecuencia de conmutación comparado con diseño equivalente del convertidor reductor convencional. Adicionalmente se han desarrollado dos variantes topológicas basadas en esta solución para aumentar la robustez y las prestaciones de la misma. Otro punto de interés en el diseño de un RFPA es la dificultad de poder estimar la influencia de los parámetros de diseño del amplificador de envolvente en el amplificador final integrado. En esta tesis se ha abordado este problema y se ha desarrollado una herramienta de diseño que permite obtener las principales figuras de mérito del amplificador integrado para la técnica de EER a partir del diseño del amplificador de envolvente. Mediante el uso de esta herramienta pueden validarse el efecto del ancho de banda, el rizado de tensión de salida o las no linealidades del diseño del amplificador de envolvente para varias modulaciones digitales. Las principales contribuciones originales de esta tesis son las siguientes: La aplicación de la técnica de cancelación de rizado a un convertidor reductor síncrono para un amplificador de envolvente de alto rendimiento para un RFPA linealizado mediante la técnica de EER. Una reducción del 66% en la frecuencia de conmutación, comparado con el reductor convencional equivalente. Esta reducción se ha validado experimentalmente obteniéndose una mejora en el rendimiento de entre el 12.4% y el 16% para las especificaciones de este trabajo. La topología y el diseño del convertidor reductor con dos redes de cancelación de rizado en cascada para mejorar el funcionamiento y robustez de la solución con una red de cancelación. La combinación de un convertidor redactor multifase con la técnica de cancelación de rizado para obtener una topología que proporciona una reducción del cociente entre frecuencia de conmutación y ancho de banda de la señal. El proceso de optimización del control del amplificador de envolvente en lazo cerrado para mejorar el funcionamiento respecto a la solución en lazo abierto del convertidor reductor con red de cancelación de rizado. Una herramienta de simulación para optimizar el proceso de diseño del amplificador de envolvente mediante la estimación de las figuras de mérito del RFPA, implementado mediante EER, basada en el diseño del amplificador de envolvente. La integración y caracterización del amplificador de envolvente basado en un convertidor reductor con red de cancelación de rizado en el transmisor de radiofrecuencia completo consiguiendo un elevado rendimiento, entre 57% y 70.6% para potencias de salida de 14.4W y 40.7W respectivamente. Esta tesis se divide en seis capítulos. El primer capítulo aborda la introducción enfocada en la aplicación, los amplificadores de potencia de radiofrecuencia, así como los principales problemas, retos y soluciones existentes. En el capítulo dos se desarrolla el estado del arte de amplificadores de potencia de RF, describiéndose las principales técnicas de diseño, las causas de no linealidad y las técnicas de optimización. El capítulo tres está centrado en las soluciones propuestas para el amplificador de envolvente. El modo de control se ha abordado en este capítulo y se ha presentado una optimización del diseño en lazo cerrado para el convertidor reductor convencional y para el convertidor reductor con red de cancelación de rizado. El capítulo cuatro se centra en el proceso de diseño del amplificador de envolvente. Se ha desarrollado una herramienta de diseño para evaluar la influencia del amplificador de envolvente en las figuras de mérito del RFPA. En el capítulo cinco se presenta el proceso de integración realizado y las pruebas realizadas para las diversas modulaciones, así como la completa caracterización y análisis del amplificador de RF. El capítulo seis describe las principales conclusiones de la tesis y las líneas futuras. ABSTRACT The trend in the telecommunications sector during the last years follow a high increase in the transmission rate of voice, video and mainly in data. To achieve the required levels of data rates, the new modulation standards demand higher bandwidths and have a higher peak to average power ratio (PAPR). These specifications have a direct impact in the low efficiency of the RFPA. An additional factor for the low efficiency of the RFPA is in the power amplifier design. Traditionally, linear classes have been used for the implementation of the power amplifier as they comply with the technical requirements. However, they have a low efficiency, especially in the operating range of signals with a high PAPR. The low efficiency of the transmitter has additional disadvantages as an increase in the cost and size as the cooling system needs to be increased for a base station and a temperature increase and a lower use time for portable devices. Several solutions have been proposed in the state of the art to improve the efficiency of the transmitter as Outphasing, power combiners or Doherty technique. However, the highest potential of efficiency improvement can be obtained using a modulated power supply for the power amplifier, as in the Envelope Tracking and EER techniques. The Envelope Tracking technique is based on the modulation of the power supply of a linear power amplifier to improve the overall efficiency compared to a fixed voltage supply. In the implementation of this technique an additional stage is needed, the envelope amplifier, that will increase the complexity of the RFPA. However, the efficiency of the linear power amplifier will increase and, if designed properly, the RFPA efficiency will be improved. The advantages of this technique are that the envelope amplifier design does not require such a high bandwidth as the envelope signal and that in the integration process a perfect synchronization between envelope and phase is not required. The Envelope Elimination and Restoration (EER) technique, known also as Kahn’s technique, is based on the simultaneous modulation of envelope and phase using a high efficiency switched power amplifier. This solution has the highest potential in terms of the efficiency improvement but also has the most challenging specifications. This solution, proposed in 1952, has not been successfully implemented until the last two decades due to the high demanding requirements for each of the stages as well as for the highly demanding processing and computation capabilities needed. At the system level, a very precise synchronization is required between the envelope and phase paths to avoid a linearity decrease of the system. Several techniques are used to compensate the non-linear effects in amplitude and phase and to improve the rejection of the out of band noise as predistortion, feedback and feed-forward. In order to obtain a high bandwidth and efficient RFPA using either ET or EER, the envelope amplifier stage will have a critical importance. The requirements for this stage are very demanding in terms of bandwidth, linearity and quality of the transmitted signal. Additionally the efficiency should be as high as possible, as the envelope amplifier has a direct impact in the efficiency of the overall system. This thesis is focused on the envelope amplifier stage and the main objective will be the development of high efficiency envelope amplifier solutions that comply with the requirements of the RFPA application. The design and optimization of an envelope amplifier for a RFPA application is a highly referenced research topic, and many solutions that address the envelope amplifier and the RFPA design and optimization can be found in the state of the art. From a high level classification, multiple and single stage envelope amplifiers can be identified. Envelope amplifiers for EER based on multiple stage architecture combine a linear assisted stage and a switched-mode stage, either in a series or parallel configuration, to achieve a very high performance RFPA. However, the complexity of the system increases and the efficiency improvement is limited. A single-stage envelope amplifier has the advantage of a lower complexity but in order to achieve the required bandwidth the switching frequency has to be highly increased, and therefore the performance and the efficiency are degraded. Several techniques are used to overcome this limitation, as the design of integrated circuits that are capable of switching at very high rates or the use of topological solutions, high order filters or a combination of both to reduce the switching frequency requirements. In this thesis it is originally proposed the use of the ripple cancellation technique, applied to a synchronous buck converter, to reduce the switching frequency requirements compared to a conventional buck converter for an envelope amplifier application. Three original proposals for the envelope amplifier stage, based on the ripple cancellation technique, are presented and one of the solutions has been experimentally validated and integrated in the complete amplifier, showing a high total efficiency increase compared to other solutions of the state of the art. Additionally, the proposed envelope amplifier has been integrated in the complete RFPA achieving a high total efficiency. The design process optimization has also been analyzed in this thesis. Due to the different figures of merit between the envelope amplifier and the complete RFPA it is very difficult to obtain an optimized design for the envelope amplifier. To reduce the design uncertainties, a design tool has been developed to provide an estimation of the RFPA figures of merit based on the design of the envelope amplifier. The main contributions of this thesis are: The application of the ripple cancellation technique to a synchronous buck converter for an envelope amplifier application to achieve a high efficiency and high bandwidth EER RFPA. A 66% reduction of the switching frequency, validated experimentally, compared to the equivalent conventional buck converter. This reduction has been reflected in an improvement in the efficiency between 12.4% and 16%, validated for the specifications of this work. The synchronous buck converter with two cascaded ripple cancellation networks (RCNs) topology and design to improve the robustness and the performance of the envelope amplifier. The combination of a phase-shifted multi-phase buck converter with the ripple cancellation technique to improve the envelope amplifier switching frequency to signal bandwidth ratio. The optimization of the control loop of an envelope amplifier to improve the performance of the open loop design for the conventional and ripple cancellation buck converter. A simulation tool to optimize the envelope amplifier design process. Using the envelope amplifier design as the input data, the main figures of merit of the complete RFPA for an EER application are obtained for several digital modulations. The successful integration of the envelope amplifier based on a RCN buck converter in the complete RFPA obtaining a high efficiency integrated amplifier. The efficiency obtained is between 57% and 70.6% for an output power of 14.4W and 40.7W respectively. The main figures of merit for the different modulations have been characterized and analyzed. This thesis is organized in six chapters. In Chapter 1 is provided an introduction of the RFPA application, where the main problems, challenges and solutions are described. In Chapter 2 the technical background for radiofrequency power amplifiers (RF) is presented. The main techniques to implement an RFPA are described and analyzed. The state of the art techniques to improve performance of the RFPA are identified as well as the main sources of no-linearities for the RFPA. Chapter 3 is focused on the envelope amplifier stage. The three different solutions proposed originally in this thesis for the envelope amplifier are presented and analyzed. The control stage design is analyzed and an optimization is proposed both for the conventional and the RCN buck converter. Chapter 4 is focused in the design and optimization process of the envelope amplifier and a design tool to evaluate the envelope amplifier design impact in the RFPA is presented. Chapter 5 shows the integration process of the complete amplifier. Chapter 6 addresses the main conclusions of the thesis and the future work.

Identification of Degraded Land in the Canary Islands; Tests and Reviews

Degraded Land is an area that either by natural causes (fires, floods, storms or volcanic eruptions) or more by direct or indirect causes of human action, has been altered or modified from its natural state. Restoration is an activity that initiates or accelerates the recovery of an ecosystem. It can be defined as the set of actions taken in order to reverse or reduce the damage caused in the territory. In the case of the Canary Islands there is a high possibility for the territory to suffer processes that degrade the environment, given that the islands are very fragile ecosystems. Added to this they are territories isolated from the continent, which complicates the process of restoring them. In this paper, the different types of common degraded areas in the Canary Islands are identified, as well as the proposed solutions for remediation, such as afforestation of agricultural land or landfill closure and restoration.

Estudio de los factores que condicionan, a escala local, la presencia de Epidendrum rhopalostele (Orchidaceae): Implicaciones para su conservación

El análisis de los factores que determinan el establecimiento y supervivencia de orquídeas epífitas, incluyen: a) las condiciones microambientales de los bosques que las mantienen, b) preferencias por las características de los hospederos donde crecen, c) limitación en la dispersión de semillas, d) interacciones planta-planta, y e) asociaciones micorrízicas para la germinación y resultan esenciales para el desarrollo de estrategias para la conservación y manejo de este grupo de plantas. Este trabajo ha evaluado la importancia de estos factores en Epidendrum rhopalostele, orquídea epífita del bosque de niebla montano, a través de los análisis de los patrones espaciales de los árboles que la portan y de la propia orquídea, a escala de población, estudios de asociación y métodos moleculares. Estos últimos han consistido en el uso de marcadores AFLP para el análisis de la estructura genética de la orquídea y en la secuenciación-clonación de la región ITS para la identificación de los hongos micorrízicos asociados. El objetivo de esta tesis es, por tanto, una mejor comprensión de los factores que condicionan la presencia de orquídeas epífitas en los remanentes de bosque de niebla montano y una evaluación de las implicaciones para la conservación y mantenimiento de sus hábitats y la permanencia de sus poblaciones. El estudio fue realizado en un fragmento de bosque de niebla montano de sucesión secundaria situado al este de la Cordillera Real, en los Andes del sur de Ecuador, a 2250 m.s.n.m y caracterizado por una pendiente marcada, temperatura media anual de 20.8°C y precipitación anual de 2193 mm. En este fragmento se mapearon, identificaron y caracterizaron todos los árboles presentes con DBH > 1 cm y todos los individuos de Epidendrum rhopalostele. Así mismo se tomaron muestras de hoja para obtener ADN de todas las orquídeas registradas y muestras de raíces de individuos con flor de E. rhopalostele, uno por cada forófito, para el análisis filogenético de micorrizas. Análisis espaciales de patrones de puntos basados en la K de Ripley y la distancia al vecino más cercano fueron usados para los árboles, forófitos y la población de E. rhopalostele. Se observó que la distribución espacial de árboles y forófitos de E. rhopalostele no es aleatoria, ya que se ajusta a un proceso agregado de Poisson. De ahí se infiere una limitación en la dispersión de las semillas en el fragmento estudiado y en el establecimiento de la orquídea. El patrón de distribución de la población de E. rhopalostele en el fragmento muestra un agrupamiento a pequeña escala sugiriendo una preferencia por micro-sitios para el establecimiento de la orquídea con un kernel de dispersión de las semillas estimado de 0.4 m. Las características preferentes del micro-sitio como tipos de árboles (Clusia alata y árboles muertos), tolerancia a la sombra, corteza rugosa, distribución en los dos primeros metros sugieren una tendencia a distribuirse en el sotobosque. La existencia de una segregación espacial entre adultos y juveniles sugiere una competencia por recursos limitados condicionada por la preferencia de micro-sitio. La estructura genética de la población de E. rhopalostele analizada a través de Structure y PCoA evidencia la presencia de dos grupos genéticos coexistiendo en el fragmento y en los mismos forófitos, posiblemente por eventos de hibridización entre especies de Epidendrum simpátricas. Los resultados del análisis de autocorrelación espacial efectuados en GenAlex confirman una estructura genético-espacial a pequeña escala que es compatible con un mecanismo de dispersión de semillas a corta distancia ocasionada por gravedad o pequeñas escorrentías, frente a la dispersión a larga distancia promovida por el viento generalmente atribuida a las orquídeas. Para la identificación de los micobiontes se amplificó la región ITS1-5.8S-ITS2, y 47 secuencias fueron usadas para el análisis filogenético basado en neighborjoining, análisis bayesiano y máximum-likelihood que determinó que Epidendrum rhopalostele establece asociaciones micorrízicas con al menos dos especies diferentes de Tulasnella. Se registraron plantas que estaban asociadas con los dos clados de hongos encontrados, sugiriendo ausencia de limitación en la distribución del hongo. Con relación a las implicaciones para la conservación in situ resultado de este trabajo se recomienda la preservación de todo el fragmento de bosque así como de las interacciones existentes (polinizadores, micorrizas) a fin de conservar la diversidad genética de esta orquídea epífita. Si fuere necesaria una reintroducción se deben contemplar distancias entre los individuos en cada forófito dentro de un rango de 0.4 m. Para promover el reclutamiento y regeneración de E. rhopalostele, se recomienda que los forófitos correspondan preferentemente a árboles muertos o caídos y a especies, como Clusia alata, que posean además corteza rugosa, sean tolerantes a la sombra, y en el área del sotobosque con menor luminosidad. Además es conveniente que las orquídeas en su distribución vertical estén ubicadas en los primeros metros. En conclusión, la limitación en la dispersión, las características del micro-sitio, las interacciones intraespecíficas y con especies congenéricas simpátricas y las preferencias micorrízicas condicionan la presencia de esta orquídea epífita en este tipo de bosque. ABSTRACT The analysis of factors that determine the establishment and survival of epiphytic depends on factors such as a) microenvironmental conditions of forest, b) preference for host characteristics where orchids grow, c) seed dispersal limitation, d) plant-plant interaction, e) priority mycorrhizal associations for germination, are essential for the development of strategies for management and conservation. This work evaluated the importance of these factors in Epidendrum rhopalostele, an epiphytic orchid of montane cloud forest through the analysis of spatial patterns of host trees and the orchid, in a more specific scale, with association studies and molecular methods, including AFLPs for orchid population genetic structure and the sequencing of the ITS region for associated mycorrhizal fungi. The aim of this thesis is to understand the factors that condition the presence of epiphytic orchids in the remnants of montane cloud forest and to assess the implications for the conservation and preservation of their habitats and the persistence of the orchid populations. The study was carried out in a fragment of montane cloud forest of secondary succession on the eastern slope of Cordillera Real in the Andes of southern Ecuador, located at 2250 m a.s.l. characterized by a steep slope, mean annual temperature of 20.8°C and annual precipitation of 2193 mm. All trees with DBH > 1 cm were mapped, characterized and identified. All E. rhopalostele individuals present were counted, marked, characterized and mapped. Leaf samples of all orchid individuals were collected for DNA analysis. Root samples of flowering E. rhopalostele individuals were collected for phylogenetic analysis of mycorrhizae, one per phorophyte. Spatial point pattern analysis based on Ripley`s K function and nearest neighbor function was used for trees, phorophytes and orchid population. We observed that spatial distribution of trees and phorophytes is not random, as it adjusts to a Poisson cluster process. This suggests a limitation for seed dispersal in the study fragment that is affecting orchid establishment. Furthermore, the small-scale spatial pattern of E. rhopalostele evidences a clustering that suggests a microsite preference for orchid establishment with a dispersal kernel of 0.4 m. Microsite features such as types of trees (dead trees or Clusia alata), shade tolerance trees, rough bark, distribution in the first meters suggest a tendency to prefer the understory for their establishment. Regarding plant-plant interaction a spatial segregation between adults and juveniles was present suggesting competition for limited resources conditioned for a microsite preference. Analysis of genetic structure of E. rhopalostele population through Structure and PCoA shows two genetic groups coexisting in this fragment and in the same phorophyte, possibly as a result of hybridization between sympatric species of Epidendrum. Our results of spatial autocorrelation analysis develop in GenAlex confirm a small-scale spatial-genetic structure within the genetic groups that is compatible with a short-distance dispersal mechanism caused by gravity or water run-off, instead of the long-distance seed dispersal promoted by wind generally attributed to orchids. For mycobionts identification ITS1-5.8S-ITS2 rDNA region was amplified. Phylogenetic analysis was performed with neighborjoining, Bayesian likelihood and maximum-likelihood for 47 sequences yielded two Tulasnella clades. This orchid establishes mycorrhizal associations with at least two different Tulasnella species. In some cases both fungi clades were present in same root, suggesting no limitation in fungal distribution. Concerning the implications for in situ conservation resulting from this work, the preservation of all forest fragment and their interactions (pollinators, mycorrhiza) is recommended to conserve the genetic diversity of this species. If a reintroduction were necessary, distances between individuals in each phorophyte within a range of 0.4 m, are recommended. To promote recruitment and regeneration of E. rhopalostele it is recommended that phorophytes correspond to dead or fallen trees or species, such as Clusia alata. Trees that have rough bark and are shade tolerant are also recommended. Furthermore, regarding vertical distribution, it is also convenient that orchids are located in the first meter (in understory, area with less light). In conclusion, limitation on seed dispersal, microsite characteristics, plant-plant interactions or interaction with cogeneric sympatric species and mycorrhizal preferences conditioned the presence of this epiphytic orchid in this fragment forest.

Use of tomato and cucumber horticulture by-products in goat diets: effects o nrumen fermentation and microbial communities in batch and continuous cultures

Two in vitro experiments were conducted to analyse the effects of replacing dietary barley grain with wastes of tomato and cucumber fruits and a 1 : 1 tomato : cucumber mixture on rumen fermentation characteristics and microbial abundance. The control (CON) substrate contained 250 g/kg of barley grain on a dry matter (DM) basis, and another 15 substrates were formulated by replacing 50, 100, 150, 200 or 250 g of barley grain/kg with the same amount (DM basis) of tomato or cucumber fruits or 1 : 1 tomato : cucumber mixture. In Expt 1, all substrates were incubated in batch cultures with rumen micro-organisms from goats for 24 h. Increasing amounts of tomato, cucumber and the mixture of both fruits in the substrate increased final pH and gas production, without changes in final ammonia-nitrogen (NH3-N) concentrations, substrate degradability and total volatile fatty acid (VFA) production, indicating that there were no detrimental effects of any waste fruits on rumen fermentation. Therefore, in Expt 2 the substrates including 250 g of waste fruits (T250, C250 and M250 for tomato, cucumber and the mixture of both fruits, respectively) and the CON substrate were incubated in single-flow continuous-culture fermenters for 8 days. Total VFA production did not differ among substrates, but there were differences in VFA profile. Molar proportions of propionate, isobutyrate and isovalerate were lower and acetate : propionate ratio was greater for T250 compared with CON substrate. Fermentation of substrates containing cucumber (C250 and M250) resulted in lower proportions of acetate, isobutyrate and isovalerate and acetate : propionate ratio, but greater butyrate proportions than the CON substrate. Carbohydrate degradability and microbial N synthesis tended to be lower for substrates containing cucumber than for the CON substrate, but there were no differences between CON and T250 substrates. Abundance of total bacteria, Fibrobacter succinogenes and Ruminococcus flavefaciens, fungi, methanogenic archaea and protozoa were similar in fermenters fed T250 and CON substrates, but fermenters fed C250 and M250 substrates had lower abundances of R. flavefaciens, fungi and protozoa than those fed the CON substrate. Results indicated that tomato fruits could replace dietary barley grain up to 250 g/kg of substrate DM without noticeable effects on rumen fermentation and microbial populations, but the inclusion of cucumber fruits at 250 g/kg of substrate DM negatively affected some microbial populations as it tended to reduce microbial N synthesis and changed the VFA profile. More studies are needed to identify the dietary inclusion level of cucumber which produces no detrimental effects on rumen fermentation and microbial growth.

Compositional differences within and between eukaryotic genomes

Eukaryotic genome similarity relationships are inferred using sequence information derived from large aggregates of genomic sequences. Comparisons within and between species sample sequences are based on the profile of dinucleotide relative abundance values (The profile is ρ*XY = f*XY/f*Xf*Y for all XY, where f*X denotes the frequency of the nucleotide X and f*XY denotes the frequency of the dinucleotide XY, both computed from the sequence concatenated with its inverted complement). Previous studies with respect to prokaryotes and this study document that profiles of different DNA sequence samples (sample size ≥50 kb) from the same organism are generally much more similar to each other than they are to profiles from other organisms, and that closely related organisms generally have more similar profiles than do distantly related organisms. On this basis we refer to the collection {ρ*XY} as the genome signature. This paper identifies ρ*XY extremes and compares genome signature differences for a diverse range of eukaryotic species. Interpretations on the mechanisms maintaining these profile differences center on genome-wide replication, repair, DNA structures, and context-dependent mutational biases. It is also observed that mitochondrial genome signature differences between species parallel the corresponding nuclear genome signature differences despite large differences between corresponding mitochondrial and nuclear signatures. The genome signature differences also have implications for contrasts between rodents and other mammals, and between monocot and dicot plants, as well as providing evidence for similarities among fungi and the diversity of protists.

Reciprocal interactions between β1-integrin and epidermal growth factor receptor in three-dimensional basement membrane breast cultures: A different perspective in epithelial biology

Anchorage and growth factor independence are cardinal features of the transformed phenotype. Although it is logical that the two pathways must be coregulated in normal tissues to maintain homeostasis, this has not been demonstrated directly. We showed previously that down-modulation of β1-integrin signaling reverted the malignant behavior of a human breast tumor cell line (T4–2) derived from phenotypically normal cells (HMT-3522) and led to growth arrest in a three-dimensional (3D) basement membrane assay in which the cells formed tissue-like acini (14). Here, we show that there is a bidirectional cross-modulation of β1-integrin and epidermal growth factor receptor (EGFR) signaling via the mitogen-activated protein kinase (MAPK) pathway. The reciprocal modulation does not occur in monolayer (2D) cultures. Antibody-mediated inhibition of either of these receptors in the tumor cells, or inhibition of MAPK kinase, induced a concomitant down-regulation of both receptors, followed by growth-arrest and restoration of normal breast tissue morphogenesis. Cross-modulation and tissue morphogenesis were associated with attenuation of EGF-induced transient MAPK activation. To specifically test EGFR and β1-integrin interdependency, EGFR was overexpressed in nonmalignant cells, leading to disruption of morphogenesis and a compensatory up-regulation of β1-integrin expression, again only in 3D. Our results indicate that when breast cells are spatially organized as a result of contact with basement membrane, the signaling pathways become coupled and bidirectional. They further explain why breast cells fail to differentiate in monolayer cultures in which these events are mostly uncoupled. Moreover, in a subset of tumor cells in which these pathways are misregulated but functional, the cells could be “normalized” by manipulating either pathway.

Functional expression of the Wilson disease protein reveals mislocalization and impaired copper-dependent trafficking of the common H1069Q mutation

Wilson disease is an autosomal recessive disorder of hepatic copper metabolism caused by mutations in a gene encoding a copper-transporting P-type ATPase. To elucidate the function of the Wilson protein, wild-type and mutant Wilson cDNAs were expressed in a Menkes copper transporter-deficient mottled fibroblast cell line defective in copper export. Expression of the wild-type cDNA demonstrated trans-Golgi network localization and copper-dependent trafficking of the Wilson protein identical to previous observations for the endogenously expressed protein in hepatocytes. Furthermore, expression of the Wilson cDNA rescued the mottled phenotype as evidenced by a reduction in copper accumulation and restoration of cell viability. In contrast, expression of an H1069Q mutant Wilson cDNA did not rescue the mottled phenotype, and immunofluorescence studies showed that this mutant Wilson protein was localized in the endoplasmic reticulum. Consistent with these findings, pulse–chase analysis demonstrated a 5-fold decrease in the half-life of the H1069Q mutant as compared with the wild-type protein. Maintenance of these transfected cell lines at 28°C resulted in localization of the H1069Q protein in the trans-Golgi network, suggesting that a temperature-sensitive defect in protein folding followed by degradation constitutes the molecular basis of Wilson disease in patients harboring the H1069Q mutation. Taken together, these studies describe a tractable expression system for elucidating the function and localization of the copper-transporting ATPases in mammalian cells and provide compelling evidence that the Wilson protein can functionally substitute for the Menkes protein, supporting the concept that these proteins use common biochemical mechanisms to effect cellular copper homeostasis.

A single gene for lycopene cyclase, phytoene synthase, and regulation of carotene biosynthesis in Phycomyces

Previous complementation and mapping of mutations that change the usual yellow color of the Zygomycete Phycomyces blakesleeanus to white or red led to the definition of two structural genes for carotene biosynthesis. We have cloned one of these genes, carRA, by taking advantage of its close linkage to the other, carB, responsible for phytoene dehydrogenase. The sequences of the wild type and six mutants have been established, compared with sequences in other organisms, and correlated with the mutant phenotypes. The carRA and carB coding sequences are separated by 1,381 untranslated nucleotides and are divergently transcribed. Gene carRA contains separate domains for two enzymes, lycopene cyclase and phytoene synthase, and regulates the overall activity of the pathway and its response to physical and chemical stimuli from the environment. The lycopene cyclase domain of carRA derived from a duplication of a gene from a common ancestor of fungi and Brevibacterium linens; the phytoene synthase domain is similar to the phytoene and squalene synthases of many organisms; but the regulatory functions appear to be specific to Phycomyces.

Estimation of divergence times from multiprotein sequences for a few mammalian species and several distantly related organisms

When many protein sequences are available for estimating the time of divergence between two species, it is customary to estimate the time for each protein separately and then use the average for all proteins as the final estimate. However, it can be shown that this estimate generally has an upward bias, and that an unbiased estimate is obtained by using distances based on concatenated sequences. We have shown that two concatenation-based distances, i.e., average gamma distance weighted with sequence length (d2) and multiprotein gamma distance (d3), generally give more satisfactory results than other concatenation-based distances. Using these two distance measures for 104 protein sequences, we estimated the time of divergence between mice and rats to be approximately 33 million years ago. Similarly, the time of divergence between humans and rodents was estimated to be approximately 96 million years ago. We also investigated the dependency of time estimates on statistical methods and various assumptions made by using sequence data from eubacteria, protists, plants, fungi, and animals. Our best estimates of the times of divergence between eubacteria and eukaryotes, between protists and other eukaryotes, and between plants, fungi, and animals were 3, 1.7, and 1.3 billion years ago, respectively. However, estimates of ancient divergence times are subject to a substantial amount of error caused by uncertainty of the molecular clock, horizontal gene transfer, errors in sequence alignments, etc.

Purification of the Trehalase GMTRE1 from Soybean Nodules and Cloning of Its cDNA. GMTRE1 Is Expressed at a Low Level in Multiple Tissues1

Trehalose (α-d-glucopyranosyl-1,1-α-d-glucopyranoside), a disaccharide widespread among microbes and lower invertebrates, is generally believed to be nonexistent in higher plants. However, the recent discovery of Arabidopsis genes whose products are involved in trehalose synthesis has renewed interest in the possibility of a function of trehalose in higher plants. We previously showed that trehalase, the enzyme that degrades trehalose, is present in nodules of soybean (Glycine max [L.] Merr.), and we characterized the enzyme as an apoplastic glycoprotein. Here we describe the purification of this trehalase to homogeneity and the cloning of a full-length cDNA encoding this enzyme, named GMTRE1 (G. max trehalase 1). The amino acid sequence derived from the open reading frame of GMTRE1 shows strong homology to known trehalases from bacteria, fungi, and animals. GMTRE1 is a single-copy gene and is expressed at a low but constant level in many tissues.

The current biodiversity extinction event: Scenarios for mitigation and recovery

The current massive degradation of habitat and extinction of species is taking place on a catastrophically short timescale, and their effects will fundamentally reset the future evolution of the planet's biota. The fossil record suggests that recovery of global ecosystems has required millions or even tens of millions of years. Thus, intervention by humans, the very agents of the current environmental crisis, is required for any possibility of short-term recovery or maintenance of the biota. Many current recovery efforts have deficiencies, including insufficient information on the diversity and distribution of species, ecological processes, and magnitude and interaction of threats to biodiversity (pollution, overharvesting, climate change, disruption of biogeochemical cycles, introduced or invasive species, habitat loss and fragmentation through land use, disruption of community structure in habitats, and others). A much greater and more urgently applied investment to address these deficiencies is obviously warranted. Conservation and restoration in human-dominated ecosystems must strengthen connections between human activities, such as agricultural or harvesting practices, and relevant research generated in the biological, earth, and atmospheric sciences. Certain threats to biodiversity require intensive international cooperation and input from the scientific community to mitigate their harmful effects, including climate change and alteration of global biogeochemical cycles. In a world already transformed by human activity, the connection between humans and the ecosystems they depend on must frame any strategy for the recovery of the biota.

Two enzymes of diacylglyceryl-O-4′-(N,N,N,-trimethyl)homoserine biosynthesis are encoded by btaA and btaB in the purple bacterium Rhodobacter sphaeroides

Betaine lipids are ether-linked, nonphosphorous glycerolipids that resemble the more commonly known phosphatidylcholine in overall structure. Betaine lipids are abundant in many eukaryotes such as nonseed plants, algae, fungi, and amoeba. Some of these organisms are entirely devoid of phosphatidylcholine and, instead, contain a betaine lipid such as diacylglyceryl-O-4′-(N,N,N,-trimethyl)homoserine. Recently, this lipid also was discovered in the photosynthetic purple bacterium Rhodobacter sphaeroides where it seems to replace phosphatidylcholine under phosphate-limiting growth conditions. This discovery provided the opportunity to study the biosynthesis of betaine lipids in a bacterial model system. Mutants of R. sphaeroides deficient in the biosynthesis of the betaine lipid were isolated, and two genes essential for this process, btaA and btaB, were identified. It is proposed that btaA encodes an S-adenosylmethionine:diacylglycerol 3-amino-3-carboxypropyl transferase and btaB an S-adenosylmethionine-dependent N-methyltransferase. Both enzymatic activities can account for all reactions of betaine lipid head group biosynthesis. Because the equivalent reactions have been proposed for different eukaryotes, it seems likely that orthologs of btaA/btaB may be present in other betaine lipid-containing organisms.