Chemical composition of the chalcophanite rich surface of an encrusted rock ashore Lake Macquarie, Australia

Mineralogical interest in the nature of manganese oxide particulates in natural marine water (Suess, 1979), natural lake water (Klaveness, 1977), and simulated lake water (Giovanoli, 1980), prompted a search for such particulates in a large New South Wales coastal lake. The investigated waters did show the existence of manganese oxide replacement phenomena in fragmentary sedimentary rocks near the south margin of Lake Macquarie. The black crusts of manganese oxide discovered on rocks close to the waterline have revealed a three layers structure. Layer A (0-35 micron), adjacent to the rock, is composed essentially of kaolinite of weathering origin, together with low levels of manganese oxide without detectable Zn. Layer B (35-80 micron) follows as a manganese oxide layer containing admixed kaolinite and low amounts of Zn. Layer C (80-130 micron) is the closest to the surface and is made of Chalcophanite containing 10-15% of ZnO.

Analysis of radioactive manganiferous nodules from Tanokami, Japan

Characteristic black nodules have been retrieved in 1922 from the bed of the Kichijo River, that runs along the Tanakamiyama mountain in the Oni Province and ends into Lake Biwa in Japan. Their radiocativity has been studied along with that of crusts of similar nature found covering rock formations in the vicinity overlooking the stream. The high content in radium observed may be due to the high uranium content of the granite host rock typical of the Tanakamiyama formation.

Recent advances in catalysts for methanol synthesis via hydrogenation of CO and CO2

Since the start of last century, methanol synthesis has attracted great interests because of its importance in chemical industries and its potential as an environmentally friendly energy carrier. The catalyst for the methanol synthesis has been a key area of research in order to optimize the reaction process. In the literature, the nature of the active site and the effects of the promoter and support have been extensively investigated. In this updated review, the recent progresses in the catalyst innovation, optimization of the reaction conditions, reaction mechanism, and catalyst performance in methanol synthesis are comprehensively discussed. Key issues of catalyst improvement are highlighted, and areas of priority in R&D are identified in the conclusions.

Thermal stability of ion-implanted ZnO

Zinc oxide single crystals implanted at room temperature with high-dose (1.4x10(17) cm(-2)) 300 keV As+ ions are annealed at 1000-1200 degrees C. Damage recovery is studied by a combination of Rutherford backscattering/channeling spectrometry (RBS/C), cross-sectional transmission electron microscopy (XTEM), and atomic force microscopy. Results show that such a thermal treatment leads to the decomposition and evaporation of the heavily damaged layer instead of apparent defect recovery and recrystallization that could be inferred from RBS/C and XTEM data alone. This study shows that heavily damaged ZnO has relatively poor thermal stability compared to as-grown ZnO which is a significant result and has implications for understanding results on thermal annealing of ion-implanted ZnO. (c) 2005 Americian Institute of Physics.

Nanocrystalline zirconia as catalyst support in methanol synthosis

Nanocrystalline zirconia was synthesized and used as catalyst support for methanol synthesis. The nanocrystallite particles have new physical and textural properties which are critical in determining the catalytic performance. Nanocrystalline zirconia changes the electronic structure and affects the metal and support interactions on the catalyst. leading to facile reduction. intimate interaction between copper and zirconia, more corner defects and oxygen vacancies on the surface of the catalyst. All these changes are beneficial to the reaction of methanol synthesis from hydrogenation of CO2. As a result. higher conversion of CO2 and selectivity of methanol are achieved compared to the catalysts prepared by conventional co-precipitation method. (C) 2004 Elsevier B.V. All rights reserved.

Preparation of high purity ZnO nanobelts by thermal evaporation of ZnS

High purity one-dimensional ZnO nanobelts were synthesized by thermally evaporating commercial ZnS powders in a hydrogen-oxygen mixture gas at 1050 degrees C. It was found that these ZnO nanobelts had a single crystal hexagonal wurtzite structure growing along the [0001] direction. They had a rectangle-shaped cross-section with typical widths of 20 to 100 nanometers and lengths of up to hundreds of micrometers with lattice constants of a = 0.325 nm and c = 0.520 nm. The self-catalytic hydrogen-oxygen assisted growth of ZnO nanobelt is discussed. The photoluminescence (PL) characterization of the ZnO nanobelts shows strong near-band UV emission (about 383 nm) and one broad peak at 501 nm, which indicates that the ZnO nanobelts have good potential application in optoelectronic devices.

An evaluation of thermal plasmas in pyrometallurgy

The development of reliable, high powered plasma generators has resulted in many plasma processes being proposed as alternatives to existing pyrometallurgical technologies. This work evaluates the advantages and disadvantages of plasma systems by reviewing plasma generators, their integration with reactors and the process economics. Many plasma systems were shown to be technically and economically superior to existing technologies, but some of the plasma system advantages quoted in the literature were found to be impractical because of other system constraints. Process applications were limited by the power inputs available from plasma generators compared to AC electric furnaces. A series of trials were conducted where chromite and steelplant baghouse dusts were smelted in the Tetronics' 2.0 MW transferred arc/open bath reactor to confirm the operating characteristics of the plasma system and its economics. Chromite smelting was technical superior to submerged arc furnace technology, but the economics were unfavourable because of the limited power available from the water-cooled plasma torch and the high electrical energy consumption. A DC graphite electrode plasma furnace using preheated and prereduced chromite concentrates will compete economically with the submerged arc furnace. Ni, Cr and Mo were economically recovered from high alloy content steelplant dusts for recycling. Five Electric Arc Furnace dusts were smelted to produce a non-toxic residue and recover the contained zinc to an enriched zinc oxide product for recycling. It should be possible to condense the zinc vapour directly in a zinc splash condenser to increase the value of the product. Because of the limited power available from plasma generators, plasma processes will be most suitable for treating high and medium value materials such as Au, Pt, Mo, Ni, Ti, V, Cr etc at small production rates, heating metals in tundishes and ladles and remelting superalloy scrap. The treatment of environmentally hazardous waste materials is a particularly interesting application because of the additional financial incentives. Non-transferred arc plasma generators will be used for air and gas preheating in blast furnaces to reduce metallurgical coke consumptions.

Synthesis and characterisation of interfacial layers in organic solar cells

The quest for renewable energy sources has led to growing attention in the research of organic photovoltaics (OPVs), as a promising alternative to fossil fuels, since these devices have low manufacturing costs and attractive end-user qualities, such as ease of installation and maintenance. Wide application of OPVs is majorly limited by the devices lifetime. With the development of new encapsulation materials, some degradation factors, such as water and oxygen ingress, can almost be excluded, whereas the thermal degradation of the devices remains a major issue. Two aspects have to be addressed to solve the problem of thermal instability: bulk effects in the photoactive layer and interfacial effects at the photoactive layer/charge-transporting layers. In this work, the interface between photoactive layer and electron-transporting zinc oxide (ZnO) in devices with inverted architecture was engineered by introducing polymeric interlayers, based on zinc-binding ligands, such as 3,4-dihydroxybenzene and 8-hydroxyquinoline. Also, a cross-linkable layer of poly(3,4-dimethoxystyrene) and its fullerene derivative were studied. At first, controlled reversible addition-fragmentation chain transfer (RAFT) polymerisation was employed to achieve well-defined polymers in a range of molar masses, all bearing a chain-end functionality for further modifications. Resulting polymers have been fully characterised, including their thermal and optical properties, and introduced as interlayers to study their effect on the initial device performance and thermal stability. Poly(3,4-dihydroxystyrene) and its fullerene derivative were found unsuitable for application in devices as they increased the work function of ZnO and created a barrier for electron extraction. On the other hand, their parental polymer, poly(3,4-dimethoxystyrene), and its fullerene derivative, upon cross-linking, resulted in enhanced efficiency and stability of devices, if compared to control. Polymers based on 8-hydroxyquinoline ligand had a negative effect on the initial stability of the devices, but increased the lifetime of the cells under accelerated thermal stress. Comprehensive studies of the key mechanisms, determining efficiency, such as charge generation and extraction, were performed by using time-resolved electrical and spectroscopic techniques, in order to understand in detail the effect of the interlayers on the device performance. Obtained results allow deeper insight into mechanisms of degradation that limit the lifetime of devices and prompt the design of better materials for the interface stabilisation.

Hierarchical ZnO “rod like” architecture synthesized via reverse micellar route for improved photocatalytic activity

Hierarchical ZnO “rod like” architecture was successfully synthesized via reverse micellar route and characterized by various techniques. The FESEM studies show controlled decomposition of zinc oxalate into ZnO “rod like” architecture at 500 °C with slow heat rate at 1°/min. Interestingly, improved photocatalytic activity was observed for the degradation of Rhodamine B, due to the self assembly of hexagonal nanoparticles of zinc oxide forming hierarchical ZnO “rod like” architecture which can greatly enhance the light utilization rate due to its special architecture and enlarge the specific surface area, providing more reaction sites and promoting mass transfer. More importantly, the reusability studies of this architecture were most economical.

Clean hydrogen production and carbon dioxide capture methods

Fossil fuels constitute a significant fraction of the world's energy demand. The burning of fossil fuels emits huge amounts of carbon dioxide into the atmosphere. Therefore, the limited availability of fossil fuel resources and the environmental impact of their use require a change to alternative energy sources or carriers (such as hydrogen) in the foreseeable future. The development of methods to mitigate carbon dioxide emission into the atmosphere is equally important. Hence, extensive research has been carried out on the development of cost-effective technologies for carbon dioxide capture and techniques to establish hydrogen economy. Hydrogen is a clean energy fuel with a very high specific energy content of about 120MJ/kg and an energy density of 10Wh/kg. However, its potential is limited by the lack of environment-friendly production methods and a suitable storage medium. Conventional hydrogen production methods such as Steam-methane-reformation and Coal-gasification were modified by the inclusion of NaOH. The modified methods are thermodynamically more favorable and can be regarded as near-zero emission production routes. Further, suitable catalysts were employed to accelerate the proposed NaOH-assisted reactions and a relation between reaction yield and catalyst size has been established. A 1:1:1 molar mixture of LiAlH 4, NaNH2 and MgH2 were investigated as a potential hydrogen storage medium. The hydrogen desorption mechanism was explored using in-situ XRD and Raman Spectroscopy. Mesoporous metal oxides were assessed for CO2 capture at both power and non-power sectors. A 96.96% of mesoporous MgO (325 mesh size, surface area = 95.08 ± 1.5 m2/g) was converted to MgCO 3 at 350°C and 10 bars CO2. But the absorption capacity of 1h ball milled zinc oxide was low, 0.198 gCO2 /gZnO at 75°C and 10 bars CO2. Interestingly, 57% mass conversion of Fe and Fe 3O4 mixture to FeCO3 was observed at 200°C and 10 bars CO2. MgO, ZnO and Fe3O4 could be completely regenerated at 550°C, 250°C and 350°C respectively. Furthermore, the possible retrofit of MgO and a mixture of Fe and Fe3O 4 to a 300 MWe coal-fired power plant and iron making industry were also evaluated.

(Table 1) Chemical composition of a sample contaiting native aluminium, Core DM9-647, Northeast Pacific

Composition, structure and occurrence of native aluminium in bottom sediments of the Northeast Pacific at Station DM9-647 are reported.

Mechanismus der CR-Vernetzung mit Ethylenthio-harnstoff und Zinkoxid

Es wurde eine Untersuchung zum Mechanismus der Vernetzung von Polychloropren durch Ethylenthioharnstoff in Kombination mit Zinkoxid durchgeführt. Dies wurde mit einer Überprüfung der Vernetzungsmechanismen von Polychloroprenkautschuk mit Ethylenthioharnstoff und Zinkoxid getrennt bzw. gemeinsam erreicht. Dabei kamen spektroskopische und physikalische Charakterisierungsverfahren zum Einsatz, um die Vernetzungsmechanismen von  CR mit anderen Standardvulkanisationsbeschleunigern und Modellverbindungen – mit ETU-analogen Strukturen und Funktionalitäten – zu erforschen. Aus den Untersuchungen resultierte der Vorschlag zu einem neuen Mechanismus, nach dem ETU und ZnO Polychloropren synergistisch vernetzen. Zusätzlich wurden neue Hinweise gewonnen, die gleichzeitig bestehende Mechanismen, die schon zur Vernetzung von Polychloropren veröffentlicht wurden, untermauern. An investigation into the mechanism by which ethylene thiourea crosslinks polychloroprene in combination with zinc oxide was undertaken. This was achieved through an examination of the mechanisms of crosslinking polychloroprene rubber with ETU and ZnO separately and in unison. Spectroscopic and physical characterisation techniques were employed to probe the crosslinking mechanisms of CR using other standard rubber accelerators and model compounds with analogous structures and functionalities to ETU. These investigations have resulted in the proposal of a new mechanism by which ETU and ZnO can synergistically crosslink polychloroprene, in addition to providing new evidence to support concomitant mechanisms already published for crosslinking polychloroprene.

Excitonic behaviour in polymeric semiconductors : the effect of morphology and composition in heterostructures

La compréhension des interrelations entre la microstructure et les processus électroniques dans les polymères semi-conducteurs est d’une importance primordiale pour leur utilisation dans des hétérostructures volumiques. Dans cette thèse de doctorat, deux systémes diffèrents sont étudiés ; chacun de ces systèmes représente une approche diffèrente pour optimiser les matériaux en termes de leur microstructure et de leur capacité à se mettre en ordre au niveau moléculaire. Dans le premier système, j’ai effectué une analyse complète des principes de fonctionnement d’une cellule photovoltaïque hybride à base des nanocristaux d’oxyde de zinc (ZnO) et du poly (3-hexylthiophène) (P3HT) par absorption photoinduite en régime quasi-stationnaire (PIA) et la spectroscopie PIA en pompage modulé dépendant de la fréquence. L’interface entre le donneur (le polymère P3HT) et l’accepteur (les nanoparticules de ZnO), où la génération de charges se produit, joue un rôle important dans la performance des cellules photovoltaïques hybrides. Pour améliorer le mécanisme de génération de charges du P3H: ZnO, il est indispensable de modifier l’interface entre ses constituants. Nous avons démontré que la modification d’interface moléculaire avec cis-bis (4, 40 - dicarboxy-2, 20bipyridine) ruthénium (II) (N3-dye) et a-Sexithiophen-2 yl-phosphonique (6TP) a améliorée le photocourant et la performance dans les cellules P3HT: ZnO. Le 6TP et le N3 s’attachent à l’interface du ZnO, en augmentant ainsi l’aire effective de la surface donneur :accepteur, ce qui contribue à une séparation de charge accrue. De plus, le 6TP et le N3 réduisent la densité de pièges dans le ZnO, ce qui réduit le taux de recombinaison des paires de charges. Dans la deuxième partie, jai introduit une matrice hôte polymérique de polystyréne à masse molaire ulra-élevée, qui se comporte comme un solide pour piéger et protéger une solution de poly [2-méthoxy, 5- (2´-éthyl-hexoxy) -1,4-phénylènevinylène- PPV] (MEHPPV) pour utilisation dans des dispositifs optoèlectroniques quantiques. Des travaux antérieurs ont montré que MEH-PPV en solution subit une transition de conformation, d’une conformation enroulé à haute température (phase bleue) à une conformation de chaîne étendue à basse température (phase rouge). La conformation de la chaîne étendue de la solution MEH-PPV favorise les caractéristiques nécessaires à l’amélioration des dispositifs optoélectroniques quantiques, mais la solution ne peut pas être incorporées dans le dispositif. J’ai démontré que la caractéristique de la phase rouge du MEH-PPV en solution se maintient dans une matrice hôte polymérique de polystyrène transformé de masse molaire très élevée, qui se comporte comme un solide (gel de MEH-PPV/UHMW PS), par le biais de la spectroscopie de photoluminescence (PL) dépendant de la température (de 290K à 80 K). La phase rouge du gel MEH-PPV/UHMW PS se manifeste par des largeurs de raie étroites et une intensité augmentée de la transition 0-0 de la progression vibronique dans le spectre de PL ainsi qu’un petit décalage de Stokes entre la PL et le spectre d’absorption à basse température. Ces approches démontrent que la manipulation de la microstructure et des propriétés électroniques des polymères semi-conducteurs ont un impact direct sur la performance de dispositifs pour leurs développements technologiques continus.