Individual and combined additions of calcium and antimony on microstructure and mechanical properties of squeeze-cast AZ91D magnesium alloy

The effects of combined additions of Ca and Sb on the microstructure and tensile properties of AZ91D alloy fabricated by squeeze-casting have been investigated. For comparison, the same has also been studied with and without individual additions of Ca and Sb. The results indicate that both individual and combined additions refine the grain size and beta-Mg17Al12 phase, which is more pronounced with combined additions. Besides alpha-Mg and beta-Mg17Al12 phases, a new reticular Al2Ca and rod-shaped Mg3Sb2 phases are formed following individual additions of Ca and Sb in the AZ91D alloy. With combined additions, an additional Ca2Sb phase is formed suppressing Mg3Sb2 phase. Additions of both Ca and Sb increase yield strength (YS) at both ambient and elevated temperatures up to 200 degrees C. However, both ductility and ultimate tensile strength (UTS) decrease first up to 150 degrees C and then increase at 200 degrees C. The increase in YS is attributed to the refinement of grain size, whereas, ductility and UTS are deteriorated by the presence of brittle Al2Ca, Mg3Sb2 and Ca2Sb phases. The best tensile properties are obtained in the AZXY9110 alloy owing to the presence of lesser amount of brittle Al2Ca and Ca2Sb phases resulted from the optimum content of 1.0Ca and 0.3Sb (wt%). The fracture surface of the tensile specimen tested at ambient temperature reveals cleavage failure that changes to quasi-cleavage at 200 degrees C. The squeeze-cast alloys exhibited better tensile properties as compared to that of the gravity-cast alloys nullifying the detrimental effects of Ca and/or Sb additions. (C) 2014 Elsevier B.V. All rights reserved.

Eu3+-activated SrMoO4 phosphors for white LEDs applications: Synthesis and structural characterization

We report the synthesis of Eu3+-activated SrMoO4 phosphors by the facile nitrate-citrate gel combustion method. Powder XRD and Rietveld refinement data confirmed that these phosphors have a monophasic scheelite-type tetragonal structure with space group I4(1)/a (No. 88). FESEM micrographs indicate the agglomerated spherical particles. FTIR spectra showed four stretching and bending vibrational modes (2A(u) and 2E(u)). UV-Visible absorption spectroscopy illustrated that the optical band gap energy (E-g) values increase with increase in Eu3+ concentration. The host SrMoO4 phosphor exhibited an intense blue emission under UV excitation (368 nm). The Eu3+-activated SrMoO4 phosphors revealed characteristic luminescence due to Eu3+ ion corresponding to D-5(1) -> F-7(J) (J = 1,2) and D-5(0) -> F-7(J) (J = 1,2,3,4) transitions upon 465 nm excitation. The electric dipole transition located at 615 nm (D-5(0) -> F-7(2)) was stronger than the magnetic dipole transition located at 592 nm (D-5(0) -> F-7(1)). Intensity parameters (Omega(2), Omega(4)) and radiative properties such as transition probabilities (A(T)), radiative lifetime (tau(rad)) and branching ratio (beta) of Eu3+-activated SrMoO4 phosphors were calculated using the Judd-Ofelt theory. Based on the CIE chromaticity diagram, these phosphors can be promising materials for the development of blue and orange-red component in white LEDs. (C) 2015 Elsevier B.V. All rights reserved.

Outer Bounds on the Sum Rate of the K-User MIMO Gaussian Interference Channel

This paper derives outer bounds on the sum rate of the K-user MIMO Gaussian interference channel (GIC). Three outer bounds are derived, under different assumptions of cooperation and providing side information to receivers. The novelty in the derivation lies in the careful selection of side information, which results in the cancellation of the negative differential entropy terms containing signal components, leading to a tractable outer bound. The overall outer bound is obtained by taking the minimum of the three outer bounds. The derived bounds are simplified for the MIMO Gaussian symmetric IC to obtain outer bounds on the generalized degrees of freedom (GDOF). The relative performance of the bounds yields insight into the performance limits of multiuser MIMO GICs and the relative merits of different schemes for interference management. These insights are confirmed by establishing the optimality of the bounds in specific cases using an inner bound on the GDOF derived by the authors in a previous work. It is also shown that many of the existing results on the GDOF of the GIC can be obtained as special cases of the bounds, e. g., by setting K = 2 or the number of antennas at each user to 1.

Performance evaluation of a two-stage silica gel plus water adsorption based cooling-cum-desalination system

The first objective of this paper is to show that a single-stage adsorption based cooling-cum-desalination system cannot be used if air cooled heat rejection is used under tropical conditions. This objective is achieved by operating a silica gel + water adsorption chiller first in a single-stage mode and then in a 2-stage mode with 2 beds/stage in each case. The second objective is to improve upon the simulation results obtained earlier by way of empirically describing the thermal wave phenomena during switching of operation of beds between adsorption and desorption and vice versa. Performance indicators, namely, cooling capacity, coefficient of performance and desalinated water output are extracted for various evaporator pressures and half cycle times. The improved simulation model is found to interpret experimental results more closely than the earlier one. Reasons for decline in performance indicators between theoretical and actual scenarios are appraised. (C) 2015 Elsevier Ltd and IIR. All rights reserved.

Low temperature solution processed high-kappa ZrO2 gate dielectrics for nanoelectonics

The high-kappa gate dielectrics, specifically amorphous films offer salient features such as exceptional mechanical flexibility, smooth surfaces and better uniformity associated with low leakage current density. In this work, similar to 35 nm thick amorphous ZrO2 films were deposited on silicon substrate at low temperature (300 degrees C, 1 h) from facile spin-coating method and characterized by various analytical techniques. The X-ray diffraction and X-ray photoelectron spectroscopy reveal the formation of amorphous phase ZrO2, while ellipsometry analysis together with the Atomic Force Microscope suggest the formation of dense film with surface roughness of 1.5 angstrom, respectively. The fabricated films were integrated in metal-oxide-semiconductor (MOS) structures to check the electrical capabilities. The oxide capacitance (C-ox), flat band capacitance (C-FB), flat band voltage (V-FB), dielectric constant (kappa) and oxide trapped charges (Q(ot)) extracted from high frequency (1 MHz) C-V curve are 186 pF, 104 pF, 0.37V, 15 and 2 x 10(-11) C, respectively. The small flat band voltage 0.37V, narrow hysteresis and very little frequency dispersion between 10 kHz-1 MHz suggest an excellent a-ZrO2/Si interface with very less trapped charges in the oxide. The films exhibit a low leakage current density 4.7 x 10(-9)A/cm(2) at 1V. In addition, the charge transport mechanism across the MOSC is analyzed and found to have a strong bias dependence. The space charge limited conduction mechanism is dominant in the high electric field region (1.3-5 V) due to the presence of traps, while the trap-supported tunneling is prevailed in the intermediate region (0.35-1.3 V). Low temperature solution processed ZrO2 thin films obtained are of high quality and find their importance as a potential dielectric layer on Si and polymer based flexible electronics. (C) 2016 Published by Elsevier B.V.

海底管线强度评估中的两个问题

海底管线是海上油气田生产设施的重要组成部分,它一旦发生破坏会在各方面引起重大损失.挖沟和提吊引起应力超标是海底管线两种重要的破坏形式.挖沟和提吊问题的难点是:1)二者都是动边界问题,悬空长度本身就是未知量;2)挖沟问题中应考虑台阶升高处土壤支持的弹性影响(这比刚性处理更准确,但这会使边界条件更复杂);3)提吊是一个几何非线性问题,求解难度较大.本文给出挖沟和提吊作业状态下,海底管线的强度分析方法.在挖沟分析中,采用线性梁理论,将台阶升高处的土壤支持处理为线性弹簧.在提吊问题中,将管线模型化为大位移梁,采用打靶法,将边值问题转变为初值问题求解.文中还给出有关的典型数值计算结果.

Evaluación de los anabólicos de crecimiento implix, ganamax, ralgro en novillos (finalización) en el trópico seco de Nicaragua

Con el propósito de evaluar el efecto de tres promotores de crecimiento Implix, Ralqro, Ganamax y un qrupo Testiqo (4 tratamientos), sobre variables de rendimiento en novillos de repasto Criollos x Brahaman con niveles de encaste desconocido, en el trópico seco de Nicaragua (Nandaime) 20 novillos fueron distribuidos al azar, 5 novillos por tratamiento. El estudio tuvo una duración de 3 meses, tiempo en el cual los animales fueron Implantados con los anabólicos antes mencionados. Las variables estudiadas fueron ganancia media diaria (GMD), peso de la canal (PCC), peso a los 90 días (P90d). Los datos obtenidos para determinar estas variables fueron peso inicial, peso a los 15 días, peso final. Los datos obtenidos para determinar estas variables se sometieron a un análisis de varianza y luego a una separación de medios a través de la prueba de DUNCAN. Los tratamientos no tuvieron efecto (P>0.05) sobre la características física de la canal; sin embargo se obtuvo mayor porcentaje de carne maqra y menos grasa en los animales implantados. Los resultados de las variables en estudio presentaron los siguientes valores: Ganamax (T1)tuvo una GMD de 380 grs, peso a los 90 días 392 kq y rendimiento en canal caliente de 194 kq, sequido de Implix (T2l con GMD 360 grs, peso 90 días de 380 kq y rendimiento en canal caliente 189 kg, el tratamiento Ralqro (T3) tuvo un peso a los 90 días de 375 kq obteniendo un peso final igual que el tratamiento Testigo, GMD 260 grs para Ralgro y 300 grs para el tratamiento Testigo, un rendimiento en canal caliente 186 kq para e1 tratamiento Ralqro Y 185 kq para el tratamiento Testigo.

Efecto de diferentes densidades de siembra y niveles de fertilizacion nitrogenada sobre el rendimiento de Moringa oleifera, Managua, Nicaragua

El presente trabajo tuvo como objetivo evaluar el efecto de dos densidades de siembra y cuatro niveles nitrogenados sobre la producción de Moringa oleifera. El ensayo se llevo a cabo en la hacienda “Las Mercedes”, localizada geográficamente a 86° 16 ́ 50 ̈ longitud oeste 12° 9 ́ 2.66 ̈ longitud norte, Municipio de Managua, de junio 2007 a Octubre 2008. El diseño experimental usado fue un factorial con dos dens idades de siembra (100 000 plantas/ha y 166 666 plantas/ha) como factor principal y por 4 niveles de fertilización; (0 kg N/ha/año, 446 kg N/ha/año, 906.2 kg N/ha/año, 1334 kg N/ha/año); como factor secundario, en un arreglo de parcela dividida usando las Densidades como parcela principal y los niveles de fertilización como sub-parcela. Las variables de estudio fueron: Rendimiento de materia fresca total (RMFT),rendimiento de materia fresca fracción fina (RMFFF), rendimiento de materia fresca fracción gruesa (RMFFG), Rendimiento de materia seca total (RMST), Rendimiento de materia seca fracción fina (RMSFF), Rendimiento de materia seca fracción gruesa (RMFFG), Altura promedio de plantas, mortalidad de plantas y Tasa de Crecimiento (TC). Se realizó análisis de varianza (ANDEVA) y comparaciones con la Prueba de Tukey utilizando MINITAB, versión 13.0. los resultados en el ANDEVA mostraron que las densidades de siembra no presentaron efecto significativo (P<0.05) sobre las variables evaluadas, no así la fertilización que si presentaron efecto significativo (P<0.05) para todas las variables evaluadas, el nivel de fertilización nitrogenada III presentó los mejores resultados para las variables RMFT(186.35 Ton/ha/año), RMFFF(138.52Ton/ha/año), RMFFG(47.82 Ton/ha/año), RMST(26.43 Ton/ha/año), RMSFF(19.23 Ton/ha/año) y RMSFG(7.23 Ton/ha/año), Altura de las plantas (1.39 m) y TC(73.42kgMS/ha/dia)

The influence of corrosion on the erosion of aluminium by aqueous silica slurries

The slurry erosion-corrosion behaviour of aluminium in aqueous silica slurries containing 0.5 M NaCl, acetic acid and 0.1 M Na2CO3 at open circuit has been investigated using a modified slurry erosion rig. The erosion rates of aluminium in the NaCl and acetic acid slurries were much higher than those in an aqueous slurry without electrolyte additives even though the pure corrosion component was very small. Eroded specimens were examined by scanning electron and optical microscopy. In pure aqueous slurry erosion, the basic mechanism leading to mass loss was the ductile fracture of flakes formed on the eroded surface. In corrosive slurries, however, the mass loss was enhanced by cracking of the flakes induced by stress and corrosion. © 1995.

Coatings and surface treatments for protection against low-velocity erosion-corrosion in fluidized beds

Surface coatings and treatments have been used to reduce material loss of components in bubbling fluidized bed combustors (FBCs). The performance of protective coatings in FBC boilers and laboratory simulations is reviewed. Important coating properties to minimize wastage appear to be high hardness, low oxidation rate, low porosity, high adhesion and sufficient thickness to maintain protection for a long period. Economic considerations and criteria for choosing a suitable coating or treatment are discussed for the different types of bubbling FBC. © 1995.

Erosion-corrosion of mild steel in a temperature gradient

Thinning of heat-exchanger tubes by erosion-corrosion has been a problem in fluidized bed combustors (FBCs), particularly at lower metal temperatures where thicker, mechanically protective oxide scales are unable to form. Many laboratory-scale tests have shown a decrease in material loss at higher temperatures, in a similar manner to FBC boilers, but also show a decrease in wastage at low temperatures (e.g. 200°C) which has not been detected in boilers. It has been suggested that this difference is due to laboratory tests being carried out isothermally whereas in a FBC boiler the fluidized bed is considerably hotter than the metal heat exchanger tubing. In this laboratory study the simulation was therefore improved by internally cooling one of the two low carbon steel specimens. These were rotated in a horizontal plane within a lightly fluidized bed with relative particle velocities of 1.3-2.5 m s-1. Tests were carried out over a range of bed temperatures (200-500°C) and cooled specimen surface temperatures (115-500°C), with a maximum temperature difference between the two of 320°C. Although specimens exposed isothermally still showed maximum wastage at intermediate temperatures (about 350°C), those which were cooled showed high levels of wastage at temperatures as low as 200°C in a similar manner to FBC boilers. Cooling may modify the isothermal erosion-corrosion curve, causing it to broaden and the maximum wastage rate to shift to lower temperatures. © 1995.