Sistema de medição de energia baseado no medidor de energia Teridian 71M6515H

Esta tese de mestrado descreve o desenvolvimento, implementação e teste de um sistema de medição de energia concebido para um ambiente doméstico, baseado no circuito integrado medidor de energia Teridian 71M6515H. O sistema desenvolvido envia periodicamente os valores monitorizados para uma base de dados, através de uma rede sem fios com base no protocolo IEEE 802.11 (Wi-Fi). Os dados podem ser acedidos remotamente em tempo real, através de uma página na internet, onde é possível consultar a quantidade de energia consumida acumulada. Na primeira fase deste trabalho realizou-se o enquadramento do tema no contexto atual, realizando-se o estudo de alguns sistemas domésticos de monitorização do consumo de energia elétrica existentes no mercado. Numa segunda fase foi realizado o estudo dos componentes a serem utilizados, o desenho da placa de circuito impresso e o desenvolvimento do firmware, para que todo o processamento e manipulação dos dados fossem realizados pela unidade de aquisição de dados. Em seguida procedeu-se à construção da unidade de aquisição e à programação para o registo dos valores numa base de dados. A última fase consistiu nos testes de funcionamento da unidade de aquisição em conjunto com a aplicação de registo de dados. Com a implementação do sistema desenvolvido o consumidor doméstico poderá ter conhecimento, em tempo real, do custo de funcionamento dos equipamentos que possui e assim tomar decisões para os utilizar de forma mais racional, o que se pode traduzir numa economia dos recursos energéticos.

Análise toxicológica in vitro e in vivo de uma fucana antitrombótica da alga marrom Spatoglossum schdöederi

Fucan is a term used to denominate a family of sulfated polysaccharides rich in L-fucose. They are extracted mainly from the extracellular matrix of brown algae and echinoderms. The brown alga Spatoglossum schröederi (Dictyotaceae) has three heterofucans named A, B and C. Our research group have been extracted non anticoagulant heterofucan from S. schröederi which possess antithrombotic activity in vivo. However, their toxicity in vitro and in vivo has not yet been determined. For the results in toxicity in vitro, we observed that the fucan A at 20, 500 and 1000 μg/plate showed no mutagenic activity in Kado test (Microsuspension), when the bacterial strains TA97a, TA98, TA100 and TA102, with and without S9 were used. The comet assay showed that fucan A (from 20 to 1000 μg/mL) did not cause any genotoxic effect on CHO cells. There was no damage to the DNA of these cells, as evidenced by the tail length and tail moment, which were similar to that found for the negative control. The fucan A from S. schröederi was administered at 20 μg/g of rat (dose which it showed high antithrombotic activity) during two months. After that, the animals were killed and examined. The data showed that fucan A did not cause any change in biochemistry and hematological parameters, as well as, in the morphology and size of the rat s organs analyzed. In conclusion, this study indicates that fucan is a compound with potential pharmacological that has no toxicity

Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Efeito da adição de carbonatos em formulação de massa para revestimento cerâmico utilizando matérias-primas do Piauí

Piauí state is a major producer of traditional red ceramic burning as bricks, tiles and ceramic tiles, with its main production center located in the city of Teresina. The state has large reserves of raw materials that can be used in the ceramic coating as clays, quartz, talc and carbonates. However, in the preparation of ceramic bodies using only a mixture of clays with different characteristics. The study aims to evaluate the effect of adding two types of carbonates in the ceramic semiporous mass coating produced in Piauí and then to verify the potential use of these carbonates as supplementary raw material product manufactured or the feasibility of obtaining a ceramic plate that meets the specifications for the porous coating. For this, were characterized the ceramic Piauí coating mass, a calcitic carbonate and a dolomitic, were made in the levels of 2, 4, 8, 16, and 32%. The masses were formed by pressing and burneds in two environments: a laboratory furnace (1080°C, 1120°C, 1140°C, and 1160°C) and an industrial furnace (1140°C). Then, following tests of linear shrinkage water absorption, apparent porosity, bulk density and flexural strength. Furthermore, the fired specimens were tested for their macrostructure and microstructure. The results showed the possibility of using the carbonate in ceramic mass flooring produced in Piauí, as added in small proportions improved dimensional stability and increased mechanical strength of ceramics pieces. It also proved itself possible to produce porous coating when added in higher levels

Análise gráfica de estruturas porosas sobre a ótica da estereologia

In this work we developed a computer simulation program for physics porous structures based on programming language C + + using a Geforce 9600 GT with the PhysX chip, originally developed for video games. With this tool, the ability of physical interaction between simulated objects is enlarged, allowing to simulate a porous structure, for example, reservoir rocks and structures with high density. The initial procedure for developing the simulation is the construction of porous cubic structure consisting of spheres with a single size and with varying sizes. In addition, structures can also be simulated with various volume fractions. The results presented are divided into two parts: first, the ball shall be deemed as solid grains, ie the matrix phase represents the porosity, the second, the spheres are considered as pores. In this case the matrix phase represents the solid phase. The simulations in both cases are the same, but the simulated structures are intrinsically different. To validate the results presented by the program, simulations were performed by varying the amount of grain, the grain size distribution and void fraction in the structure. All results showed statistically reliable and consistent with those presented in the literature. The mean values and distributions of stereological parameters measured, such as intercept linear section of perimeter area, sectional area and mean free path are in agreement with the results obtained in the literature for the structures simulated. The results may help the understanding of real structures.

Desenvolvimento e caracterização de compósito a partir da borra da piaçava para construção da parábola de um fogão solar a concentração

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Protótipo de um microgerador termoelétrico de estado sólido: cogeração a gás

The thermoelectric energy conversion can be performed directly on generators without moving parts, using the principle of SEEBECK effect, obtained in junctions of drivers' thermocouples and most recently in semiconductor junctions type p-n which have increased efficiency of conversion. When termogenerators are exposed to the temperature difference (thermal gradient) eletromotriz a force is generated inducing the appearance of an electric current in the circuit. Thus, it is possible to convert the heat of combustion of a gas through a burner in power, being a thermoelectric generator. The development of infrared burners, using porous ceramic plate, is possible to improve the efficiency of heating, and reduce harmful emissions such as CO, CO2, NOx, etc.. In recent years the meliorate of thermoelectric modules semiconductor (TEG's) has stimulated the development of devices generating and recovery of thermal irreversibility of thermal machines and processes, improving energy efficiency and exergy these systems, especially processes that enable the cogeneration of energy. This work is based on the construction and evaluation of a prototype in a pilot scale, for energy generation to specific applications. The unit uses a fuel gas (LPG) as a primary energy source. The prototype consists of a porous plate burner infrared, an adapter to the module generator, a set of semiconductor modules purchased from Hi-Z Inc. and a heat exchanger to be used as cold source. The prototype was mounted on a test bench, using a system of acquisition of temperature, a system of application of load and instrumentation to assess its functioning and performance. The prototype had an efficiency of chemical conversion of 0.31% for electrical and heat recovery for cogeneration of about 33.2%, resulting in an overall efficiency of 33.51%. The efficiency of energy exergy next shows that the use of primary energy to useful fuel was satisfactory, although the proposed mechanism has also has a low performance due to underuse of the area heated by the small number of modules, as well as a thermal gradient below the ideal informed by the manufacturer, and other factors. The test methodology adopted proved to be suitable for evaluating the prototype

Análise do desempenho de um queimador infravermelho funcionando com gás liquefeito de petróleo e glicerina

The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with greater control of emissions due to the passage of exhaust gases through a macro-porous ceramic bed. This paper presents an infrared burner commercial, which was adapted an experimental ejector, capable of promoting a mixture of liquefied petroleum gas (LPG) and glycerin. By varying the percentage of dual-fuel, it was evaluated the performance of the infrared burner by performing an energy balance and atmospheric emissions. It was introduced a temperature controller with thermocouple modulating two-stage (low heat / high heat), using solenoid valves for each fuel. The infrared burner has been tested and tests by varying the amount of glycerin inserted by a gravity feed system. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by a data acquisition system which recorded real-time measurements of the thermocouples attached. The burner had a stable combustion at levels of 15, 20 and 25% of adding glycerin in mass ratio of LPG gas, increasing the supply of heat to the plate. According to data obtained showed that there was an improvement in the efficiency of the 1st Law of infrared burner with increasing addition of glycerin. The emission levels of greenhouse gases produced by combustion (CO, NOx, SO2 and HC) met the environmental limits set by resolution No. 382/2006 of CONAMA

Análise de um queimador infravermelho funcionando com combustível híbrido : GLP/Bio-óleo

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Avaliação da atividade antimalárica de extratos obtidos de algas marinhas no litoral do Rio Grande do Norte

Malaria is a major parasitic disease worldwide, accounting for about 500 million cases and causing 2 million to 3 million deaths annually. Four species are responsible for transmitting this disease to humans: Plasmodium falciparum, Plasmodium vivax, Plasmodium malariae and Plasmodium ovale. The parasite resistance to antimalarial drugs and the usual limitations of the vector control implications are contributing to the spread of the disease. The most of significant advances in the search for new antimalarial drugs is based on natural components, the main ones being currently used antimalarial drugs derived from plants. Research on natural products of marine origin (particularly algae) show that some species possess antiplasmodial activity. Knowing that the coast of Rio Grande do Norte is home to several species of algae, the present study was to evaluate, for the first time, the antimalarial activity of ethanolic extracts of seaweed Spatoglossum schroederi, Gracilaria birdiae and Udotea flabellum against Plasmodium falciparum 3D7 strain tests and in vitro using the murine model (Plasmodium berghei) for evaluation in vivo. These species were ground, macerated with ethanol for 24 hours and the extracts concentrated in rotaevaporador (45 ° C ± 5 ° C). For in vitro tests, the extracts were diluted and tested at concentrations between 100 and 1.56 μg/ml (seven concentrations in triplicate), in order to obtain IC50 of each extract. The cytotoxicity tests with macrophages and BGM were performed using the MTT colorimetric assay. BGM macrophages and cells were distributed in 96 wells per plate (1x 105 to macrophages and 1x104 cells per well for BGM) and incubated for 24h at 37 ° C. The ethanol extracts were diluted and tested at concentrations of 100 to 1,56 μg/ml (seven concentrations in triplicate). After periods of 24 hours of incubation with the extracts, 100 μg of MTT was added to each well, and 3 hours elapsed, the supernatant was removed and added 200 μl of DMSO in each well. The absorbance of each well was obtained by reading on a spectrophotometer at 570 nm filter. To evaluate the acute toxicity in vivo, Swiss mice received a single dose (oral) 2000 mg/kg/animal of each extract tested. The parameters of acute toxicity were observed for 8 days. For in vivo tests, Swiss mice were inoculated with 1x105 erythrocytes infected with P. berghei. The treatment was given first to fourth day after infection with 0.2 ml of the extracts in doses of 1000 and 500 mg//g animal. The negative control group received 0.2 ml of 2% Tween-20, whereas the positive control group received sub-dose of chloroquine (5 mg/kg/animal). The assessment of antimalarial activity was done by suppressing suppressing the parasitemia at 5 and 7 days after infection. The growth inhibition of parasites was determined relative to negative control (% inhibition = parasitaemia in control - parasitemia in sample / parasitemia control x 100), the mortality of animals was monitored daily for 30 days The results showed that algae Spatoglossum schroederi and Udotea flabellum showed antimalarial activity in vitro, with reduced parasitemia of 70.54% and 54, respectively. The extracts of the three algae tested showed moderate to high cytotoxicity. Algae S. schroederi and U. flabellum were active against P. berghei only at doses of 500 mg / kg with reduction ranging from 54.58 to 52.65% for the fifth day and from 32.24 to 47.34% for the seventh day, respectively. No toxicity was observed in vivo at the dose tested, over the 8 days of observation. Although preliminary data, the bioactive components in those possible seaweed may be promising for the development of new anti-malarial drugs

Description of a new species of skate of the genus Malacoraja Stehmann, 1970: the first species from the southwestern Atlantic Ocean, with notes on generic monophyly and composition (Chondrichthyes: Rajidae)

O primeiro registro para o Atlântico Sul ocidental de uma espécie do gênero Malacoraja Stehmann, 1970 é feita com base na descrição de Malacoraja obscura, espécie nova, proveniente do talude continental do Sudeste brasileiro dos estados do Espírito Santo e Rio de Janeiro em profundidades de 808-1105 m. A espécie nova é conhecida através de cinco exemplares e é distinta de seus congêneres pela sua coloração dorsal composta por numerosas manchas esbranquiçadas e pequenas na região do disco e nadadeiras pélvicas, por apresentar uma fileira irregular de espinhos ao longo da superfície dorsal mediana da cauda a qual persiste em espécimes maiores (desde a base da cauda até dois-terços do seu comprimento numa fêmea de 680 mm de comprimento total, CT) e uma região pequena desprovida de dentículos na base ventral da cauda (estendendo somente até a margem distal da nadadeira pélvica). Outros caracteres diagnósticos em combinação incluem a ausência de espinhos escapulares em indivíduos maiores, número elevado de fileiras dentárias (64/62 fileiras num macho subadulto de 505 mm de CT e 76/74 numa fêmea de 680 mm de CT) e de vértebras (27-28 Vtr, 68-75 Vprd), coloração ventral do disco uniformemente castanha escura, duas fenestras pós-ventrais na cintura escapular, fenestra pós-ventral posterior grande, forame magno circular e dois forames para a carótida interna na placa basal ventral do neurocrânio. Machos adultos não são conhecidos, porém uma descrição anatômica de M. obscura, sp. nov., é fornecida. Comparações são realizadas com todo o material conhecido de M. kreffti, com a literatura sobre M. senta e com material abundante de M. spinacidermis da África do Sul; M. obscura, sp. nov., assemelha-se mais a M. spinacidermis do Atlântico Sul oriental em esqueleto dérmico, coloração e tamanho. Malacoraja é monofilético devido à sua espinulação e apêndices rostrais conspícuos e é aparentemente composta por dois grupos de espécies, um para M. obscura e M. spinacidermis e outro para M. kreffti e M. senta, porém a elucidação das relações filogenéticas entre as espécies necessita de mais informações anatômicas, principalmente das duas últimas espécies.

Avaliação das atividades antinociceptiva e anti-inflamatória de uma heterofucana da alga Dictyota menstrualis

Fucana é um termo que define uma família de hetero e homopolissacarídeos que contem L-fucose em sua estrutura. Neste trabalho uma hererofucan F 2,0v da alga Dictyota menstrualis foi avaliada como agente antinociceptivo e antiinflamatório. A fucana F 2,0v inibiu a migração de leucócitos em até 100% (20.0 mg/kg) para a cavidade peritoneal após estimulo químico, porém, não alterou a expressão das interleucinas IL-1β, IL-6 e de TNF-α. Com relação a sensação dolorosa a F 2,0v (20.0 mg/kg) possui atividade antinociceptiva periférica com potência semelhante à dipirona. Por outro lado não apresentou efeito no teste da placa quente. Análises de microscopia confocal e citometria de fluxo mostram que a F 2,0v se liga a superfície dos leucócitos. O conjunto de resultados apresentados pela fucana F 2,0v sugerem que o mecanismo de ação está relacionado com sua capacidade de inibir a migração de leucócitos para o local da injúria tecidual. Em resumo os dados mostram que F 2,0v apresenta grande potencial como composto antinociceptivo e antiinflamatório. Estudos futuros serão realizados para caracterizar melhor o mecanismo de ação da F 2,0v

Avaliação do sistema conservante em formulação com extrato hidroalcóolico de schinus terebinthifolius raddi nacardiaceae

Schinus terebinthifolius Raddi is used in the treatment of skin and mucosal injuries, infections of respiratory, digestive and genitourinary systems. Currently one of the biggest problems faced for the industry of phytopharmaceuticals with regard to the quality of raw materials is the microbial contamination. The aim this study was to evaluate the antimicrobial action of the hidroalcoholic extract of aroeira, beyond testing the effectiveness of the preservative system in hidrogel to the base of this extract. The extracts were prepared by maceration in the ratio of 1:10 of solvent plant/with alcohol 40%. The methods for microbial count were pour plate and test for specific microorganisms, analyzing in third copy each one of the samples. The antimicrobial activity of aroeira extracts was performed using an agar diffusion method, using strains of S. aureus, P. aeruginosa, E. coli, B. subtilis, C. albicans, C. tropicalis, C. krusei, C. guilliermondii, T. rubrum, M. gypseum, A. flavus and A. niger. The formula with aroeira was evaluated by the challenge test. This method consisted of artificial contamination the sample with separate inóculos of A. niger, C. albicans, E. coli e S. aureus aeruginosa and determinations of survivors for the method of counting for pour plate , during times 0, 24h, 48h, 7 days, 14 days, 21 days and 28 days. How much to the results, one verified that the extract of aroeira in the 13,5 concentration mg/mL presented antimicrobial activity for cepas of E. coli, B. subtilis, P. aeruginosa e S. aureus, producing inhibition zone, on average with 13 mm of diameter. However it did not present no fungi activity. The formula with aroeira containig both methylparaben and propylparaben showed a good efficacy in challenge test front to strains of A. niger, C. albicans, E. coli, S. aureus. The A criteria of European Pharmacopoeia, adopted in this work, was verified that this product revealed the good preservative efficacy for the challenge test, time interval of the 28 days. However, it is interesting to extend this study, in order to carry through the sped up stability and the test of shelf, to establish the validity of this formularization

Induction of somatic embryogenesis in soybean: physicochemical factors influencing the development of somatic embryos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sensibilidade de Metarhizium anisopliae à temperatura e umidade em três tipos de solos

Este trabalho teve como objetivo investigar o efeito da temperatura e do teor de umidade do solo na sobrevivência de Metarhizium anisopliae (Metsch.) Sorok. em três tipos de solos. Foram utilizados o Latossolo Vermelho textura argilosa, Latossolo Vermelho textura média e Argissolo Vermelho Amarelo textura arenosa média. As temperaturas empregadas foram 21,5; 26,8 e 31,5°C, e os teores de umidade foram 35, 65 e 100% de saturação. A sobrevivência do fungo foi avaliada após zero, 20, 40, 60, 80, 100 e 120 dias de incubação em cada temperatura estudada. Na análise do efeito do teor de umidade, a sobrevivência foi avaliada após zero, 14, 28, 42, 56, 70, 84, 98 e 112 dias de incubação à temperatura de 27,0±1,0°C. em ambos os ensaios, foi determinado o número de unidades formadores de colônias (UFC) em placa de Petri. Houve influência significativa da temperatura e do teor de umidade na sobrevivência do fungo. O maior crescimento e a maior sobrevivência ocorreram nas temperaturas de 21,5 e 26,8°C, enquanto que, no solo incubado a 31,5°C, o fungo cresceu pouco, e a população declinou rapidamente. No teor de 65% de umidade, houve rápido crescimento do fungo, mas no 112° dia foi observado um declínio da população nos três tipos de solos. Nos teores de 35 e 100% de umidade, o crescimento foi menor, mas obteve-se maior sobrevivência do fungo no solo.