Readout architectures for hybrid pixel detector readout chips

The original contribution of this thesis to knowledge are novel digital readout architectures for hybrid pixel readout chips. The thesis presents asynchronous bus-based architecture, a data-node based column architecture and a network-based pixel matrix architecture for data transportation. It is shown that the data-node architecture achieves readout efficiency 99% with half the output rate as a bus-based system. The network-based solution avoids “broken” columns due to some manufacturing errors, and it distributes internal data traffic more evenly across the pixel matrix than column-based architectures. An improvement of > 10% to the efficiency is achieved with uniform and non-uniform hit occupancies. Architectural design has been done using transaction level modeling (TLM) and sequential high-level design techniques for reducing the design and simulation time. It has been possible to simulate tens of column and full chip architectures using the high-level techniques. A decrease of > 10 in run-time is observed using these techniques compared to register transfer level (RTL) design technique. Reduction of 50% for lines-of-code (LoC) for the high-level models compared to the RTL description has been achieved. Two architectures are then demonstrated in two hybrid pixel readout chips. The first chip, Timepix3 has been designed for the Medipix3 collaboration. According to the measurements, it consumes < 1 W/cm^2. It also delivers up to 40 Mhits/s/cm^2 with 10-bit time-over-threshold (ToT) and 18-bit time-of-arrival (ToA) of 1.5625 ns. The chip uses a token-arbitrated, asynchronous two-phase handshake column bus for internal data transfer. It has also been successfully used in a multi-chip particle tracking telescope. The second chip, VeloPix, is a readout chip being designed for the upgrade of Vertex Locator (VELO) of the LHCb experiment at CERN. Based on the simulations, it consumes < 1.5 W/cm^2 while delivering up to 320 Mpackets/s/cm^2, each packet containing up to 8 pixels. VeloPix uses a node-based data fabric for achieving throughput of 13.3 Mpackets/s from the column to the EoC. By combining Monte Carlo physics data with high-level simulations, it has been demonstrated that the architecture meets requirements of the VELO (260 Mpackets/s/cm^2 with efficiency of 99%).

Identification of Albizia lebbeck seed coat chitin-binding vicilins (7S globulins) with high toxicity to the larvae of the bruchid Callosobruchus maculatus

Seed coat is a specialized maternal tissue that interfaces the embryo and the external environment during embryogenesis, dormancy and germination. In addition, it is the first defensive barrier against penetration by pathogens and herbivores. Here we show that Albizia lebbeck seed coat dramatically compromises the oviposition, eclosion and development of the bruchid Callosobruchus maculatus. Dietary supplementation of bruchid larvae with A. lebbeck seed coat flour causes severe weight loss and reduces survival. By means of protein purification, mass spectrometry and bioinformatic analyses, we show that chitin-binding vicilins are the main source of A. lebbeck tegumental toxicity to C. maculatus. At concentrations as low as 0.1%, A. lebbeck vicilins reduce larval mass from 8.1 ± 1.7 (mass of control larvae) to 1.8 ± 0.5 mg, which corresponds to a decrease of 78%. Seed coat toxicity constitutes an efficient defense mechanism, hindering insect predation and preventing embryo damage. We hypothesize that A. lebbeck vicilins are good candidates for the genetic transformation of crop legumes to enhance resistance to bruchid predation.

HYBRID ARTIFICIAL NEURAL NETWORK APPLIEDTO MODELING SCFE OF BASIL AND ROSEMARY OILS

This work presents the results of a Hybrid Neural Network (HNN) technique as applied to modeling SCFE curves obtained from two Brazilian vegetable matrices. A series Hybrid Neural Network was employed to estimate the parameters of the phenomenological model. A small set of SCFE data of each vegetable was used to generate an extended data set, sufficient to train the network. Afterwards, other sets of experimental data, not used in the network training, were used to validate the present approach. The series HNN correlates well the experimental data and it is shown that the predictions accomplished with this technique may be promising for SCFE purposes.

Antioxidant activity, cito- and phototoxicity of pomegranate (Punica granatum L.) seed pulp extract

In the present work, a hydroethanolic extract was prepared from the entire seeds of pomegranate [Punica granatum L. (Punicaceae)] with Cachaça, a distilled Brazilian alcoholic beverage, protected from light for an 80-hour period. The desorption curve of the seeds, presented an optimal time extraction of approximately 24 hours. The extract was divided into two samples: protected from light, (Extract 1), or not, (Extract 2). The extracts were characterized by UV-Visible absorption spectroscopy, quantification of total phenolics by the Folin-Ciocalteu method, and the antioxidant activity was determined by the DPPH quenching method. Extract 2 presented 9.8% less total polyphenols than Extract 1. The pomegranate seeds extract lost 79% of its antioxidant activity during light exposure. Extract 1 up to 3% (w/v) showed neither cyto nor phototoxicity in the Hela cells. In conclusion, Punica granatum L. seeds contain a significant total polyphenol and TEAC amount and they can be used in simple extractive process, by direct contact with Cachaça in up to 80 hours in the darkness, which gives it good coloration, taste, and smell. This extract showed neither cytotoxicity nor post-irradiation phototoxicity with solar simulator even though the extract proved photoinstable.

Macrocospic and physiochemical characterization of a sugarless and gluten-free cake enriched with fibers made from pumpkin seed (Cucurbita maxima, L.) flour and cornstarch

The Consumers' interest for products with caloric reduction has increased, and their development is a technological challenge. The consumption of cakes has grown in importance and the demand for dietary products has stimulated the use of sweeteners and the optimization of bakery products. The consumption of fibers is related to chronic diseases prevention. Pumpkin seeds (maximum Cucurbita, L.), rich in fibers, can be used as a source of fiber in food products. A gluten-free diet is not easy to follow since gluten free products are not always available. The objective of this work was to perform a physicochemical characterization of cakes prepared with flours blends (FB) based on Pumpkin Seed Flour (PSF). The cakes were elaborated with FB in the ratios of 30:70 (C30) and 40:60 (C40) of PSF and cornstarch (CS), respectively. The results showed gluten absence and near-neutral pH. The chemical analysis of C30 and B40 showed increase of ashes, lipids, proteins, and insoluble dietary fiber and a decrease in the content of carbohydrates and calories. The chemical composition of C40 presented the greatest content of lipids, proteins, and dietary fibers, the lowest content of calories, and the best physical parameters. Therefore, both products proved suitable for human consumption.

Antioxidant effect of mango seed extract and butylated hydroxytoluene in bologna-type mortadella during storage

The effects of mango seed extract (MSE) and butylated hydroxytoluene (BHT) on pH, lipid oxidation, and color of Bologna-type mortadella during refrigerated storage for 21 days were studied. Bologna-type mortadella samples were formulated to contain 0.1% MSE, 0.2% MSE, or 0.01% BHT. After 14 days of storage, the products containing MSE 0.1 or 0.2% had higher pH values than those containing BHT 0.01%. Lipid oxidation values increased with storage time but were not affected by the type of antioxidant. The highest values for color parameter L* were observed for mortadella containing BHT 0.01% after 7, 14, and 21 days of storage. Values for the color parameters a* and b* tended to decrease during mortadella storage. Products containing 0.1 or 0.2% MSE showed higher values for color parameter a* and lower values for color parameter b* compared to those containing 0.01% BHT. It can be concluded that MSE can be used in 0.1 or 0.2% levels in Bologna-type mortadella with similar or better antioxidant effects than those of BHT 0.01%.

Adzuki beans (Vigna angularis) seed quality under several drying conditions

This study analyzed the drying process and the seed quality of adzuki beans (Vigna angularis). Grains of adzuki beans, with moisture content of 1.14 (decimal dry basis) at harvest and dried until the moisture content of 0.11 (decimal dry basis.) were used. Drying was done in an experimental drier maintened at controlled temperatures of 30, 40, 50, 60, and 70 ºC and relative humidity of 52.0, 28.0, 19.1, 13.1, and 6.8%, respectively. Physiological and technological seed quality was evaluated using the germination test, Index of Germination Velocity (IGV), electrical conductivity, and water absorption, respectively. Under the conditions tested in the present study, it can be concluded that drying time for adzuki beans decreases with the higher air temperatures of 60 and 70 ºC, and it affected the physiological and technological seed quality. Thus, to avoid compromising adzuki seeds quality, it is recommended to promote its drying up to 50 ºC.

Antioxidant and fatty acid profile of gabiroba seed (Campomanesisa Xanthocarpa Berg)

This study aimed to evaluate the antioxidant potential and fatty acid profile of gabiroba (Campomanesia xanthocarpa Berg) seeds. In order to obtain the extract, the seeds were dried, crushed, and subjected to sequential extraction by maceration and percolation in a modified soxhlet extractor using solvent polarity gradient composed of hexane, chloroform, ethyl acetate, and alcohol, respectively. The extraction time was six hours. The ethanol extract showed the highest antioxidant potential, given by the EC50 value and the amount of total phenolic compounds. High amounts of unsaturated fatty acids were found in the oil studied, especially the oleic acid.

Development and chemical and sensory characterization of pumpkin seed flour-based cereal bars

Pumpkin (Cucurbita maxima), popularly known as squash, is a widely grown vegetable in Brazil. In this study, pumpkin seed flours (PSF) with different granulometries were used: PSF 1 (medium granulometry) and PSF 2 (coarse granulometry) in the preparation of cereal bars (CB) with different combinations with brown oats. Five formulations were prepared: CB-1 (control - 25% brown oats and 0% PSF); CB-2 (12.5% PSF 1 and 12.5% brown oats); CB-3 (25% PSF 1 and 0% brown oats); CB-4 (12.5% PSF 2 and 12.5% brown oats); and CB-5 (25% PSF 2 and 0% brown oats). The acceptance test results were analyzed in a conventional preference mapping which indicated that the bars CB-2 and CB-5 received mostly the maximum hedonistic score. With the objective of developing a cereal bar replacing oats with PSF, the bars CB-2 and CB-5 were compared to the conventional bar CB-1. The cereal bars CB-2 and CB-5 showed an increase in crude protein (87.5% and 62.5%) and in dietary fiber (77% and 44%), respectively. These results allowed the classification of CB-2 and CB-5 as fiber sources; they can, therefore, be classified as light products according to the Brazilian legislation.

Chemical characterization of the flour of peel and seed from two papaya cultivars

Papaya is among the currently most important tropical fruits grown in Brazil and in the world. The fruit is mainly consumed fresh although it offers many industrial products. The processing of this fruit, as well as its fresh consumption, results in large amounts of waste, such as peels and seeds. Papaya consumption is one of the causes of significant loss of food value; therefore, new aspects on the use of its waste as by-products, or in the production of food additives, or even the incorporation of its flour in food have aroused great interest because these are products of high nutritional value, and their use may be economically viable. The objective of this study was to produce and characterize peel and seed flours from two papaya cultivars (Havai and Calimosa) for their chemical constituents focusing on possible use in foods. The proximate and mineral composition, titratable acidity, soluble solids, pH, contents of vitamin C, and phenolic compounds were determined. According to the results obtained, the papaya peel and seed flours had high contents of protein and fiber and therefore can be used as alternative sources of nutrients and can also be added in foods avoiding waste and adding value to the fruit.

Annatto seed residue (Bixa orellana L.): nutritional quality

Considering that annatto seeds are rich in protein, the present work aimed to evaluate the biological quality of this nutrient in the meal residue originating from annatto seed processing. We determined the general composition, mineral levels, amino acid composition and chemical scores, antinutritional factors, and protein quality using biological assays. The following values were obtained: 11.50% protein, 6.74% moisture, 5.22% ash, 2.22% lipids, 42.19% total carbohydrates and 28.45% fiber. The residue proved to be a food rich in fiber and also a protein source. Antinutritional factors were not detected. The most abundant amino acids were lysine, phenylalanine + tyrosine, leucine and isoleucine. Valine was the most limiting amino acid (chemical score 0.22). The protein quality of the seed residue and the isolated protein showed no significant differences. The biological value was lower than that of the control protein but higher than that found in other vegetables. Among the biochemical analyses, only creatinine level was decreased in the two test groups compared to the control group. Enzyme tests did not indicate liver toxicity. The results showed favorable aspects for the use of annatto seed residue in the human diet, meriting further research.

Grape seed oil: a potential functional food?

Grape seed oil (GSO) is not often consumed in Brazil and little is known of its nutritional value. Around the world there are already studies that point to the high levels of minority bioactive compounds and their relation to health benefits. The main constituent of GSO is linoleic fatty acid, some works are controversial and there is no consensus in literature regarding their effect on the animal organism. Thus, this study aimed to present a review of GSO and show the potential health effects of its major components, not only linoleic acid, but also γ-tocotrienol and β-sitosterol, and finally, their influence on lipid-modulating, anti and pro oxidative parameters.

Effect of seed maturation stages on physical properties and antioxidant activity in flaxseed ( Linum usitatissimum L.)

Abstract The changes in flaxseed constituents at different stages of maturity are reported. The physical properties and antioxidant activity of flaxseed oil during flaxseed development have been evaluated. Continuous decrease in total polyphenol content during flaxseed development. All the results showed no significant differences between HPLC-MS and TLC for quantitative determination of phospholipids classes. The fatty acid compositions of individual phospholipids were also reported. The antioxidant activity of oilseed was assessed by means of 2, 2-diphenyl-1-picryl-hydrazyl (DPPH) radical scavenging assay. The test demonstrated that the antioxidant activity of the flaxseed oil was found to be harvesting time-dependant.

Chemical composition and nutritive value of hot pepper seed (Capsicum annuum) grown in Northeast Region of China

Chemical composition and nutritive value of hot pepper seeds (Capsicum annuum) grown in Northeast Region of China were investigated. The proximate analysis showed that moisture, ash, crude fat, crude protein and total dietary fiber contents were 4.48, 4.94, 23.65, 21.29 and 38.76 g/100 g, respectively. The main amino acids were glutamic acid and aspartic acid (above 2 g/100 g), followed by histidine, phenylalanine, lysine, arginine, cysteine, leucine, tryptophan, serine, glycine, methionine, threonine and tyrosine (0.8-2 g/100 g). The contents of proline, alanine, valine and isoleucine were less than 0.8 g/100 g. The fatty acid profile showed that linoleic acid, palmitic acid, oleic acid, stearic acid and linolenic acid (above 0.55 g/100 g) as the most abundant fatty acids followed lauric acid, arachidic acid, gondoic acid and behenic acid (0.03-0.15 g/100 g). Analyses of mineral content indicated that the most abundant mineral was potassium, followed by magnesium, calcium, iron, zinc, sodium and manganese. The nutritional composition of hot pepper seeds suggested that they could be regarded as good sources of food ingredients and as new sources of edible oils.

Characterization of constituents, quality and stability of pomegranate seed oil (Punica granatum L.)

Abstract This study aimed to characterize pomegranate seed oil and evaluate its quality and stability parameters against those of linseed oil. The profile of fatty acids and phytosterols and the content of tocopherols were analyzed by gas chromatography and high performance liquid chromatography, respectively. The quality of both oils was assessed as recommended by the American Oil Chemists' Society (AOCS) and stability was evaluated using 2,2-diphenyl-1-picrylhydrazyl (DPPH), β-carotene bleaching (coupled oxidation of β-carotene/linoleic acid) and Rancimat® assays. While α-linolenic acid (52%) was the most abundant fatty acid in linseed oil (LO), punicic acid (55%) was highest in pomegranate seed oil (PSO). Tocopherols and phytosterols (175 and 539 mg/100 g, respectively) were greater in PSO than in LO (51 and 328 mg/100 g, respectively). Both oils met quality standards. The β-carotene bleaching and the DPPH assays showed greater oxidative stability for PSO than for LO. The Rancimat® method, on the other hand, indicated low stability for both oils.