Simultaneous analysis of five antidepressant drugs using direct injection of biofluids in a capillary restricted-access media-liquid chromatography-tandem mass spectrometry system

Direct analysis, with minimal sample pretreatment, of antidepressant drugs, fluoxetine, imipramine, desipramine, amitriptyline, and nortriptyline in biofluids was developed with a total run time of 8 min. The setup consists of two HPLC pumps, injection valve, capillary RAM-ADS-C18 pre-column and a capillary analytical C 18 column connected by means of a six-port valve in backflush mode. Detection was performed with ESI-MS/MS and only 1 mu m of sample was injected. Validation was adequately carried out using FLU-d(5) as internal standard. Calibration curves were constructed under a linear range of 1-250 ng mL(-1) in plasma, being the limit of quantification (LOQ), determined as 1 ng mL(-1), for all the analytes. With the described approach it was possible to reach a quantified mass sensitivity of 0.3 pg for each analyte (equivalent to 1.1-1.3 fmol), translating to a lower sample consumption (in the order of 103 less sample than using conventional methods). (C) 2008 Elsevier B.V. All rights reserved.

Microwave-assisted digestion procedures for biological samples with diluted nitric acid: Identification of reaction products

Microwave-assisted sample preparation using diluted nitric acid solutions is an alternative procedure for digesting organic samples. The efficiency of this procedure depends on the chemical properties of the samples and in this work it was evaluated by the determination of crude protein amount. fat and original carbon. Soybeans grains, bovine blood. bovine muscle and bovine viscera were digested in a cavity-microwave oven using oxidant mixtures in different acid concentrations. The digestion efficiency was evaluated based on the determination of residual carbon content and element recoveries using inductively coupled plasma optical emission spectrometry (ICP OES). In order to determine the main residual organic compounds, the digests were characterized by nuclear magnetic resonance (1 H NMR). Subsequently, studies concerning separation of nitrobenzoic acid isomers were performed by ion pair reversed phase liquid chromatography using a C18 stationary phase, water:acetonitrile:methanol (75:20:5, v/v/v) +0.05% (v/v) TFA as mobile phase and ultraviolet detection at 254 nm. Sample preparation based on diluted acids proved to be feasible and a recommendable alternative for organic sample digestion, reducing both the reagent volumes and the variability of the residues as a result of the process of decomposition. It was shown that biological matt-ices containing amino acids, proteins and lipids in their composition produced nitrobenzoic acid isomers and other organic compounds after cleavage of chemical bonds. (C) 2009 Elsevier B.V. All rights reserved.

Caracterização do concentrado de ilmenita produzido na Mina do Guaju, Paraíba, visando identificar inclusões de monazita e outros contaminantes

O presente estudo tem como proposta, identificar o modo como o mineral monazita se encontra no concentrado final de ilmenita. Este concentrado é o produto resultante do beneficiamento do minério extraído de depósitos do tipo pláceres, conhecidos como depósitos de areias pretas. Estes depósitos são formados por dunas litorâneas pertencentes à jazida do Guaju, no município de Mataraca-PB. Todo o processo de lavra e beneficiamento deste minério ocorre na Mina do Guaju, a qual é operada pela empresa Millennium Inorganic Chemicals do Brasil S/A, pertencente a Lyondell Chemical Company. A ilmenita é um mineral composto por óxido de ferro e titânio, FeTiO3. Quase toda a ilmenita produzida na mina é transferida para o processo de fabricação de pigmento. A exigência para o uso na fabricação de pigmento é de que o concentrado final de ilmenita tenha um teor mínimo de 53% de TiO2 e um teor máximo de 0,1% de P2O5, entre outras substâncias. A monazita é o principal mineral fonte de óxido de tório, que é radioativo. No processo de fabricação de pigmento, a monazita é um contaminante indesejado. De acordo com a proposta de trabalho, foi feito um estudo de caracterização mineralógica de amostras do concentrado final de ilmenita fornecidas pela empresa. Inicialmente foram feitas análises em lupa, onde muitos grãos de leucoxeno foram identificados. O leucoxeno é uma alteração da ilmenita que permanece com as mesmas características magnéticas e eletrostáticas, tornando impossível, assim, a sua separação no processo de concentração. Também foi verificada a existência de grãos de monazita liberados em pequenas quantidades neste concentrado, indicando uma provável ineficiência no processo de separação. Numa segunda etapa foram realizadas análises dos grãos de ilmenita com o uso de um Microscópio Eletrônico de Varredura (MEV) acoplado a um Espectrômetro de Dispersão de Energia (EDS), para permitir a determinação de elementos químicos na amostra. Esta análise teve como objetivo verificar a existência de inclusões de monazita nos grãos de ilmenita. Porém, o que se observou foi a existência de algumas inclusões de quartzo e de alguns vazios deixados, provavelmente, por inclusões arrancadas durante o processo de preparação das amostras. Alguns destes vazios apresentaram formas semelhantes a de cristais de monazita, indicando a possibilidade da existência de inclusões deste mineral. Entretanto, a quantidade de grãos com possíveis inclusões de monazita é muito pequena, sendo insignificante como contaminante do concentrado final. Embora alguns vazios se assemelhem à forma da monazita, nenhum dos resultados do EDS identificou vestígios de sua presença. Ao final deste estudo ficou evidente que a principal fonte de contaminação do concentrado final de ilmenita corresponde à monazita, a qual se encontra liberada neste concentrado. Desta forma, há a necessidade de se melhorar o processo de separação dos minerais, de modo que a quantidade de monazita no concentrado final seja a menor possível, não prejudicando o rendimento da recuperação de ilmenita.

O pão e a festa: patrimônio imaterial e turismo em Juiz de Fora

Esta pesquisa tem por objetivo analisar os pedidos de registro do Pão Alemão e da Deutsches Fest como bens culturais de natureza imaterial de Juiz de Fora, sendo elementos representantes da cultura e da tradição dos imigrantes alemães que fazem parte da história da cidade. A Festa Alemã ou Deutsches Fest é, atualmente, um dos maiores eventos do calendário cultural e turístico de Juiz de Fora, cidade localizada na Zona da Mata do Estado de Minas Gerais. Realizada no bairro Borboleta, antiga Colônia Alemã, a festa foi criada em 1969, por descendentes dos alemães que imigraram para o município, em meados do século XIX. O Pão Alemão, encontrado nas festas e casas do bairro, além de ser o principal elo de preservação da memória construída por esses descendentes alemães, tornou-se importante elemento simbólico, enquanto modo de preparo da legítima culinária alemã. Pão e Festa fazem parte de uma tradição constituída, ao longo de anos, para afirmar a identidade do grupo, proporcionando-lhe ampliar sua participação nos âmbitos políticos e econômicos locais.

(-)-Hinokinin-loaded poly(d,l-lactide-co-glycolide) microparticles for Chagas disease

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Método de preparo das sementes de mamoneira (Ricinus communis L.) para o teste de tetrazólio

O teste de tetrazólio é um método rápido e eficaz para avaliar a viabilidade e o vigor de sementes. O presente trabalho teve por objetivo padronizar o método de preparo das sementes de mamoneira (Ricinus communis L.) para a avaliação do potencial fisiológico pelo teste de tetrazólio. Foram testados os seguintes métodos de preparo das sementes: corte longitudinal mediano através do tegumento, endosperma e embrião; corte longitudinal diagonal sem atingir o eixo embrionário; remoção do tegumento; remoção do tegumento com corte longitudinal mediano através do endosperma e embrião; e remoção do tegumento com corte longitudinal mediano, paralelo aos cotilédones, através do endosperma e embrião. Antes dos preparos, as sementes foram pré-condicionadas entre papel toalha umedecido por 18 horas a 30ºC, e após os preparos, as sementes foram imersas na solução de tetrazólio na concentração de 0,5% e mantidas em câmara escura a 35ºC para o desenvolvimento da coloração. Avaliou-se a uniformidade da coloração das sementes após cada preparo, por meio da comparação entre eles. Para a avaliação do potencial fisiológico das sementes de mamoneira pelo teste de tetrazólio o método indicado de preparo é a remoção do tegumento, com posterior corte longitudinal e mediano, no sentido do comprimento, através do endosperma e embrião.

Monitoramento em tempo real de processos fermentativos por espectroscopia no infravermelho próximo (NIRS)

A chemical process optimization and control is strongly correlated with the quantity of information can be obtained from the system. In biotechnological processes, where the transforming agent is a cell, many variables can interfere in the process, leading to changes in the microorganism metabolism and affecting the quantity and quality of final product. Therefore, the continuously monitoring of the variables that interfere in the bioprocess, is crucial to be able to act on certain variables of the system, keeping it under desirable operational conditions and control. In general, during a fermentation process, the analysis of important parameters such as substrate, product and cells concentration, is done off-line, requiring sampling, pretreatment and analytical procedures. Therefore, this steps require a significant run time and the use of high purity chemical reagents to be done. In order to implement a real time monitoring system for a benchtop bioreactor, these study was conducted in two steps: (i) The development of a software that presents a communication interface between bioreactor and computer based on data acquisition and process variables data recording, that are pH, temperature, dissolved oxygen, level, foam level, agitation frequency and the input setpoints of the operational parameters of the bioreactor control unit; (ii) The development of an analytical method using near-infrared spectroscopy (NIRS) in order to enable substrate, products and cells concentration monitoring during a fermentation process for ethanol production using the yeast Saccharomyces cerevisiae. Three fermentation runs were conducted (F1, F2 and F3) that were monitored by NIRS and subsequent sampling for analytical characterization. The data obtained were used for calibration and validation, where pre-treatments combined or not with smoothing filters were applied to spectrum data. The most satisfactory results were obtained when the calibration models were constructed from real samples of culture medium removed from the fermentation assays F1, F2 and F3, showing that the analytical method based on NIRS can be used as a fast and effective method to quantify cells, substrate and products concentration what enables the implementation of insitu real time monitoring of fermentation processes

Estudo dos óxidos A2B2O7 e ABO3 a base de terras raras, para aplicações térmicas e catalíticas a altas temperaturas

Rare earth elements have recently been involved in a range of advanced technologies like microelectronics, membranes for catalytic conversion and applications in gas sensors. In the family of rare earth elements like cerium can play a key role in such industrial applications. However, the high cost of these materials and the control and efficiencies associated processes required for its use in advanced technologies, are a permanent obstacle to its industrial development. In present study was proposed the creation of phases based on rare earth elements that can be used because of its thermal behavior, ionic conduction and catalytic properties. This way were studied two types of structure (ABO3 and A2B2O7), the basis of rare earths, observing their transport properties of ionic and electronic, as well as their catalytic applications in the treatment of methane. For the process of obtaining the first structure, a new synthesis method based on the use of EDTA citrate mixture was used to develop a precursor, which undergone heat treatment at 950 ° C resulted in the development of submicron phase BaCeO3 powders. The catalytic activity of perovskite begins at 450 ° C to achieve complete conversion at 675 ° C, where at this temperature, the catalytic efficiency of the phase is maximum. The evolution of conductivity with temperature for the perovskite phase revealed a series of electrical changes strongly correlated with structural transitions known in the literature. Finally, we can establish a real correlation between the high catalytic activity observed around the temperature of 650 ° C and increasing the oxygen ionic conductivity. For the second structure, showed clearly that it is possible, through chemical processes optimized to separate the rare earth elements and synthesize a pyrochlore phase TR2Ce2O7 particular formula. This "extracted phase" can be obtained directly at low cost, based on complex systems made of natural minerals and tailings, such as monazite. Moreover, this method is applied to matters of "no cost", which is the case of waste, making a preparation method of phases useful for high technology applications

Interaction mechanism of poly (o-ethoxyaniline) and collagen blends

Blend films of poly (o-ethoxyaniline) (POEA) and collagen were fabricated by casting under optimized conditions and characterized by Raman scattering and UV-vis absorption spectroscopies. The UV-vis spectra showed that the addition of collagen in the aqueous solution of POEA promotes a dedoping of the POEA. This effect was also observed for the blend films as supported by Raman scattering and a mechanism for the chemical interaction between POEA-collagen is proposed. The influences of different percentage of collagen as well as the pH of stock solutions during the fabrication process of the blend films were also investigated. It was found that the preparation method plays an important role in the flexibility and freestanding properties of the films. Complementary, the surface morphology was studied by atomic force microscopy and the conductivity by dc measurements. (C) 2003 Elsevier Ltd. All rights reserved.

Exploiting Distinct Molecular Architectures of Ultrathin Films Made with Iron Phthalocyanine for Sensing

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Diagnosis of Smith-Lemli-Opitz syndrome by ultraviolet spectrophotometry

Smith-Lemli-Opitz syndrome (SLOS) is an autosomal recessive disorder due to an inborn error of cholesterol metabolism, characterized by congenital malformations, dysmorphism of multiple organs, mental retardation and delayed neuropsychomotor development resulting from cholesterol biosynthesis deficiency. A defect in 3ß-hydroxysteroid-delta7-reductase (delta7-sterol-reductase), responsible for the conversion of 7-dehydrocholesterol (7-DHC) to cholesterol, causes an increase in 7-DHC and frequently reduces plasma cholesterol levels. The clinical diagnosis of SLOS cannot always be conclusive because of the remarkable variability of clinical expression of the disorder. Thus, confirmation by the measurement of plasma 7-DHC levels is needed. In the present study, we used a simple, fast, and selective method based on ultraviolet spectrophotometry to measure 7-DHC in order to diagnose SLOS. 7-DHC was extracted serially from 200 µl plasma with ethanol and n-hexane and the absorbance at 234 and 282 nm was determined. The method was applied to negative control plasma samples from 23 normal individuals and from 6 cases of suspected SLOS. The method was adequate and reliable and 2 SLOS cases were diagnosed.

Thermal characterization of solid lipid nanoparticles containing praziquantel

Solid lipid nanoparticles (SLNs), loaded and unloaded with praziquantel (PRZ-load SLN and PRZ-unload SLN) were prepared by two different procedures: (a) oil-in-water hot microemulsion method, obtaining at 70 degrees C an optically transparent blend composed of surfactant, co-surfactant, and water; and (b) oil-in-water microemulsion method, dissolving the lipid in an immiscible organic solvent, emulsified in water containing surfactants and co-surfactant, and then evaporated under reduced pressure at 50 degrees C. The mean diameter, polydispersity index (PdI), and zeta potential were 187 to 665 nm, 0.300 to 0.655, and -25 to -28 mV respectively, depending on the preparation method. The components, binary mixture, SLNs loaded and unloaded with PRZ, and physical mixture were evaluated by differential scanning calorimetry (DSC) and thermogravimetry (TG). The non-isothermal isoconversional Flynn-Wall-Ozawa method was used to determine the kinetic parameters associated with the thermal decomposition of the samples. The experimental data indicated a linear relationship between the apparent activation energy E and the pre-exponential factor A, also called the kinetic compensation effect (KCE), allowing us to determine the stability with respect to the preparation method. Loading with PRZ increased the thermal stability of the SLNs.

Study of interstitial oxygen mobility in RuSr2GdCu2O8 by internal friction

The discovery of the spatial uniform coexistence of superconductivity and ferromagnetism in ruthenocuprates, RuSr2GdCu2O8 (Ru-1212), has spurred an extraordinary development in the study of the competition between magnetism and superconductivity. However, several points of their preparation process and characterization that determine their superconductive behaviour are still obscure. The improvement of sample preparation conditions involves some thermal treatments in inert atmosphere. Anelastic spectroscopy measurements were made using an inverted torsion pendulum, operating with an oscillation frequency of 38 Hz, temperature in the 90 and 310 K range, heating rate of 1 K/min, and vacuum better than 10(-3) Pa. The results show anelastic relaxation peaks at 210 K related to the presence of interstitial oxygen atoms. The peaks decrease significantly with the oxygen loss caused by the heat treatments in vacuum, appearing again after the annealing of the sample in an oxygen atmosphere. These observed peaks are clearly related to the additional oxygen atoms, with activation energy 0.13 and 0.36 eV, and can be explained in terms by diffusional jumps of interstitial oxygen in the RuO2 planes. (C) 2009 Elsevier B.V. All rights reserved.

Geoquímica de sedimentos de fundo dos rios Trairí, Ararí e da Laguna Nísia Floresta (RN)

The metal concentrations (Al, Ba, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Zn ) and phosforus(P) had been determined analyzed through Plasma Inductively Coupled Plasme Mass Spectrometer for fine fraction, < 0,63 mm in 22 samples. The sample preparation for analysis had been make in the laboratories of geology of the UFRN. This samples procedures consists in register, dry, bolt and send to analysis in external laboratory (LAKEFIELD GEOSOL) in Belo Horizonte (MG, Brazil). The studied area involves the rivers Trairi, Ararí and Nísia Floresta lagoon, that empties in the sea, situated in the Rio Grande do Norte State. The study objects (Rivers Trairí, Ararí and Nísia Floresta lagoon) receive influences from urban dumpies, agrotoxics and fertilizer, shrimps tank, pastoral, with this, the concentrations of metals (Al, Ba, Cd, Cr, Cu, Fe, Mn, Ni, Pb, P, Zn) (except phosforus) in some points of the study area had been above of the value of reference what it leads to classify them as not polluted to moderately polluted, as the calculated Igeo. In front of discussed, can say about the environmental problems found in Trairi, Ararí and Nísia Floresta Lagoon are still in small scale, since when regard the studied área is over human activity effects

Análise química de produtos de incrustação em dutos de petróleo por espectometria de fluorescência de raios X

The quantitative chemical characterization of the inorganic fraction of scale products is very relevant in studying, monitoring and controlling corrosive processes of oil pipelines. The X-ray fluorescence spectrometry (XRF) is a very versatile analytical technique, which can be used in quantitative analysis in solid samples at low concentrations of the chemical element, in the order of few ppm. A methodology that involves sample preparation diluted in the proportion of 1:7 (one portion of the sample for seven of wax), pressed as pellets was used in the XRF calibration for chemical analysis of scale products from oil pipelines. The calibration involved the preparation of reference samples from mixtures of P.A. reagents, aiming to optimize the time consumed in the steps of sample preparation and analysis of Al, Ba, Ca, Fe, K, Mg, Mn, Na, P, S, Si, Sr and Ti, using the same pressed pellet for trace and major elements analysis