Structural health evaluation by optimization techinique and artificial neural network

This paper presents two different approaches to detect, locate, and characterize structural damage. Both techniques utilize electrical impedance in a first stage to locate the damaged area. In the second stage, to quantify the damage severity, one can use neural network, or optimization technique. The electrical impedance-based, which utilizes the electromechanical coupling property of piezoelectric materials, has shown engineering feasibility in a variety of practical field applications. Relying on high frequency structural excitations, this technique is very sensitive to minor structural changes in the near field of the piezoelectric sensors, and therefore, it is able to detect the damage in its early stage. Optimization approaches must be used for the case where a good condensed model is known, while neural network can be also used to estimate the nature of damage without prior knowledge of the model of the structure. The paper concludes with an experimental example in a welded cubic aluminum structure, in order to verify the performance of these two proposed methodologies.

Paracoccidioidomicose

The aspects related to the epidemiology, pathogenesis, clinical classification, clinical manifestations and treatment of Paracoccidioidomycosis, are presented. The disease is caused by Paracoccidioides brasiliensis and is the most frequent and the most important systemic mycosis in the South America, specifically in Brazil, Argentina, Colombia and Venezuela. Because of the high frequency of cutaneous-mucosal lesions presented by the patients, the potential severity of the disease and the socio-economic consequences to the patient, it is very important for a drematologist to be qualified to precisely diagnose the disease and render proper care.

On designing linearly-tunable ultra-low voltage CMOS gm-C filters

A linearly-tunable ULV transconductor featuring excellent stability of the processed signal common-mode voltage upon tuning, critical for very-low voltage applications, is presented. Its employment to the synthesis of CMOS gm-C high-frequency and voiceband filters is discussed. SPICE data describe the filter characteristics. For a 1.3 V-supply, their nominal passband frequencies are 1.0 MHz and 3.78 KHz, respectively, with tuning rates of 12.52 KHz/mV and 0.16 KHz/m V, input-referred noise spectral density of 1.3 μV/Hz1/2 and 5.0μV/Hz1/2 and standby consumption of 0.87 mW and 11.8 μW. Large-signal distortion given by THD = 1% corresponds to a differential output-swing of 360 mVpp and 480 mVpp, respectively. Common-mode voltage deviation is less than 4 mV over tuning interval.

Impedance-based structural health monitoring with artificial neural networks

This paper presents a non-model based technique to detect, locate, and characterize structural damage by combining the impedance-based structural health monitoring technique with an artificial neural network. The impedance-based structural health monitoring technique, which utilizes the electromechanical coupling property of piezoelectric materials, has shown engineering feasibility in a variety of practical field applications. Relying on high frequency structural excitations (typically >30 kHz), this technique is very sensitive to minor structural changes in the near field of the piezoelectric sensors. In order to quantitatively assess the state of structures, multiple sets of artificial neural networks, which utilize measured electrical impedance signals for input patterns, were developed. By employing high frequency ranges and by incorporating neural network features, this technique is able to detect the damage in its early stage and to estimate the nature of damage without prior knowledge of the model of structures. The paper concludes with experimental examples, investigations on a massive quarter scale model of a steel bridge section and a space truss structure, in order to verify the performance of this proposed methodology.

Multipath reduction from GPS double differences using wavelets: How far can we go?

Wavelets are being extensively used in Geodetic applications. In this paper, the Multi-Resolution Analysis (MRA) using wavelets is applied to pseudorange and carrier phase GPS double differences (DDs) in order to reduce multipath effects. The wavelets were already applied to GPS carrier phase DDs, but some questions remain: How good can be the results, and are all multipath effects reduced? The answers to these questions are discussed in this paper. Thus, the wavelet transform is used to decompose the DD signals, splitting them in lower resolution components. After the decomposition process, the wavelet shrinkage is performed by thresholding to eliminate the components relative to multipath effects. Then, the DD observation can be reconstructed. This new DD signal is used to perform the baseline processing. The daily multipath repeatability was verified. With the application of the proposed approach, the results showed that the reliability of the ambiguity resolution and accuracy of the results improved when compared with the standard procedure. Furthermore, the method showed to be very efficient computationally, because, it is not noticed, at practical level, difference in the time span between the processing with and without application of the proposed method. However, only the high frequency multipath was eliminated.

An AC voltage regulator with high-power-factor, and control using a FPGA device

This paper presents the analysis, design, simulation, and experimental results for a high frequency high Power-Factor (PF) AC (Alternate Current) voltage regulator, using a Sepic converter as power stage. The control technique employed to impose a sinusoidal input current waveform, with low Total Harmonic Distortion (THD), is the sinusoidal variable hysteresis control. The control technique was implemented in a FPGA (Field Programmable Gate Array) device, using a Hardware Description Language (VHDL). Through the use of the proposed control technique, the AC voltage regulator performs active power-factor correction, and low THD in the input current, for linear and non-linear loads, satisfying the requirements of the EEC61000-3-2 standards. Experimental results from an example prototype, designed for 300W of nominal output power, 50kHz (switching frequency), and 127Vrms of nominal input and output voltages, are presented in order to validate the proposed AC regulator. © 2005 IEEE.

High cholesterol intake modifies chylomicron metabolism in normolipidemic young men

Whether the consumption of egg yolk, which has a very high cholesterol content without excess saturated fats, has deleterious effects on lipid metabolism is controversial. Absorbed dietary cholesterol enters the bloodstream as chylomicrons, but the effects of regular consumption of large amounts of cholesterol on the metabolism of this lipoprotein have not been explored even though the accumulation of chylomicron remnants is associated with coronary artery disease (CAD). We investigated the effects of high dietary cholesterol on chylomicron metabolism in normolipidemic, healthy young men. The plasma kinetics of a chylomicron-like emulsion, doubly-labeled with 14C-cholesteryl ester ( 14C-CE) and 3H-triolein ( 3H-TG) were assessed in 25 men (17-22 y old, BMI 24.1 ± 3.4 kg/m 2). One group (n = 13) consumed 174 ± 41 mg cholesterol/d and no egg yolk. The other group (n = 12) consumed 3 whole eggs/d for a total cholesterol intake of 804 ± 40 mg/d. The nutritional composition of diets was the same for both groups, including total lipids and saturated fat, which comprised 25 and 7%, respectively, of energy intake. Serum LDL and HDL cholesterol and apoprotein B concentrations were higher in the group consuming the high-cholesterol diet (P < 0.05), but serum triacylglycerol, apo AI, and lipoprotein (a) did not differ between the 2 groups. The fractional clearance rate (FCR) of the 14C-CE emulsion, obtained by compartmental analysis, was 52% slower in the high-cholesterol than in the low-cholesterol group (P < 0.001); the 3H-TG FCR did not differ between the groups. Finally, we concluded that high cholesterol intakes increase the residence time of chylomicron remnants, as indicated by the 14C-CE kinetics, which may have undesirable effects related to the development of CAD. © 2006 American Society for Nutrition.

A Simple maxwell Based Model in Order to Represent the frequency-dependent viscosity measured by ultrasound

A previous work showed that viscosity values measured high frequency by ultrasound agreed with the values at low frequency by the rotational viscometer when conditions are met, such as relatively low frequency viscosity. However, these conditions strongly reduce the range of the measurement cell. In order to obtain a measurement range and sensitivity high frequency must used, but it causes a frequency-dependent decrease on the viscosity values. This work introduces a new simple in order to represent this frequency-dependent behavior.model is based on the Maxwell model for viscoelastic , but using a variable parameter. This parameter has physical meaning because it represents the linear behavior the apparent elasticity measured along with the viscosity by .Automotive oils SAE 90 and SAE 250 at 22.5±0.5oC viscosities at low frequency of 0.6 and 6.7 Pa.s, respectively,tested in the range of 1-5 MHz. The model was used in to fit the obtained data using an algorithm of non-linear in Matlab. By including the viscosity at low frequency an unknown fitting parameter, it is possible to extrapolate its . Relative deviations between the values measured by the and extrapolated using the model for the SAE 90 and SAE 250 oils were 5.0% and 15.7%, respectively.©2008 IEEE.

Experimental study of the complex reflection coefficient of shear waves from the solid-liquid interface

The determination of the reflection coefficient of shear waves reflected from a solid-liquid interface is an important method in order to study the viscoelastic properties of liquids at high frequency. The reflection coefficient is a complex number. While the magnitude measurement is relatively easy and precise, the phase measurement is very difficult due to its strong temperature dependence. For that reason, most authors choose a simplified method in order to obtain the viscoelastic properties of liquids from the measured coefficient. In this simplified method, inconsistent viscosity results are obtained because pure viscous behavior is assumed and the phase is not measured. This work deals with an effort to improve the experimental technique required to measure both the magnitude and phase of the reflection coefficient and it intends to report realistic values for oils in a wide range of viscosity (0.092 - 6.7 Pa.s). Moreover, a device calibration process is investigated in order to monitor the dynamic viscosity of the liquid.

Frequency of ABO blood group system polymorphisms in Plasmodium falciparum malaria patients and blood donors from the Brazilian Amazon region.

We investigated the ABO genotypes and heterogeneity of the O alleles in Plasmodium falciparum-infected and non-infected individuals from the Brazilian Amazon region. Sample collection took place from May 2003 to August 2005, from P. falciparum malaria patients from four endemic regions of the Brazilian Amazon. The control group consisted of donors from four blood banks in the same areas. DNA was extracted using the Easy-DNA(TM) extraction kit. ABO genotyping was performed using PCR/RFLP. There was a high frequency of ABO*O01O01. ABO*AO01 was the second most frequent genotype, and the third most frequent genotype was ABO*BO01. There were low frequencies of the ABO*O01O02, ABO*AA, ABO*AB, ABO*BB, and ABO*O02O02 genotypes. We analyzed the alleles of the O phenotype; the O(1variant) allele was the most frequent, both in malaria and non-malaria groups; consequently, the homozygous genotype O(1)(v)O(1)(v) was the most frequently observed. There was no evidence of the homozygous O(2) allele. Significant differences were not detected in the frequency of individuals with the various alleles in the comparison of the malaria patients and the general population (blood donors).

High-yield direct synthesis of Mg 2FeH 6 from the elements by reactive milling

Magnesium complex hydrides as Mg 2FeH 6 are interesting phases for hydrogen storage in the solid state, mainly due to its high gravimetric and volumetric densities of H2. However, the synthesis of this hydride is not trivial because the intermetallic phase Mg2Fe does not exist and Mg and Fe are virtually immiscible under equilibrium conditions. In this study, we have systematically studied the influence of the most important processing parameters in reactive milling under hydrogen (RM) for Mg 2FeH 6 synthesis: milling time, ball-to-powder weight ratio (BPR), hydrogen pressure and type of mill. Low cost 2Mg-Fe mixtures were used as raw materials. An important control of the Mg 2FeH 6 direct synthesis by RM was attained. In optimized combinations of the processing parameters, very high proportions of the complex hydride could be obtained. © (2011) Trans Tech Publications.

Sensitivity, specificity and predictive values of linear and nonlinear indices of heart rate variability in stable angina patients

Background: Decreased heart rate variability (HRV) is related to higher morbidity and mortality. In this study we evaluated the linear and nonlinear indices of the HRV in stable angina patients submitted to coronary angiography. Methods. We studied 77 unselected patients for elective coronary angiography, which were divided into two groups: coronary artery disease (CAD) and non-CAD groups. For analysis of HRV indices, HRV was recorded beat by beat with the volunteers in the supine position for 40 minutes. We analyzed the linear indices in the time (SDNN [standard deviation of normal to normal], NN50 [total number of adjacent RR intervals with a difference of duration greater than 50ms] and RMSSD [root-mean square of differences]) and frequency domains ultra-low frequency (ULF) ≤ 0,003 Hz, very low frequency (VLF) 0,003 - 0,04 Hz, low frequency (LF) (0.04-0.15 Hz), and high frequency (HF) (0.15-0.40 Hz) as well as the ratio between LF and HF components (LF/HF). In relation to the nonlinear indices we evaluated SD1, SD2, SD1/SD2, approximate entropy (-ApEn), α1, α2, Lyapunov Exponent, Hurst Exponent, autocorrelation and dimension correlation. The definition of the cutoff point of the variables for predictive tests was obtained by the Receiver Operating Characteristic curve (ROC). The area under the ROC curve was calculated by the extended trapezoidal rule, assuming as relevant areas under the curve ≥ 0.650. Results: Coronary arterial disease patients presented reduced values of SDNN, RMSSD, NN50, HF, SD1, SD2 and -ApEn. HF ≤ 66 ms§ssup§2§esup§, RMSSD ≤ 23.9 ms, ApEn ≤-0.296 and NN50 ≤ 16 presented the best discriminatory power for the presence of significant coronary obstruction. Conclusion: We suggest the use of Heart Rate Variability Analysis in linear and nonlinear domains, for prognostic purposes in patients with stable angina pectoris, in view of their overall impairment. © 2012 Pivatelli et al.; licensee BioMed Central Ltd.

Frequency of multiple endocrine neoplasia type 1 in a group of patients with pituitary adenoma: genetic study and familial screening

The purpose of this study it was to evaluate the frequency of Multiple Endocrine Neoplasia type 1 (MEN1) in patients with pituitary adenoma and to perform genetic analysis and familial screening of those individuals afflicted with MEN1. 144 patients with pituitary adenoma at Botucatu Medical School, UNESP-Univ Estadual Paulista, were assessed retrospectively for MEN1 during the years of 2005-2011. The patients were evaluated for the presence of primary hyperparathyroidism (PHP) and enteropancreatic tumors. Genetic analysis was performed for the individuals with clinically diagnosed MEN1. Thirteen patients met the diagnostic criteria for MEN1, but three individuals belong to the same family and they were considered as a single MEN1 event, revealing 7.7 % frequency of MEN1 in this patient group. Genetic analysis showed MEN1 mutations in four index cases: IVS4+1 G>A, IVS3-6 C>T, c.1547insC and a new D180A mutation. One patient did not agree to participate in the genetic study and another one was referred for follow up in other hospital. Only polymorphisms were found in the other individuals, one of which was novel. We identified a high frequency of MEN1 in pituitary adenoma patients. Since PHP is one of the most common MEN1 tumor and patients are mostly asymptomatic, we suggest that all pituitary adenoma patients have their calcium profile analyzed. © 2013 Springer Science+Business Media New York.

Time-frequency analysis combining wavelets and the envelope technique for fault identification in rotary machines

Nowadays the method based on demodulation by envelope finds wide application in industry as a technique for evaluation of bearings and other components in rotating machinery. In recent years the application of Wavelets for fault diagnosis in machinery has also obtained good development. This article demonstrates the effectiveness of the combined application of Wavelets and envelope technique (also known as HFRT High-Frequency Resonance Technique) to remove background noise from signals collected from defect bearings and identification of the characteristic frequencies of defects. A comparison of the results obtained with the isolated application of only one method against the combined technique is performed showing the increased capacity in detection of faults in rolling bearings. © (2013) Trans Tech Publications, Switzerland.

Pseudoautotomy in Dendrophidion dendrophis and Mastigodryas bifossatus (Serpentes: Colubridae): Tail Morphology and breakage frequency

The micro and macro structures of the caudal vertebrae and muscles of Dendrophidion dendrophis and Mastigodryas bifossatus were described using histological slides, dissections, radiographs, and clearing and double staining of intact, broken, and healed tails. To analyze the relationship among the frequencies of healed tails we established two populations of D. dendrophis and six groups of M. bifossatus. We found that fractures of the tail in the two species are intervertebral, and there are no morphological and/or structural mechanisms that facilitate the urotomy, which is classified as non-specialized pseudoautotomy. The caudal vertebrae of D. dendrophis and M. bifossatus show minor differences in the shape of the condyle, cotyle, and border of the neural spine, and in the size and orientation of the hemapophysis and pleurapophysis. The absence of bleeding at the moment of tail breakage may indicate the presence of sphincters in the veins and arteries of D. dendrophis. The distal part of the last vertebrae retained in healed tails of D. dendrophis and M. bifossatus participates in the healing processes as a possible source of calcium in the formation of a calcified cap. We found high frequency of tail breakage in both species, which occurs in almost the entire length of the tail, with no specific areas of concentration. There was no difference in the frequencies of healed tails among males and females of different populations of D. dendrophis and M. bifossatus. Juveniles have lower breakage frequencies than adults in both species, except for populations of M. bifossatus from the Cerrado and Pampa. © 2013 by the American Society of Ichthyologists and Herpetologists.