Development of experimental structure and influence of high CO2 concentration in maize cro

Maize is a C4 plant that shows few or no response to high [CO2]. Thus, this study aimed to analyze the photosynthetic rate and yield of maize under high [CO2] and develop open-top chambers (OTC) to create an atmosphere enriched with CO2. The experiment was conducted between October 2008 and March 2009. The OTCs were developed in modular scheme. Measurement of photosynthetic rates, transpiration, stomata conductance, grain yield and dry matter were performed. The experimental design was randomized blocks with four replications and three treatments: P1 - plants grown in OTC with 700 ppm [CO2], P2 - plants grown in OTC with environmental [CO2], and P3 - control, cultivated in open field. The results were analyzed by ANOVA and Tukey's test (Pr< 0.05). The chambers can reduce by 25% the photosynthetically active radiation and increase the air and leaf temperatures. Plants under high [CO2] (P1) showed the highest photosynthetic rates and the lowest stomata conductance and transpiration. The total weight of grains (g) and dry mass of shoots (g) showed no increases for P1, despite their higher photosynthetic rates.

Crop residues on short-term CO2 emissions in sugarcane production areas

The proper management of agricultural crop residues could produce benefits in a warmer, more drought-prone world. Field experiments were conducted in sugarcane production areas in the Southern Brazil to assess the influence of crop residues on the soil surface in short-term CO2 emissions. The study was carried out over a period of 50 days after establishing 6 plots with and without crop residues applied to the soil surface. The effects of sugarcane residues on CO2 emissions were immediate; the emissions from residue-covered plots with equivalent densities of 3 (D50) and 6 (D100) t ha-1 (dry mass) were less than those from non-covered plots (D0). Additionally, the covered fields had lower soil temperatures and higher soil moisture for most of the studied days, especially during the periods of drought. Total emissions were as high as 553.62 ± 47.20 g CO2 m-2, and as low as 384.69 ± 31.69 g CO2 m-2 in non-covered (D0) and covered plot with an equivalent density of 3 t ha-1 (D50), respectively. Our results indicate a significant reduction in CO2 emissions, indicating conservation of soil carbon over the short-term period following the application of sugarcane residues to the soil surface.

Influences of two CO2 concentrations and water availability on bean crop

This study was carried out to determine some physiological and phenological responses of the bean under high [CO2] and drought stress. The experiment was conducted from April to July 2009 in Viçosa, Brazil. The open-top chambers were used to enrich the air with CO2, whereas the drought stress was applied between the flowering and the ripening. The randomized block design was used, with four replicates in the subplots. The following plots were [CO2] at 700ppm (F1) and [CO2] environmental (F2) and the subplots were well watering (S1) and drought stress (S2). The results were subjected to Anova and the Tukey test (P < 0.05). For the treatments F1S1 and F1S2 the photosynthetic rate showed increments of 59% and the transpiration reduction of 12%. The yield, leaf temperature and stomatal conductance were not significant different to high [CO2], different from the dry matter, who showed increment of 20% (F1S1) and the water use efficiency who showed increase of 90% for high [CO2]. The osmotic potential was lower in plants under drought stress (F2S2 and F1S2), followed by plants under high [CO2] (F1S1). Despite the increment in photosynthesis, high [CO2] does not guarantee higher yield.

Emissão de CO2 do solo associada à calagem em área de conversão de laranja para cana-de-açúcar

A emissão de CO2 do solo (FCO2) em áreas agrícolas é resultante da interação de diversos fatores, sendo alterada pela prática de manejos do solo e da cultura, além das condições edafoclimáticas locais. Neste estudo, objetivou-se quantificar a FCO2 em função da calagem e posição da aplicação (antiga linha e entrelinha) da cultura da laranja em área de conversão para a cultura da cana-de-açúcar, no município de Frutal-MG. Os tratamentos avaliados foram: Linha/CC (linha com aplicação de calcário); Entrelinha/CC (entrelinha com aplicação de calcário); Linha/SC (linha sem aplicação de calcário), e Entrelinha/SC (entrelinha sem aplicação de calcário). FCO2, temperatura do solo (Ts) e umidade do solo (Us) foram avaliadas durante 12 dias. O maior valor médio da FCO2 ao longo do período de estudo foi observado no tratamento Linha/CC (9,63 µmol m-2 s-1); e o menor, no tratamento Entrelinha/CC (5,92 µmol m-2 s-1), segundo teste de Tukey. A FCO2 foi negativamente correlacionada à Us na Linha/CC (r = - 0,56; p < 0,05) e na Linha/SC (r = - 0,66; p < 0,05). Entre a FCO2 e a Ts, verificou-se correlação positiva e significativa na Linha/CC (r = 0,76; p < 0,001), na Linha/SC (r = 0,89; p < 0,001) e na Entrelinha/SC (r = 0,66; p < 0,05). Observou-se que a calagem e a posição de aplicação (linha e entrelinha) influenciaram nas emissões de CO2 do solo.

Leaf concentrations of nitrogen and phosphorus in phaseolus vulgaris l. Plants under high CO2 concentration and drought stress

This study aims to evaluate the leaf concentration of nitrogen and phosphorus correlated to the production of photoassimilates in beans plants (Phaseolus vulgaris L.) under high [CO2] and drought stress. The experiment was conducted in Viçosa (Brazil), during the period from April to July 2009, by using open-top chambers equipped with CO2 injection system. The drought stress was applied, through the irrigation suspension, during the period from flowering to maturation. The experimental design was randomized blocks in split-plot scheme with four replication, where the plots with plants grown in [CO2] of 700 mg L-1 and [CO2] environment of 380 mg L-1 and the subplots with plants with and without drought stress. The results were submitted to ANOVA and Tukey test (p < 0.05). In the plants under high [CO2] with and without drought stress, the photosynthetic rate increased by 59%, while the dry matter presented an increment of 20% in the plants under high [CO2] without drought stress. Reductions in [N] and [P] occurred in plants grown under high [CO2], resulting in greater efficiency in nitrogen use for photosynthesis. The high [CO2] increase only the total dry matter and not the total mass of grains. The drought stress reduces the dry matter and mass of grain, even at high [CO2].

Avaliação citométrica dos adipócitos localizados no tecido subcutâneo da parede anterior do abdome após infiltração percutânea de CO2

OBJETIVO: Avaliar os efeitos da infiltração de dióxido de carbono em adipócitos presentes na parede abdominal. MÉTODOS: Quinze voluntárias foram submetidas a sessões de infusão de CO2 durante três semanas consecutivas (duas sessões por semana com intervalos de dois a três dias entre cada sessão). O volume de gás carbônico infundido por sessão, em pontos previamente demarcados, foi sempre calculado com base na superfície da área a ser tratada, com volume infundido fixo de 250 mL/100cm² de superfície tratada. Os pontos de infiltração foram demarcados respeitando-se o limite eqüidistante 2cm entre eles. Em cada ponto se injetou 10mL, por sessão, com fluxo de 80mL/min. Foram colhidos fragmentos de tecido celular subcutâneo da parede abdominal anterior antes e após o tratamento. O número e as alterações histomorfológicas dos adipócitos (diâmetro médio, perímetro, comprimento, largura e número de adipócitos por campos de observação) foram mensurados por citometria computadorizada. Os resultados foram analisados com o teste t de Student pareado, adotando-se nível de significância de 5% (p<0,05). RESULTADOS: Encontrou-se redução significativa no número de adipócitos da parede abdominal e na área, diâmetro, perímetro, comprimento e largura após o uso da hipercapnia (p=0,0001). CONCLUSÃO: A infiltração percutânea de CO2 reduz a população e modifica a morfologia dos adipócitos presentes na parede abdominal anterior.

Biópsia hepática e peritoneal por laparoscopia ou por notes em suínos: comparação de parâmetros operatórios e evolução pós-operatória

OBJETIVO: Avaliar o impacto do NOTES, comparado à cirurgia laparoscópica, mediante análise de parâmetros fisiológicos além de complicações operatórias e evolução pós-operatória. MÉTODOS: Foram utilizados 12 suínos fêmeas, distribuídas em dois grupos: grupo laparoscopia (Glap) e grupo NOTES (GNotes). Os animais foram submetidos à biópsia hepática e peritoneal laparoscópica ou via endoscópica transvaginal. A cada 10 minutos foram anotadas a frequência respiratória, frequência cardíaca, saturação de O2 e concentração expiratória de CO2. No 7° PO, os animais foram submetidos à laparotomia para avaliação de complicações intra-abdominais. RESULTADOS: A maioria dos animais apresentou perda ponderal após o procedimento, entretanto em nenhum caso superior a 5%. Não houve diferença na variação percentual do peso entre os grupos (p=0,7535). Também não foram observadas diferenças ao se comparar as médias da ETCO2 (p=0,4762), e médias da FC (p=0,6035). Entretanto, o GLap apresentou médias de FR superiores ao GNotes (p=0,0043) assim como as médias da saturação de O2 (p=0,0080) foram superiores. Porém, nenhum animal apresentou satO2 inferior a 87% e esta diferença não foi considerada clinicamente significante. Apenas um animal do GNotes apresentou complicação operatória. CONCLUSÃO: NOTES está associado a parâmetros fisiológicos operatórios semelhantes aos encontrados na cirurgia laparoscópica A realização de peritonioscopia transvaginal não está associada a aumento das complicações operatórias comparado à laparoscopia.

Avaliação dos parâmetros gasométricos dos traumatizados durante o atendimento pré-hospitalar móvel

OBJETIVO: avaliar diferenças gasométricas dos pacientes traumatizados graves que necessitaram de intubação orotraqueal no atendimento pré-hospitalar. MÉTODOS: foram colhidas amostras de sangue dos pacientes que necessitaram de manejo de via aérea no início do atendimento pré-hospitalar e ao dar entrada na Unidade de Urgência. Foram analisados: pH, pressão arterial de CO2 (PaCO2), pressão arterial de O2 (PaO2), excesso de base (BE), saturação da hemoglobina por O2 (satO2) e a relação PaO2 e a fração inspirada de O2 (PaO2/FiO2). RESULTADOS: houve significância estatística entre as diferenças das médias entre os dados coletados no local do sinistro e na entrada da UUE na Frequência respiratória (p=0,0181), na Escala de Coma de Glasgow (p=0,0084), na pressão parcial arterial de oxigênio (PaO2; p<0,0001) e na saturação da hemoglobina pelo oxigênio (p=0,0018). CONCLUSÃO: a intubação orotraqueal altera os parâmetros PaO2 e saturação de oxigênio pela hemoglobina. Não houve diferença nos parâmetros metabólicos (pH, Bicarbonato e excesso de base). Na análise dos parâmetros hemogasométricos dos sobreviventes e não sobreviventes observou-se diferença estatística entre o PaO2, saturação de oxigênio pela hemoglobina e excesso de base.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

CO2 sparging for improving the filtration properties of iron ore slurries

Iron ore treatment processes are usually continuous and high tonnage and filtration equipment has to meet these requirements. In magnetite (Fe3O4) treatment process continuous rotary disc filters are often used for filtration. Carbon dioxide (CO2) treatment is a fairly novel and un-known filtration enhancing process. The interest to use CO2 is quite high because CO2 is a greenhouse gas that is abundant, readily available and capture and use of CO2 would be environmentally beneficial. The focus of this thesis was to investigate if CO2 could be used to enhance the filtration of magnetite with ceramic disc filter. Previous studies have suggested that CO2 could be used to enhance the filtration properties of different iron ores thus increasing the filtration capacity. In the literature part, the basic theory of filtration and the particle properties affecting filtration were discussed. The basic steps of a typical ore treatment process were presented. The reasons why CO2 might enhance the filtration properties of different ores were investigated. A literature survey of earlier studies of CO2 addition as a filter aid was presented and the basic chemical properties and reactions of CO2 were also discussed. The experimental part was done at the LUT Laboratory of Separation Technology using different magnetite samples from the industry. The filtration experiments indicated that CO2 had a positive influence on the filtration properties of magnetite slurry. Zeta potential of untreated and CO2 treated magnetite was measured and CO2 treated magnetite had lower zeta potential values than the untreated magnetite. The filtration capacity was increased while the cake moisture levels were only slightly increased.

Valmistusteknillinen näkökulma hitsattaessa ruostumattomia teräksiä CO2-laserilla

Tämä kandidaatintyö on valmistuksellinen näkökulma ruostumattoman teräksen CO2-laserhitsauksen perusteisiin. Tavoitteena on perehdyttää lukija ruostumattoman teräksen CO2-laserhitsauksen valmistusteknillisiin vaatimuksiin ja teollisuuden sovelluksiin.

The seasonal and ovarian status effects on in vitro production of domestic cat embryos between Equator and Tropic of Capricorn

From the Tropic of Capricorn to Equator, the seasonality of domestic cat is known to be absent, i.e., these animals are considered non-seasonal breeders at these regions. We hypothesized that this particularity might have some influence on in vitro embryo production. The aim of this experiment was to determine the percentage of cleavage and morulae and blastocyst formation produced from oocytes recovered from queen ovaries of three distinct status - follicular, luteal or inactive - during two different reproductive seasons experienced by cats in southeast of Brazil (22°53'09" S and 48°26'42" W) - non breeding season (NBS), comprehending January to March; and breeding season (BS), August to October. Thirty queens were neutered. Ovaries were classified according to their status and were sliced in PBS for cumulus oocyte complex (COC) releasing. Grade I COC were washed three times in H-MEM supplemented with BSA, glutamine, sodium pyruvate, cysteine, streptomycin and penicillin. Oocytes were incubated in groups of 20-30 in 400µL of DMEM supplemented with FSH, LH, estradiol, IGF-I and basic fibroblast growth factor under mineral oil for 30 or 36 hours at 38°C in humidified environment of 5% de O2, 5% CO2 and 90% N2. COC were fertilized in Ham's F-10 medium supplemented with BSA, cysteine, pyruvate and streptomycin/penicillin (culture medium) with fresh semen selected through swim up technique. Eighteen hours later, the presumptive zygotes were denuded, the percentage of cleavage was determined and every 10 zygotes were transferred to 100mL drops of culture medium for culture during three days. After 72 hours of culture the percentage of morulae formation was evaluated and these structures were transferred to drops of the same culture medium. At the eighth day of culture blastocyst formation was analyzed. During NBS, from a total of 272 (inactive), 162 (luteal) and 134 (follicular) fertilized oocytes, the percentage of cleaved zygotes, morulae and blastocysts derived from inactive ovaries were 24.63, 16.54 and 8.09 respectively; for those derived from luteal ovaries, the percentage was 21.6, 12.96 and 8.64, and for those from follicular ovaries, they were 24.62, 16.41 and 8.21. Considering BS, from a total of 102 (inactive), 198 (luteal) and 86 (follicular) fertilized oocytes, the relative frequency (%) of cleaved zygotes, morulae and blastocysts derived from inactive ovaries were 64.7, 41.17 and 23.53 respectively; for those derived from luteal ovaries, the percentage was 64.14, 40.41 and 23.73, and for those from follicular ovaries, they were 63.95, 39.54 and 24.41. The results of this experiment demonstrate that no statistically significant difference (P<0.05) was verified in the frequency of cleaved embryos and morulae and blastocyst formation when comparing the three ovarian conditions in the same season. However the breeding season presented better results considering cleavage and morulae and blastocyst formation.

Thermal radiation in combustion systems

A numerical procedure for solving the nongray radiative transfer equation (RTE) in two-dimensional cylindrical participating media is presented. Nongray effects are treated by using a narrow-band approach. Radiative emission from CO, CO2, H2O, CH4 and soot is considered. The solution procedure is applied to study radiative heat transfer in a premixed CH4-O2, laminar, flame. Temperature, soot and IR-active species molar fraction distributions are allowed to vary in the axial direction of the flame. From the obtained results it is possible to quantify the radiative loss in the flame, as well as the importance of soot radiation as compared to gaseous radiation. Since the solution procedure is developed for a two-dimensional cylindrical geometry, it can be applied to other combustion systems such as furnaces, internal combustion engines, liquid and solid propellant combustion.

Efeito da pressurização com CO2 sobre o pH da água

Durante a fase de desenvolvimento de novos produtos fitossanitários é comumente utilizado o pulverizador a pressão constante, pressurizado com CO2. O gás carbônico pode provocar a acidificação da água e afetar o comportamento do composto que está sendo avaliado. No presente trabalho, amostras de água de 30 diferentes fontes foram pressurizadas com CO2 durante cinco minutos, até 275 kPa (40 lbf/pol.2), e o pH foi medido na água que saiu do bico e na água no inteior do tanque do pulverizador. Os resultados mostraram redução nos valores do pH em toda as amostras . Os valores do pH elevaram-se ligeiramente após a saída da água pelo bico do pulverizador. A redução, em alguns casos, foi marcante, atingindo 4,91 unidades de pH no caso mais drástico. Esses dados levam a recomendar cautela na interpretação dos resultados obtidos com o uso dos pulverizadores pressurizados com o gás carbônico.

Liberação de CO2, biomassa microbiana e fósforo disponível em solo adicionado de matéria seca de poaia-branca

O presente experimento, inteiramente casualizado, foi desenvolvido em condições de laboratório no Departamento de Defesa Fitossanitária, FCA/UNESP - Botucatu, entre julho e setembro de 1992. Amostras de Areia Quartzosa equivalentes à 40 g de terra seca à 105 oC ± 2 com ou sem adição de 1,9 g de matéria seca de plantas de poaia-branca (Richardia brasiliensis), 0,19 g de nitrogênio (NH4)2SO4 e 0,88 g de apatita de Araxá, foram incubadas no escuro a 25 o C ± 2 , com umidade mantida a 60% da capacidade de retenção de água. Durante a incubação, determinou-se o CO2 liberado, utilizando-se o método de retenção em NAOH seguida de titulometria com HCl; a biomassa microbiana, método de fumigação-incubação; o pH e a quantidade de fósforo extraído por resina. A maior liberação de CO2 ocorreu durante os dez primeiros dias de incubação, com 77% do total de carbono liberado nos tratamentos com adição de poaia, e 37% nos tratamentos sem adição da mesma. A liberação de CO2 foi 57 vezes maior nos tratamentos com poaia em relação ao controle. A poaia também provocou aumentos na biomassa microbiana (média de 8 vezes a biomassa do tratamento controle), e a adição de nitrogênio e/ou fosfato de rocha junto à poaia antecipou os picos de formação de biomassa de 20 para 10 dias de incubação. Os níveis de fósforo disponível foram maiores no tratamento com adição de fosfato de rocha apenas. A poaia também alcalinizou o sistema, não permitindo desta forma, observar-se relação significativa entre pH e teor de fósforo disponível.