Resistance of alkali activated slag concretes to chloride environments based on chloride penetration measurements

ABSTRACT

One of the binder systems with low environmental footprint is alkali activated slag concretes (AASC), made by adding alkalis such as sodium hydroxide and sodium silicate to industrial by-products such as ground granulated blast furnace slag (GGBS). Whilst they have the similar behaviour as that of traditional cement systems in terms of strength and structural behaviour, AASC do exhibit superior performance in terms of abrasion and acid resistance and fire protection.
In this article, the authors focus their attention on chloride ingress into different grades of AASC. The mix variables in AASC included water-to-binder, binder to aggregate ratio, percentage of alkali and the SiO2/Na2O ratio (silica modulus, Ms). The first challenge is to get mixes for different range of workability (with slump values from 40mm to 240mm) and reasonable early age and long term compressive strength according to each one. Then the chloride diffusion and migration in those mixes were measured and compared with same normal concretes in the existed literature based on chloride penetration depth. Comparing the chloride ingress between tradition concretes and AASCs is worthwhile to prove the possibility of increasing concrete lifetime in proximity to sea and deciding while such concretes are practical for use. Findings show that compared to the PC concretes, the AAS concretes have lower rate of chloride ingress.

Resistance of alkali activated slag concretes to chloride environments

ABSTRACT: Researchers are focusing their attention on alternative binder systems using 100% supplementary cementitious materials as it allows better control over the microstructure formation and low to moderate environmental footprint. One such system being considered is alkali activated slag concretes (AASC), made by adding alkalis such as sodium hydroxide and sodium silicate to ground granulated blast furnace slag (GGBS). Whilst they have a similar behaviour as that of traditional cement systems in terms of strength and structural behaviour, AASC are reported to exhibit superior performance in terms of abrasion,acid resistance and fire protection.
In this article, the authors investigate chloride ingress into different grades of AASC. The mix variables in AASC included water to binder, and binder to aggregate ratio, percentage of alkali and the SiO2/Na2O ratio (silica modulus, Ms). The first challenge was to develop mixes for different range of workability (with slump values from 40mm to 240mm) and reasonable early age and long term compressive strength. Further chloride ingress into those mixes were assessed and compared with the data from normal concretes based on literature. Findings show that compared to the PC concretes, the AAS concretes have lower rate of chloride ingress.

Oxygen and Chloride Permeability of Alkali-Activated Natural Pozzolan Concrete

One of the important factors in the use of portland cement concrete is its durability, and most of the situations where durability is lacking have been identifi ed and strategies to manage durability have been implemented. Geopolymer concrete, made from an alkali-activated natural pozzolan (AANP), provides an important opportunity for the reduction of carbon dioxide (CO2) emissions associated with the manufacture of concrete but has a limited history of durability studies. Until its different properties are well understood there is no desire to adopt this new technology of unknown provenance by the concrete industry. This paper presents an experimental study of oxygen and chloride permeability of AANP concrete prepared by activating Taftan andesite and Shahindej dacite (Iranian natural pozzolans), with and without calcining, and the correlations between these properties and compressive strength. The results show that compared to ordinary portland cement (OPC) concrete, AANP concrete has lower oxygen permeability at later ages; but it shows moderate to high chloride ion penetrability.

Contribuicao ao conhecimento dos efeitos da radiacao em cristais de KCl com impurezas de Sr

Tese (Doutoramento)

Estimating Natural Recharge by Means of Chloride Mass Balance in a Volcanic Aquifer: Northeastern Gran Canaria (Canary Islands, Spain)

[EN]The chloride mass balance method was used to estimate the average diffuse groundwater recharge on northeastern Gran Canaria (Canary Islands), where the largest recharge to the volcanic island aquifer occurs. Rainwater was sampled monthly in ten rainwater collectors to determine the bulk deposition rate of chloride for the 2008–2014 period. Average chloride deposition decreases inwardly from more than 10 g·m−2 ·year−1 to about 4 g·m−2 ·year−1 . The application of the chloride mass balance method resulted in an estimated average recharge of about 28 hm3 /year or 92 mm/year (24% of precipitation) in the study area after subtracting chloride loss with surface runoff.

Influence of grinding operations on surface integrity and chloride induced stress corrosion cracking of stainless steels

Stainless steels were developed in the early 20th century and are used where both the mechanical properties of steels and corrosion resistance are required. There is continuous research to allow stainless steel components to be produced in a more economical way and be used in more harsh environments. A necessary component in this effort is to correlate the service performance with the production processes. The central theme of this thesis is the mechanical grinding process.  This is commonly used for producing stainless steel components, and results in varied surface properties that will strongly affect their service life. The influence of grinding parameters including abrasive grit size, machine power and grinding lubricant were studied for 304L austenitic stainless steel (Paper II) and 2304 duplex stainless steel (Paper I). Surface integrity was proved to vary significantly with different grinding parameters. Abrasive grit size was found to have the largest influence. Surface defects (deep grooves, smearing, adhesive/cold welding chips and indentations), a highly deformed surface layer up to a few microns in thickness and the generation of high level tensile residual stresses in the surface layer along the grinding direction were observed as the main types of damage when grinding stainless steels. A large degree of residual stress anisotropy is interpreted as being due to mechanical effects dominating over thermal effects. The effect of grinding on stress corrosion cracking behaviour of 304L austenitic stainless steel in a chloride environment was also investigated (Paper III). Depending on the surface conditions, the actual loading by four-point bend was found to deviate from the calculated value using the formula according to ASTM G39 by different amounts. Grinding-induced surface tensile residual stress was suggested as the main factor to cause micro-cracks initiation on the ground surfaces. Grinding along the loading direction was proved to increase the susceptibility to chloride-induced SCC, while grinding perpendicular to the loading direction improved SCC resistance. The knowledge obtained from this work can provide a reference for choosing appropriate grinding parameters when fabricating stainless steel components; and can also be used to help understanding the failure mechanism of ground stainless steel components during service.

Sub lethal mercuric chloride toxicity induced stress related alterations in the epithelial lining of foot of the freshwater mussel Lamellidens marginalis (Lamarck)

Sub lethal (0.2 ppm) mercuric chloride induced stress related histopathological alterations in the epithelial linings of foot (podium) of the edible freshwater mussel Lamellidens marginalis (Lamarck) were studied using histochemical techniques up to 60 days of exposure. The histomorphological changes were manifested only slowly and its intensity was somewhat proportional to the duration of exposure. The immediate response of the exposed mussels was the altered mucous secretion. There was a progressive incorporation of sulphated glycoproteins into the secretory contents of the mucous cells especially in the first half of the experiment. Marked histopathological changes including necrosis, appearance of pyknotic nuclei, sloughing of epithelial cells and appearance of non-tissue spaces, etc., started appearing during the later half of the experiment. The fag end of the experiment, which witnessed prominent histomorphological changes, was accompanied by highly decreased mucous secretion. KEYWORDS: heavy metal toxicity, mercuric chloride, Lamellidens marginalis, freshwater mussel, histopathology.

Queijo minas padrão com reduzido teor de sódio: composição e caracterização sensorial

Sodium is an essential nutrient with important functions in the organism, however, its ingestion in excess may cause various health problems such as arterial hypertension, brain diseases, heart failure and chronic renal failure. In this context, the present study proposes to prepare Minas Padrão cheese with different contents of sodium with the objective of evaluating the effect of the addition of potassium chloride in sensory characteristics and hysicochemical properties, as well as in the proximal composition and in microbiological quality. The cheeses were elaborate in concentrations of 100% of NaCl (C), 80% of NaCl + 20% of KCl (T1), 60% of NaCl + 40% of KCl (T2), 40% of NaCl + 60% of KCl (T3) and 20% of NaCl + 80% of KCl (T4) and stored for 20 days at 10 ºC. The proximal composition and physicochemical was based on the determination of moisture content, fat, protein, ash, chloride, sodium, potassium, titratable acidity and pH of all treatments after 20 days of storage. The microbiological quality of the samples was monitored through the count of Total Coliforms and Escherichia coli, Staphylococcus aureus, Salmonella spp., mold and yeast in the first and fifteenth day of storage. The sensorial characterization was performed by the technique of Free Profile choice. The results showed that the replacement of sodium chloride by potassium in the Minas Padrão cheese in concentration higher than 40% presented significantly higher moisture contents. Cheese with a reduction greater than 60% of sodium obtained significantly effect in the titratable acidity, presenting higher values compared to the other treatments. The cheese with 20% of salt replacement did not differ statistically in relation to the control. When the proportion of substituent was increased, a significant reduction of the sodium content of up to 73% was observed. As the sodium was replaced by potassium in cheese, the potassium content increased significantly, stablishing a reduction of 82% in relation to the control. There was no effect to sodium substitution by potassium in fat, protein, ash and chlorides, as well as the pH values. The microbiological results were in accordance with the current legislation, therefore suitable to be eaten. According to the Free Profile Choice technique it was observed that the control C cheese (100% of NaCl) showed results very close to the other treatments, differing only in flavor attributes. The replacement of sodium by potassium in proportions of 20% contributed to a bitter taste detected by the tasters. Whereas, the appearance, flavor and texture attributes showed no significant differences compared to the Minas Padrão cheese.

The regulation of cancer cell invasive behaviour by Chloride Interacellular Channel 3 (CLIC3) and Transglutaminasae 2

A study into the role of secreted CLIC3 in tumour cell invasion. The initiation and progression of cancers is thought to be linked to their relationship with a population of activated fibroblasts, which are associated with tumours. I have used an organotypic approach, in which plugs of collagen I are preconditioned with fibroblastic cells, to characterise the mechanisms through which carcinoma-associated fibroblasts (CAFs) influence the invasive behaviour of tumour cells. I have found that immortalised cancer-associated fibroblasts (iCAFs) support increased invasiveness of cancer cells, and that this is associated with the ability of CAFs to increase the fibrillar collagen content of the extracellular matrix (ECM). To gain mechanistic insight into this phenomenon, an in-depth SILAC-based mass proteomic analysis was conducted, which allowed quantitative comparison of the proteomes of iCAFs and immortalised normal fibroblast (iNFs) controls. Chloride Intracellular Channel Protein 3 (CLIC3) was one of the most significantly upregulated components of the iCAF proteome. Knockdown of CLIC3 in iCAFs reduced the ability of these cells to remodel the ECM and to support tumour cell invasion through organotypic plugs. A series of experiments, including proteomic analysis of cell culture medium that had been preconditioned by iCAFs, indicated that CLIC3 itself was a component of the iCAF secretome that was responsible for the ability of iCAFs to drive tumour cell invasiveness. Moreover, addition of soluble recombinant CLIC3 (rCLIC3) was sufficient to drive the extension of invasive pseudopods in cancer cell lines, and to promote disruption of the basement membrane in a 3D in vitro model of the ductal carcinoma in situ (DCIS) to invasive ductal carcinoma (IDC) transition. My investigation into the mechanism through which extracellular CLIC3 drives tumour cell invasiveness led me to focus on the relationship between CLIC3 and the ECM modifying enzyme, transglutaminase-2 (TG2). Through this, I have found that TG2 physically associates with CLIC3 and that TG2 is necessary for CLIC3 to drive tumour cell invasiveness. These data identifying CLIC3 as a key pro-invasive factor, which is secreted by CAFs, provides an unprecedented mechanism through which the stroma may drive cancer progression.

Calcium response of KCl-excited populations of ventricular myocytes from the European sea bass (Dicentrarchus labrax): a promising approach to integrate cell-to-cell heterogeneity in studying the cellular basis of fish cardiac performance

Climate change challenges the capacity of fishes to thrive in their habitat. However, through phenotypic diversity, they demonstrate remarkable resilience to deteriorating conditions. In fish populations, inter-individual variation in a number of fitness-determining physiological traits, including cardiac performance, is classically observed. Information about the cellular bases of inter-individual variability in cardiac performance is scarce including the possible contribution of excitation-contraction (EC) coupling. This study aimed at providing insight into EC coupling-related Ca2+ response and thermal plasticity in the European sea bass (Dicentrarchus labrax). A cell population approach was used to lay the methodological basis for identifying the cellular determinants of cardiac performance. Fish were acclimated at 12 and 22 A degrees C and changes in intracellular calcium concentration ([Ca2+](i)) following KCl stimulation were measured using Fura-2, at 12 or 22 A degrees C-test. The increase in [Ca2+](i) resulted primarily from extracellular Ca2+ entry but sarcoplasmic reticulum stores were also shown to be involved. As previously reported in sea bass, a modest effect of adrenaline was observed. Moreover, although the response appeared relatively insensitive to an acute temperature change, a difference in Ca2+ response was observed between 12- and 22 A degrees C-acclimated fish. In particular, a greater increase in [Ca2+](i) at a high level of adrenaline was observed in 22 A degrees C-acclimated fish that may be related to an improved efficiency of adrenaline under these conditions. In conclusion, this method allows a rapid screening of cellular characteristics. It represents a promising tool to identify the cellular determinants of inter-individual variability in fishes' capacity for environmental adaptation.

Regulation of epithelial chloride transport by tyrosine phosphorylation

Background: Chloride transport proteins are involved in a variety of human diseases and thus represent important drug targets. They are regulated in part through the amount present at the plasma membrane and tyrosine phosphorylation has been described as a novel regulator.

[(3-Chlorobenzamido)methyl]triethylammonium chloride

We report the synthesis of [(3-chlorobenzamido)methyl]triethylammonium chloride in a reaction of N-(chloromethyl)-3-chlorobenzamide and triethylamine in dry acetone. The structure of the newly synthesized compound was characterized with1H-NMR,13C-NMR, FTIR and Mass spectroscopy. © 2015 by the authors; licensee MDPI, Basel, Switzerland.

Effect of the cation on the interactions between alkyl methyl imidazolium chloride ionic liquids and water

A systematic study of the interactions between water and alkyl methyl imidazolium chloride ionic liquids at 298.2 K, based on activity coefficients estimated from water activity measurements in the entire solubility range, is presented. The results show that the activity coefficients of water in the studied ILs are controlled by the hydrophilicity of the cation and the cation-anion interaction. To achieve a deeper understanding on the interactions between water and the ILs, COSMO-RS and FTIR spectroscopy were also applied. COSMO-RS was used to predict the activity coefficient of water in the studied ionic liquids along with the excess enthalpies, suggesting the formation of complexes between three molecules of water and one IL molecule. On the basis of quantum-chemical calculations, it is found that cation-anion interaction plays an important role upon the ability of the IL anion to interact with water. The changes in the peak positions/band areas of OH vibrational modes of water as a function of IL concentration were investigated, and the impact of the cation on the hydrogen-bonding network of water is identified and discussed.

Volumetric interactions of a series of α-amino acids in aqueous magnesium chloride solutions at 278.15, 288.15, 298.15, and 308.15 K

In this work, the partial molar volumes of glycine, l-alanine, l-valine, l-serine, and l-threonine in aqueous solutions of magnesium chloride at 0.0, 0.1, 0.3, 0.7, and 1.0 molal are addressed between 278.15 and 308.15 K. Volumes of transfer were obtained, following the rank serine > glycine a parts per thousand threonine > alanine > valine. Differently, the hydration numbers follow the sequence serine > valine > alanine > threonine > glycine, and dehydration of the amino acids is observed, rising the temperature or salt molality. The data suggest that interactions are mainly pairwise, between the ions and charged/hydrophilic groups of the amino acids. Within the Friedman and Krishnan formalism, a group-contribution scheme has been successfully applied to the pairwise volumetric interaction coefficient. Finally, the dehydration effect of MgCl2 on glycine, alanine, and serine has been predicted applying empirical correlations developed before, showing satisfactory results.