Nova contribuiçao ao conhecimento da formação Rio Claro (T) na Folha Rio Claro (SP)

The Rio Claro Formation mainly occurs in the county of Rio Claro (SP) lying unconformably on Paleozoic and Mesozoic rocks. Its thickness is 30-40 m. It shows fine to coarse, regular to poor sorted, Triable sandstones and conglomerates with quartzite and quartz clasts in the base. Thin layers of mudstone occur interbeded. Stratigraphic maps had been elaborated in recent analyses allowing to improve the knowledge about the formation. The biggest thicknesses occur on the east part of the studied area. The coarse/fine clastic ratio map demonstrates that fine sediments are concentrated in the east side, and suggests the existence of barriers which conditioned perennial water body (or bodies) where decantation took place (east, south and southeast sides). The structural contour map of the Rio Claro Formation base indicates a NW/SE trough which was the main depositional axis. The integrated analysis demonstrates that the formation is formed by lacustrine, fluvial and debris flows deposits whose source area was located on NW side, with coalescent alluvial fans from where braided to psamitic meandering fluvial channels came. The location of the source area suggests no link with the Corumbataf River paleo-terraces.

Effect of resin luting film thickness on fracture resistance of a ceramic cemented to dentin

Purpose: The aim of this study was to evaluate the fracture resistance of ceramic plates cemented to dentin as a function of the resin cement film thickness. Materials and Methods: Ceramic plates (1 and 2 mm thicknesses) were cemented to bovine dentin using resin composite cement. The film thicknesses used were approximately 100, 200, and 300 μm. Noncemented ceramic plates were used as control. Fracture loads (N) were obtained by compressing a steel indenter in the center of the ceramic plates. ANOVA and Tukey tests (α = 0.05) were used for each ceramic thickness to compare fracture loads among resin cement films used. Results: Mean fracture load (N) for 1-mm ceramic plates were: control - 26 (7); 100 μm - 743 (150); 200 μm - 865 (105); 300 μm - 982 (226). Test groups were significantly different from the control group; there was a statistical difference in fracture load between groups with 100 and 300 μm film thicknesses (p < 0.01). Mean fracture load for 2-mm ceramic plates were: control - 214 (111); 100 μm - 1096 (341); 200 μm - 1067 (226); 300 μm - 1351 (269). Tested groups were also significantly different from the control group (p < 0.01). No statistical difference was shown among different film thicknesses. Conclusions: Unluted specimens presented significantly lower fracture resistance than luted specimens. Higher cement film thickness resulted in increased fracture resistance for the 1-mm ceramic plates. Film thickness did not influence the fracture resistance of 2-mm porcelain plates. Copyright © 2007 by The American College of Prosthodontists.

Influence of microwave polymerization method and thickness on porosity of acrylic resin

Purpose: This study evaluated the influence of polymerization cycle and thickness of maxillary complete denture bases on the porosity of acrylic resin. Materials and Methods: Two heat-activated denture base resins - one conventional (Clássico) and one designed for microwave polymerization (Onda-Cryl) - were used. Four groups were established, according to polymerization cycles: A (Onda-Cryl, short microwave cycle), B (Onda-Cryl, long microwave cycle), C (Onda-Cryl, manufacturing microwave cycle), and T (Clássico, water bath). Porosity was evaluated for different thicknesses (2.0, 3.5, and 5.0 mm; thicknesses I, II, and III, respectively) by measurement of the specimen volume before and after its immersion in water. The percent porosity data were submitted to Kruskal-Wallis for comparison among the groups. Results: The Kruskal-Wallis test detected that the combinations of the different cycles and thicknesses showed significant differences, and the mean ranks of percent porosity showed differences only in the thinnest (2.0 mm) microwave-polymerized specimens (A = 53.55, B = 40.80, and C = 90.70). Thickness did not affect the results for cycle T (I = 96.15, II = 70.20, and III = 82.70), because porosity values were similar in the three thicknesses. Conclusions: Microwave polymerization cycles and the specimen thickness of acrylic resin influenced porosity. Porosity differences were not observed in the polymerized resin bases in the water bath cycle for any thickness. © 2007 by The American College of Prosthodontists.

Effect of collagenase ointment on a radiofrequency induced abrasive wound

• Aim: Radiofrequency is one of the methods used to treat wrinkles and skin lesions, but its application may result in an abrasive wound. The purpose of this study was to evaluate the effect of collagenase ointment on the epithelial healing of an abrasive wound induced by a radiofrequency system. • Methods: An abrasive wound was produced using radiofrequency at the dorsal midline of 30 guinea pigs, which were randomly divided into 2 groups: one group were treated with saline solution and the other group treated with collagenase ointment; both used twice daily. The animals were sacrificed at 1, 7, 15, 30 and 60 postoperative days. Macroscopic, histological and morphometric evaluations were performed and the results were submitted to statistical analysis. • Results: The animals treated with collagenase ointment presented accelerated healing process and less inflammatory cell infiltration than the saline solution treated animals from one to fifteen postoperative days. Morphometric evaluation showed a thicker epidermis and a thinner dermis layer in the saline solution group at one and seven postoperative days, but significant differences between both groups were not observed at thirty and sixty postoperative days. • Conclusion: According to our results the use of collagenase ointment may accelerate the healing process of a radiofrequency induced abrasive wound.

Obesidade e sintomas de depressão, ansiedade e desesperança em mulheres sedentárias e não sedentárias

The aim of this field study was to verify if there is a relation between obesity and symptoms of depression, anxiety and hopelessness in 40 women aged 30,35 on average (± 8,60), divided into two groups: non-sedentary ones, characterized for doing a physical activity at least three times a week for three weeks in a row and sedentary ones, characterized by not practicing any type of regular physical activity when recruited. The method consisted of: objective evaluations of humor, through Beck Inventories of Anxiety (BAI), Depression (BDI) and Hopelessness (BHS) and Physical Evaluation, including total body mass, height, waist and hip circumferences and skin folds thickness. Calculations of the body mass index (BMI), of the waist/hip index (WHI) and of the percentage of corporal fat (%F) were performed in order to evaluate the presence and level of obesity. Results of the analysis of regression to square minimum supported the initial hypothesis concerning the existence of a relation between obesity and psychic symptoms only in sedentary women (BDI/WHI, p=0,035, BDI/BMI, p=0,009, BDI/%G, p=0,019, BAI/BMI, p=0,009, BAI/%G, p=0,037, BHS/WHI, p=0,025, BHS/BMI, p=0,041), once the relation of dependency could not be confirmed in non-sedentary women BDI/WHI, p=0,750, BDI/BMI, p=0,141, BDI/%G, p=0,064, BAI/WHI, p=0,729, BAI/BMI, p=0,384, BAI/%G, p=0,246, BHS/WHI, p=0,491, BHS/BMI, p=0,986, BHS/%G, p=0,322) and the greater the level of obesity, the greater the level of psychic symptoms in both groups. These observations seem to point out that the practice of physical activities was a factor of minimization of presence and intensity of psychic symptoms in non-sedentary women.

Autologous orbicularis muscle for filling facial foldsan experimental and clinical study

Purpose: To present a technique for filling facial folds by using autologous orbicularis oculi muscle, based on an experimental model. Methods: two studies are presented: (1) an experimental study using 15 albino guinea-pigs from which a strip of the sural triceps muscle was removed and implanted in the subcutaneous tissue of the dorsal area. The animals were sacrificed 7, 30 and 60 days after the implantation, and the material was histologically evaluated. And (2%) an interventional prospective clinical trial carried out on 20 patients referred to blepharoplasty surgery. They received autologous preseptal orbicularis muscle for filling facial folds. The results where evaluated by patients satisfaction and clinical exam. Results: the sural tricep muscle, when implanted in the subcutaneous tissue, resulted in fibrosis. The patients whom received autologous orbicularis muscle implanted for filling facial folds showed that the procedure can be successfully carried out. Conclusions: autologous preseptal orbicularis muscle is a good material for filling facial folds. Cicatricial tissue will be formed on its implantation site, filling the tissue gap that forms the folds on the skin.

Comparison of GEANT4 simulations with experimental data for thick al absorbers

Proton beams in medical applications deal with relatively thick targets like the human head or trunk. Therefore, relatively small differences in the total proton stopping power given, for example, by the different models provided by GEANT4 can lead to significant disagreements in the final proton energy spectra when integrated along lengthy proton trajectories. This work presents proton energy spectra obtained by GEANT4.8.2 simulations using ICRU49, Ziegler1985 and Ziegler2000 models for 19.68MeV protons passing through a number of Al absorbers with various thicknesses. The spectra were compared with the experimental data, with TRIM/SRIM2008 and MCNPX2.4.0 simulations, and with the Payne analytical solution for the transport equation in the Fokker-Plank approximation. It is shown that the MCNPX simulations reasonably reproduce well all experimental spectra. For the relatively thin targets all the methods give practically identical results but this is not the same for the thick absorbers. It should be noted that all the spectra were measured at the proton energies significantly above 2MeV, i.e., in the so-called Bethe-Bloch region. Therefore the observed disagreements in GEANT4 results, simulated with different models, are somewhat unexpected. Further studies are necessary for better understanding and definitive conclusions. © 2009 American Institute of Physics.

A comparison of the film thickness of two adhesive luting agents and the effect of thermocycling on their microTBs to feldspathic ceramic.

The aim of the present study was to evaluate the effect of thermocycling (TC) on the microtensile bond strength (microTBS) of two luting agents to feldspathic ceramic and to measure their film thickness (FT). For the microTBS test, sixteen blocks (6.4 x 6.4 x 4.8 mm) were fabricated using a feldspathic ceramic, etched with 10% hydrofluoric acid, rinsed and treated with the silane agent. The ceramic blocks were divided into two groups (n= 8): Gr1: dual-cured resin cement and Gr2: flowable resin. The luting agents were applied on the treated surfaces. Microsticks (1 +/-0. 1mm2) were prepared and stored under two conditions: dry, specimens immediately submitted to the microTBS test, and TC (6,000 cycles; 5 degrees C-55 degrees C). The microTBS was evaluated using a universal testing machine (1 mm/min). The microTBS data (MPa) were submitted to two-way ANOVA and Tukey' test (5%). For the FT test (ISO 4049), 0.05 ml of each luting agent (n=8) was pressed between two Mylar-covered glass plates (150 N) for 180 seconds and light polymerized. FT was measured using a digital paquimeter (Model 727-2001). The data (mm) were submitted to one-way ANOVA. The luting cement did not influence the microTBS results (p= 0.4467). Higher microtensile bond values were found after TC (20.5 +/- 8.6 MPa) compared to the dry condition (13.9 +/- 4. 7MPa), for both luting agents. The luting agents presented similar film thicknesses: Gr1- 0.052 +/- 0.016 mm; Gr2-0.041 +/- 0.003 mm. The luting agents presented similar film thickness and microTBS values, in dry and TC conditions and TC increased the bond strength regardless of the luting agent.

A randomized and controlled trial about the use of oral isotretinoin for photoaging

Topical retinoids are used to treat photoaging; oral isotretinoin is gold standard for acne; off label indications, including photoaging, have been reported with insufficient evidence of efficacy. This is a randomized controlled phase II trial with clinical and histological assessment to evaluate efficacy and safety of oral isotretinoin for photoaging. Study population was comprised of 32 menopausal or sterilized women, aged 40-55, divided in 2 groups: A (21) received 20mg isotretinoin, 3 times per week, nightly moisturizer, and daily sunscreen, for three months; B (11) just moisturizer/sunscreen. Main outcome measures were: overall clinical assessment; profilometry, corneometer and elasticity tests in periocular regions and left forearm; before/after biopsies from left forearm in patients of B and in 10 randomly selected of A. Microscopic blinded evaluation of epidermal thickness, dermal elastosis, new collagen, p53 epidermal expression was performed by quantitative digital image analysis. All data were submitted to statistical analysis. Clinical evaluation showed slight improvement; profilometry, corneometer and skin elasticity tests presented significant difference in pre/post values (P = 0.001 to 0.028), but no differences between A/B. Histological findings and p53 expression were comparable between groups before treatment (P > 0.1); microscopic analysis showed no differences between groups for most variables, after treatment. Slight but significant difference between A/B for p53 with major reduction post isotretinoin [0.66±0.31 vs. 0.94±0.34 respectively (P = 0.04) was observed. There were minor side effects and no significant laboratory test alterations. We concluded that no significant clinical, microscopic changes but p53 epidermal expression reduction were observed. The role of ultra-violet induced p53 mutation in skin carcinogenesis reinforces retinoids chemoprevention. Oral isotretinoin seemed safe but not effective to treat photoaging. Caution should be considered for women prone to pregnancy. Further controlled studies are necessary. © 2010 The International Society of Dermatology.

Effect of thickness of indirect restoration and distance from the light-curing unit tip on the hardness of a dual-cured resin cement

This study evaluated the Knoop hardness and polymerization depth of a dual-cured resin cement, light-activated at different distances through different thicknesses of composite resin. One bovine incisor was embedded in resin and its buccal surface was flattened. Dentin was covered with PVC film where a mold (0.8-mm-thick and 5 mm diameter) was filled with cement and covered with another PVC film. Light curing (40 s) was carried out through resin discs (2, 3, 4 or 5 mm) with a halogen light positioned 0, 1, 2 or 3 mm from the resin surface. After storage, specimens were sectioned for hardness measurements (top, center, and bottom). Data were subjected to split-plot ANOVA and Tukey's test (α=0.05). The increase in resin disc thickness decreased cement hardness. The increase in the distance of the light curing tip decreased hardness at the top region. Specimens showed the lowest hardness values at the bottom, and the highest at the center. Resin cement hardness was influenced by the thickness of the indirect restoration and by the distance between the light-curing unit tip and the resin cement surface.

Comparação entre as necessidades energéticas prescritas e administradas a pacientes em terapia nutricional enteral

Objective: evaluating the adequacy, prescription and energy supply of enteral nutrition therapy in hospitalized patients. Methods: was performed a retrospective survey of the evolution of TNE protocol of 59 patients hospitalized in a general hospital in Marília / SP / BR. Data collected included gender, age, clinical diagnosis, anthropometric and dietary data related to the prescribed dietary formula, route and method of administration of the enteral nutrition, the daily volume prescribed and administered, the daily amount of energy required and offered in the diet, as well as possible complications. Body mass index (BMI), triceps skinfold (TSF) and arm muscle circumference (AMC) were used to establish the nutritional status of the patients. The adequacy of ENT was done according to the daily energy requirement compared to the average energy received during the daily use of ENT. Results: The average found to the BMI was 21.4 kg/m 2, and no differences were found comparing male and female. The data for TSF and AMC were different between genders (p<0.05) and suggest a more severe muscle mass in relation to adipose tissue. The averaged to the energy requirements was 1642 kcal/day but the average of energy prescribed was 1045 kcal/day and the amount offered was 1035 kcal/day. There was a significant difference between the necessity and the supplied energy offered through enteral nutrition (p=0.00) as well between the energy required and prescribed (p =0.00), both were shorter than the necessity. There was no significant difference (p>0.05) in energy supply, volume of enteral nutrition prescribed and administered among eutrophic, underweight or overweight patients. Conclusion: The results of this study indicate that the prescription and energy supply were not based on the needs of these patients, causing a significant energy deficit, which can lead to worsening of the nutritional status of the same. In hospitalized patients in use of ENT, the energy requirement must be made by a qualified professional within the multidisciplinary team, based on the needs of each patient.

Microstructural characterization of layers produced by plasma nitriding on austenitic and superaustenitic stainless steel grades

High chromium content is responsible for the formation of a protective passive surface layer on austenitic stainless steels (ASS). Due to their larger amounts of chromium, superaustenitic stainless steels (SASS) can be chosen for applications with higher corrosion resistance requirements. However, both of them present low hardness and wear resistance that has limited their use for mechanical parts fabrication. Plasma nitriding is a very effective surface treatment for producing harder and wear resistant surface layers on these steel grades, without harming their corrosion resistance if low processing temperatures are employed. In this work UNS S31600 and UNS S31254 SASS samples were plasma nitrided in temperatures from 400 °C to 500 °C for 5 h with 80% H 2-20% N2 atmosphere at 600Pa. Nitrided layers were analyzed by optical (OM) and transmission electron microscopy (TEM), x-ray diffraction (XRD), and Vickers microhardness testing. Observations made by optical microscopy showed that N-rich layers were uniform but their thicknesses increased with higher nitriding temperatures. XRD analyses showed that lower temperature layers are mainly composed by expanded austenite, a metastable nitrogen supersaturated phase with excellent corrosion and tribological properties. Samples nitrided at 400 °C produced a 5 μm thick expanded austenite layer. The nitrided layer reached 25 lm in specimens treated at 500 °C. There are indications that other phases are formed during higher temperature nitriding but XRD analysis was not able to determine that phases are iron and/or chromium nitrides, which are responsible for increasing hardness from 850 up to 1100 HV. In fact, observations made by TEM have indicated that formation of fine nitrides, virtually not identified by XRD technique, can begin at lower temperatures and their growth is affected by both thermodynamical and kinetics reasons. Copyright © 2012 by ASTM International.

Importance of periodontal ligament thickness

This study evaluated whether periodontal ligament (PL) thickness varied with root size and examined the possible influence of this variation on orthodontic mechanics. Measurements were taken of the maxillary left first molar in 54 male Wistar rats. Mean mesial and distal PL thicknesses were compared between the intermediate buccal and mesiobuccal roots using paired Student's t-tests with a 5% significance level. Mean values differed significantly between roots (p < 2.2 × 10-16). PL thickness in rats is directly proportional to root dimensions.

Anthropometric changes in the brazilian cohort of older adults: SABE survey (Health, Well-Being, and Aging)

The aim of the present study was to analyze the anthropometric changes in a home-based cohort of Brazilian older adults who participated in the SABE Survey, conducted in 2000 and 2006. A total of 1030 men and women were examined by age group: 60-69, 70-79, and ≥80 years. This representative sample consists of the survivors of the 2000 cohort. The following anthropometric variables were assessed: body mass, arm muscle, waist and calf circumferences, triceps skinfold thickness, body mass index, waist-hip ratio, and arm muscle area according to mean values and percentile distribution. Except for body mass and body mass index, a significant difference (P<0.05) was observed among the assessed anthropometric variables during the follow-up period. The older adults ≥80 years presented the lowest values. The reduction in the mean values of triceps skinfold thickness was greater (30%) than that of waist circumference (9%) and was more pronounced in women (21%) than in men (9%). Arm muscle circumference and area reduced by 8% and 19%, respectively, in men and 1% and 3%, correspondingly, in women. Our findings revealed reductions in the mean values for all anthropometric variables in the follow-up period from 2000 to 2006 among older adults. © 2013 Manuela Ferreira de Almeida et al.

Gestantes vivendo com HIV/AIDS: Características antropométricas e peso ao nascer dos seus recém-nascidos

PURPOSE: To describe the anthropometric and pregnancy characteristics of women with HIV/AIDS, assisted by the Brazilian National Health System and the birth weight of their newborns. METHODS: The participants were women assisted at public STD/AIDS clinics of the Municipal Health system of São Paulo. The anthropometric characteristics were evaluated by trained nutritionists and other information was obtained from the medical records. For comparison of the survey data to those of the general population, secondary maternal and pregnancy data were obtained from live birth certificates through the Live Birth Information System. Continuous variables were summarized as mean and standard deviation or as the 25th, 50th and 75th percentiles and minimum and maximum values. The other variables are presented as percentages. Means were compared by the Student's t-test or Kruskal-Wallis test depending on the fulfillment of assumptions, with the decision based on the p value. RESULTS: We found the presence of inadequate maternal nutrition according to triceps skinfold (60.9%). The BMI/gestational age showed the presence of underweight (18.5%) and overweight or obesity (40%). There was no association between disease status (HIV or AIDS) and weight, height, and lean or fat mass. Mean newborn birth weight was lower than the value for the general population without infection or disease. The results of this study indicate the need to develop adapted curves to allow a more accurate nutritional assessment of this population group.