Carbon dioxide evaporation in a single microchannel

Despite its importance for designing evaporators and condensers, a review of the literature shows that heat transfer data during phase change of carbon dioxide is very limited, mainly for microchannel flows. In order to give a contribution on this subject, an experimental study of CO 2 evaporation inside a 0.8 mm-hydraulic diameter microchannel was performed in this work. The average heat transfer coefficient along the microchannel was measured and visualization of the flow patterns was conducted. A total of 67 tests were performed at saturation temperature of 23.3°C for a heat flux of 1800 W/(m2°C). Vapor qualities ranged from 0.005 to 0.88 and mass flux ranged from 58 to 235 kg/(m2s). An average heat transfer coefficient of 9700 W/(m2°C) with a standard deviation of 35% was obtained. Nucleate boiling was found to characterize the flow regime for the test conditions. The dryout of the flow, characterized by the sudden reduction in the heat transfer coefficient, was identified at vapor qualities around 0.85. Flow visualization results showed three flow patterns. For low vapor qualities (up to about 0.25), plug flow was predominant, while slug flow occurred at moderated vapor qualities (from about 0.25 to 0.50). Annular flow was the flow pattern for higher vapor qualities. Copyright © 2006 by ABCM.

Mitigating systematic errors for single frequency GPS receivers employing a penalized least squares methodology

Among the positioning systems that compose GNSS (Global Navigation Satellite System), GPS has the capability of providing low, medium and high precision positioning data. However, GPS observables may be subject to many different types of errors. These systematic errors can degrade the accuracy of the positioning provided by GPS. These errors are mainly related to GPS satellite orbits, multipath, and atmospheric effects. In order to mitigate these errors, a semiparametric model and the penalized least squares technique were employed in this study. This is similar to changing the stochastical model, in which error functions are incorporated and the results are similar to those in which the functional model is changed instead. Using this method, it was shown that ambiguities and the estimation of station coordinates were more reliable and accurate than when employing a conventional least squares methodology.

Design of a state observer using decay rate LMI constraints for fault detection in mechanical systems

Nowadays, one of the most important concerns for many companies is to maintain the operation of their systems without sudden equipment break down. Because of this, new techniques for fault detection and location in mechanical systems subject to dynamic loads have been developed. This paper studies of the influence of the decay rate in the design of state observers using LMI for fault detection in mechanical systems. This influence is analyzed by the performance index proposed by Huh and Stein for the condition of a state observer. An example is presented to illustrate the methodology discussed.

Photoelastic comparison of single tooth implant-abutment-bone of platform switching vs conventional implant designs

Objectives: The maintenance and stability of peri-implantar soft tissue seem to be related to the crestal bone around the implant platform and different implant designs connections might affect this phenomenon. The aim of this study was to evaluate by photoelastic analysis the stress distribution in the cervical and apical site of implant-abutment interface of conventional implant joints (external hex, internal hex and cone morse) and compare to the novel platform switching design. Materials and methods: It was fabricated photoelastic models using five different implant-abutment connection, one set of external hex (Alvim Ti, Neodent, Curitiba, Brazil), one set of internal hex (Full Osseotite, Biomet 3i, Florida, USA), one cone morse set (Alvim CM, Neodent, Curitiba, Brazil), and two sets of internal hex plus platform switching concept (Alvim II Plus, Neodent, Curitiba, Brazil) (Certain Prevail, Biomet 3i, Florida, USA). These models were submitted to two compressive loads, axial from 20 kgf (load I) and another (load II), inclined 45° from 10 kgf. During the qualitative analysis, digital pictures were taken from a polariscope, for each load situation. For the quantitative analyses in both situations of load, the medium, minimum and maximum in MPa values of shear strain were determined in the cervical and apical site. The Kruskal-Wallis test was used to compare the results between the different systems and between cervical and apical site were compared using Mann-Whitney U test. Results: The results from qualitative analysis showed less concentration of strain in the cervical area to the internal hex plus platform switching (Certain Prevail), in both situation of load. The same results were get in the quantitative analysis, showing less stress concentrations around the implant Certain Prevail with internal hex plus the novel design (17.9 MPa to load I and 29.5 MPa to load II), however, without statistical significant difference between the systems. Conclusion: The minor stress concentration strongly suggest the use of platform switching design as a manner to prevent bone loss around the implant-abutment platform. Clinical Significance: From the result of this study its possible to make clinical decision for implant system which provides implant components with platform switching characteristics.

Single-phase current-source-boost inverter for renewable energy sources

This paper presents a new methodology for the operation and control of a single-phase current-source (CS) Boost Inverter, considering that the conventional CS boost inverter has a right-half-plane (RHP) zero in its control-to-output transfer function, and this RHP zero causes the known non-minimum-phase effects. In this context, a special design with low boost inductance and a multi-loop control is developed in order to assure stable and very fast dynamics. Furthermore, the proposed inverter presents output voltage with very low total harmonic distortion (THD), reduced components and high power density. Therefore, this paper presents the inverter operation, the proposed control technique, the main simulation results and a prototype in order to demonstrate the feasibility of the proposal. © 2011 IEEE.

On a control design to an AFM microcantilever beam, operating in a tapping-mode, with irregular behavior

In last decades, control of nonlinear dynamic systems became an important and interesting problem studied by many authors, what results the appearance of lots of works about this subject in the scientific literature. In this paper, an Atomic Force Microscope micro cantilever operating in tapping mode was modeled, and its behavior was studied using bifurcation diagrams, phase portraits, time history, Poincare maps and Lyapunov exponents. Chaos was detected in an interval of time; those phenomena undermine the achievement of accurate images by the sample surface. In the mathematical model, periodic and chaotic motion was obtained by changing parameters. To control the chaotic behavior of the system were implemented two control techniques. The SDRE control (State Dependent Riccati Equation) and Time-delayed feedback control. Simulation results show the feasibility of the bothmethods, for chaos control of an AFM system. Copyright © 2011 by ASME.

Alignment of operations strategy: Exploring the marketing interface

Purpose - The purpose of this paper is to identify factors that can help managers to overcome barriers to alignment of operations strategy at the interface with marketing. Design/methodology/approach - This objective required the application of a procedure based on strategic consensus and a deeper analysis, such that the delimitation of the study in a single case was mandatory. The strategic processes of interfacing involve managerial attributes that are subject to the influence of human aspects and, therefore, the research method used a qualitative approach. The protocol design included the following data sources: interviews, document reviews and researcher observations. The categorisation was made based on the theoretical references, the frequency of observations, common responses and information from documents. Findings - The balance between intra-functional trade-offs, joint research on the competitive context, reflections on the understanding of customer needs and operational performance, and understanding of inter-functional trade-offs were the main factors verified. They effectively support decisions associated with interface processes and promotes the integration of these processes. They can generate inputs that enable managers to achieve an appropriate balance among alternatives in light of various trade-offs. Practical implications - These factors make possible new connections between strategic processes in the context of operations and marketing functions. The formations of these strategies are aligned through a better understanding of both threats and opportunities by means of a joint analysis of the competitive context. The presented findings can be used to develop a clear definition of strategic objectives of operations and a more appropriate treatment of market needs. Originality/value - The findings from the research can be considered as new elements for promoting alignment in the formation process of the operations strategy. Little research to date has examined the operations-marketing strategic interface of companies in the context of strategic consensus. © Emerald Group Publishing Limited.

Design of personal protective equipment: To promote of Brazilian artefacts with ergonomic attributes

This research aims to investigate a topic sometimes overlooked among the research of ergonomics. Particularly, we treat the garments as personal protective equipment. In this study we abode on clothing produced and used in Brazil, making notes about the management of occupational safety for the use of such equipment. In turn, identify Relevant requirements for the design of personal protective equipment used in Brazil, in line with what is being studied in global forums on the subject. © 2013 Taylor & Francis Group.

Televisão digital interativa: alternativa de design e usabilidade para o aplicativo som e prosa

Pós-graduação em Televisão Digital: Informação e Conhecimento - FAAC

Usabilidade de software: estudo de recomendações básicas para verificação do nível de conhecimento dos alunos dos cursos de Design Gráfico e Sistemas de Informação da UNESP/Bauru

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Contribuição da comunicação visual para o design de superfície

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Ferramentas de avaliação ergonômica em atividades multifuncionais: a contribuição da ergonomia para o design de ambientes de trabalho

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Diretrizes para análise e desenvolvimento de identidade visual: contribuições para o design ergonômico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modernization of Customs and Implementation of Single Window Systems for Foreign Trade: Results of an International Seminar-Workshop

An international seminar-workshop entitled "Facilitation of trade and transport in Latin America: situation and outlook" was held at the headquarters of the Economic Commission for Latin America and the Caribbean (ECLAC) on 29 and 30 November 2005, organized jointly by the ECLAC Division of International Trade and Integration and the United Nations Conference on Trade and Development (UNCTAD). The event was attended by about 50 persons involved in customs modernization and/or the implementation of single window systems for foreign trade in 20 Ibero-American countries.The main purpose of the seminar-workshop was to exchange ideas, opinions and proposals concerning the efficient implementation of trade facilitation instruments. The conclusions reached at this event point to the need to seek convergence among the existing trade agreements associated with trade facilitation in Latin America. Customs modernization requires the re-design of processes and procedures in order to achieve interoperability among the systems, and single window systems for foreign trade can only be implemented successfully if clear political leadership is established with broad participation from both public and private organizations.

Intervenção ergonômica e o uso da simulação computacional na concepção de produtos: o design de uma plantadora mecanizada de mandioca

Pós-graduação em Design - FAAC