Comportamento da cana-de-açúcar em duas safras e atributos físicos do solo, sob diferentes tipos de preparo

The tillage comprises on average 25% of the cost of deploying a reed, so this cost reduction measures are desirable since they do not compromise the quality of the operation and longevity of sugarcane. The objective was to evaluate the effect of different tillage systems in Acrustox, correlating soil physical properties and characteristics of sugarcane agroindustrial plant cane and ratoon cane. We used five types of soil tillage, over experimental design in blocks with five replications. The particle size was measured every 0.1 m to 0.4 m depth, through deformed soil samples collected at the end of the first growth cycle of the culture. For other soil physical properties: bulk density, total porosity and water content, assessments were performed at the end of each cycle, collecting soil samples in layers of 0-0.20 to 0.21-0.40 m, in addition to performing the penetration resistance, using a penetrometer impact. The response of sugarcane depending on the types of tillage was determined from the evaluation of productivity per hectare of stem (TCH), sugar (TPH), the values of pol % cane (AP), sugar total recoverable (ATR) and fiber samples collected at harvest stalk of sugarcane plant and ratoon cane. In the tillage studied, there was a change of the physical attributes of the soil, causing reduced productivity in 2009/2010 crop, compared with the 2008/2009 season. In tillage system of furrowing direct lowest result was observed for TCH, especially in 2009/2010 crop, when the difference with conventional tillage was 20.53 Mg ha(-1).

Efeito de reagentes de branqueamento na classificação e refinação de polpa de eucalipto

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aspectos da furação do titânio 6Al4V com broca de aço rápido sinterizado e broca de metal duro

Pós-graduação em Engenharia Mecânica - FEG

Caracterização de argilas usadas para produção de cerâmica vermelha e estudo das alterações nas suas propriedades pela adição de resíduos

Neste trabalho são apresentados os resultados de caracterização das principais argilas usadas pela indústria cerâmica vermelha regional e, também, de alguns resíduos sólidos produzidos na região de Presidente Prudente - SP. Os resultados da incorporação destes resíduos em massas cerâmicas são avaliados através do estudo de suas propriedades tecnológicas. Para a caracterização dos materiais foram utilizadas as seguintes técnicas: análise textural (concentração das frações areia, silte e argila), difratometria de raios X e análise térmica. As propriedades tecnológicas de corpos de prova cerâmicos foram avaliadas através dos seguintes parâmetros: retração linear (RL), perda de massa ao fogo (PF), massa específica aparente (MEA), porosidade aparente (PA), absorção de água (AA) e resistência mecânica à flexão (RMF). Corpos de prova, com diferentes concentrações de resíduos, foram prensados (prensa uniaxial manual) e queimados em temperaturas que variaram de 800 a 1200 oC, usando um forno tipo mufla com controle de temperatura. As argilas sedimentares foram coletadas nas margens do rio Paraná e em áreas de várzea, próximas as cerâmicas. As amostras estudadas, coletadas nos depósitos das cerâmicas, são usadas para produção de tijolos maciços, blocos furados e telhas. Quatro tipos diferentes de resíduos foram estudados: (1) lodo de estação de tratamento de água ETA, (2) torta de filtro de indústria de re-refino de óleo lubrificante, (3) pó de vidro (soda-cal) de garrafa tipo long neck descartável, e (4) cinza de bagaço de cana. Estes resíduos foram incorporados em massas cerâmicas coletadas nas indústrias... (Resumo completo, clicar acesso eletrônico abaixo)

Avaliação da influência dos parâmetros de processo de soldagem MIG no surgimento de poros em tubos de alumínio

The process of electric arc welding with shielding gas (GMAW) is being increasingly used in various industrial applications. This process occurs by which an electric arc is established between the work piece and a consumable in the form of wire, the arc melts the wire continuously as it is fed to the weld pool. The weld metal is protected from the atmosphere by flowing a gas (or gas mixture) inert or active. This paper presents a study of the welding process GMAW - MIG on aluminum tubes, alloy 6101 - T6, used in the manufacture of armored busbar, intended for driving electric power plants. 5(five) were welded specimens, changing certain welding parameters at each time was monitored welding joint as well as the interpass temperature. Tests were performed bending, tensile and macrographical analysis of body-of-evidence and through its results was possible to reach a better welding condition, which minimizes the appearance of pores, since the porosity has great influence on the mechanical strength and electrical conductivity of welded pipes

Obtenção e caracterização de suporte de regeneração óssea de dióxido de titânio

Due to complications caused by metallic implants in the replacement of bone tissue, the biological application of ceramics raised and became a viable alternative. The titania has the ability to promote bone tissue regeneration based on its structure, mechanical and biologically properties compatibility. The present work aims at obtaining and characterization of Titania (TiO2) porous ceramics produced by the polymeric sponge method (replica method). Polyurethane sponge with 10 ppi and 15 ppi (pores per linear inch) were used. The process differentiation is the air blower used to remove excess slurry. The ceramics sponges were dried in an oven, then pre-sintered at 1000 o C and sintered at 1450 o C. The effect of direct sintering at 1450 o C was also assessed. The percentage of solids used to prepare the slurry was 40 to 45% by weight. To increase the surface porosity of the sponge, 20% of starch was added. There was difficulty on controlling the thickness of the slurry layers on the sponge which resulted in the variation of samples mechanical resistance. Despite this, the results obtained are quite promising for the proposed use, indicating that it is possible to obtain titania sponges with an apparent porosity of around 60%, a bulk density ranging from 40 to 47% and a compressive strength resistance – that with better control of layers depositions – can vary from 1 to 4 MPa

O estudo da usinagem em torneamento da superliga à base de níquel Pyromet 31v

The search for materials with higher properties and characteristics (wear resistance, oxidation, corrosion, etc.) has driven research of various materials. Among the materials that are being studied with such properties and characteristics are super alloys based on nickel which has an important role in the aeronautical, automotive, marine, production of gas turbines and now in space vehicles, rocket engineering , experimental aircraft, nuclear reactors, steam-powered plants, petrochemical and many other applications because besides having all the characteristics and properties mentioned above also have an excellent performance at high temperatures. The super alloy based on nickel studied in this work is the super alloy Pyromet 31v normally used in the manufacture of exhaust valves in common engines and diesel engines of high power by cater requirements such as mechanical strength and corrosion resistance at temperatures of approximately 815 ° C. The objective of this work is to produce results to demonstrate more specific information about the real influence of coatings on cutting tools and cutting fluids in turning and thus promote the optimization of the machining of these alloys. The super alloy Pyromet 31v was processed through turning, being performed with various machining parameters such as cutting speed, feed rate, depth in conditions of Minimum Amount of Fluid (MAF), abundant fluid, cutting tools with coating and without coating in early in his work life and with wear. After turning were obtained several samples of chips and the part generated during the machining process, was measured roughness of the material, subsequently made macrostructural analysis of the tools used order to detect possible wear and microstructural analysis of samples collected being that the latter was used for Optical Microscopy, Scanning Electron Microscopy (SEM) and ... (Complete abstract click electronic access below)

Avaliação da qualidade de comprimidos de captopril 50 mg comercializados no Brasil

O captopril foi o primeiro agente desenvolvido para o tratamento da hipertensão, doença que acomete grande parte da população adulta mundial, a qual requer cuidados especiais quanto à farmacoterapia e ajuste de doses. Assim sendo, este trabalho tem como objetivo avaliar a qualidade de comprimidos de captopril 50 mg comercializados no Brasil através da realização da equivalência farmacêutica entre duas marcas de comprimidos não revestidos de captopril 50 mg (um genérico G e um similar S) em relação ao medicamento referência (R) Capoten® Bristol Myers Squibb 50 mg, utilizando os requisitos descritos na monografia individual do fármaco da Farmacopeia Brasileira e da Farmacopeia Americana. Medicamentos referência são produtos inovadores, cuja eficácia, segurança e qualidade foram comprovadas cientificamente; os chamados similares são os que contêm as mesmas substâncias ativas, mesma concentração, forma farmacêutica, via de administração, posologia e indicação terapêutica do medicamento de referência e são identificados por nome comercial ou por sua marca; os medicamentos genéricos são intercambiáveis com o produto referência e, geralmente, são produzido após a expiração ou renúncia da proteção patentária do mesmo, ele deve ser designado pela DCB (Denominação Comum Brasileira) ou, na ausência desta, pela DCI (Denominação Comum Internacional). Os dois medicamentos analisados, medicamento similar e medicamento genérico, apresentaram resultados satisfatórios quanto à determinação de peso médio, resistência mecânica e tempo de desintegração dos comprimidos, identificação, doseamento, limite de dissulfeto de captopril, uniformidade de doses unitárias, teste de dissolução e perfil de dissolução do fármaco, com relação ao seu medicamento referência correspondente, ou seja, estes são equivalentes farmacêuticos e apresentam qualidade... (Resumo completo, clicar acesso eletrônico abaixo)

Análise granulométrica do compósito cimentício produzido com adição de resíduos de madeira e escória

Since the early twenty-first century, the construction sector has been the second largest on the rise in the Brazilian industrial sector, with a growth of 1.4% in 2012, and is likely to remain at this level for a long time. However, unlike decades ago, the industry has been seeking in its manufacturing process, sustainable materials, encompassing in their works the concept of sustainability. Thus, the timber sector seeks to satisfy a market increasingly demanding, innovating techniques and utilization being less aggressive to the environment. The purpose of this study was to produce and evaluate the mechanical strength of the composite cement with the addition of wood residues and slag low oven. Therefore, it was made 42 specimen cement-slag-wood, carried out in two steps. Since at the first, it was varied only the slag particle size, and at the second, through the best result of the previous step, it was varied the wood particles granulometry. The mechanical performance of the composite was evaluated by the results obtained in the compression test and the physical test for determining the density of the material. In the first step of the process can be concluded that the best result was achieved with the use of slag particles retained on the 60 mesh sieve. In the second phase of the study concluded that the best results were achieved with wood particles with the large particles, i.e. particles retained on the 10 mesh sieve. Both in the first and in the second step it can be seen that there has been the influence of the particle size of the waste materials. With the obtained results, could be evaluated that the use of waste for the production of cement-slag-wood composite showed lower performance when compared to the results obtained in studies without the use of waste. However, some applications are feasible to be performed with the use of composite wood-cement-slag

Proposta para melhoria da qualidade dos produtos cerâmicos e de criação de um polo cerâmico artesanal na cidade de Indiana - SP

This work presents a proposal to create a Polo Ceramic Craft in the town of Indiana - SP, through the potter’s organization in a cooperative that will coordinate activities to add value to ceramic pieces. To achieve this, two things are essential: improving the ceramic body and improve the properties of the ceramic material. For the first action it’s necessary to create a Central Mass Production of Ceramics, to provide raw materials and homogeneous composition that results in differentiated ceramic after burning process (sintering). To this end, we propose the incorporation of additives (which act as fluxes) to the clay material. These additives can be mineral such as feldspar and nefelinas or leavings, such as glass powder obtained from disposable containers. For the second action is necessary to acquire an oven, electric or gas, it reaches higher temperatures (around 1200 ° C). The presence of the additive and burning at higher temperatures will enable better production of sintered ceramic material with less porosity and water absorption and higher mechanical strength, and pieces vitrified and glazed, allowing them to assign a higher value. For the production of these materials (thinner walls) requires a smaller volume of clayey raw materials. Besides benefiting the ceramic pieces, the proposed changes reduce the environmental impact caused by burning wood, since it will be replaced by natural gas (or electricity), and even will reduce the disposal of glass containers in the environment by recycling and incorporating this material in the clay. From a social standpoint, the cooperative is crucial to the viability of the proposed project, to coordinate activities and commercial production, which will result in better wages and profits for companies and consequently for the city and its population

Análise do teor de compostos fenólicos e de ligninas em diferentes órgãos vegetativos de espécies arbóreas nativas de diferentes grupos sucessionais

O sucesso do desenvolvimento da dinâmica das formações vegetais depende das relações estabelecidas entre as espécies vegetais com outros organismos e com o meio físico. Tais relações estão sujeitas a situações de estresse, podendo esse ser de caráter abiótico, como condições elevadas de radiação solar e temperatura e déficit hídrico ou de caráter biótico, como a herbivoria e o ataque de patógenos. Dessa maneira, em virtude à necessidade de um sistema de defesa, as plantas utilizam compostos químicos, como compostos fenólicos e ligninas, para se desenvolverem com proteção. Os compostos fenólicos são compostos oriundos do metabolismo secundário vegetal e ocorrem na parede celular dos tecidos vegetais, constituindo assim uma rápida linha de defesa vegetal a lesões e infecções e funcionando como substrato para atuação de enzimas de defesa como peroxidases e polifenoloxidases. Junto com a atuação dos compostos fenólicos, as ligninas fornecem à planta maior resistência mecânica e impermeabilidade suficiente aos vasos condutores do xilema, proporcionando, assim, desde um fundamental auxílio aos vegetais na conquista do ambiente terrestre até o estabelecimento de uma barreira protetora eficiente contra o ataque de microorganismos. Assim, por meio da extração e análise dos teores de compostos fenólicos e de ligninas de porção de raiz, caule, ápice caulinar e folhas maduras e imaturas de indivíduos de Erythrina speciosa Andrews, Eugenia uniflora L., Hevea brasiliensis M. Arg., Hymenaea courbaril L. var. stilbocarpa (Hayne) Lee et Lang, Joannesia princeps Vell., Lecythis pisonis Cambess, Licania tomentosa (Benth.) Fritsch, Pachira aquatica Aubl. e Psidium guajava L., classificou-se como espécies pioneiras Erythrina speciosa Andrews, Hymenaea courbaril L. var. stilbocarpa (Hayne) Lee et Lang, Joannesia princeps Vell., Pachira aquatica Aubl... (Resumo completo, clicar acesso eletrônico abaixo)

Vitrocerâmicas para blindagens balísticas

The use of ceramic materials in ballistic armor is considerable. Such materials can be very harder and lighter than metallic materials commonly used and it presents advantages to replace metallic materials when necessary toughness can be achieved. However, as SiC and Al2O3 ceramic, traditionally used for shielding, still have high manufacturing cost or low density do not have enough to shield applications such as aircraft. An alternative is the glass-ceramics, ceramics obtained by controlled crystallization of glasses, whose properties can be adjusted by choosing the chemical composition of glass, heat treatment of crystallization and special treatments such as ion exchange on the surface, resulting in increased mechanical strength . The objective of this project is to study the kinetics of crystallization of a glass composition based on cordierite (2MgO.2Al2O3.5SiO2), low density and high hardness, for the manufacture of glass-ceramics for ballistic tests. Shown in this report are results of heat treatment of crystallization and characterization by thermal analysis (DSC) glass obtained previously, indicating uneven distribution of crystals, and drying, weighing, mixing of raw materials and a new fusion of glass, the same composition

Otimização do braço inferior da suspensão dianteira do veículo Baja utilizando o método dos elementos finitos

Mass reduction coupled with the mechanical performance in service has been the goal of many projects related to the transport area, considering the advantages that mass reduction can bring. However, make a simple material substitution without design a new geometry to corroborate for the best component performance, often makes the replacement unviable. In this study, it was investigated the advantages of replacing the prototype BAJA SAE front suspension lower arm of Equipe Piratas do Vale de BAJA SAE - Universidade Paulista, Campus Guaratinguetá, actually produced with steel, for a new component made of carbon fiber composite. The new geometry has been developed to provide the best possible performance for this component and your easy manufacturing. The study was done using the 3D modeling tools and computer simulations via finite element method. The first stage of this work consisted on calculation of the estimated maximum contact force tire / soil in a prototype landing after jump at one meter high, drop test in the laboratory with the current vehicle, current front suspension lower arm 3D modeling, finite element simulation and analysis of critical regions. After all current component analysis, a new geometry for the part in study was designed and simulated in order to reduce the component mass and provide a technological innovation using composite materials. With this work it was possible to obtain a theoretical component mass reduction of 25,15% maintaining the mechanical strength necessary for the appropriated component performance when incited

Implementação de um tuboexpansor na refinaria do Planalto Paulista – REPLAN com objetivo do aproveitamento da energia contida nos gases residuais do FCC – Fluid Catalytic Cracking na geração de energia elétrica

The steel type AISI 4130 (ultra-high strength steel) is an alloy of low carbon and its main alloying elements are chromium and molybdenum, which improves the toughness of the weld metal. It has numerous applications, especially where the need for high mechanical strength. It is widely used in equipment used by the aviation industry, such as cradle-tomotor, and this is the motivation for this study. Cots are of fundamental importance, because the engine supports and maintains balance in the fixed landing gear. This equipment is subjected to intense loading cycles, whose fractures caused by fatigue are constantly observed. Will be determined the effects caused by re-welding the structure of aeronautical equipment, and will also study the microstructure of the metal without welding. The studies will be done on materials used in aircraft, which was given to study. The results provide knowledge of microstructure to evaluate any type of fracture that maybe caused by fatigue. Fatigue is a major cause of aircraft accidents and incidents occurred, which makes the study of the microstructure of the metal, weld and re-solder the knowledge essential to the life of the material. The prevention and control of the process of fatigue in aircraft are critical, since the components are subjected to greater responsibility cyclic loading

Alterações microestruturais decorrentes dos sucessivos reparos de solda TIG aplicados ao longo da vida útil de uma estrutura aeronáutica crítica à segurança de vôo

The steel type AISI 4130 (ultra-high strength steel) is an alloy of low carbon and its main alloying elements are chromium and molybdenum, which improves the toughness of the weld metal. It has numerous applications, especially where the need for high mechanical strength. It is widely used in equipment used by the aviation industry, such as cradle-tomotor, and this is the motivation for this study. Cots are of fundamental importance, because the engine supports and maintains balance in the fixed landing gear. This equipment is subjected to intense loading cycles, whose fractures caused by fatigue are constantly observed. Will be determined the effects caused by re-welding the structure of aeronautical equipment, and will also study the microstructure of the metal without welding. The studies will be done on materials used in aircraft, which was given to study. The results provide knowledge of microstructure to evaluate any type of fracture that maybe caused by fatigue. Fatigue is a major cause of aircraft accidents and incidents occurred, which makes the study of the microstructure of the metal, weld and re-solder the knowledge essential to the life of the material. The prevention and control of the process of fatigue in aircraft are critical, since the components are subjected to greater responsibility cyclic loading