Red-Green-Blue 2D tuneable liquid crystal laser devices

In this paper, we review our recent experimental work on coherent and blue phase liquid crystal lasers.We will present results on thin-film photonic band edge lasing devices using dye-doped low molar mass liquid crystals in self-organised chiral nematic and blue phases. We show that high Q-factor lasers can be achieved in these materials and demonstrate that a single mode output with a very narrow line width can be readily achievable in well-aligned mono-domain samples. Further, we have found that the performance of the laser, i.e. the slope efficiency and the excitation threshold, are dependent upon the physical parameters of the low molar mass chiral nematic liquid crystals. Specifically, slope efficiencies greater than 60% could be achieved depending upon the materials used and the device geometry employed. We will discuss the important parameters of the liquid crystal host/dye guest materials and device configuration that are needed to achieve such high slope efficiencies. Further we demonstrate how the wavelength of the laser can be tuned using an in-plane electric field in a direction perpendicular to the helix axis via a flexoelectric mechanism as well as thermally using thermochromic effects. We will then briefly outline data on room temperature blue phase lasers and further show how liquid crystal/lenslet arrays have been used to demonstrate 2D laser emission of any desired wavelength. Finally, we present preliminary data on LED/incoherent pumping of RG liquid crystal lasers leading to a continuous wave output. © 2009 SPIE.

Printed red-green-blue liquid crystal lasers

We present printable laser devices formed by dispersing dye-doped chiral nematic liquid crystals in solution-processible polymers. Unlike current technology, this allows lasers to be formed on a wide variety of surfaces, e.g. paper, plastic, metal. © 2012 OSA.

Enhanced infra-red emission from sub-millimeter microelectromechanical systems micro hotplates via inkjet deposited carbon nanoparticles and fullerenes

In this paper, we demonstrate a micro-inkjet printing technique as a reproducible post-process for the deposition of carbon nanoparticles and fullerene adlayers onto fully CMOS compatible micro-electro-mechanical silicon-on-insulator infrared (IR) light sources to enhance their infrared emission. We show experimentally a significant increase in the infrared emission efficiency of the coated emitters. We numerically validate these findings with models suggesting a dominant performance increase for wavelengths <5.5 μm. Here, the bimodal size distribution in the diameter of the carbon nanoparticles, relative to the fullerenes, is an effective mediator towards topologically enhanced emittance of our miniaturised emitters. A 90% improvement in IR emission power density has been shown which we have rationalised with an increase in the mean thickness of the deposited carbon nanoparticle adlayer. © 2013 AIP Publishing LLC.

Printed red-green-blue liquid crystal lasers

We present printable laser devices formed by dispersing dye-doped chiral nematic liquid crystals in solution-processible polymers. Unlike current technology, this allows lasers to be formed on a wide variety of surfaces, e.g. paper, plastic, metal. © OSA 2012.

Characterization of the porcine differentially expressed PDK4 gene and association with meat quality

To investigate the differential expression of genes in the skeletal muscle between Yorkshire and Chinese indigenous breed Meishan pigs, suppression subtractive hybridization was carried out and many genes were proved to be expressed significantly different in the two breeds. One gene highly expressed in Meishan but lowly expressed in Yorkshire specific library, shared strong homology with human pyruvate dehydrogenase kinase 4 (PDK4). Using semi-quantity and quantity PCR, We confirmed its differential expression between the two breeds. Temporal and spatial expression analysis indicated that porcine PDK4 gene is highly expressed in skeletal muscle and the highest in neonatal pigs. Complete cDNA cloning and sequence analysis revealed that porcine PDK4 gene contains an open reading frame of 1,221 bp. The deduced amino acid sequence showed conservation in evolution. A G/A mutation in intron 9 was identified and association analysis showed that it was significantly associated with intramuscular fat, muscle water content.

Expression pattern, cellular localization and promoter activity analysis of ovarian aromatase (Cyp19a1a) in protogynous hermaphrodite red-spotted grouper

Aromatase plays a key role in sex differentiation of gonads. In this study, we cloned the full-length cDNA of ovarian aromatase from protogynous hermaphrodite red-spotted grouper (Epinephelus akaara), and prepared the corresponding anti-EaCyp19a1a antiserum. Western blot and immunofluorescence studies revealed ovary-specific expression pattern of EaCyp19a1a in adults and its dynamic expression change during artificial sex reversal. EaCyp19a1a was expressed by follicular cells of follicular layer around oocytes because strong EaCyp19a1a immunofluorescence was observed in the cells of ovaries. During artificial sex reversal, EaCyp19a1a expression dropped significantly from female to male, and almost no any positive EaCyp19a1a signal was observed in testicular tissues. Then, we cloned and sequenced a total of 1967 bp T-flanking sequence of EaCyp19a1a promoter, and showed a number of potential binding sites for some transcriptional factors, such as SOX5, GATA gene family, CREB, AP1, FOXL1, C/EBP, ARE and SF-1. Moreover, we prepared a series of 5' deletion promoter constructs and performed in vitro luciferase assays of EaCyp19a1a promoter activities. The data indicated that the CREB regulation region from -1010 to -898 might be a major cis-acting element to EaCyp19a1a promoter, whereas the elements GATA and SOX5 in the region from -1216 to -1010 might be suppression elements. Significantly, we found a common conserved sequence region in the fish ovary-type aromatase promoters with identities from 93% to 34%. And, the motifs of TATA box, SF-1, SOX5, and CREB existed in the region and were conserved among the most of fish species. (C) 2009 Elsevier Ireland Ltd. All rights reserved.

A high throughput Nile red method for quantitative measurement of neutral lipids in microalgae

Isolation of high neutral lipid-containing microalgae is key to the commercial success of microalgae-based biofuel production. The Nile red fluorescence method has been successfully applied to the determination of lipids in certain microalgae, but has been unsuccessful in many others, particularly those with thick, rigid cell walls that prevent the penetration of the fluorescence dye. The conventional "one sample at a time" method was also time-consuming. In this study, the solvent dimethyl sulfoxide (DMSO) was introduced to microalgal samples as the stain carrier at an elevated temperature. The cellular neutral lipids were determined and quantified using a 96-well plate on a fluorescence spectrophotometer with an excitation wavelength of 530 nm and an emission wavelength of 575 run. An optimized procedure yielded a high correlation coefficient (R-2 = 0.998) with the lipid standard triolein and repeated measurements of replicates. Application of the improved method to several green algal strains gave very reproducible results with relative standard errors of 8.5%, 3.9% and 8.6%, 4.5% for repeatability and reproducibility at two concentration levels (2.0 mu g/mL and 20 mu g/mL), respectively. Moreover, the detection and quantification limits of the improved Nile red staining method were 0.8 mu g/mL and 2.0 mu g/mL for the neutral lipid standard triolein, respectively. The modified method and a conventional gravimetric determination method provided similar results on replicate samples. The 96-well plate-based Nile red method can be used as a high throughput technique for rapid screening of a broader spectrum of naturally-occurring and genetically-modified algal strains and mutants for high neutral lipid/oil production. (C) 2009 Published by Elsevier B.V.