Reduction of Torque Ripple in Induction Motor Drives Using an AdvancedHybrid PWM Technique

A voltage source inverter-fed induction motor produces a pulsating torque due to application of nonsinusoidal voltages. Torque pulsation is strongly influenced by the pulsewidth modulation (PWM) method employed. Conventional space vector PWM (CSVPWM) is known to result in less torque ripple than sine-triangle PWM. This paper aims at further reduction in the pulsating torque by employing advanced bus-clamping switching sequences, which apply an active vector twice in a subcycle. This paper proposes a hybrid PWM technique which employs such advanced bus-clamping sequences in conjunction with a conventional switching sequence. The proposed hybrid PWM technique is shown to reduce the torque ripple considerably over CSVPWM along with a marginal reduction in current ripple.

Finnish cattle as reservoir of Campylobacter spp.

The reported incidence of human campylobacteriosis in Finland is higher than in most other European countries. A high annual percentage of sporadic infections is of foreign origin, although a notable proportion of summer infections is domestically acquired. While chickens appear to be a major source of campylobacters for humans in most countries, the prevalence of campylobacters is very low in chicken slaughter batches in Finland. Data on other potential animal reservoirs of human pathogenic campylobacters in Finland are scarce. Consequently, this study aimed to investigate the status of Finnish cattle as a potential source of thermophilic Campylobacter spp. and antibiotic-resistant Campylobacter jejuni for human sporadic campylobacter infections of domestic origin. A survey of the prevalence of thermophilic Campylobacter spp. in Finnish cattle studied bovine rectal faecal samples (n=952) and carcass surface samples (n=948) from twelve Finnish slaughterhouses from January to December 2003. The total prevalence of Campylobacter spp. in faecal samples was 31.1%, and in carcass samples 3.5%. Campylobacter jejuni, the most common species, was present in 19.5% of faecal samples and in 3.1% of carcasses. In addition to thermophilic Campylobacter spp., C. hyointestinalis ssp. hyointestinalis was present in bovine samples. The prevalence of campylobacters was higher among beef cattle than among dairy cattle. Using the enrichment method, the number of positive faecal samples was 7.5 times higher than that obtained by direct plating. The predominant serotypes of faecal C. jejuni, determined by serotyping with a set of 25 commercial antisera for heat-stable antigens (Penner), were Pen2 and Pen4-complex, which covered 52% of the samples. Genotyping with pulsed-field gel electrophoresis (PFGE) using SmaI restriction yielded a high diversity of C. jejuni subtypes in cattle. Determining the minimum inhibitory concentrations of ampicillin, enrofloxacin, erythromycin, gentamicin, nalidixic acid, and oxytetracycline among bovine C. jejuni isolates using a commercial broth microdilution method yielded 9% of isolates resistant to at least one of the antimicrobials examined. No multiresistant isolates were found among the bovine C. jejuni strains. The study of the shedding patterns of Campylobacter spp. among three Finnish dairy cattle herds included the examination of fresh faecal samples and tank milk samples taken five times, as well as samples from drinking troughs taken once during the one-year study. The semiquantitative enrichment method detected C. jejuni in 169 of the 340 faecal samples, mostly at low levels. In addition, C. jejuni was present in one drinking trough sample. The prevalence between herds and sampling occasions varied widely. PFGE, using SmaI as restriction enzyme, identified only a few subtypes in each herd. In two 2 of the herds, two subtypes persisted throughout the sampling. Individual animals presented various shedding patterns during the study. Comparison of C. jejuni isolates from humans, chickens and cattle included the design of primers for four new genetic markers selected from completely sequenced C. jejuni genomes 81-176, RM1221 and NCTC 11168, and the PCR examination of domestic human isolates from southern Finland in 1996, 2002 and 2003 (n=309), chicken isolates from 2003, 2006 and 2007 (n=205), and bovine isolates from 2003 (n=131). The results revealed that bovine isolates differed significantly from human and chicken isolates. In particular, the - glutamyl transpeptidase gene was uncommon among bovine isolates. The PFGE genotyping of C. jejuni isolates, using SmaI and KpnI restriction enzymes, included a geographically representative collection of isolates from domestic sporadic human infections, chicken slaughter batches, and cattle faeces and carcasses during the seasonal peak of campylobacteriosis in the summer of 2003. The study determined that 55.4% of human isolates were indistinguishable from those of chickens and cattle. Temporal association between isolates from humans and chickens was possible in 31.4% of human infections. Approximately 19% of the human infections may have been associated with cattle. However, isolates from bovine carcasses and human cases represented different PFGE subtypes. In conclusion, this study suggests that Finnish cattle is a notable reservoir of C. jejuni, the most important Campylobacter sp. in human enteric infections. Although the concentration of these organisms in bovine faeces appeared to be low, excretion can be persistent. The genetic diversity and presence or absence of marker genes support previous suggestions of host-adapted C. jejuni strains, and may indicate variations in virulence between strains from different hosts. In addition to chickens, Finnish cattle appeared to be an important reservoir and possible source of C. jejuni in domestic sporadic human infections. However, sources of campylobacters may differ between rural and urban areas in Finland, and in general, the transmission of C. jejuni of bovine origin probably occurs via other routes than food.

Lightning-Induced Current and Voltage on a Rocket in the Presence of Its Trailing Exhaust Plume

This paper presents time-domain characteristics of induced current and voltage on a rocket in the presence of its exhaust plume when an electromagnetic (EM) wave generated by a nearby lightning discharge is incident on it. For the EM-field interaction with the rocket, the finite-difference time-domain technique has been used. The distributed electrical parameters, such as capacitance and inductance of the rocket and its exhaust plume, are computed using the method of moments technique. For the electrical characterization of the exhaust plume, the computational fluid dynamics technique has been used. The computed peak value of the electrical conductivity of the exhaust plume is 0.12 S/m near the exit plane and it reduces to 0.02 S/m at the downstream end. The relative permittivity varies from 0.91 to 0.99. The exhaust plume behaves as a good conductor for EM fields with frequencies less than 2.285 GHz. It has been observed that the peak value of the induced current on the rocket gets enhanced significantly in the presence of the conducting exhaust plume for the rocket and exhaust plume dimensions and parameters studied. The magnitude of the time-varying induced current at the tail is much more than that of any other section of the rocket.

Lightning-Induced Current and Voltage on a Rocket in the Presence of Its Trailing Exhaust Plume

This paper presents time-domain characteristics of induced current and voltage on a rocket in the presence of its exhaust plume when an electromagnetic (EM) wave generated by a nearby lightning discharge is incident on it. For the EM-field interaction with the rocket, the finite-difference time-domain technique has been used. The distributed electrical parameters, such as capacitance and inductance of the rocket and its exhaust plume, are computed using the method of moments technique. For the electrical characterization of the exhaust plume, the computational fluid dynamics technique has been used. The computed peak value of the electrical conductivity of the exhaust plume is 0.12 S/m near the exit plane and it reduces to 0.02 S/m at the downstream end. The relative permittivity varies from 0.91 to 0.99. The exhaust plume behaves as a good conductor for EM fields with frequencies less than 2.285 GHz. It has been observed that the peak value of the induced current on the rocket gets enhanced significantly in the presence of the conducting exhaust plume for the rocket and exhaust plume dimensions and parameters studied. The magnitude of the time-varying induced current at the tail is much more than that of any other section of the rocket.

Vapour phase synthesis of salol over solid acids via transesterification

The transesterification of methyl salicylate with phenol has been studied in vapour phase over solid acid catalysts such as ZrO2, MoO3 and SO42- or Mo(VI) ions modified zirconia. The catalytic materials were prepared and characterized for their total surface acidity, BET surface area and powder XRD patterns. The effect of mole-ratio of the reactants, catalyst bed temperature, catalyst weight, flow-rate of reactants, WHSV and time-on-stream on the conversion (%) of phenol and selectivity (%) of salol has been investigated. A good yield (up to 70%) of salol with 90% selectivity was observed when the reactions were carried out at a catalyst bed temperature of 200 degrees C and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst. The results have been interpreted based on the variation of acidic properties and powder XRD phases of zirconia on incorporation of SO42- or Mo(VI) ions. The effect of poisoning of acid sites of SO42- or Mo(VI) ions modified zirconia on total surface acidity, powder XRD phases and catalytic activity was also studied. Possible reaction mechanisms for the formation of salol and diphenyl ether over acid sites are proposed.

New Solid State Forms of the Anti-HIV Drug Efavirenz. Conformational Flexibility and High Z ` Issues

Structural information on the solid forms of efavirenz, a non-nucleoside reverse transcriptase inhibitor, is limited, although various polymorphic forms of this drug have been patented. We report here structural studies of four new crystal forms a pure form, a cyclohexane solvate, and cocrystals with 1,4-cyclohexanedione and 4,4'-bipyridine. Temperature dependent single-crystal to single-crystal phase transitions are observed for the pure form and for the cyclohexane solvate with an increase in the number of symmetry independent molecules, Z', upon a lowering of temperature. Other issues related to these solid forms, such as thermal stability, conformational flexibility, and high Z' occurrences, are addressed by using a combined experimental and computational approach.

NMR relaxation study of disorder in condensed matter: solid solutions of betaine phosphate and phosphite

Proton NMR relaxation measurements have been carried out in anti-ferroelectric Betaine phosphate (BP), ferroelectric Betaine phosphite (BPI) and the mixed system BPI(1-x)BPx, at 11.4MHz and 23.3MHz from 300K to 80K for x=0.0, 0.25, 0.45, 0.85, and 1.0. The temperature dependence of spin lattice relaxation time T, exhibits two minima as expected from the BPP model in BP and BPI. The Larmor frequency dependence of T, in the mixed system is rather unusual and exhibits different slopes for the low temperature wings at the two frequencies, which is a clear experimental evidence of the presence of different methyl groups with different activation energies (E-a) indicating disorder.

Robust prediction of residual velocities and ballistic limits of projectiles for impact on thin aluminium plates

This paper deals with the simulation-driven study of the impact of hardened steel projectiles on thin aluminium target plates using explicit finite element analysis as implemented in LS-DYNA. The evaluation of finite element modelling includes a comprehensive mesh convergence study using shell elements for representing target plates and the solid element-based representation of ogivalnosed projectiles. A user-friendly automatic contact detection algorithm is used for capturing interaction between the projectile and the target plate. It is shown that the proper choice of mesh density and strain rate-dependent material properties is crucial as these parameters significantly affect the computed residual velocity. The efficacy of correlation with experimental data is adjudged in terms of a 'correlation index' defined in the present study for which values close to unity are desirable.By simulating laboratory impact tests on thin aluminium plates carried out by earlier investigators, extremely good prediction of experimental ballistic limits has been observed with correlation indices approaching unity. Additional simulation-based parametric studies have been carried out and results consistent with test data have been obtained. The simulation procedures followed in the present study can be applied with confidence in designing thin aluminium armour plates for protection against low calibre projectiles.

Rare earth exchanged (Ce3+, La3+ and RE3+) H-Y zeolites as solid acid catalysts for the synthesis of linear alkyl benzenes

Rare earth exchanged H–Y zeolites were prepared by simple ion exchange methods at 353 K and have been characterized using different physicochemical techniques. A strong peak around 58 ppm in the 27Al{1H} MAS NMR spectra of these zeolites suggests a tetrahedral coordination for the framework aluminium. Small peak at or near 0 ppm is due to hexa-coordinated extra-framework aluminium and a shoulder peak near 30 ppm is a penta-coordinated aluminium species; [Al(OH)4]−. The vapor-phase benzene alkylation with 1-decene and 1-dodecene was investigated with these catalytic systems. Under the reaction conditions of 448 K, benzene/olefin molar ratio of 20 and time on stream 3 h, the most efficient catalyst was CeH–Y which showed more than 70% of olefin conversion with 48.5% 2-phenyldecane and 46.8%, 2-phenyldodecane selectivities with 1-decene and 1-dodecene respectively.

Soft condensed matter -A special issue of solid state communications -Foreword

It is a policy of Solid State Communications’ Executive Editorial Board to organize special issues from time to time on topics of current interests. The present issue focuses on soft condensed matter, a rapidly developing and diverse area of importance not only for the basic science, but also for its potential applications. The ten articles in this issue are intended to give the readers a snapshot of some latest developments in soft condensed matter, mainly from the point of view of basic science. As the special issues are intended for a broad audience, most articles are short reviews that introduce the readers to the relevant topics. Hence this special issue can be especially helpful to readers who might not be specialists in this area but would like to have a quick grasp on some of the interesting research directions.

Studies on the ageing behaviour of Polyvinylchloride/ammonium perchlorate composite solid propellant

The effects of ageing on the properties of a complete polyvinyl chloride — dibutyl phthalate — ammonium perchlorate solid propellant have been studied by measurements of burning rates, thermal decomposition rates (by thermogravimetry and DTA) and calorimetric values. Ageing leads to loss of HCl by dehydrochlorination and a corresponding increase in heat of combustion.

Nonlinear intrinsic instability of solid propellant combustion including gas-phase thermal inertia

The problem of homogeneous solid propellant combustion instability is studied with a one-dimensional flame model, including the effects of gas-phase thermal inertia and nonlinearity. Computational results presented in this paper show nonlinear instabilities inherent in the equations, due to which periodic burning is found even under steady ambient conditions such as pressure. The stability boundary is obtained in terms of Denison-Baum parameters. It is found that inclusion of gas-phase thermal inertia stabilizes the combustion. Also, the effect of a distributed heat release in the gas phase, compared to the flame sheet model, is to destabilize the burning. Direct calculations for finite amplitude pressure disturbances show that two distinct resonant modes exist, the first one near the natural frequency as obtained from intrinsic instability analysis and a second mode occurring at a much higher driving frequency. It is found that er rn in the low frequency region, the response of the propellant is significantly affected by the specific type of gas-phase chemical heat-release model employed. Examination of frequency response function reveals that the role of gas-phase thermal inertia is to stabilize the burning near the first resonant mode. Calculations made for different amplitudes of driving pressure show that the mean burning rate decreases with increasing amplitude. Also, with an increase in the driving amplitude, higher harmonics are generated in the burning rate.