Amplificador de envolvente de señales de RF basado en el convertidor buck multifase

En este trabajo se presenta un convertidor DC-DC buck de dos fases de alta velocidad adecuado para emplear en técnicas de linealización de amplificadores como ET (Envelope Tracking) o EER (Envelope Elimination and Restoration). El convertidor ha sido realizado con tecnología LDMOS y la técnica usada para controlarlo ha sido modulación PWM, creada mediante procesado digital y un generador de funciones. La potencia de salida es de hasta 125W de pico, con un rendimiento del 80%, un ancho de banda de hasta 2MHz y en las medidas de linealidad presenta una atenuación a los productos de intermodulación de tercer orden de más de 45 dBc.

Procedimiento De Amplificador De Envolvente De Señales Moduladas En RF Para Técnicas EER Y ET

An envelope amplifier for an EER (Envelope Elimination and Restoration) and ET (Envelope Tracking) techniques is shown in this paper. The amplifier is based on a high speed two phases buck converter and employs RF LDMOS technology for the switching stage. A DPWM (Digital Pulse With Modulation) signal is used to control the amplifier by means of a functions generator. Simulations and measurements on a circuit prototype are presented showing a good agreement. Up to 125W output peak power can be delivered over a 5Ω load resistor. About 80% efficiency has been obtained. And at the two tone test, the third order intermodulation products (IP3) remain below 45dBc over a 2MHz bandwidth.

Monitoring maximum peak power density values as a more reliable marker for measurement procedures to elucidate RF EMF health effects: Leganes project

Considering the measurement procedures recommended by the ICNIRP, this communication is a proposal for a measurement procedure based in the maximum peak values of equivalent plane wave power density. This procedure has been included in a project being developed in Leganés, Spain. The project plans to deploy a real time monitoring system for RF to provide the city with a useful tool to adapt the environmental EM conditions to the new regulations approved. A first stage consisting of 105 measurement points has been finished and all the values are under the threshold of the regulation.

Design methodology in multiphase buck converter based on minimum time control for high efficiency RF amplifiers

This paper proposes an interleaved multiphase buck converter with minimum time control strategy for envelope amplifiers in high efficiency RF power amplifiers. The solution of the envelope amplifier is to combine the proposed converter with a linear regulator in series. High system efficiency can be obtained through modulating the supply voltage of the envelope amplifier with the fast output voltage variation of the converter working with several particular duty cycles that achieve total ripple cancellation. The transient model for minimum time control is explained, and the calculation of transient times that are pre-calculated and inserted into a look-up table is presented. The filter design trade-off that limits capability of envelope modulation is also discussed. The experimental results verify the fast voltage transient obtained with a 4-phase buck prototype.

Design of envelope amplifier based on interleaved multiphase buck converter with minimum time control for RF application

In this paper, an interleaved multiphase buck converter with minimum time control strategy for envelope amplifiers in high efficiency RF power amplifiers is proposed. The solution for the envelope amplifier is to combine the proposed converter with a linear regulator in series. High efficiency of envelope amplifier can be obtained through modulating the supply voltage of the linear regulator. Instead of tracking the envelope, the buck converter has discrete output voltage that corresponding to particular duty cycles which achieve total ripple cancellation. The transient model for minimum time control is explained, and the calculation of transient times that are pre-calculated and inserted into a lookup table is presented. The filter design trade-off that limits capability of envelope modulation is also discussed. The experimental results verify the fast voltage transient obtained with a 4-phase buck prototype.

Multiphase Buck Converter with Minimum Time Control Strategy for RF Envelope Modulation

Power amplifier supplied with constant supply voltage has very low efficiency in the transmitter. A DC-DC converter in series with a linear regulator can be used to obtain voltage modulation. Since this converter should be able to change the output voltage very fast, a multiphase buck converter with a minimum time control strategy is proposed. To modulate supply voltage of the envelope amplifier, the multiphase converter works with some particular duty cycle (i/n, i=1, 2 ... n, n is the number of phase) to generate discrete output voltages, and in these duty cycles the output current ripple can be completely cancelled. The transition times for the minimum time are pre-calculated and inserted in a look-up table. The theoretical background, the system model that is necessary in order to calculate the transition times and the experimental results obtained with a 4-phase buck prototype are given

Optimum Design of an Envelope Tracking Buck Converter for RF PA using GaN HEMTs

In this paper, filter design methodology and application of GaN HEMTs for high efficiency Envelope Amplifier in RF transmitters are proposed. The main objectives of the filter design are generation of the envelope reference with the minimum possible distortion and high efficiency of the amplifier obtained by the optimum trade-off between conduction and switching losses. This optimum point was determined using power losses model for synchronous buck with sinusoidal output voltage and experimental results showed good correspondence with the model and verified the proposed methodology. On the other hand, comparing to Si MOSFETs, GaN HEMTs can provide higher efficiency of the envelope amplifier, due to superior conductivity and switching characteristics. Experimental results verified benefits of GaN devices comparing to the appliance of Si switching devices with very good Figure Of Merit, for this particular application

Series combination of a switched dc-dc converter and a linear regulator for high frequency RF envelope amplifier

Classical linear amplifiers such as A, AB and B offer very good linearity suitable for RF power amplifiers. However, its inherent low efficiency limits its use especially in base-stations that manage tens or hundreds of Watts. The use of linearization techniques such as Envelope Elimination and Restoration (EER) allow an increase of efficiency keeping good linearity. This technique requires a very fast dc-dc power converter to provide variable voltage supply to the power amplifier. In this paper, several alternatives are analyzed to implement the envelope amplifier based on a cascade association of a switched dc-dc converter and a linear regulator. A simplified version of this approach is also suitable to operate with Envelope Tracking technique.

A Stress-Detection System Based on Physiological Signals and Fuzzy Logic

A stress-detection system is proposed based on physiological signals. Concretely, galvanic skin response (GSR) and heart rate (HR) are proposed to provide information on the state of mind of an individual, due to their nonintrusiveness and noninvasiveness. Furthermore, specific psychological experiments were designed to induce properly stress on individuals in order to acquire a database for training, validating, and testing the proposed system. Such system is based on fuzzy logic, and it described the behavior of an individual under stressing stimuli in terms of HR and GSR. The stress-detection accuracy obtained is 99.5% by acquiring HR and GSR during a period of 10 s, and what is more, rates over 90% of success are achieved by decreasing that acquisition period to 3-5 s. Finally, this paper comes up with a proposal that an accurate stress detection only requires two physiological signals, namely, HR and GSR, and the fact that the proposed stress-detection system is suitable for real-time applications.

Quantitative evaluation of artifact removal in real magnetoencephalogram signals with blind source separation

The magnetoencephalogram (MEG) is contaminated with undesired signals, which are called artifacts. Some of the most important ones are the cardiac and the ocular artifacts (CA and OA, respectively), and the power line noise (PLN). Blind source separation (BSS) has been used to reduce the influence of the artifacts in the data. There is a plethora of BSS-based artifact removal approaches, but few comparative analyses. In this study, MEG background activity from 26 subjects was processed with five widespread BSS (AMUSE, SOBI, JADE, extended Infomax, and FastICA) and one constrained BSS (cBSS) techniques. Then, the ability of several combinations of BSS algorithm, epoch length, and artifact detection metric to automatically reduce the CA, OA, and PLN were quantified with objective criteria. The results pinpointed to cBSS as a very suitable approach to remove the CA. Additionally, a combination of AMUSE or SOBI and artifact detection metrics based on entropy or power criteria decreased the OA. Finally, the PLN was reduced by means of a spectral metric. These findings confirm the utility of BSS to help in the artifact removal for MEG background activity.

WiMAX,Technology and Market.

Wireless communication is the transfer of information from one place to another without using wires. From the earliest times, humans have felt the need to develop techniques of remote communication. From this need arose the smoke signals, communication by sun reflection in mirrors and so on. But today the telecommunications electronic devices such as telephone, television, radio or computer. Radio and television are used for one-way communication. Telephone and computer are used for two-way communication. In wireless networks there is almost unlimited mobility, we can access the network almost anywhere or anytime. In wired networks we have the restriction of using the services in fixed area services. The demand of the wireless is increasing very fast; everybody wants broadband services anywhere anytime. WiMAX (Worldwide Interoperability for Microwave Access) is a broadband wireless technology based on IEEE 802.16-2004 and IEEE 802.16e-2005 that appears to solve this demand. WIMAX is a system that allows wireless data transmission in areas of up to 48 km of radius. It is designed as a wireless alternative to ADSL and a way to connect nodes in wireless metropolitan areas network. Unlike wireless systems that are limited in most cases, about 100 meter, providing greater coverage and more bandwidth. WIMAX promises to achieve high data transmission rates over large areas with a great amount of users. This alternative to the networks of broadband access common as DSL o Wi-Fi, can give broadband access to places quickly to rural areas and developing areas around the world. This paper is a study of WIMAX technology and market situation. First, the paper is responsible for explaining the technical aspects of WIMAX. For this gives an overview of WIMAX standards, physical layer, MAC layer and WiMAX, Technology and Market Beijing University of Post and Telecommunications 2 WIMAX network architecture. Second, the paper address the issue of market in which provides an overview of development and deployment of WIMAX to end the future development trend of WIMAX is addressed. RESUMEN: Por comunicaciones inalámbricas se entiende la transferencia de información desde un lugar a otro sin la necesidad de un soporte físico como es por ejemplo el cable. Por lo que remontándose a los principios de la existencia del ser humano, nos damos cuenta de que el ser humano siempre ha sentido la necesidad de desarrollar técnicas para lograr comunicarse a distancia con sus semejantes. De dicha necesidad, surgieron técnicas tan ancestrales como puede ser la comunicación mediante señales de humo o por reflexión de los rayos solares en espejos entre otras. La curiosidad del ser humano y la necesidad de comunicarse a distancia fue la que llevó a Alexander Graham Bell a inventar el teléfono en 1876. La aparición de un dispositivo que permitía comunicarse a distancia permitiendo escuchar la voz de aquella persona con la que se quería hablar, supuso una revolución no solo en el panorama tecnológico, si no también en el panorama social. Pues a parte de permitir comunicaciones a larga distancia, solventó el problema de la comunicación en “tiempo real”. A raíz de este invento, la tecnología en materia de comunicación ha ido avanzando significativamente, más concretamente en lo referido a las comunicaciones inalámbricas. En 1973 se realizó la primera llamada desde un terminal móvil aunque no fue hasta 1983 cuando se empezó a comercializar dicho terminal, lo que supuso un cambio de hábitos y costumbres para la sociedad. Desde la aparición del primer móvil el crecimiento del mercado ha sido exponencial, lo que ha repercutido en una demanda impensable de nuevas aplicaciones integradas en dichos dispositivos móviles que satisfagan las necesidades que día a día autogenera la sociedad. Tras conseguir realizar llamadas a larga distancia de forma inalámbrica, el siguiente paso fue la creación de los SMS (Short Message System) lo que supuso una nueva revolución además de abaratar costes al usuario a la hora de comunicarse. Pero el gran reto para la industria de las comunicaciones móviles surgió con la aparición de internet. Todo el mundo sentía la necesidad de poder conectarse a esa gran base de datos que es internet en cualquier parte y en cualquier momento. Las primeras conexiones a internet desde dispositivos móviles se realizaron a través de la tecnología WAP (Wireless Application Protocol) hasta la aparición de la tecnología GPRS que permitía la conexión mediante protocolo TCP/IP. A partir de estas conexiones han surgido otras tecnologías, como EDGE, HSDPA, etc., que permitían y permiten la conexión a internet desde dispositivos móviles. Hoy en día la demanda de servicios de red inalámbrica crece de forma rápida y exponencial, todo el mundo quiere servicios de banda ancha en cualquier lugar y en cualquier momento. En este documento se analiza la tecnología WiMAX ( Worldwide Interoperability for Microwave Access) que es una tecnología de banda ancha basada en el estándar IEEE 802.16 creada para brindar servicios a la demanda emergente en la banda ancha desde un punto de vista tecnológico, donde se da una visión de la parte técnica de la tecnología; y desde el punto de vista del mercado, donde se analiza el despliegue y desarrollo de la tecnología desde el punto de vista de negocio. WiMAX es una tecnología que permite la transmisión inalámbrica de datos en áreas de hasta 48Km de radio y que está diseñada como alternativa inalámbrica para ADSL y para conectar nodos de red inalámbrica en áreas metropolitanas. A diferencia de los sistemas inalámbricos existentes que están limitados en su mayoría a unos cientos de metros, WiMAX ofrece una mayor cobertura y un mayor ancho de banda que permita dar soporte a nuevas aplicaciones, además de alcanzar altas tasas de transmisión de datos en grandes áreas con una gran cantidad de usuarios. Se trata de una alternativa a las redes de acceso de banda ancha como DSL o Wi-Fi, que puede dar acceso de banda ancha a lugares tales como zonas rurales o zonas en vías de desarrollo por todo el mundo con rapidez. Existen dos tecnologías de WiMAX, WiMAX fijo (basado en el estándar IEEE 802.16d-2004) y WiMAX móvil (basado en el estándar IEEE 802.16e-2005). La tecnología fija está diseñada para comunicaciones punto a multipunto, mientras que la fija lo está para comunicaciones multipunto a multipunto. WiMAX móvil se basa en la tecnología OFDM que ofrece ventajas en términos de latencia, eficiencia en el uso del espectro y soporte avanzado para antenas. La modulación OFDM es muy robusta frente al multitrayecto, que es muy habitual en los canales de radiodifusión, frente al desvanecimiento debido a las condiciones meteorológicas y frente a las interferencias de RF. Una vez creada la tecnología WiMAX, poseedora de las características idóneas para solventar la demanda del mercado, ha de darse el siguiente paso, hay que convencer a la industria de las telecomunicaciones de que dicha tecnología realmente es la solución para que apoyen su implantación en el mercado de la banda ancha para las redes inalámbricas. Es aquí donde entra en juego el estudio del mercado que se realiza en este documento. WiMAX se enfrenta a un mercado exigente en el que a parte de tener que dar soporte a la demanda técnica, ha de ofrecer una rentabilidad económica a la industria de las comunicaciones móviles y más concretamente a las operadoras móviles que son quienes dentro del sector de las telecomunicaciones finalmente han de confiar en la tecnología para dar soporte a sus usuarios ya que estos al fin y al cabo lo único que quieren es que su dispositivo móvil satisfaga sus necesidades independientemente de la tecnología que utilicen para tener acceso a la red inalámbrica de banda ancha. Quizás el mayor problema al que se ha enfrentado WiMAX haya sido la situación económica en la que se encuentra el mundo. WiMAX a comenzado su andadura en uno de los peores momentos, pero aun así se presenta como una tecnología capaz de ayudar al mundo a salir hacia delante en estos tiempos tan duros. Finalmente se analiza uno de los debates existentes hoy en día en el sector de las comunicaciones móviles, WiMAX vs. LTE. Como se puede observar en el documento realmente una tecnología no saldrá victoriosa frente a la otra, si no que ambas tecnologías podrán coexistir y trabajar de forma conjunta.

Estimation of functional connectivity from electromagnetic signals and the amount of empirical data required

An increasing number of neuroimaging studies are concerned with the identification of interactions or statistical dependencies between brain areas. Dependencies between the activities of different brain regions can be quantified with functional connectivity measures such as the cross-correlation coefficient. An important factor limiting the accuracy of such measures is the amount of empirical data available. For event-related protocols, the amount of data also affects the temporal resolution of the analysis. We use analytical expressions to calculate the amount of empirical data needed to establish whether a certain level of dependency is significant when the time series are autocorrelated, as is the case for biological signals. These analytical results are then contrasted with estimates from simulations based on real data recorded with magnetoencephalography during a resting-state paradigm and during the presentation of visual stimuli. Results indicate that, for broadband signals, 50–100 s of data is required to detect a true underlying cross-correlations coefficient of 0.05. This corresponds to a resolution of a few hundred milliseconds for typical event-related recordings. The required time window increases for narrow band signals as frequency decreases. For instance, approximately 3 times as much data is necessary for signals in the alpha band. Important implications can be derived for the design and interpretation of experiments to characterize weak interactions, which are potentially important for brain processing.

A new feature extraction method for signal classification applied to cat spinal cord signals

In the spinal cord of the anesthetized cat, spontaneous cord dorsum potentials (CDPs) appear synchronously along the lumbo-sacral segments. These CDPs have different shapes and magnitudes. Previous work has indicated that some CDPs appear to be specially associated with the activation of spinal pathways that lead to primary afferent depolarization and presynaptic inhibition. Visual detection and classification of these CDPs provides relevant information on the functional organization of the neural networks involved in the control of sensory information and allows the characterization of the changes produced by acute nerve and spinal lesions. We now present a novel feature extraction approach for signal classification, applied to CDP detection. The method is based on an intuitive procedure. We first remove by convolution the noise from the CDPs recorded in each given spinal segment. Then, we assign a coefficient for each main local maximum of the signal using its amplitude and distance to the most important maximum of the signal. These coefficients will be the input for the subsequent classification algorithm. In particular, we employ gradient boosting classification trees. This combination of approaches allows a faster and more accurate discrimination of CDPs than is obtained by other methods.

Analysis and design of multirate synchronous sampling schemes for sparse multiband signals

We consider the problem of developing efficient sampling schemes for multiband sparse signals. Previous results on multicoset sampling implementations that lead to universal sampling patterns (which guarantee perfect reconstruction), are based on a set of appropriate interleaved analog to digital converters, all of them operating at the same sampling frequency. In this paper we propose an alternative multirate synchronous implementation of multicoset codes, that is, all the analog to digital converters in the sampling scheme operate at different sampling frequencies, without need of introducing any delay. The interleaving is achieved through the usage of different rates, whose sum is significantly lower than the Nyquist rate of the multiband signal. To obtain universal patterns the sampling matrix is formulated and analyzed. Appropriate choices of the parameters, that is the block length and the sampling rates, are also proposed.

Design of universal multicoset sampling patterns for compressed sensing of multiband sparse signals

Many problems in digital communications involve wideband radio signals. As the most recent example, the impressive advances in Cognitive Radio systems make even more necessary the development of sampling schemes for wideband radio signals with spectral holes. This is equivalent to considering a sparse multiband signal in the framework of Compressive Sampling theory. Starting from previous results on multicoset sampling and recent advances in compressive sampling, we analyze the matrix involved in the corresponding reconstruction equation and define a new method for the design of universal multicoset codes, that is, codes guaranteeing perfect reconstruction of the sparse multiband signal.