Enhancing spiral-wound ultrafiltration performance for direct drinking water treatment through operational procedures improvement: A feasible option for the Sao Paulo Metropolitan Region

This work aimed to evaluate the influence of specific operational conditions on the performance of a spiral-wound ultrafiltration pilot plant for direct drinking water treatment, installed at the Guarapiranga's reservoir, in the Sao Paulo Metropolitan Region. Results from operational tests showed that the volume of permeate produced in the combination of periodic relaxation with flushing and chlorine dosage procedures was 49% higher than the volume obtained when these procedures were not used. Two years of continuous operation demonstrated that the ultrafiltration pilot plant performed better during fall and winter seasons, higher permeate flow production and reduced chemical cleanings frequency. Observed behavior seems to be associated with the algae bloom events in the reservoir, which are more frequent during spring and summer seasons, confirmed by chlorophyll-a analysis results. Concentrate clarification using ferric chloride was quite effective in removing NOM and turbidity, allowing its recirculation to the ultrafiltration feed tank. This procedure made it possible to reach almost 99% water recovery considering a single 54-hour recirculation cycle. Water quality monitoring demonstrated that the ultrafiltration pilot plant was quite efficient, and that potential pathogenic organisms, Escherichia coil and total coliforms, turbidity and apparent color removals were 100%, 95.1%, and 91.5%, respectively. (C) 2012 Elsevier B.V. All rights reserved.

Heat stress impairs performance and induces intestinal inflammation in broiler chickens infected with Salmonella Enteritidis

Stressful situations reduce the welfare, production indices and immune status of chickens. Salmonella spp. are a major zoonotic pathogens that annually cause over 1 billion infections worldwide. We therefore designed the current experiment to analyse the effects of 31 +/- 1 degrees C heat stress (HS) (from 35 to 41 days) on performance parameters, Salmonella invasion and small intestine integrity in broiler chickens infected with Salmonella Enteritidis. We observed that HS decreased body weight gain and feed intake. However, feed conversion was only increased when HS was combined with Salmonella Enteritidis infection. In addition, we observed an increase in serum corticosterone levels in all of the birds that were subjected to HS, showing a hypothalamus-pituitary-adrenal axis activation. Furthermore, mild acute multifocal lymphoplasmacytic enteritis, characterized by foci of heterophil infiltration in the duodenum, jejunum and ileum, was observed in the HS group. In contrast, similar but more evident enteritis was noted in the heat-stressed and Salmonella-infected group. In this group, moderate enteritis was observed in all parts of the small intestine. Lastly, we observed an increase in Salmonella counts in the spleens of the stressed and Salmonella-infected chickens. The combination of HS and Salmonella Enteritidis infection may therefore disrupt the intestinal barrier, which would allow pathogenic bacteria to migrate through the intestinal mucosa to the spleen and generate an inflammatory infiltrate in the gut, decreasing performance parameters.

Glycerine derived from biodiesel production as a feedstuff for broiler diets

The performance, carcass traits, and litter humidity of broilers fed increasing levels of glycerine derived from biodiesel production were evaluated. In this experiment, 1,575 broilers were distributed according to a completely randomized experimental design into five treatments with seven replicates of 45 birds each. Treatments consisted of a control diet and four diets containing 2.5, 5.0, 7.5, or 10% glycerine. The experimental diets contained equal nutritional levels and were based on corn, soybean meal and soybean oil. The glycerine included in the diets contained 83.4% glycerol, 1.18% sodium, and 208 ppm methanol, and a calculated energy value of 3,422 kcal AMEn/kg. Performance parameters (weight gain, feed intake, feed conversion ratio, live weight, and livability) were monitored when broilers were 7, 21, and 42 days of age. On day 43, litter humidity was determined in each pen, and 14 birds/treatment were sacrificed for the evaluation of carcass traits. During the period of 1 to 7 days, there was a positive linear effect of the treatments on weight gain, feed intake, and live weight gain. Livability linearly decreased during the period of 1 to 21 days. During the entire experimental period, no significant effects were observed on performance parameters or carcass traits, but there was a linear increase in litter humidity. Therefore, the inclusion of up to 5% glycerine in the diet did not affect broiler performance during the total rearing period.

Global trade, food production and ecosystem support : Making the interactions visible

Modern food production is a complex, globalized system in which what we eat and how it is produced are increasingly disconnected. This thesis examines some of the ways in which global trade has changed the mix of inputs to food and feed, and how this affects food security and our perceptions of sustainability. One useful indicator of the ecological impact of trade in food and feed products is the Appropriated Ecosystem Areas (ArEAs), which estimates the terrestrial and aquatic areas needed to produce all the inputs to particular products. The method is introduced in Paper I and used to calculate and track changes in imported subsidies to Swedish agriculture over the period 1962-1994. In 1994, Swedish consumers needed agricultural areas outside their national borders to satisfy more than a third of their food consumption needs. The method is then applied to Swedish meat production in Paper II to show that the term “Made in Sweden” is often a misnomer. In 1999, almost 80% of manufactured feed for Swedish pigs, cattle and chickens was dependent on imported inputs, mainly from Europe, Southeast Asia and South America. Paper III examines ecosystem subsidies to intensive aquaculture in two nations: shrimp production in Thailand and salmon production in Norway. In both countries, aquaculture was shown to rely increasingly on imported subsidies. The rapid expansion of aquaculture turned these countries from fishmeal net exporters to fishmeal net importers, increasingly using inputs from the Southeastern Pacific Ocean. As the examined agricultural and aquacultural production systems became globalized, levels of dependence on other nations’ ecosystems, the number of external supply sources, and the distance to these sources steadily increased. Dependence on other nations is not problematic, as long as we are able to acknowledge these links and sustainably manage resources both at home and abroad. However, ecosystem subsidies are seldom recognized or made explicit in national policy or economic accounts. Economic systems are generally not designed to receive feedbacks when the status of remote ecosystems changes, much less to respond in an ecologically sensitive manner. Papers IV and V discuss the problem of “masking” of the true environmental costs of production for trade. One of our conclusions is that, while the ArEAs approach is a useful tool for illuminating environmentally-based subsidies in the policy arena, it does not reflect all of the costs. Current agricultural and aquacultural production methods have generated substantial increases in production levels, but if policy continues to support the focus on yield and production increases alone, taking the work of ecosystems for granted, vulnerability can result. Thus, a challenge is to develop a set of complementary tools that can be used in economic accounting at national and international scales that address ecosystem support and performance. We conclude that future resilience in food production systems will require more explicit links between consumers and the work of supporting ecosystems, locally and in other regions of the world, and that food security planning will require active management of the capacity of all involved ecosystems to sustain food production.

Anaerobic energy provision does not limit Wingate exercise performance in endurance-trained cyclists

[EN] The aim of this study was to evaluate the effects of severe acute hypoxia on exercise performance and metabolism during 30-s Wingate tests. Five endurance- (E) and five sprint- (S) trained track cyclists from the Spanish National Team performed 30-s Wingate tests in normoxia and hypoxia (inspired O(2) fraction = 0.10). Oxygen deficit was estimated from submaximal cycling economy tests by use of a nonlinear model. E cyclists showed higher maximal O(2) uptake than S (72 +/- 1 and 62 +/- 2 ml x kg(-1) x min(-1), P < 0.05). S cyclists achieved higher peak and mean power output, and 33% larger oxygen deficit than E (P < 0.05). During the Wingate test in normoxia, S relied more on anaerobic energy sources than E (P < 0.05); however, S showed a larger fatigue index in both conditions (P < 0.05). Compared with normoxia, hypoxia lowered O(2) uptake by 16% in E and S (P < 0.05). Peak power output, fatigue index, and exercise femoral vein blood lactate concentration were not altered by hypoxia in any group. Endurance cyclists, unlike S, maintained their mean power output in hypoxia by increasing their anaerobic energy production, as shown by 7% greater oxygen deficit and 11% higher postexercise lactate concentration. In conclusion, performance during 30-s Wingate tests in severe acute hypoxia is maintained or barely reduced owing to the enhancement of the anaerobic energy release. The effect of severe acute hypoxia on supramaximal exercise performance depends on training background.

Physiology and Biotechnology of the Hydrogen Production with the Green Microalga Chlamydomonas reinhardtii

The hydrogen production in the green microalga Chlamydomonas reinhardtii was evaluated by means of a detailed physiological and biotechnological study. First, a wide screening of the hydrogen productivity was done on 22 strains of C. reinhardtii, most of which mutated at the level of the D1 protein. The screening revealed for the first time that mutations upon the D1 protein may result on an increased hydrogen production. Indeed, productions ranged between 0 and more than 500 mL hydrogen per liter of culture (Torzillo, Scoma et al., 2007a), the highest producer (L159I-N230Y) being up to 5 times more performant than the strain cc124 widely adopted in literature (Torzillo, Scoma, et al., 2007b). Improved productivities by D1 protein mutants were generally a result of high photosynthetic capabilities counteracted by high respiration rates. Optimization of culture conditions were addressed according to the results of the physiological study of selected strains. In a first step, the photobioreactor (PBR) was provided with a multiple-impeller stirring system designed, developed and tested by us, using the strain cc124. It was found that the impeller system was effectively able to induce regular and turbulent mixing, which led to improved photosynthetic yields by means of light/dark cycles. Moreover, improved mixing regime sustained higher respiration rates, compared to what obtained with the commonly used stir bar mixing system. As far as the results of the initial screening phase are considered, both these factors are relevant to the hydrogen production. Indeed, very high energy conversion efficiencies (light to hydrogen) were obtained with the impeller device, prooving that our PBR was a good tool to both improve and study photosynthetic processes (Giannelli, Scoma et al., 2009). In the second part of the optimization, an accurate analysis of all the positive features of the high performance strain L159I-N230Y pointed out, respect to the WT, it has: (1) a larger chlorophyll optical cross-section; (2) a higher electron transfer rate by PSII; (3) a higher respiration rate; (4) a higher efficiency of utilization of the hydrogenase; (5) a higher starch synthesis capability; (6) a higher per cell D1 protein amount; (7) a higher zeaxanthin synthesis capability (Torzillo, Scoma et al., 2009). These information were gathered with those obtained with the impeller mixing device to find out the best culture conditions to optimize productivity with strain L159I-N230Y. The main aim was to sustain as long as possible the direct PSII contribution, which leads to hydrogen production without net CO2 release. Finally, an outstanding maximum rate of 11.1 ± 1.0 mL/L/h was reached and maintained for 21.8 ± 7.7 hours, when the effective photochemical efficiency of PSII (ΔF/F'm) underwent a last drop to zero. If expressed in terms of chl (24.0 ± 2.2 µmoles/mg chl/h), these rates of production are 4 times higher than what reported in literature to date (Scoma et al., 2010a submitted). DCMU addition experiments confirmed the key role played by PSII in sustaining such rates. On the other hand, experiments carried out in similar conditions with the control strain cc124 showed an improved final productivity, but no constant PSII direct contribution. These results showed that, aside from fermentation processes, if proper conditions are supplied to selected strains, hydrogen production can be substantially enhanced by means of biophotolysis. A last study on the physiology of the process was carried out with the mutant IL. Although able to express and very efficiently utilize the hydrogenase enzyme, this strain was unable to produce hydrogen when sulfur deprived. However, in a specific set of experiments this goal was finally reached, pointing out that other than (1) a state 1-2 transition of the photosynthetic apparatus, (2) starch storage and (3) anaerobiosis establishment, a timely transition to the hydrogen production is also needed in sulfur deprivation to induce the process before energy reserves are driven towards other processes necessary for the survival of the cell. This information turned out to be crucial when moving outdoor for the hydrogen production in a tubular horizontal 50-liter PBR under sunlight radiation. First attempts with laboratory grown cultures showed that no hydrogen production under sulfur starvation can be induced if a previous adaptation of the culture is not pursued outdoor. Indeed, in these conditions the hydrogen production under direct sunlight radiation with C. reinhardtii was finally achieved for the first time in literature (Scoma et al., 2010b submitted). Experiments were also made to optimize productivity in outdoor conditions, with respect to the light dilution within the culture layers. Finally, a brief study of the anaerobic metabolism of C. reinhardtii during hydrogen oxidation has been carried out. This study represents a good integration to the understanding of the complex interplay of pathways that operate concomitantly in this microalga.

A candidate gene approach to identify DNA markers associated with meat quality and production traits: investigation of several cathepsin genes in Italian heavy pigs.

The cathepsin enzymes represent an important family of lysosomal proteinases with a broad spectrum of functions in many, if not in all, tissues and cell types. In addition to their primary role during the normal protein turnover, they possess highly specific proteolytic activities, including antigen processing in the immune response and a direct role in the development of obesity and tumours. In pigs, the involvement of cathepsin enzymes in proteolytic processes have important effects during the conversion of muscle to meat, due to their influence on meat texture and sensory characteristics, mainly in seasoned products. Their contribution is fundamental in flavour development of dry-curing hams. However, several authors have demonstrated that high cathepsin activity, in particular of cathepsin B, is correlated to defects of these products, such as an excessive meat softness together with abnormal free tyrosine content, astringent or metallic aftertastes and formation of a white film on the cut surface. Thus, investigation of their genetic variability could be useful to identify DNA markers associated with these dry cured hams parameters, but also with meat quality, production and carcass traits in Italian heavy pigs. Unfortunately, no association has been found between cathepsin markers and meat quality traits so far, in particular with cathepsin B activity, suggesting that other genes, besides these, affect meat quality parameters. Nevertheless, significant associations were observed with several carcass and production traits in pigs. A recent study has demonstrated that different single nucleotide polymorphisms (SNPs) localized in cathepsin D (CTSD), F (CTSF), H and Z genes were highly associated with growth, fat deposition and production traits in an Italian Large White pig population. The aim of this thesis was to confirm some of these results in other pig populations and identify new cathepsin markers in order to evaluate their effects on cathepsin activity and other production traits. Furthermore, starting from the data obtained in previous studies on CTSD gene, we also analyzed the known polymorphism located in the insulin-like growth factor 2 gene (IGF2 intron3-g.3072G>A). This marker is considered the causative mutation for the quantitative trait loci (QTL) affecting muscle mass and fat deposition in pigs. Since IGF2 maps very close to CTSD on porcine chromosome (SSC) 2, we wanted to clarify if the effects of the CTSD marker were due to linkage disequilibrium with the IGF2 intron3-g.3072G>A mutation or not. In the first chapter, we reported the results from these two SSC2 gene markers. First of all, we evaluated the effects of the IGF2 intron3-g.3072G>A polymorphism in the Italian Large White breed, for which no previous studies have analysed this marker. Highly significant associations were identified with all estimated breeding values for production and carcass traits (P<0.00001), while no effects were observed for meat quality traits. Instead, the IGF2 intron3-g.3072G>A mutation did not show any associations with the analyzed traits in the Italian Duroc pigs, probably due to the low level of variability at this polymorphic site for this breed. In the same Duroc pig population, significant associations were obtained for the CTSD marker for all production and carcass traits (P < 0.001), after excluding possible confounding effects of the IGF2 mutation. The effects of the CTSD g.70G>A polymorphism were also confirmed in a group of Italian Large White pigs homozygous for the IGF2 intron3-g.3072G allele G (IGF2 intron3-g.3072GG) and by haplotype analysis between the markers of the two considered genes. Taken together, all these data indicated that the IGF2 intron3-g.3072G>A mutation is not the only polymorphism affecting fatness and muscle deposition in pigs. In the second chapter, we reported the analysis of two new SNPs identified in cathepsin L (CTSL) and cathepsin S (CTSS) genes and the association results with meat quality parameters (including cathepsin B activity) and several production traits in an Italian Large White pig population. Allele frequencies of these two markers were evaluated in 7 different pig breeds. Furthermore, we mapped using a radiation hybrid panel the CTSS gene on SSC4. Association studies with several production traits, carried out in 268 Italian Large White pigs, indicated positive effects of the CTSL polymorphism on average daily gain, weight of lean cuts and backfat thickness (P<0.05). The results for these latter traits were also confirmed using a selective genotype approach in other Italian Large White pigs (P<0.01). In the 268 pig group, the CTSS polymorphism was associated with feed:gain ratio and average daily gain (P<0.05). Instead, no association was observed between the analysed markers and meat quality parameters. Finally, we wanted to verify if the positive results obtained for the cathepsin L and S markers and for other previous identified SNPs (cathepsin F, cathepsin Z and their inhibitor cystatin B) were confirmed in the Italian Duroc pig breed (third chapter). We analysed them in two groups of Duroc pigs: the first group was made of 218 performance-tested pigs not selected by any phenotypic criteria, the second group was made of 100 Italian Duroc pigs extreme and divergent for visible intermuscular fat trait. In the first group, the CTSL polymorphism was associated with weight of lean cuts (P<0.05), while suggestive associations were obtained for average daily gain and backfat thickness (P<0.10). Allele frequencies of the CTSL gene marker also differed positively among the visible intermuscular extreme tails. Instead, no positive effects were observed for the other DNA markers on the analysed traits. In conclusion, in agreement with the present data and for the biological role of these enzymes, the porcine CTSD and CTSL markers: a) may have a direct effect in the biological mechanisms involved in determining fat and lean meat content in pigs, or b) these markers could be very close to the putative functional mutation(s) present in other genes. These findings have important practical applications, in particular the CTSD and CTSL mutations could be applied in a marker assisted selection (MAS) both in the Italian Large White and Italian Duroc breeds. Marker assisted selection could also increase in efficiency by adding information from the cathepsin S genotype, but only in the Italian Large White breed.

Different approaches to identify markers for meat quality and production traits in pigs: analysis of the transcriptome in post mortem skeletal muscle and investigation of candidate genes

Due to the growing attention of consumers towards their food, improvement of quality of animal products has become one of the main focus of research. To this aim, the application of modern molecular genetics approaches has been proved extremely useful and effective. This innovative drive includes all livestock species productions, including pork. The Italian pig breeding industry is unique because needs heavy pigs slaughtered at about 160 kg for the production of high quality processed products. For this reason, it requires precise meat quality and carcass characteristics. Two aspects have been considered in this thesis: the application of the transcriptome analysis in post mortem pig muscles as a possible method to evaluate meat quality parameters related to the pre mortem status of the animals, including health, nutrition, welfare, and with potential applications for product traceability (chapters 3 and 4); the study of candidate genes for obesity related traits in order to identify markers associated with fatness in pigs that could be applied to improve carcass quality (chapters 5, 6, and 7). Chapter three addresses the first issue from a methodological point of view. When we considered this issue, it was not obvious that post mortem skeletal muscle could be useful for transcriptomic analysis. Therefore we demonstrated that the quality of RNA extracted from skeletal muscle of pigs sampled at different post mortem intervals (20 minutes, 2 hours, 6 hours, and 24 hours) is good for downstream applications. Degradation occurred starting from 48 h post mortem even if at this time it is still possible to use some RNA products. In the fourth chapter, in order to demonstrate the potential use of RNA obtained up to 24 hours post mortem, we present the results of RNA analysis with the Affymetrix microarray platform that made it possible to assess the level of expression of more of 24000 mRNAs. We did not identify any significant differences between the different post mortem times suggesting that this technique could be applied to retrieve information coming from the transcriptome of skeletal muscle samples not collected just after slaughtering. This study represents the first contribution of this kind applied to pork. In the fifth chapter, we investigated as candidate for fat deposition the TBC1D1 [TBC1 (tre-2/USP6, BUB2, cdc16) gene. This gene is involved in mechanisms regulating energy homeostasis in skeletal muscle and is associated with predisposition to obesity in humans. By resequencing a fragment of the TBC1D1 gene we identified three synonymous mutations localized in exon 2 (g.40A>G, g.151C>T, and g.172T>C) and 2 polymorphisms localized in intron 2 (g.219G>A and g.252G>A). One of these polymorphisms (g.219G>A) was genotyped by high resolution melting (HRM) analysis and PCR-RFLP. Moreover, this gene sequence was mapped by radiation hybrid analysis on porcine chromosome 8. The association study was conducted in 756 performance tested pigs of Italian Large White and Italian Duroc breeds. Significant results were obtained for lean meat content, back fat thickness, visible intermuscular fat and ham weight. In chapter six, a second candidate gene (tribbles homolog 3, TRIB3) is analyzed in a study of association with carcass and meat quality traits. The TRIB3 gene is involved in energy metabolism of skeletal muscle and plays a role as suppressor of adipocyte differentiation. We identified two polymorphisms in the first coding exon of the porcine TRIB3 gene, one is a synonymous SNP (c.132T> C), a second is a missense mutation (c.146C> T, p.P49L). The two polymorphisms appear to be in complete linkage disequilibrium between and within breeds. The in silico analysis of the p.P49L substitution suggests that it might have a functional effect. The association study in about 650 pigs indicates that this marker is associated with back fat thickness in Italian Large White and Italian Duroc breeds in two different experimental designs. This polymorphisms is also associated with lactate content of muscle semimembranosus in Italian Large White pigs. Expression analysis indicated that this gene is transcribed in skeletal muscle and adipose tissue as well as in other tissues. In the seventh chapter, we reported the genotyping results for of 677 SNPs in extreme divergent groups of pigs chosen according to the extreme estimated breeding values for back fat thickness. SNPs were identified by resequencing, literature mining and in silico database mining. analysis, data reported in the literature of 60 candidates genes for obesity. Genotyping was carried out using the GoldenGate (Illumina) platform. Of the analyzed SNPs more that 300 were polymorphic in the genotyped population and had minor allele frequency (MAF) >0.05. Of these SNPs, 65 were associated (P<0.10) with back fat thickness. One of the most significant gene marker was the same TBC1D1 SNPs reported in chapter 5, confirming the role of this gene in fat deposition in pig. These results could be important to better define the pig as a model for human obesity other than for marker assisted selection to improve carcass characteristics.

Percorsi di gender performance: fotografia tra arte e moda dagli anni Novanta ad oggi

My project explores and compares different forms of gender performance in contemporary art and visual culture according to a perspective centered on photography. Thanks to its attesting power this medium can work as a ready-made. In fact during the 20th century it played a key role in the cultural emancipation of the body which (using a Michel Foucault’s expression) has now become «the zero point of the world». Through performance the body proves to be a living material of expression and communication while photography ensures the recording of any ephemeral event that happens in time and space. My questioning approach considers the gender constructed imagery from the 1990s to the present in order to investigate how photography’s strong aura of realism promotes and allows fantasies of transformation. The contemporary fascination with gender (especially for art and fashion) represents a crucial issue in the global context of postmodernity and is manifested in a variety of visual media, from photography to video and film. Moreover the internet along with its digital transmission of images has deeply affected our world (from culture to everyday life) leading to a postmodern preference for performativity over the more traditional and linear forms of narrativity. As a consequence individual borders get redefined by the skin itself which (dissected through instant vision) turns into a ductile material of mutation and hybridation in the service of identity. My critical assumptions are taken from the most relevant changes occurred in philosophy during the last two decades as a result of the contributions by Jacques Lacan, Michel Foucault, Jacques Derrida, Gilles Deleuze who developed a cross-disciplinary and comparative approach to interpret the crisis of modernity. They have profoundly influenced feminist studies so that the category of gender has been reassessed in contrast with sex (as a biological connotation) and in relation to history, culture, society. The ideal starting point of my research is the year 1990. I chose it as the approximate historical moment when the intersection of race, class and gender were placed at the forefront of international artistic production concerned with identity, diversity and globalization. Such issues had been explored throughout the 1970s but it was only from the mid-1980s onward that they began to be articulated more consistently. Published in 1990, the book "Gender trouble: feminism and the subversion of identity" by Judith Butler marked an important breakthrough by linking gender to performance as well as investigating the intricate connections between theory and practice, embodiment and representation. It inspired subsequent research in a variety of disciplines, art history included. In the same year Teresa de Lauretis launched the definition of queer theory to challenge the academic perspective in gay and lesbian studies. In the meantime the rise of Third Wave Feminism in the US introduced a racially and sexually inclusive vision over the global situation in order to reflect on subjectivity, new technologies and popular culture in connection with gender representation. These conceptual tools have enabled prolific readings of contemporary cultural production whether fine arts or mass media. After discussing the appropriate framework of my project and taking into account the postmodern globalization of the visual, I have turned to photography to map gender representation both in art and in fashion. Therefore I have been creating an archive of images around specific topics. I decided to include fashion photography because in the 1990s this genre moved away from the paradigm of an idealized and classical beauty toward a new vernacular allied with lifestyles, art practices, pop and youth culture; as one might expect the dominant narrative modes in fashion photography are now mainly influenced by cinema and snapshot. These strategies originate story lines and interrupted narratives using models’ performance to convey a particular imagery where identity issues emerge as an essential part of fashion spectacle. Focusing on the intersections of gender identities with socially and culturally produced identities, my approach intends to underline how the fashion world has turned to current trends in art photography and in some case turned to the artists themselves. The growing fluidity of the categories that distinguish art from fashion photography represents a particularly fruitful moment of visual exchange. Varying over time the dialogue between these two fields has always been vital; nowadays it can be studied as a result of this close relationship between contemporary art world and consumer culture. Due to the saturation of postmodern imagery the feedback between art and fashion has become much more immediate and then increasingly significant for anyone who wants to investigate the construction of gender identity through performance. In addition to that a lot of magazines founded in the 1990s bridged the worlds of art and fashion because some of their designers and even editors were art-school graduates encouraging innovation. The inclusion of art within such magazines aimed at validating them as a form of art in themselves supporting a dynamic intersection for music, fashion, design and youth culture: an intersection that also contributed to create and spread different gender stereotypes. This general interest in fashion produced many exhibitions of and about fashion itself at major international venues such as the Victoria and Albert Museum in London, the Metropolitan Museum of Art and the Solomon R. Guggenheim Museum in New York. Since then this celebrated success of fashion has been regarded as a typical element of postmodern culture. Owing to that I have also based my analysis on some important exhibitions dealing with gender performance like "Féminin-Masculin" at the Centre Pompidou of Paris (1995), "Rrose is a Rrose is a Rrose. Gender performance in photography" at the Solomon R. Guggenheim Museum of New York (1997), "Global Feminisms" at the Brooklyn Museum (2007), "Female Trouble" at the Pinakothek der Moderne in München together with the workshops dedicated to "Performance: gender and identity" in June 2005 at the Tate Modern of London. Since 2003 in Italy we have had Gender Bender - an international festival held annually in Bologna - to explore the gender imagery stemming from contemporary culture. In few days this festival offers a series of events ranging from visual arts, performance, cinema, literature to conferences and music. Being aware that any method of research is neither race nor gender neutral I have traced these critical paths to question gender identity in a multicultural perspective taking account of the political implications too. In fact, if visibility may be equated with exposure, we can also read these images as points of intersection of visibility with social power. Since gender assignations rely so heavily on the visual, the postmodern dismantling of gender certainty through performance has wide-ranging effects that need to be analyzed. In some sense this practice can even contest the dominance of visual within postmodernism. My visual map in contemporary art and fashion photography includes artists like Nan Goldin, Cindy Sherman, Hellen van Meene, Rineke Dijkstra, Ed Templeton, Ryan McGinley, Anne Daems, Miwa Yanagi, Tracey Moffat, Catherine Opie, Tomoko Sawada, Vanessa Beecroft, Yasumasa Morimura, Collier Schorr among others.

Performance evaluation of low environmental impact asphalt concretes using the mechanistic empirical design method based on laboratory fatigue and permanent deformation models

The "sustainability" concept relates to the prolonging of human economic systems with as little detrimental impact on ecological systems as possible. Construction that exhibits good environmental stewardship and practices that conserve resources in a manner that allow growth and development to be sustained for the long-term without degrading the environment are indispensable in a developed society. Past, current and future advancements in asphalt as an environmentally sustainable paving material are especially important because the quantities of asphalt used annually in Europe as well as in the U.S. are large. The asphalt industry is still developing technological improvements that will reduce the environmental impact without affecting the final mechanical performance. Warm mix asphalt (WMA) is a type of asphalt mix requiring lower production temperatures compared to hot mix asphalt (HMA), while aiming to maintain the desired post construction properties of traditional HMA. Lowering the production temperature reduce the fuel usage and the production of emissions therefore and that improve conditions for workers and supports the sustainable development. Even the crumb-rubber modifier (CRM), with shredded automobile tires and used in the United States since the mid 1980s, has proven to be an environmentally friendly alternative to conventional asphalt pavement. Furthermore, the use of waste tires is not only relevant in an environmental aspect but also for the engineering properties of asphalt [Pennisi E., 1992]. This research project is aimed to demonstrate the dual value of these Asphalt Mixes in regards to the environmental and mechanical performance and to suggest a low environmental impact design procedure. In fact, the use of eco-friendly materials is the first phase towards an eco-compatible design but it cannot be the only step. The eco-compatible approach should be extended also to the design method and material characterization because only with these phases is it possible to exploit the maximum potential properties of the used materials. Appropriate asphalt concrete characterization is essential and vital for realistic performance prediction of asphalt concrete pavements. Volumetric (Mix design) and mechanical (Permanent deformation and Fatigue performance) properties are important factors to consider. Moreover, an advanced and efficient design method is necessary in order to correctly use the material. A design method such as a Mechanistic-Empirical approach, consisting of a structural model capable of predicting the state of stresses and strains within the pavement structure under the different traffic and environmental conditions, was the application of choice. In particular this study focus on the CalME and its Incremental-Recursive (I-R) procedure, based on damage models for fatigue and permanent shear strain related to the surface cracking and to the rutting respectively. It works in increments of time and, using the output from one increment, recursively, as input to the next increment, predicts the pavement conditions in terms of layer moduli, fatigue cracking, rutting and roughness. This software procedure was adopted in order to verify the mechanical properties of the study mixes and the reciprocal relationship between surface layer and pavement structure in terms of fatigue and permanent deformation with defined traffic and environmental conditions. The asphalt mixes studied were used in a pavement structure as surface layer of 60 mm thickness. The performance of the pavement was compared to the performance of the same pavement structure where different kinds of asphalt concrete were used as surface layer. In comparison to a conventional asphalt concrete, three eco-friendly materials, two warm mix asphalt and a rubberized asphalt concrete, were analyzed. The First Two Chapters summarize the necessary steps aimed to satisfy the sustainable pavement design procedure. In Chapter I the problem of asphalt pavement eco-compatible design was introduced. The low environmental impact materials such as the Warm Mix Asphalt and the Rubberized Asphalt Concrete were described in detail. In addition the value of a rational asphalt pavement design method was discussed. Chapter II underlines the importance of a deep laboratory characterization based on appropriate materials selection and performance evaluation. In Chapter III, CalME is introduced trough a specific explanation of the different equipped design approaches and specifically explaining the I-R procedure. In Chapter IV, the experimental program is presented with a explanation of test laboratory devices adopted. The Fatigue and Rutting performances of the study mixes are shown respectively in Chapter V and VI. Through these laboratory test data the CalME I-R models parameters for Master Curve, fatigue damage and permanent shear strain were evaluated. Lastly, in Chapter VII, the results of the asphalt pavement structures simulations with different surface layers were reported. For each pavement structure, the total surface cracking, the total rutting, the fatigue damage and the rutting depth in each bound layer were analyzed.

Chemical Production and Microelectronic Applications of Graphene and Nano-Graphene Derivatives

Graphene and graphenic derivatives have rapidly emerged as an extremely promising system for electronic, optical, thermal, and electromechanical applications. Several approaches have been developed to produce these materials (i.e. scotch tape, CVD, chemical and solvent exfoliation). In this work we report a chemical approach to produce graphene by reducing graphene oxide (GO) via thermal or electrical methods. A morphological and electrical characterization of these systems has been performed using different techniques such as SPM, SEM, TEM, Raman and XPS. Moreover, we studied the interaction between graphene derivates and organic molecules focusing on the following aspects: - improvement of optical contrast of graphene on different substrates for rapid monolayer identification1 - supramolecular interaction with organic molecules (i.e. thiophene, pyrene etc.)4 - covalent functionalization with optically active molecules2 - preparation and characterization of organic/graphene Field Effect Transistors3-5 Graphene chemistry can potentially allow seamless integration of graphene technology in organic electronics devices to improve device performance and develop new applications for graphene-based materials. [1] E. Treossi, M. Melucci, A. Liscio, M. Gazzano, P. Samorì, and V. Palermo, J. Am. Chem. Soc., 2009, 131, 15576. [2] M. Melucci, E. Treossi, L. Ortolani, G. Giambastiani, V. Morandi, P. Klar, C. Casiraghi, P. Samorì, and V. Palermo, J. Mater. Chem., 2010, 20, 9052. [3] J.M. Mativetsky, E. Treossi, E. Orgiu, M. Melucci, G.P. Veronese, P. Samorì, and V. Palermo, J. Am. Chem. Soc., 2010, 132, 14130. [4] A. Liscio, G.P. Veronese, E. Treossi, F. Suriano, F. Rossella, V. Bellani, R. Rizzoli, P. Samorì and V. Palermo, J. Mater. Chem., 2011, 21, 2924. [5] J.M. Mativetsky, A. Liscio, E. Treossi, E. Orgiu, A. Zanelli, P. Samorì , V. Palermo, J. Am. Chem. Soc., 2011, 133, 14320

Measurement of K(892)*0 resonance production in Pb-Pb collisions with the ALICE experiment at the LHC

The analysis of the K(892)*0 resonance production in Pb–Pb collisions at √sNN = 2.76 TeV with the ALICE detector at the LHC is presented. The analysis is motivated by the interest in the measurement of short-lived resonances production that can provide insights on the properties of the medium produced in heavy-ion collisions both during its partonic (Quark-Gluon Plasma) and hadronic phase. This particular analysis exploits particle identification of the ALICE Time-Of-Flight detector. The ALICE experiment is presented, with focus on the performance of the Time-Of-Flight system. The aspects of calibration and data quality controls are discussed in detail, while illustrating the excellent and very stable performance of the system in different collision environments at the LHC. A full analysis of the K*0 resonance production is presented: from the resonance reconstruction to the determination of the efficiency and the systematic uncertainty. The results show that the analysis strategy discussed is a valid tool to measure the K∗0 up to intermediate momenta. Preliminary results on K*0 resonance production at the LHC are presented and confirmed to be a powerful tool to study the physics of ultra-relativistic heavy-ion collisions.

Ricerca di Escherichia coli produttori di verocitotossine e definizione di obiettivi di performance nella produzione primaria di alimenti di origine animale

La presenza di Escherichia coli produttori di verocitotossine (VTEC o STEC) rappresenta una tra le più importanti cause di malattia alimentare attualmente presenti in Europa. La sua presenza negli allevamenti di animali destinati alla produzione di alimenti rappresenta un importante rischio per la salute del consumatore. In conseguenza di comuni contaminazioni che si realizzano nel corso della macellazione, della mungitura i VTEC possono essere presenti nelle carni e nel latte e rappresentano un grave rischio se la preparazione per il consumo o i processi di lavorazione non comportano trattamenti in grado d’inattivarli (es. carni crude o poco cotte, latte non pastorizzato, formaggi freschi a latte crudo). La contaminazione dei campi coltivati conseguente alla dispersione di letame o attraverso acque contaminate può veicolare questi stipiti che sono normalmente albergati nell’intestino di ruminanti (domestici e selvatici) e anche prodotti vegetali consumati crudi, succhi e perfino sementi sono stati implicati in gravi episodi di malattia con gravi manifestazioni enteriche e complicazioni in grado di causare quadri patologici gravi e anche la morte. Stipiti di VTEC patogeni ingeriti con gli alimenti possono causare sintomi gastroenterici, con diarrea acquosa o emorragica (nel 50% dei casi), crampi addominali, febbre lieve e in una percentuale più bassa nausea e vomito. In alcuni casi (circa 5-10%) l’infezione gastroenterica si complica con manifestazioni tossiemiche caratterizzate da Sindrome Emolitico Uremica (SEU o HUS) con anemia emolitica, insufficienza renale grave e coinvolgimento neurologico o con una porpora trombotica trombocitopenica. Il tasso di mortalità dei pazienti che presentano l’infezione da E. coli è inferiore all’1%. I dati forniti dall’ECDC sulle infezioni alimentari nel periodo 2006-2010 hanno evidenziato un trend in leggero aumento del numero di infezioni a partire dal 2007. L’obiettivo degli studi condotti è quello di valutare la prevalenza ed il comportamento dei VTEC per una analisi del rischio più approfondita.

Production of Z bosons in proton-proton collisions at root out s = 10 TeV: Expectations for early measurements at the ATLAS experiment

The production of the Z boson in proton-proton collisions at the LHC serves as a standard candle at the ATLAS experiment during early data-taking. The decay of the Z into an electron-positron pair gives a clean signature in the detector that allows for calibration and performance studies. The cross-section of ~ 1 nb allows first LHC measurements of parton density functions. In this thesis, simulations of 10 TeV collisions at the ATLAS detector are studied. The challenges for an experimental measurement of the cross-section with an integrated luminositiy of 100 pb−1 are discussed. In preparation for the cross-section determination, the single-electron efficiencies are determined via a simulation based method and in a test of a data-driven ansatz. The two methods show a very good agreement and differ by ~ 3% at most. The ingredients of an inclusive and a differential Z production cross-section measurement at ATLAS are discussed and their possible contributions to systematic uncertainties are presented. For a combined sample of signal and background the expected uncertainty on the inclusive cross-section for an integrated luminosity of 100 pb−1 is determined to 1.5% (stat) +/- 4.2% (syst) +/- 10% (lumi). The possibilities for single-differential cross-section measurements in rapidity and transverse momentum of the Z boson, which are important quantities because of the impact on parton density functions and the capability to check for non-pertubative effects in pQCD, are outlined. The issues of an efficiency correction based on electron efficiencies as function of the electron’s transverse momentum and pseudorapidity are studied. A possible alternative is demonstrated by expanding the two-dimensional efficiencies with the additional dimension of the invariant mass of the two leptons of the Z decay.

Tracking, b-tagging and measurement of the b-jet production cross section with the ATLAS detector

The Standard Model of elementary particle physics was developed to describe the fundamental particles which constitute matter and the interactions between them. The Large Hadron Collider (LHC) at CERN in Geneva was built to solve some of the remaining open questions in the Standard Model and to explore physics beyond it, by colliding two proton beams at world-record centre-of-mass energies. The ATLAS experiment is designed to reconstruct particles and their decay products originating from these collisions. The precise reconstruction of particle trajectories plays an important role in the identification of particle jets which originate from bottom quarks (b-tagging). This thesis describes the step-wise commissioning of the ATLAS track reconstruction and b-tagging software and one of the first measurements of the b-jet production cross section in pp collisions at sqrt(s)=7 TeV with the ATLAS detector. The performance of the track reconstruction software was studied in great detail, first using data from cosmic ray showers and then collisions at sqrt(s)=900 GeV and 7 TeV. The good understanding of the track reconstruction software allowed a very early deployment of the b-tagging algorithms. First studies of these algorithms and the measurement of the b-tagging efficiency in the data are presented. They agree well with predictions from Monte Carlo simulations. The b-jet production cross section was measured with the 2010 dataset recorded by the ATLAS detector, employing muons in jets to estimate the fraction of b-jets. The measurement is in good agreement with the Standard Model predictions.