Coal Combustion Residuals valorisation through the production of compressed masonry brick

The Niger Coal Society (Societé Nigérienne de Charbon – SONICHAR) produces electricity for local consumption in Tefereyre, 75 km north-west from Agadez, Niger. The coal combustion residuals production is about 150,000 tons per year. In order to reduce this environmental burden and to valorize these by-products, a study focusing on their physical and chemical features as well as on the mechanical resistance of compressed brick has been undertaken. Physical characterization of coal slag, chemical and lixiviation tests have been carried out, assessing the material main parameters, verifying the presence of hazardous composites and elements and comparing the obtained results with the findings of an in-deep literary review. Cement powder has been chosen as stabilizing agent as a preliminary option. Four different dosages have been tested and bricks have been produced with a hand-operated press. Compressive strength has been tested at different days of curing. Results show remarkable uniaxial compressive strengths (UCS) for all the mixes after cure, ranging from 4MPa up to more than 20MPa for the highest stabilization ratio. UCS higher than 5MPa have been observed for 20% and 30% cement stabilization ratios after only 7 days of cure, reaching respectively about 11MPa and 13MPa after 45 days. In conclusion obtained bricks show good mechanical resistance and low weight. No health threat has been detected from the obtained sample. Study developments are oriented towards the feasibility of the utilization of low-cost, locally available stabilization means, notably clay and cohesive soils, and on thermal properties assessment.

Taguchi optimisation approach for production of activated carbon from phosphoric acid impregnated palm kernel shell by microwave heating

Taguchi method was applied to investigate the optimal operating conditions in the preparation of activated carbon using palm kernel shell with quadruple control factors: irradiation time, microwave power, concentration of phosphoric acid as impregnation substance and impregnation ratio between acid and palm kernel shell. The best combination of the control factors as obtained by applying Taguchi method was microwave power of 800 W, irradiation time of 17 min, impregnation ratio of 2, and acid concentration of 85%. The noise factor (particle size of raw material) was considered in a separate outer array, which had no effect on the quality of the activated carbon as confirmed by t-test. Activated carbon prepared at optimum combination of control factors had high BET surface area of 1,473.55 m² g-1 and high porosity. The adsorption equilibrium and kinetic data can satisfactorily be described by the Langmuir isotherm and a pseudo-second-order kinetic model, respectively. The maximum adsorbing capacity suggested by the Langmuir model was 1000 mg g-1.

Production of porous aluminium and iron sulphated oxyhydroxides using industrial grade coagulants for optimised arsenic removal from groundwater

The optimisation of Fe and Al oxyhydroxide materials produced using industrial grade coagulants is presented in this work. The effects of synthesis pH and post-synthesis washing procedure onto the arsenic adsorption capacity of the materials were investigated. It was shown that the materials produced at higher pH were more efficient in removing As(V), especially after cleaning procedure. The materials produced at lower pH were less efficient in removing As(V) but the higher presence of sulphate groups in the materials produced at lower pH enhanced As(III) adsorption. Most performing materials can remove up to 84.7 mg As(V) g^-1 or 77.9 mg As(III) g^-1.

Rapid and efficient production of L-lactate from xylose using electrodialysis culture-associated product separation

L-Lactate was produced from xylose using electrodialysis culture (ED-C)-associated product separation. In a medium containing 50 g xylose/l, the ED-C was completed in only 32 h (i.e. less than half the time taken by the control culture, without electrodialysis). At 80 g xylose/l, the control culture was unable to consume more than 50 g xylose/1, whereas the ED-C showed increased xylose consumption and was completed by 45 h. The maximum rate of lactate production in the ED-C was higher than that in the control culture. ED-C was also carried out (at 80 g initial xylose/ l) with a supply of fresh xylose-free medium. This ED-C was completed within 30 h, which represents a reduction in fermentation time of 15 h when compared to ED-C without addition of xylose-free medium. Thus, rapid production of L-lactate was achieved by using ED-C which supplied fresh xylose-free medium.

Understanding the 'production' of the schooling identities of young working class boys: time to move beyond the sociological/psychological divide?

In recent times the sociology of childhood has played an important role in challenging the dominance of Piagetian models of child development in shaping the way we think about children and childhood. What such work has successfully achieved is to increase our understanding of the socially constructed nature of childhood; the social competence and agency of children; and the diverse nature of children’s lives, reflecting the very different social contexts within which they are located. One of the problems that has tended to be associated with this work, however, is that in its critique of developmentalism it has tended simply to replace one orthodoxy (psychology) with another (sociology) rather than providing the opportunity to transcend this divide. The purpose of this paper is to demonstrate some of the potential ways in which the sociological/psychological divide might be transcended and the benefits of this for understanding, more fully, the ‘production’ of children’s schooling identities. In particular it shows how some of the key sociological insights to be found in the work of Bourdieu may be usefully extended by the work inspired by the developmental psychologist, Vygotsky. The key arguments are illustrated by reference to ethnographic data relating to the schooling experiences and identities of a group of 5-6 year old working class boys.

Fermentative production of glycine betaine and trehalose from acid whey using Actinopolyspora halophila (MTCC 263)

Acid whey has become a major concern especially in dairy industry manufacturing Greek yoghurt. Proper disposal of acid whey is essential as it not only increases the BOD of water but also increases the acidity when disposed of in landfill, rendering soil barren and unsuitable for cultivation. Effluent (acid-whey) treatment increases the cost of production. The vast quantities of acid whey that are produced by the dairy industry make the treatment and safe disposal of effluent very difficult. Hence an economical way to handle this problem is very important. Biogenic glycine betaine and trehalose have many applications in food and confectionery industry, medicine, bioprocess industry, agriculture, genetic engineering, and animal feeds (etc.), hence their production is of industrial importance. Here we used the extreme, obligate halophile Actinopolyspora halophila (MTCC 263) for fermentative production of glycine betaine and trehalose from acid whey. Maximum yields were obtained by implementation of a sequential media optimization process, identification and addition of rate-limiting enzyme cofactors via a bioinformatics approach, and manipulation of nitrogen substrate supply. The implications of using glycine as a precursor were also investigated. The core factors that affected production were identified and then optimized using orthogonal array design followed by response surface methodology. The maximum production achieved after complete optimization was 9.07 ± 0.25 g/L and 2.49 ± 0.14 g/L for glycine betaine and trehalose, respectively.

A novel scalable manufacturing process for the production of hydrogel-forming microneedle arrays

A novel manufacturing process for fabricating microneedle arrays (MN) has been designed and evaluated. The prototype is able to successfully produce 14 × 14 MN arrays and is easily capable of scale-up, enabling the transition from laboratory to industry and subsequent commercialisation. The method requires the custom design of metal MN master templates to produce silicone MN moulds using an injection moulding process. The MN arrays produced using this novel method was compared with centrifugation, the traditional method of producing aqueous hydrogel-forming MN arrays. The results proved that there was negligible difference between either methods, with each producing MN arrays with comparable quality. Both types of MN arrays can be successfully inserted in a skin simulant. In both cases the insertion depth was approximately 60% of the needle length and the height reduction after insertion was in both cases approximately 3%.

Novel Supercritical Carbon Dioxide Impregnation Technique for the Production of Amorphous Solid Drug Dispersions: A Comparison to Hot Melt Extrusion

The formulation of BCS Class II drugs as amorphous solid dispersions has been shown to provide advantages with respect to improving the aqueous solubility of these compounds. While hot melt extrusion (HME) and spray drying (SD) are among the most common methods for the production of amorphous solid dispersions (ASDs), the high temperatures often required for HME can restrict the processing of thermally labile drugs, while the use of toxic organic solvents during SD can impact on end-product toxicity. In this study, we investigated the potential of supercritical fluid impregnation (SFI) using carbon dioxide as an alternative process for ASD production of a model poorly water-soluble drug, indomethacin (INM). In doing so, we produced ASDs without the use of organic solvents and at temperatures considerably lower than those required for HME. Previous studies have concentrated on the characterization of ASDs produced using HME or SFI but have not considered both processes together. Dispersions were manufactured using two different polymers, Soluplus and polyvinylpyrrolidone K15 using both SFI and HME and characterized for drug morphology, homogeneity, presence of drug-polymer interactions, glass transition temperature, amorphous stability of the drug within the formulation, and nonsink drug release to measure the ability of each formulation to create a supersaturated drug solution. Fully amorphous dispersions were successfully produced at 50% w/w drug loading using HME and 30% w/w drug loading using SFI. For both polymers, formulations containing 50% w/w INM, manufactured via SFI, contained the drug in the γ-crystalline form. Interestingly, there were lower levels of crystallinity in PVP dispersions relative to SOL. FTIR was used to probe for the presence of drug-polymer interactions within both polymer systems. For PVP systems, the nature of these interactions depended upon processing method; however, for Soluplus formulations this was not the case. The area under the dissolution curve (AUC) was used as a measure of the time during which a supersaturated concentration could be maintained, and for all systems, SFI formulations performed better than similar HME formulations.

Toxic interactions of metal ions (Cd2+, Pb2+, Zn2+ and Sb3- on in vitro biomass production of ectomycorrhizal fungi

A number of ectomycorrhizal (ECM) fungi, from sites uncontaminated by toxic metals, were investigated to determine their sensitivity to Cd^2-, Pb²⁺, Zn²⁺ and Sb^3-, measured as an inhibition of fungal biomass production. Isolates were grown in liquid media amended with the metals, individually (over a range of concentrations) and in combination (at single concentrations) to determine any significant interactions between the metals. Significant interspecific variation in sensitivity to Cd²⁺ and Zn²⁺ was recorded, while Pb²⁺ and Sb^3- individually had little effect. The presence of Pb²⁺ and Sb^3- in the media did however, ameliorate Cd²⁺ and Zn²⁺ toxicity in some circumstances. Interactions between Cd²⁺ and Zn²⁺ were investigated further over a range of concentrations. Zn²⁺ was found to significantly ameliorate the toxicity of Cd²⁺ to three of the four isolates tested. The influence of Zn²⁺ varied between ECM species and with the concentrations of metals tested.

Using Flory-Huggins phase diagrams as a pre-formulation tool for the production of amorphous solid dispersions; a comparison between hot-melt extrusion and spray drying

Objectives: Amorphous drug forms provide a useful method of enhancing the dissolution performance of poorly water-soluble drugs; however, they are inherently unstable. In this article, we have used Flory–Huggins theory to predict drug solubility and miscibility in polymer candidates, and used this information to compare spray drying and melt extrusion as processes to manufacture solid dispersions.
Method:  Solid dispersions were characterised using a combination of thermal (thermogravimetric analysis and differential scanning calorimetry) and spectroscopic (Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction methods. 
Key Findings: Spray drying permitted generation of amorphous solid dispersions to be produced across a wider drug concentration than melt extrusion. Melt extrusion provided sufficient energy for more intimate mixing to be achieved between drug and polymer, which may improve physical stability. It was also confirmed that stronger drug–polymer interactions might be generated through melt extrusion. Remixing and dissolution of recrystallised felodipine into the polymeric matrices did occur during the modulated differential scanning calorimetry analysis, but the complementary information provided from FTIR confirms that all freshly prepared spray-dried samples were amorphous with the existence of amorphous drug domains within high drug-loaded samples. 
Conclusion: Using temperature–composition phase diagrams to probe the relevance of temperature and drug composition in specific polymer candidates facilitates polymer screening for the purpose of formulating solid dispersions.

Production of ultracold hydrogen and deuterium via Doppler-cooled Feshbach molecules

A counterintuitive scheme to produce ultracold hydrogen via fragmentation of laser cooled diatomic hydrides is presented where the final atomic H temperature is inversely proportional to the mass of the molecular parent. In addition, the critical density for formation of a Bose-Einstein condensate (BEC) at a fixed temperature is reduced by a factor (mH/mMH)3/2 over directly cooled hydrogen atoms. The narrow Feshbach resonances between a S01 atom and hydrogen are well suited to a tiny center of mass energy release necessary during fragmentation. With the support of ab initio quantum chemistry, it is demonstrated that BaH is an ideal diatomic precursor that can be laser cooled to a Doppler temperature of ∼26μK with just two rovibronic transitions, the simplest molecular cooling scheme identified to date. Preparation of a hydrogen atom gas below the critical BEC temperature Tc is feasible with present cooling technology, with optical pulse control of the condensation process.