Gridded bathymetry from multibeam echosounder EM122 data of the cruise MSM34/2 (2013)

Bathymetry based on data recorded during MSM34-2 between 27.12.2013 and 18.01.2014 in the Black Sea. The main objective of this cruise was the mapping and imaging of the gas hydrate distribution and gas accumulations as well as possible gas migration pathways. Objectives of Cruise: Gas hydrates have been the focus of scientific and economic interest for the past 15-20 years, mainly because the amount of carbon stored in gas hydrates is much greater than in other carbon reservoirs. Several countries including Japan, Korea and India have launched vast reasearch programmes dedicated to the exploration for gas hydrate resources and ultimately the exploitation of the gas hydrates for methane. The German SUGAR project that is financed the the Ministry of Education and Research (BmBF) and the Ministry of Economics (BmWi) aims at developing technology to exploit gas hydrate resources by injecting and storing CO2 instead of methane in the hydrates. This approach includes techniques to locate and quantify hydrate reservoirs, drill into the reservoir, extract methane from the hydrates by replacing it with CO2, and monitor the thus formed CO2-hydrate reservoir. Numerical modeling has shown that any exploitation of the gas hydrates can only be succesful, if sufficient hydrate resources are present within permeable reservoirs such as sandy or gravelly deposits. The ultimate goal of the SUGAR project being a field test of the technology developed within the project, knowledge of a suitable test site becomes crucial. Within European waters only the Norwegian margin and the Danube deep-sea fan show clear geophysical evidence for large gas hydrate accumulations, but only the Danube deep-sea fan most likely contains gas hydrates within sandy deposits. The main objective of cruise MSM34 therefore is locating and characterising suitable gas hydrate deposits on the Danube deep-sea fan.

Dissolved organic matter composition derived from FT-ICR-MS analyses during HEINCKE cruise HE361

Dissolved organic matter (DOM) is the main substrate and energy source for heterotrophic bacterioplankton. To understand the interactions between DOM and the bacterial community (BC), it is important to identify the key factors on both sides in detail, chemically distinct moieties in DOM and the various bacterial taxa. Next-generation sequencing facilitates the classification of millions of reads of environmental DNA and RNA amplicons and ultrahigh-resolution mass spectrometry yields up to 10,000 DOM molecular formulae in a marine water sample. Linking this detailed biological and chemical information is a crucial first step toward a mechanistic understanding of the role of microorganisms in the marine carbon cycle. In this study, we interpreted the complex microbiological and molecular information via a novel combination of multivariate statistics. We were able to reveal distinct relationships between the key factors of organic matter cycling along a latitudinal transect across the North Sea. Total BC and DOM composition were mainly driven by mixing of distinct water masses and presumably retain their respective terrigenous imprint on similar timescales on their way through the North Sea. The active microbial community, however, was rather influenced by local events and correlated with specific DOM molecular formulae indicative of compounds that are easily degradable. These trends were most pronounced on the highest resolved level, that is, operationally defined 'species', reflecting the functional diversity of microorganisms at high taxonomic resolution.

Gridded bathymetry from multibeam echosounder EM122 data of the cruise MSM34/1 (2013)

Bathymetry based on data recorded during MSM34-1 between 09.12.2013 and 27.12.2013 in the Black Sea. The main objective of this cruise was the localization and characterization of suitable gas hydrate deposits on the Danube deep-sea fan.

Comparison of CO2 From Coal Capture Processes and Valorisation Technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorising CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorise captured CO2. Valorising captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2 capture and valorising will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Comparison of CO2 from coal captureprocesses and valorisation technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorizing CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorizecaptured CO2. Valorizing captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2capture and valorizing will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Utilización del cultivo plurianual de pataca (Helianthus tuberosus L.) para la producción de hidratos de carbono fermentables a partir de los tallos

La pataca (Helianthus tuberosus L.) es una especie de cultivo con un alto potencial en la producción de hidratos de carbono de reserva en forma de polifructanos, especialmente inulina, que se acumulan temporalmente en los tallos en forma de polisacáridos para translocarse posteriormente a los tubérculos, donde son almacenados. Aunque tradicionalmente el producto de interés del cultivo son los tubérculos, que acumulan gran cantidad de hidratos de carbono fermentables (HCF) cuando se recogen al final del ciclo de desarrollo, en este trabajo se pretende evaluar el potencial de la pataca como productor de HCF a partir de los tallos cosechados en el momento de máximo contenido en HCF, mediante un sistema de cultivo plurianual. Se han realizado los siguientes estudios: i) Determinación del momento óptimo de cosecha en ensayos con 12 clones ii) Potencial del cultivo plurianual de la pataca en términos de producción anual de biomasa aérea y de HCF en cosechas sucesivas, iii) Ensayos de conservación de la biomasa aérea, iv) Estimación de los costes de las dos modalidades de cultivo de pataca para producción de HCF y v) Estimación de la sostenibilidad energética de la producción de bioetanol mediante la utilización de los subproductos. Para la determinación del momento óptimo de la cosecha de la biomasa aérea se ensayaron 12 clones de diferente precocidad en Madrid; 4 tempranos (Huertos de Moya, C-17, Columbia y D-19) y 8 tardíos (Boniches, China, K-8, Salmantina, Nahodka, C-13, INIA y Violeta de Rennes). El máximo contenido en HCF tuvo lugar en el estado fenológico de botón floral-flor que además coincidió con la máxima producción de biomasa aérea. De acuerdo con los resultados obtenidos, la cosecha de los clones tempranos se debería realizar en el mes de julio y en los clones tardíos en septiembre, siendo éstos últimos más productivos. La producción media más representativa entre los 12 clones, obtenida en el estado fenológico de botón floral fue de 23,40 t ms/ha (clon INIA), con un contenido medio en HCF de 30,30 % lo que supondría una producción potencial media de 7,06 t HCF/ha. La producción máxima en HCF se obtuvo en el clon Boniches con 7,61 t/ha y 22,81 t ms/ha de biomasa aérea. En el sistema de cultivo plurianual la cantidad de tallos por unidad de superficie aumenta cada año debido a la cantidad de tubérculos que van quedando en el terreno, sobre todo a partir del 3er año, lo que produce la disminución del peso unitario de los tallos, con el consiguiente riesgo de encamado. El aclareo de los tallos nacidos a principios de primavera mediante herbicidas tipo Glifosato o mediante una labor de rotocultor rebaja la densidad final de tallos y mejora los rendimientos del cultivo. En las experiencias de conservación de la biomasa aérea se obtuvo una buena conservación por un período de 6 meses de los HCF contenidos en los tallos secos empacados y almacenados bajo cubierta. Considerando que el rendimiento práctico de la fermentación alcohólica es de 0,5 l de etanol por cada kg de azúcar, la producción potencial de etanol para una cosecha de tallos de 7,06 t de HCF/ha sería de 3.530 l/ha. El bagazo producido en la extracción de los HCF de la biomasa aérea supondría 11,91 t/ha lo que utilizado para fines térmicos supone más de 3 veces la energía primaria requerida en el proceso de producción de etanol, considerando un poder calorífico inferior de 3.832,6 kcal/kg. Para una producción de HCF a partir de la biomasa aérea de 7,06 t/ha y en tubérculos al final del ciclo de 12,11 t/ha, los costes de producción estimados para cada uno de ellos fueron de 184,69 €/t para los HCF procedentes de la biomasa aérea y 311,30 €/t para los de tubérculos. Como resultado de este trabajo se puede concluir que la producción de HCF a partir de la biomasa aérea de pataca en cultivo plurianual, es viable desde un punto de vista técnico, con reducción de los costes de producción respecto al sistema tradicional de cosecha de tubérculos. Entre las ventajas técnicas de esta modalidad de cultivo, cabe destacar: la reducción de operaciones de cultivo, la facilidad y menor coste de la cosecha, y la posibilidad de conservación de los HCF en la biomasa cosechada sin mermas durante varios meses. Estas ventajas, compensan con creces el menor rendimiento por unidad de superficie que se obtiene con este sistema de cultivo frente al de cosecha de los tubérculos. Jerusalem artichoke (Helianthus tuberosus L.) (JA) is a crop with a high potential for the production of carbohydrates in the form of polyfructans, especially inulin, which are temporarily accumulated in the stems in the form of polysaccharides. Subsequently they are translocated to the tubers, where they are finally accumulated. In this work the potential of Jerusalem artichoke for fermentable carbohydrates from stems that are harvested at their peak of carbohydrates accumulation is assessed as compared to the traditional cultivation system that aims at the production of tubers harvested at the end of the growth cycle. Tubers are storage organs of polyfructans, namely fermentable carbohydrates. Studies addressed in this work were: i) Determination of the optimum period of time for stem harvesting as a function of clone precocity in a 12-clone field experiment; ii) Study of the potential of JA poly-annual crop regarding the annual yield of aerial biomass and fermentable carbohydrates (HCF) over the years; iii) Tests of storage of the aerial biomass, iv) Comparative analysis of the two JA cultivation systems for HCF production: the poly-annual system for aerial biomass harvesting versus the annual cultivation system for tubers and v) Estimation of the energy sustainability of the bioethanol production by using by-products of the production chain. In order to determine the best period of time for aerial biomass harvesting twelve JA clones of different precocity were tested in Madrid: four early clones (Huertos de Moya, C-17, Columbia and D-19) and eight late clones (Boniches, China, K-8 , Salmantina, Nahodka, C-13, INIA and Violeta de Rennes). Best time was between the phenological stages of floral buds (closed capitula) and blossom (opened capitula), period in which the peak of biomass production coincides with the peak of HCF accumulation in the stems. According to the results, the early clones should be harvested in July and the late ones in September, being the late clones more productive. The clone named INIA was the one that exhibited more steady yields in biomass over the 12 clones experimented. The average potential biomass production of this clone was 23.40 t dm/ha when harvested at the floral buds phenological stage; mean HCF content is 30.30%, representing 7.06 t HCF/ha yield. However, the highest HCF production was obtained for the clone Boniches, 7.61 t HCF/ha from a production of 22.81 t aerial biomass/ha. In the poly-annual cultivation system the number of stems per unit area increases over the years due to the increase in the number of tubers that are left under ground; this effect is particularly important after the 3rd year of the poly-annual crop and results in a decrease of the stems unit weight and a risk of lodging. Thinning of JA shoots in early spring, by means of an herbicide treatment based on glyphosate or by means of one pass with a rotary tiller, results in a decrease of the crop stem density and in higher crop yields. Tests of biomass storing showed that the method of keeping dried stems packed and stored under cover results in a good preservation of HCF for a period of six months at least. Assuming that the fermentation yield is 0.5 L ethanol per kg sugars and a HCF stem production of 7.06 t HCF/ha, the potential for bioethanol is estimated at 3530 L/ha. The use of bagasse -by-product of the process of HCF extraction from the JA stems- for thermal purposes would represent over 3 times the primary energy required for the industrial ethanol production process, assuming 11.91 t/ha bagasse and 3832.6 kcal/kg heating value. HCF production costs of 7.06 t HCF/ha yield from aerial biomass and HCF production costs of 12.11 t HCF/ha from tubers were estimated at 184.69 €/t HCF and 311.30 €/t HCF, respectively. It can be concluded that the production of HCF from JA stems, following a poly-annual cultivation system, can be feasible from a technical standpoint and lead to lower production costs as compared to the traditional annual cultivation system for the production of HCF from tubers. Among the technical advantages of the poly-annual cultivation system it is worth mentioning the reduction in crop operations, the ease and efficiency of harvesting operations and the possibility of HCF preservation without incurring in HCF losses during the storage period, which can last several months. These advantages might compensate the lower yield of HCF per unit area that is obtained in the poly-annual crop system, which aims at stems harvesting, versus the annual one, which involves tubers harvesting.

Pre-Feasibility Study of Hybrid Wind Power-H-2 System Connected to Electrical Grid

The growth of wind power as an electric energy source is profitable from an environmental point of view and improves the energetic independence of countries with little fossil fuel resources. However, the wind resource randomness poses a great challenge in the management of electric grids. This study raises the possibility of using hydrogen as a mean to damp the variability of the wind resource. Thus, it is proposed the use of all the energy produced by a typical wind farm for hydrogen generation, that will in turn be used after for suitable generation of electric energy according to the operation rules in a liberalized electric market.

Dual role of HupF in the biosynthesis of [NiFe] hydrogenase in Rhizobium leguminosarum

Background: [NiFe] hydrogenases are enzymes that catalyze the oxidation of hydrogen into protons and electrons, to use H2 as energy source, or the production of hydrogen through proton reduction, as an escape valve for the excess of reduction equivalents in anaerobic metabolism. Biosynthesis of [NiFe] hydrogenases is a complex process that occurs in the cytoplasm, where a number of auxiliary proteins are required to synthesize and insert the metal cofactors into the enzyme structural units. The endosymbiotic bacterium Rhizobium leguminosarum requires the products of eighteen genes (hupSLCDEFGHIJKhypABFCDEX) to synthesize an active hydrogenase. hupF and hupK genes are found only in hydrogenase clusters from bacteria expressing hydrogenase in the presence of oxygen. Results: HupF is a HypC paralogue with a similar predicted structure, except for the C-terminal domain present only in HupF. Deletion of hupF results in the inability to process the hydrogenase large subunit HupL, and also in reduced stability of this subunit when cells are exposed to high oxygen tensions. A ?hupF mutant was fully complemented for hydrogenase activity by a C-terminal deletion derivative under symbiotic, ultra low-oxygen tensions, but only partial complementation was observed in free living cells under higher oxygen tensions (1% or 3%). Co-purification experiments using StrepTag-labelled HupF derivatives and mass spectrometry analysis indicate the existence of a major complex involving HupL and HupF, and a less abundant HupF-HupK complex. Conclusions: The results indicate that HupF has a dual role during hydrogenase biosynthesis: it is required for hydrogenase large subunit processing and it also acts as a chaperone to stabilize HupL when hydrogenase is synthesized in the presence of oxygen.

Parque eólico Cassino

La energía eólica, así como otras energías renovables, ha experimentado en la última década un gran auge que va extendiéndose alrededor de todo el mundo, cada vez más concienciado de la importancia de las energías renovables como una fuente alternativa de energía. Se han sumado al reto todos los países acogidos al Protocolo de Kyoto, que a fin de reducir emisiones están potenciando la energía eólica como la fuente de energía renovable hoy día más viable para la generación eléctrica. Brasil alcanzó en 2011 los 1.509 MW instalados, lo que representa el 50% de Latinoamérica, seguido por México con el 31%. Las características del sector eléctrico así como un marco legal favorable y el alto potencial eólico, hacen que la perspectiva de crecimiento en este tipo de energía sea muy favorable durante los próximos años, con estimaciones de unos 20.000 MW para 2020. El asentamiento del sector en el país de algunos de los fabricantes más importantes y los avances en cuanto a eficiencia de los aerogeneradores, mayor aprovechamiento de la energía de los vientos menos intensos, amplía las posibles ubicaciones de parques eólicos permitiendo una expansión grande del sector. El parque eólico objeto del proyecto está ubicado en el estado de Rio Grande do Sul, al sur del país, y está constituido por 33 aerogeneradores de 2,0 MW de potencia unitaria, lo que supone una potencia total instalada de 66 MW. La energía eléctrica generada en él será de 272,8 GWh/año. Esta energía se venderá mediante un contrato de compraventa de energía (PPA, Power Purchase Agreement) adjudicado por el gobierno Brasileño en sus sistemas de subasta de energía. En el proyecto se aborda primeramente la selección del emplazamiento del parque eólico a partir de datos de viento de la zona. Estos datos son estudiados para evaluar el potencial eólico y así poder optimizar la ubicación de las turbinas eólicas. Posteriormente se evalúan varios tipos de aerogeneradores para su implantación en el emplazamiento. La elección se realiza teniendo en cuenta las características técnicas de las máquinas y mediante un estudio de la productividad del parque con el aerogenerador correspondiente. Finalmente se opta por el aerogenerador G97-2.0 de GAMESA. La ejecución técnica del parque eólico se realiza de forma que se minimicen los impactos ambientales y de acuerdo a lo establecido en el Estudio de Impacto Ambiental realizado. Este proyecto requiere una inversión de 75,4 M€, financiada externamente en un 80 % y el 20 % con recursos propios del promotor. Del estudio económico-financiero se deduce que el proyecto diseñado es rentable económicamente y viable, tanto desde el punto de vista técnico como financiero. Abstract Wind energy, as well as other renewable energies, has experienced over the last decade a boom that is spreading around the world increasingly aware of the importance of renewable energy as an alternative energy source. All countries that ratified the Kyoto Protocol have joined the challenge promoting wind energy in order to reduce emissions as the more feasible renewable energy for power generation. In 2011 Brazil reached 1509 MW installed, 50% of Latin America, followed by Mexico with 31%. Electric sector characteristics as well as a favorable legal framework and the high wind potential, make the perspective of growth in this kind of energy very positive in the coming years, with estimates of about 20,000 MW by 2020. Some leading manufacturers have settled in the country and improvements in wind turbines efficiency with less intense winds, make higher the number of possible locations for wind farms allowing a major expansion of the sector. The planned wind farm is located in the state of Rio Grande do Sul, in the south of the Brazil, and is made up of 33 wind turbines of 2,0 MW each, representing a total capacity of 66 MW. The electricity generated, 272,8 GWh/year will be sold through a power purchase agreement (PPA) awarded by the Brazilian government in its energy auction systems. The project deals with the site selection of the wind farm from wind data in the area. These data are studied to evaluate the wind potential and thus optimize the location of wind turbines. Then several types of turbines are evaluated for implementation at the site. The choice is made taking into account the technical characteristics of the machines and a study of the productivity of the park with the corresponding turbine. Finally selected wind turbine is Gamesa G97-2.0. The technical implementation of the wind farm is done to minimize environmental impacts as established in the Environmental Impact Study. This project requires an investment of 75,4 M€, financed externally by 80% and 20% with equity from the promoter. The economic-financial study shows that the project is economically viable, both technically and financially.

Compatibilidad de materiales con las mezclas de bioqueroseno de coco, babasú y palmiste con queroseno comercial

Actualmente existe un gran interés por ampliar las fuentes de energías alternativas para aviación y conseguir con ello una reducción de la huella de carbono y de la fuerte dependencia energética de los combustibles fósiles en diferentes países. Por ello, se están llevando a cabo muchos estudios de investigación que tienen por objetivo la conversión de la materia prima vegetal o biomasa en una nueva fuente de energía. Sin embargo, la sustitución exitosa de los combustibles derivados del petróleo por biocombustibles, requiere el cumplimiento de unos requisitos estrictos, y unas propiedades adecuadas. Este proyecto estudia la compatibilidad de materiales con las mezclas de bioqueroseno de coco (CBK20), babasú (BBK20) y palmiste (PBK20), con queroseno comercial Jet A-1 (K-2). Los materiales estudiados son poliméricos, metálicos y composites de aviación que forman parte del sistema combustible del avión. Este estudio pretende demostrar que tanto los materiales utilizados, como los combustibles investigados, son compatibles cuando se encuentran en contacto a cierta temperatura. Para ello, se han comparado sus propiedades siguiendo las normas de referencia establecidas. ABSTRACT Currently there is a strong interest to expand alternative energy sources for aviation and thereby achieve a reduction in carbon footprint and the strong energy dependence on fossil fuels in different countries. It is therefore being carried out many researches based on the conversion of vegetable feedstock in a new energy source. However, a successful replacement of petroleum fuels with biofuels, requires compliance with strict requirements and suitable properties. This project studies the materials compatibility with blends of coconut (CBK20), babassu (BBK20) and palm kernel (PBK20) biokerosene with commercial aviation jet fuel Jet A-1 (K-2). Polymeric and elastomeric materials, metals and aviation composites has been studied as part of the aircraft fuel system. The objective of this study is to demonstrate that both, the tested materials and the fuels investigated, are compatible when they are in contact at a certain temperature. For this reason, materials and kerosene properties have been compared using the standard test methods

Design of a solar incubator. Part 1: Monitoring temperature and enthalpy gradients under commercial production

The real increase in energy prices and the intention of reducing pollutant emissions in developed countries makes interesting to use solar energy in all the processes where its application is possible. As it is demonstrated in countries sited at latitudes with optimal conditions of solar radiation and temperature, it is possible to use solar energy as heat source for small-scale hatchery [1,2], but beyond, making a design for proper installation; it is possible to use solar energy as main or support energy source in medium and large size incubators . Monitoring of a normal actual process using temperature and relative humidity sensors is necessary to know the actual operating conditions that the solar heating system must be designed and sized for. Moreover, the identification and analysis of temperature and enthalpy gradients inside the incubator is of major importance.

Modelo dinámico y mejora de la recuperación de los hidrocarburos en el Reservorio "QUA IBOE ESTE" del Campo Zafiro

El petróleo en Guinea Ecuatorial como en todo el mundo, es una fuente de energía agotable, pero de mucha importancia por la infinidad de usos de sus derivados. Por eso se necesita optimizar al máximo su producción de los yacimientos. En este proyecto se pretende descubrir qué parámetros variar en el yacimiento “QUA IBOE ESTE” del Campo Zafiro (Guinea Ecuatorial), con el fin de producir más crudo del inicialmente previsto. Para ello emplearemos el método de simulación, usando las herramientas que nos ofrecen los programas de simulación de yacimientos PETREL 2011.2 y ECLIPSE 100. Después de conocer cuántos barriles de petróleo, y metros cúbico de gas recuperaríamos de más, en el apartado económico, se busca conocer el total de beneficio se obtendría. ABSTRACT Oil in Equatorial Guinea and around the world, is an exhaustible energy source, but of great importance for the myriad uses of derivatives. We therefore need to optimize reservoir production. In this project we intend to discover which parameters vary in the field "QUA IBOE ESTE" Zafiro Field (Equatorial Guinea), in order to produce more oil than estimated. To do this we use the simulation method, using the tools that we provide the reservoir simulation programs Petrel 2011.2 and ECLIPSE 100. After knowing how many barrels of oil and cubic meters of gas would recover more in the economic section, we seek to know the total benefit would be obtained.

Flammability properties of dry sewage sludges

Dry sewage sludge are being considered as a possible energy source for direct firing. They have interesting properties to be used as an alternative fuel, but also other characteristics must be considered from the point of view of its safe operation: the most important are ignition sensitivity, explosion severity, thermal sensitivity and thermal stability. The aim of this study was to determine if sewage sludge have different characteristics due to different locations or seasons and how this influences their flammability properties. To study these characteristics sludge samples were selected from different locations in Spain, taken during different seasons. In addition, relationships between flammability parameters and chemical analysis were observed. Some parameters can be controlled during normal operation, such as granulometry or humidity, and may mean a decrease in the risk of explosion. Those relationships are well known for other dusts materials, like coal, but not yet for sewage sludge dusts. Finally, properties related to spontaneous combustion were determined (thermal susceptibility and stability). The addition of those properties to the study provides an overview of the thermal behavior of sewage sludge during their utilization, including transport and storage.

Extracción de energía del agua mediante generadores piezoeléctricos

El desarrollo del Proyecto consiste, por una parte, en el estudio sobre la respuesta de los materiales piezoeléctricos como generadores de energía en un entorno acuoso que está sometido a variaciones de potencial y, por otra, en el estudio técnico y económico de un equipo basado en la utilización esta fuente de energía y su comercialización en el mercado energético. Esta energía es la que se obtiene de la fuerza de arrastre del agua al desplazarse a causa del movimiento ondulatorio de las olas y que el elemento al flexionar es capaz de transformar. El proyecto contempla a partir de modelos, el funcionamiento eléctrico y mecánico de un generador piezoeléctrico, el sistema de electrónica necesaria para su inserción optimizada en la red eléctrica. A partir de esto se desarrolla una instalación que puede adaptarse a los requerimientos del estudio previo. Empleando un modelo de relación técnica y económica se establece una conexión entre estas dos secciones para hacerse una idea de la rentabilidad económica de un equipo de este estilo a día de hoy. El propósito final, es el de estudiar un nuevo tipo de energía, y comenzar una línea que puede llevar a un lugar muy interesante del sector energético. ABSTRACT This Project presents an analysis on the performance of piezoelectric materials as energy producer in an aquatic environment subject to potential variations. Additionally, the Project contains a technical and an economic analysis on the equipment based on the use of this energy source, as well as its commercialization. Energy is obtained by the water drag force when it is moved by the wave’s movement and by its transformation by the piezoelectric material. The Project studies the electric and mechanic functioning of a piezoelectric generator and the necessary electronic system for its optimized insertion on the electricity distribution network. Based on this, it is developed a system that can be adapted to the previous study requirements. The use of a technical and economic relation model allows the establishment of a connection among them in order to estimate the economic profitability of such equipment nowadays. The final objective of this Project is analyzing a new source of energy, which could start a new investigation line that may lead the energetic sector to a very interesting future.

Marine Practice Guidelines for Fuel Cell Applications

This paper focuses on the implementation of fuel cells in marine systems as a propulsion system and energy source. The objective is to provide an overview of the pertinent legislation for marine applications of fuel cells. This work includes a characterization of some guidelines for the safe application of fuel cell systems on ships. It also describes two ships that have implemented fuel cells to obtain energy, the Viking Lady, the first marine ship to include this technology, and Greentug, a reference for new tugs