Microstructure and high cycle fatigue fracture surface of a Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy

Because of the requirements for the damage tolerance and fatigue life of commercial aircraft components, the high cycle fatigue (HCF) properties of Ti–5Al–5Mo–5V–1Cr–1Fe titanium alloy forgings are important. The effects of microstructure types of the α+β titanium alloy on fatigue properties need to be understood. In this paper, by analysing the fracture surfaces of the titanium alloy having four types of microstructure, the effects of microstructure are investigated. The differences of initiation areas and crack propagation among different microstructures were studied. It was found that the area of the initiation region decreases in the order of coarse basketweave, fine basketweave, Widmanstätten, and bimodal microstructure.

Stress and Strain Distributions During Compressive Deformation of Titanium Alloy Affected by Microstructure

In the research of the microstructural influence on dynamic compression, an assumption that the α and the β phases in titanium alloys were linearly strengthened was proposed, and a two-dimensional model using ANSYS (ANSYS, Inc., Canonsburg, PA) focusing on the role of microgeometrical structure was developed. By comparing the stress and strain distributions of different microstructures, the roles of cracks and phase boundaries in titanium compression were studied.

Microstructure and Mechanical Propertiesof a Nitride-Strengthened Reduced ActivationFerritic/Martensitic Steel

Nitride-strengthened reduced activation ferritic/martensitic (RAFM) steels are developed taking advantage of the high thermal stability of nitrides. In the current study, the microstructure and mechanical properties of a nitride-strengthened RAFM steel with improved composition were investigated. Fully martensitic microstructure with fine nitrides dispersion was achieved in the steel. In all, 1.4 pct Mn is sufficient to suppress delta ferrite and assure the steel of the full martensitic microstructure. Compared to Eurofer97, the steel showed similar strength at room temperature but higher strength at 873 K (600 °C). The steel exhibited very high impact toughness and a low ductile-to-brittle transition temperature (DBTT) of 243 K (–30 °C), which could be further reduced by purification.

Characterisation of phase composition, microstructure and microhardness of electroless nickel composite coating co-deposited with SiC on casting aluminium LM24 alloy substrate

Electroless Ni-P (EN) and composite Ni-P-SiC (ENC) coatings were developed on cast aluminium alloy, LM24. The coating phase composition, microstructure and microhardness were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and microhardness tester, respectively, on as-plated and heat-treated specimens. The original microstructure of the Ni-P matrix is not affected by the inclusion of the hard particles SiC. No formation of Ni-Si phase was observed upto 500°C of heat treatment. The microhardness is increased on incorporation of SiC in Ni-P matrix. The hardening mechanism is the formation of intermetallic phase Ni3P on annealing at elevated temperature. Overall, the composite coating (ENC) was found to be superior as compared to particles free (EN) coating in both as-deposited and heat-treated conditions.

Microstructure design of Titanate-based electroceramics

Electrocerâmicos são uma classe de materiais avançados com propriedades eléctricas valiosas para aplicações. Estas propriedades são geralmente muito dependentes da microestrutura dos materiais. Portanto, o objectivo geral deste trabalho é investigar o desenho da resposta dieléctrica de filmes espessos obtidos por Deposição Electroforética (EPD) e cerâmicos monolíticos, através do controlo da evolução da microestrutura durante a sinterização de electrocerâmicos à base de titanatos. Aplicações sem fios na indústria microelectrónica e de comunicações, em rápido crescimento, tornaram-se um importante mercado para os fabricantes de semicondutores. Devido à constante necessidade de miniaturização, redução de custos e maior funcionalidade e integração, a tecnologia de filmes espessos está a tornar-se uma abordagem de processamento de materiais funcionais cada vez mais importante. Uma técnica adequada neste contexto é EPD. Os filmes espessos resultantes necessitam de um passo subsequente de sinterização que é afectada pelo substrato subjacente, tendo este um forte efeito sobre a evolução da microestrutura. Relacionado com a miniaturização e a discriminação do sinal, materiais dieléctricos usados como componentes operando a frequências das microondas em aplicações na industria microelectrónica de comunicações devem apresentar baixas perdas dieléctricas e elevadas permitividade dieléctrica e estabilidade com a temperatura. Materiais do sistema BaO-Ln2O3- TiO2 (BLnT: Ln = La ou Nd), como BaLa4Ti4O15 (BLT) e Ba4.5Nd9Ti18O54 (BNT), cumprem esses requisitos e são interessantes para aplicações, por exemplo, em estações de base para comunicações móveis ou em ressonadores para telefones móveis, onde a miniaturização dos dispositivos é muito importante. Por sua vez, o titanato de estrôncio (SrTiO3, STO) é um ferroeléctrico incipiente com constante dieléctrica elevada e baixas perdas, que encontra aplicação em, por exemplo, condensadores de camada interna, tirando partido de fronteiras de grão altamente resistivas. A dependência da permitividade dieléctrica do campo eléctrico aplicado torna este material muito interessante para aplicações em dispositivos de microondas sintonizáveis. Materiais à base de STO são também interessantes para aplicações termoeléctricas, que podem contribuir para a redução da actual dependência de combustíveis fósseis por meio da geração de energia a partir de calor desaproveitado. No entanto, as mesmas fronteiras de grão resistivas são um obstáculo relativamente à eficiência do STO para aplicações termoeléctricas. Para além do efeito do substrato durante a sinterização constrangida, outros factores, como a presença de fase líquida, a não-estequiometria ou a temperatura de sinterização, afectam significativamente não apenas a microestrutura dos materiais funcionais, mas também a sua resposta dieléctrica. Se adequadamente compreendidos, estes factores podem ser intencionalmente usados para desenhar a microestrutura dos electrocerâmicos e, desta forma, as suas propriedades dieléctricas. O efeito da não-estequiometria (razão Sr/Ti 0.995-1.02) no crescimento de grão e resposta dieléctrica de cerâmicos de STO foi investigado neste trabalho. A mobilidade das fronteiras de grão aumenta com a diminuição da razão Sr/Ti. A resistividade do interior dos grãos e das fronteiras de grão é sistematicamente diminuída em amostras não-estequiométricas de STO, em comparação com o material estequiométrico. O efeito é muito mais forte para as fronteiras de grão do que para o seu interior. Dependências sistemáticas da não-estequiometria foram também observadas relativamente à dependência da condutividade da temperatura (muito mais afectada no caso da contribuição das fronteiras de grão), à capacitância do interior e fronteiras de grão e à espessura das fronteiras de grão. Uma anomalia no crescimento de grão em cerâmicos de STO ricos em Ti foi também observada e sistematicamente analisada. Foram detectadas três descontinuidades na dependência do tipo Arrhenius do crescimento de grão relativamente à temperatura com diminuições no tamanho de grão a temperaturas em torno de 1500, 1550 e 1605 °C. Além disso, descontinuidades semelhantes foram também observadas na dependência da energia de activação relativamente à condutividade das fronteiras de grão e na espessura das fronteiras de grão, avaliadas por Espectroscopia de Impedância. Estas notáveis coincidências suportam fortemente a formação de diferentes complexos de fronteira de grão com transições entre os regimes de crescimento de grão observados, que podem ser correlacionados com diferentes mobilidades de fronteira de grão e propriedades dieléctricas. Um modelo é sugerido, que se baseia na diminuição da fase líquida localizada nas fronteiras de grão, como o aumento da temperatura de sinterização, um cenário compatível com um fenómeno de solubilidade retrógrada, observado anteriormente em metais e semicondutores, mas não em cerâmicos. A EPD de filmes espessos de STO em substratos de folha de Pt e a sinterização constrangida dos filmes fabricados foram também preliminarmente tratadas. Filmes espessos de STO foram depositados com êxito por EPD sobre substratos de Pt e, depois de sinterizados, atingiram densidades elevadas. Um aumento da densificação e do tamanho de grão assim como o alargamento da distribuição de tamanho do grão foram observados com a diminuição da razão Sr/Ti, tal como anteriormente observado em amostras cerâmicas. Grãos equiaxiados foram observados para todas as composições, mas um certo grau de anisotropia na orientação dos poros foi detectado: os poros revelaram uma orientação vertical preferencial. Este trabalho focou-se também na sinterização constrangida do sistema BLnT (Ln = La ou Nd), nomeadamente de filmes espessos de BLT e BNT sobre substratos de folha de platina, e na relação do desenvolvimento de anisotropia microestrutural com as propriedades dieléctricas. As observações durante a sinterização constrangida foram comparadas com cerâmicos monolíticos equivalentes sinterizados livremente. Filmes espessos de BLnT (Ln = La ou Nd) com elevada densidade foram obtidos por EPD e subsequente sinterização constrangida. A anisometria cristalográfica do material em conjunto com um passo de sinterização constrangida resultou em grãos alongados e microestruturas anisotrópicas. O efeito do stress do substrato durante a sinterização constrangida originou graus mais elevados de anisotropia (grãos e poros alongados e orientação preferencial, bem como textura cristalográfica) nos filmes sinterizados relativamente aos cerâmicos equivalentes sinterizados livremente, não obstante o estado equivalente das amostras em verde. A densificação dos filmes de BLnT (Ln = La ou Nd) é retardada em comparação com os cerâmicos, mas depois de longos tempos de sinterização densidades semelhantes são obtidas. No entanto, em oposição a observações na sinterização constrangida de outros sistemas, o crescimento do grão em filmes de BLnT (Ln = La ou Nd) é favorecido pelo constrangimento causado pelo substrato. Além disso, grãos e poros alongados orientados paralelamente ao substrato foram desenvolvidos durante a sinterização constrangida de filmes espessos. Verificou-se uma forte correlação entre a evolução de grãos e poros, que começou assim que o crescimento do grão se iniciou. Um efeito da tensão do substrato no aumento do crescimento de grão, bem como um forte “Zener pinning”, origina microestruturas altamente texturizadas, o que também é observado a nível cristalográfico. Efeitos marcantes da anisotropia microestrutural foram também detectados nas propriedades dieléctricas dos filmes de BLnT (Ln = La ou Nd). Juntamente com o aumento da razão de aspecto dos grãos, do factor de orientação e do grau de textura cristalográfica, a permitividade relativa é ligeiramente diminuída e o coeficiente de temperatura da permitividade evolui de negativo para positivo com o aumento do tempo isotérmico de sinterização. Este trabalho mostra que a não-estequiometria pode ser usada para controlar a mobilidade das fronteiras de grão e, portanto, desenhar a microestrutura e as propriedades dieléctricas de electrocerâmicos à base de STO, com ênfase nas propriedades das fronteiras de grão. O papel da não-estequiometria no STO e dos complexos de fronteira de grão no desenvolvimento microestrutural é discutido e novas oportunidades para desenhar as propriedades de materiais funcionais são abertas. As observações relativamente à sinterização constrangida apontam para o efeito de tensões mecânicas desenvolvidas devido ao substrato subjacente no desenvolvimento da microestrutura de materiais funcionais. É assim esperado que a escolha adequada de substrato permitia desenhar a microestrutura de filmes espessos funcionais com desempenho optimizado. “Stress Assisted Grain Growth” (SAGG) é então proposto como uma técnica potencial para desenhar a microestrutura de materiais funcionais, originando microestruturas anisotrópicas texturizadas com propriedades desejadas.

Quantization effects in the polyphase N-path IIR structure

Polyphase IIR structures have recently proven themselves very attractive for very high performance filters that can be designed using very few coefficients. This, combined with their low sensitivity to coefficient quantization in comparison to standard FIR and IIR structures, makes them very applicable for very fast filtering when implemented in fixed-point arithmetic. However, although the mathematical description is very simple, there exist a number of ways to implement such filters. In this paper, we take four of these different implementation structures, analyze the rounding noise originating from the limited arithmetic wordlength of the mathematical operators, and check the internal data growth within the structure. These analyses need to be done to ensure that the performance of the implementation matches the performance of the theoretical design. The theoretical approach that we present has been proven by the results of the fixed-point simulation done in Simulink and verified by an equivalent bit-true implementation in VHDL.

Low Complexity All-Pass Based Polyphase Decimation Filters for ECG Monitoring

This paper presents a low complexity high efficiency decimation filter which can be employed in EletroCardioGram (ECG) acquisition systems. The decimation filter with a decimation ratio of 128 works along with a third order sigma delta modulator. It is designed in four stages to reduce cost and power consumption. The work reported here provides an efficient approach for the decimation process for high resolution biomedical data conversion applications by employing low complexity two-path all-pass based decimation filters. The performance of the proposed decimation chain was validated by using the MIT-BIH arrhythmia database and comparative simulations were conducted with the state of the art.

Microstructure, mechanical properties and chemical degradation of brazed AISI 316 stainless steel/alumina systems

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Pozzolanic components in lime mortars: correlating behaviour, composition and microstructure.

Int. J. for Restoration of Buildings and Monuments, vol.11, nº 2 (2005), p.111-118

Effet de la microstructure sur les propriétés excitoniques des polymères semi-conducteurs semi-cristallins

Les polymères semi-conducteurs semicristallins sont utilisés au sein de diodes électroluminescentes, transistors ou dispositifs photovoltaïques organiques. Ces matériaux peuvent être traités à partir de solutions ou directement à partir de leur état solide et forment des agrégats moléculaires dont la morphologie dicte en grande partie leurs propriétés optoélectroniques. Le poly(3-hexylthiophène) est un des polymères semi-conducteurs les plus étudiés. Lorsque le poids moléculaire (Mw) des chaînes est inférieur à 50 kg/mol, la microstructure est polycristalline et composée de chaînes formant des empilements-π. Lorsque Mw>50 kg/mol, la morphologie est semicristalline et composée de domaines cristallins imbriquées dans une matrice de chaînes amorphes. À partir de techniques de spectroscopie en continu et ultrarapide et appuyé de modèles théoriques, nous démontrons que la cohérence spatiale des excitons dans ce matériau est légèrement anisotrope et dépend de Mw. Ceci nous permet d’approfondir la compréhension de la relation intime entre le couplage inter et intramoléculaire sur la forme spectrale en absorption et photoluminescence. De plus, nous démontrons que les excitations photogénérées directement aux interfaces entre les domaines cristallins et les régions amorphes génèrent des paires de polarons liés qui se recombinent par effet tunnel sur des échelles de temps supérieures à 10ns. Le taux de photoluminescence à long temps de vie provenant de ces paires de charges dépend aussi de Mw et varie entre ∼10% et ∼40% pour les faibles et hauts poids moléculaires respectivement. Nous fournissons un modèle permettant d’expliquer le processus de photogénération des paires de polarons et nous élucidons le rôle de la microstructure sur la dynamique de séparation et recombinaison de ces espèces.

Studies on grain refinement and alloying additions on the microstructure and mechanical properties of Mg-8Zn-4Al alloy

MAGNESIUM ALLOYS have strong potential for weight reduction in a wide range of technical applications because of their low density compared to other structural metallic materials. Therefore, an extensive growth of magnesium alloys usage in the automobile sector is expected in the coming years to enhance the fuel efficiency through mass reduction. The drawback associated with the use of commercially cheaper Mg-Al based alloys, such as AZ91, AM60 and AM50 are their inferior creep properties above 100ºC due to the presence of discontinuous Mg17A112 phases at the grain boundaries. Although rare earth-based magnesium alloys show better mechanical properties, it is not economically viable to use these alloys in auto industries. Recently, many new Mg-Al based alloy systems have been developed for high temperature applications, which do not contain the Mg17Al12 phase. It has been proved that the addition of a high percentage of zinc (which depends upon the percentage of Al) to binary Mg-Al alloys also ensures the complete removal of the Mg17Al12 phase and hence exhibits superior high temperature properties.ZA84 alloy is one such system, which has 8%Zn in it (Mg-8Zn-4Al-0.2Mn, all are in wt %) and shows superior creep resistance compared to AZ and AM series alloys. These alloys are mostly used in die casting industries. However, there are certain large and heavy components, made up of this alloy by sand castings that show lower mechanical properties because of their coarse microstructure. Moreover, further improvement in their high temperature behaviour through microstructural modification is also an essential task to make this alloy suitable for the replacement of high strength aluminium alloys used in automobile industry. Grain refinement is an effective way to improve the tensile behaviour of engineering alloys. In fact, grain refinement of Mg-Al based alloys is well documented in literature. However, there is no grain refiner commercially available in the market for Mg-Al alloys. It is also reported in the literature that the microstructure of AZ91 alloy is modified through the minor elemental additions such as Sb, Si, Sr, Ca, etc., which enhance its high temperature properties because of the formation of new stable intermetallics. The same strategy can be used with the ZA84 alloy system to improve its high temperature properties further without sacrificing the other properties. The primary objective of the present research work, “Studies on grain refinement and alloying additions on the microstructure and mechanical properties of Mg-8Zn-4Al alloy” is twofold: 1. To investigate the role of individual and combined additions of Sb and Ca on the microstructure and mechanical properties of ZA84 alloy. 2. To synthesis a novel Mg-1wt%Al4C3 master alloy for grain refinement of ZA84 alloy and investigate its effects on mechanical properties.

Influence of Si, Sb and Sr Additions on the Microstructure, Mechanical Properties and Corrosion Behavior of AZ91 Magnesium Alloy

All the exciting work on developing new and better alloys has led older alloys, such as AZ9l , being abandoned by researchers. lt is believed that the full potential of AZ9l in automotive design has not been realized. Whatever works have been carried out on AZ9lalloy to improve its mechanical properties are insufficient in terms of its potential usage in auto industries. Due to the fact that AZ91 offers high room temperature mechanical properties and good castability, still this alloy is a primary choice for the auto component manufactures. Small improvement in its creep properties will have a huge impact in the transportation industries. Hence, in the present work, “Influence of Si, Sb and Sr Additions on the Microstructure, Mechanical Properties and Corrosion Behavior of AZ91 Magnesium Alloy”, an attempt has been made to improve the creep properties of AZ9l alloy through minor alloying elemental additions and to understand its strengthening mechanisms. The effect of alloying additions on the ageing and tensile properties of AZ9l is also studied. In addition to that, role of various intermetallics formed due to the alloying additions on the corrosion properties of AZ9l alloy is investigated.

Random-field Potts model with dipolarlike interactions: Hysteresis avalanches and microstructure

A model for the study of hysteresis and avalanches in a first-order phase transition from a single variant phase to a multivariant phase is presented. The model is based on a modification of the random-field Potts model with metastable dynamics by adding a dipolar interaction term truncated at nearest neighbors. We focus our study on hysteresis loop properties, on the three-dimensional microstructure formation, and on avalanche statistics.

Polyphase Implementation of Non-recursive Comb Decimators for Sigma-Delta A/D Converters

In a sigma-delta analog to digital (A/D) As most of the sigma-delta ADC applications require converter, the most computationally intensive block is decimation filters with linear phase characteristics, the decimation filter and its hardware implementation symmetric Finite Impulse Response (FIR) filters are may require millions of transistors. Since these widely used for implementation. But the number of FIR converters are now targeted for a portable application, filter coefficients will be quite large for implementing a a hardware efficient design is an implicit requirement. narrow band decimation filter. Implementing decimation In this effect, this paper presents a computationally filter in several stages reduces the total number of filter efficient polyphase implementation of non-recursive coefficients, and hence reduces the hardware complexity cascaded integrator comb (CIC) decimators for and power consumption [2]. Sigma-Delta Converters (SDCs). The SDCs are The first stage of decimation filter can be operating at high oversampling frequencies and hence implemented very efficiently using a cascade of integrators require large sampling rate conversions. The filtering and comb filters which do not require multiplication or and rate reduction are performed in several stages to coefficient storage. The remaining filtering is performed reduce hardware complexity and power dissipation. either in single stage or in two stages with more complex The CIC filters are widely adopted as the first stage of FIR or infinite impulse response (IIR) filters according to decimation due to its multiplier free structure. In this the requirements. The amount of passband aliasing or research, the performance of polyphase structure is imaging error can be brought within prescribed bounds by compared with the CICs using recursive and increasing the number of stages in the CIC filter. The non-recursive algorithms in terms of power, speed and width of the passband and the frequency characteristics area. This polyphase implementation offers high speed outside the passband are severely limited. So, CIC filters operation and low power consumption. The polyphase are used to make the transition between high and low implementation of 4th order CIC filter with a sampling rates. Conventional filters operating at low decimation factor of '64' and input word length of sampling rate are used to attain the required transition '4-bits' offers about 70% and 37% of power saving bandwidth and stopband attenuation. compared to the corresponding recursive and Several papers are available in literature that deals non-recursive implementations respectively. The same with different implementations of decimation filter polyphase CIC filter can operate about 7 times faster architecture for sigma-delta ADCs. Hogenauer has than the recursive and about 3.7 times faster than the described the design procedures for decimation and non-recursive CIC filters.

Microstructure and random magnetic anisotropy in Fe–Ni based nanocrystalline thin films

Nanocrystalline Fe–Ni thin films were prepared by partial crystallization of vapour deposited amorphous precursors. The microstructure was controlled by annealing the films at different temperatures. X-ray diffraction, transmission electron microscopy and energy dispersive x-ray spectroscopy investigations showed that the nanocrystalline phase was that of Fe–Ni. Grain growth was observed with an increase in the annealing temperature. X-ray photoelectron spectroscopy observations showed the presence of a native oxide layer on the surface of the films. Scanning tunnelling microscopy investigations support the biphasic nature of the nanocrystalline microstructure that consists of a crystalline phase along with an amorphous phase. Magnetic studies using a vibrating sample magnetometer show that coercivity has a strong dependence on grain size. This is attributed to the random magnetic anisotropy characteristic of the system. The observed coercivity dependence on the grain size is explained using a modified random anisotropy model