Architecture of European plastic surgery

The architecture of European Plastic Surgery was published in 1996 [Nicolai JPA, Scuderi N. Plastic surgical Europe in an organogram. Eur J Plast Surg 1996; 19: 253-256.] It is the objective of this paper to update information of that article. Continuing medical education (CME), science, training, examination, quality assurance and relations with the European Commission and Parliament all are aspects covered by the organisations to be discussed.

Asphyxial suicide by inhalation of helium inside a plastic bag

Asphyxial suicide by placing a plastic bag over the head, especially in combination with inhalation of gases, is a rarely described method of committing suicide. This article reports a case of suicidal asphyxiation by inhaling the inert gas helium inside a plastic bag. A 64-year-old man probably followed the instructions described in an article about committing suicide written by a medical practitioner from Zürich. This form of suicide is recommended by right-to-die groups and in the internet as a certain, fast, and painless suicide method. Additionally, it leaves only seldom externally visible marks or pathomorphological findings on the body. If the plastic bag and other auxiliary means are removed by another person, the forensic death investigation of cause and manner of death may be very difficult. Therefore, the death scene investigation and the inquiry ordered in the environment of the deceased are very important.

Pipes in Steel Ingots as Exemplified by Casting Wax

This paper presents some experimental data on the size and position of pipes steel ingots as exemp1ified by casting wax under various conditions and noting the size and location of the pipes formed. The results tend to show that the length of the pipe is decreased by: 1. Slow casting 2. By casting large end up instead of down 3. By retarding the cooling of the top

Are Warnings on Plastic Films Adequate?

Warnings are used to inform users of hazards that may be associated with many products. Often these warnings deal with the operation of tools, appliances, and other items for which the user may have some reason at least, to look for information on the product regarding its use. Plastic film presents a serious hazard to young children. Because the film will adhere to the flesh, if it covers the airways for the child, suffocation may result. Because young children may play with them, it is important that such films be kept away from them. Warnings need to be adequate to inform or remind caregivers of this fact. This study examined warnings found on various items in commerce and some alternatives to those warnings. The results showed some warnings to be poor at best. The alternative most preferred included both the prohibition sign and a symbolic indication of proper disposal.

The STEREO/PLASTIC response to solar wind ions (Flight measurements and models)

The Plasma and Supra-Thermal Ion Composition (PLASTIC) instrument is one of four experiment packages on board of the two identical STEREO spacecraft A and B, which were successfully launched from Cape Canaveral on 26 October 2006. During the two years of the nominal STEREO mission, PLASTIC is providing us with the plasma characteristics of protons, alpha particles, and heavy ions. PLASTIC will also provide key diagnostic measurements in the form of the mass and charge state composition of heavy ions. Three measurements (E/qk, time of flight, ESSD) from the pulse height raw data are used to characterize the solar wind ions from the solar wind sector, and part of the suprathermal particles from the wide-angle partition with respect to mass, atomic number and charge state. In this paper, we present a new method for flight data analysis based on simulations of the PLASTIC response to solar wind ions. We present the response of the entrance system / energy analyzer in an analytical form. Based on stopping power theory, we use an analytical expression for the energy loss of the ions when they pass through a thin carbon foil. This allows us to model analytically the response of the time of flight mass spectrometer to solar wind ions. Thus we present a new version of the analytical response of the solid state detectors to solar wind ions. Various important parameters needed for our models were derived, based on calibration data and on the first flight measurements obtained from STEREO-A. We used information from each measured event that is registered in full resolution in the Pulse Height Analysis words and we derived a new algorithm for the analysis of both existing and future data sets of a similar nature which was tested and works well. This algorithm allows us to obtain, for each measured event, the mass, atomic number and charge state in the correct physical units. Finally, an important criterion was developed for filtering our Fe raw flight data set from the pulse height data without discriminating charge states.

From transient to steady state deformation and grain size: A thermodynamic approach using elasto-visco-plastic numerical modeling

Numerical simulation experiments give insight into the evolving energy partitioning during high-strain torsion experiments of calcite. Our numerical experiments are designed to derive a generic macroscopic grain size sensitive flow law capable of describing the full evolution from the transient regime to steady state. The transient regime is crucial for understanding the importance of micro structural processes that may lead to strain localization phenomena in deforming materials. This is particularly important in geological and geodynamic applications where the phenomenon of strain localization happens outside the time frame that can be observed under controlled laboratory conditions. Ourmethod is based on an extension of the paleowattmeter approach to the transient regime. We add an empirical hardening law using the Ramberg-Osgood approximation and assess the experiments by an evolution test function of stored over dissipated energy (lambda factor). Parameter studies of, strain hardening, dislocation creep parameter, strain rates, temperature, and lambda factor as well asmesh sensitivity are presented to explore the sensitivity of the newly derived transient/steady state flow law. Our analysis can be seen as one of the first steps in a hybrid computational-laboratory-field modeling workflow. The analysis could be improved through independent verifications by thermographic analysis in physical laboratory experiments to independently assess lambda factor evolution under laboratory conditions.

Bone-added periodontal plastic surgery: a new approach in esthetic dentistry

This article proposes a combined technique including bone grafting, connective tissue graft, and coronally advanced flap to create some space for simultaneous bone regrowth and root coverage. A 23 year-old female was referred to our private clinic with a severe class II Miller recession and lack of attached gingiva. The suggested treatment plan comprised of root coverage combined with xenograft bone particles. The grafted area healed well and full coverage was achieved at 12-month follow-up visit. Bone-added periodontal plastic surgery can be considered as a practical procedure for management of deep gingival recession without buccal bone plate.

Black Degradable Plastic Mulch Evaluation

Black polyethylene plastic mulch provides many benefits to fruit and vegetable producers. It increases earliness by increasing spring soil temperatures, conserves soil moisture, and reduces pesticide usage by decreasing weed and disease pressure. Furthermore, during seasons of high precipitation, it protects fertilizer from leaching below the root zone. Unfortunately, polyethylene mulches do not degrade and must be removed from the field and discarded each season. This is a labor-intensive process whether it is done mechanically or by hand. Several degradable plastic mulches have been developed that are designed to be incorporated into the soil profile, eliminating the need for removal, with no negative impact on soil quality or health. However, these degradable plastics often do not meet degradation expectations (either degrade too quickly or degrade incompletely and require manual removal). The objective of this project was to evaluate several degradable mulches for storage life, ease of use, and influence on tomato production.