Detection of Biological CO2 and 1,3-Pentadiene Using Non-refrigerated Low-Cost MWIR Detectors

The early detection of spoiling metabolic products in contaminated food is a very important tool to control quality. Some volatile compounds produce unpleasant odours at very low concentrations, making their early detection very challenging. This is the case of 1,3-pentadiene produced by microorganisms through decarboxylation of the preservative sorbate. In this work, we have developed a methodology to use the data produced by a low-cost, compact MWIR (Mid-Wave IR) spectrometry device without moving parts, which is based on a linear array of 128 elements of VPD PbSe coupled to a linear variable filter (LVF) working in the spectral range between 3 and 4.6 ?m. This device is able to analyze food headspace gases through dedicated sample presentation setup. This methodology enables the detection of CO2 and the volatile compound 1,3-pentadiene, as compared to synthetic patrons. Data analysis is based on an automated multidimensional dynamic processing of the MWIR spectra. Principal component and discriminant analysis allow segregating between four yeast strains including producers and no producers. The segregation power is accounted as a measure of the discrimination quality.

Improved modeling of photoluminescent and electroluminescent coupling in multijunction solar cells

The performance of tandem stacks of Group III?V multijunction solar cells continues to improve rapidly, both through improved performance of the individual cells in the stack and throughi ncrease in the number of stacked cells. As the radiative efficiency of these individual cells increases, radiative coupling between the stacked cells becomes an increasingly important factor not only in cell design, but also in accurate efficiency measurement and in determining performance of cells and systems under varying spectral conditions in the field. Past modeling has concentrated on electroluminescent coupling between the cells, although photoluminescent coupling is shown to be important for cells operating near their maximum power point voltage or below or when junction defect recombination is significant. Extension of earlier models i sproposed to allow this non-negligible component of luminescent coupling to be included. Therefined model is validated by measurement of the closely related external emission from both single and double junction cells.

Analysis of the behavior of multijunction solar cells under high irradiance Gaussian light profiles showing chromatic aberration with emphasis on tunnel junction performance

In this work, we explain the behavior of multijunction solar cells under non-uniform (spatially and in spectral content) light profiles in general and in particular when Gaussian light profiles cause a photo-generated current density, which exceeds locally the peak current density of the tunnel junction. We have analyzed the implications on the tunnel junction's limitation, that is, in the loss of efficiency due to the appearance of a dip in the I–V curve. For that, we have carried out simulations with our three-dimensional distributed model for multijunction solar cells, which contemplates a full description of the tunnel junction and also takes into account the lateral resistances in the tunnel junction. The main findings are that the current density photo-generated spreads out through the lateral resistances of the device, mainly through the tunnel junction layers and the back contact. Therefore, under non-uniform light profiles these resistances are determinant not only to avoid the tunnel junction's limitation but also for mitigating losses in the fill factor. Therefore, taking into account these lateral resistances could be the key for jointly optimizing the concentrator photovoltaic system (concentrator optics, front grid layout and semiconductor structure)

Piezoelectric sensing and non-parametric statistical signal processing for health monitoring of hysteretic dampers used in seismic-resistant structures

The paper proposes a new application of non-parametric statistical processing of signals recorded from vibration tests for damage detection and evaluation on I-section steel segments. The steel segments investigated constitute the energy dissipating part of a new type of hysteretic damper that is used for passive control of buildings and civil engineering structures subjected to earthquake-type dynamic loadings. Two I-section steel segments with different levels of damage were instrumented with piezoceramic sensors and subjected to controlled white noise random vibrations. The signals recorded during the tests were processed using two non-parametric methods (the power spectral density method and the frequency response function method) that had never previously been applied to hysteretic dampers. The appropriateness of these methods for quantifying the level of damage on the I-shape steel segments is validated experimentally. Based on the results of the random vibrations, the paper proposes a new index that predicts the level of damage and the proximity of failure of the hysteretic damper

Spectral bifurcations in dispersive wave turbulence

Dispersive wave turbulence is studied numerically for a class of one-dimensional nonlinear wave equations. Both deterministic and random (white noise in time) forcings are studied. Four distinct stable spectra are observed—the direct and inverse cascades of weak turbulence (WT) theory, thermal equilibrium, and a fourth spectrum (MMT; Majda, McLaughlin, Tabak). Each spectrum can describe long-time behavior, and each can be only metastable (with quite diverse lifetimes)—depending on details of nonlinearity, forcing, and dissipation. Cases of a long-live MMT transient state dcaying to a state with WT spectra, and vice-versa, are displayed. In the case of freely decaying turbulence, without forcing, both cascades of weak turbulence are observed. These WT states constitute the clearest and most striking numerical observations of WT spectra to date—over four decades of energy, and three decades of spatial, scales. Numerical experiments that study details of the composition, coexistence, and transition between spectra are then discussed, including: (i) for deterministic forcing, sharp distinctions between focusing and defocusing nonlinearities, including the role of long wavelength instabilities, localized coherent structures, and chaotic behavior; (ii) the role of energy growth in time to monitor the selection of MMT or WT spectra; (iii) a second manifestation of the MMT spectrum as it describes a self-similar evolution of the wave, without temporal averaging; (iv) coherent structures and the evolution of the direct and inverse cascades; and (v) nonlocality (in k-space) in the transferral process.

Nanomateriais luminescentes de terras raras utilizando complexos de benzenotricarboxilatos como precursores

O material Y2O3:Eu3+ vem sendo usado comercialmente como luminóforo vermelho desde da década de 1960, em uma grande variedade de aplicações devido ao seu elevado rendimento quântico (próximo de 100 %), elevada pureza de cor e boa estabilidade. Portanto, este trabalho propõe um novo método de síntese baseado nos complexos benzenotricarboxilatos (BTC) de terras raras trivalentes (RE3+) dopados com íons Eu3+. O objetivo principal é produzir materiais luminescente RE2O3:Eu3+ a temperatura mais baixa (500 °C) e em escala nanométrica. Os complexos precursores [RE(BTC):Eu3+] e [RE(TLA)·n(H2O):Eu3+], onde RE3+: Y, Gd e Lu; BTC: ácido trimésico (TMA) e ácido trimelítico (TLA) foram calcinados em diferentes temperaturas de 500 a 1000 °C, a fim de obter os materiais luminescentes RE2O3:Eu3+. Os complexos foram caracterizados por análise elementar de carbono e hidrogênio, analise térmica (TG), espectroscopia de absorção no infravermelho (FTIR), difração de raios-X - método do pó (XPD) e microscopia eletrônica de varredura (SEM). Todos os complexos são cristalinos e termo estáveis até 460 °C. Dados de fosforescência dos complexos de Y, Gd e Lu mostram que o nível T1 do aníon BTC3- tem energia acima do nível emissor 5D0 do íon Eu3+, indicando que os ligantes podem atuar como sensibilizadores de energia intramolecular. O estudo das propriedades fotoluminescentes dos complexos dopados foi baseado nos espectros de excitação e emissão e curvas de decaimento de luminescência. Ademais, foram determinados os parâmetros de intensidades experimentais (Ωλ), tempos de vida (τ), taxas de decaimentos radiativo (Arad) e não-radiativo (Anrad). Os materiais luminescentes RE2O3:Eu3+ foram sintetizados de forma bem sucedida por meio do método benzenotricarboxilatos calcinados a 500, 600, 700, 800, 900 e 1000 °C, apresentando alta homogeneidade química e controle de tamanho de cristalito. Os nanomateriais foram caracterizados pelas técnicas de FTIR, XPD SEM e TEM revelando a obtenção dos materiais C-RE2O3:Eu3+ mesmo a 500 °C. Os dados de XPD dos materiais confirmaram um aumento do tamanho dos cristalitos de 5 até 52 nm (equação de Scherrer) de em função da temperatura de calcinação de 500 a 1000 °C, respectivamente, corroborados pelas técnicas de SEM e TEM. Os espectros de emissão de RE2O3:Eu3+ mostram uma banda larga atribuída a transição interconfiguracional de transferência de carga ligante-metal (LMCT) em 260 nm, i.e. O2-(2p)→Eu3+(4f6). Além disso, foram observadas linhas finas de absorção devido as transições intraconfiguracionais 4f do íon európio (7F0,1𔾹LJ; J: 0, 1, 2, 3 e 4), como esperado. As propriedades fotoluminescentes dos luminóforos foram baseadas nos espectros (excitação e emissão) e curvas de decaimento luminescente. Os parâmetros de intensidade experimental, tempos de vida, assim como as taxas de decaimentos radiativos e não radiativos foram calculados. As propriedades fotônicas dos nanomateriais são consistentes com o sítio de baixa simetria C2 ocupado pelo íon Eu3+ no C-RE2O3:Eu3+, produzindo emissão vermelha dominada pela transição hipersensível 5D0𔾻F2 do íon Eu3+ no sitio C2, ao invés do sítio centrossimétrico S6. Além disso, os nanomateriais Y2O3:Eu3+ exibem características espectroscópicas semelhantes e elevados valores de eficiência quântica (η~91 %), compatível com os luminóforos comerciais disponíveis no mercado. Este novo método pode ser utilizado para o desenvolvimento de novos nanomateriais contendo íons terras raras, assim como outros íons metálicos.

Carbon assimilation, herbage accumulation, nutritive value, and grazing efficiency of Mulato II brachiariagrass under continuous stocking

Grazed pastures are the backbone of the Brazilian livestock industry and grasses of the genus Brachiaria (syn. Urochloa) are some of most used tropical forages in the country. Although the dependence on the forage resource is high, grazing management is often empirical and based on broad and non-specific guidelines. Mulato II brachiariagrass (Convert HD 364, Dow AgroSciences, São Paulo, Brazil) (B. brizantha × B. ruziziensis × B. decumbens), a new Brachiaria hybrid, was released as an option for a broad range of environmental conditions. There is no scientific information on specific management practices for Mulato II under continuous stocking in Brazil. The objectives of this research were to describe and explain variations in carbon assimilation, herbage accumulation (HA), plant-part accumulation, nutritive value, and grazing efficiency (GE) of Mulato II brachiariagrass as affected by canopy height and growth rate, the latter imposed by N fertilization rate, under continuous stocking. An experiment was carried out in Piracicaba, SP, Brazil, during two summer grazing seasons. The experimental design was a randomized complete block, with a 3 x 2 factorial arrangement, corresponding to three steady-state canopy heights (10, 25 and 40 cm) maintained by mimicked continuous stocking and two growth rates (imposed as 50 and 250 kg N ha-1 yr-1), with three replications. There were no height × N rate interactions for most of the responses studied. The HA of Mulato II increased linearly (8640 to 13400 kg DM ha-1 yr-1), the in vitro digestible organic matter (IVDOM) decreased linearly (652 to 586 g kg-1), and the GE decreased (65 to 44%) as canopy height increased. Thus, although GE and IVDOM were greatest at 10 cm height, HA was 36% less for the 10- than for the 40-cm height. The leaf carbon assimilation was greater for the shortest canopy (10 cm), but canopy assimilation was less than in taller canopies, likely a result of less leaf area index (LAI). The reductions in HA, plant-part accumulation, and LAI, were not associated with other signs of stand deterioration. Leaf was the main plant-part accumulated, at a rate that increased from 70 to 100 kg DM ha-1 d-1 as canopy height increased from 10 to 40 cm. Mulato II was less productive (7940 vs. 13380 kg ha-1 yr-1) and had lesser IVDOM (581 vs. 652 g kg-1) at the lower N rate. The increase in N rate affected plant growth, increasing carbon assimilation, LAI, rates of plant-part accumulation (leaf, stem, and dead), and HA. The results indicate that the increase in the rate of dead material accumulation due to more N applied is a result of overall increase in the accumulation rates of all plant-parts. Taller canopies (25 or 40 cm) are advantageous for herbage accumulation of Mulato II, but nutritive value and GE was greater for 25 cm, suggesting that maintaining ∼25-cm canopy height is optimal for continuously stocked Mulato II.

Hot thermal X-ray emission from the Be star HD 119682

We present an analysis of a series of four consecutive Chandra high-resolution transmission gratings observations, amounting to a total of 150 ks, of the Be X-ray source HD 119682 (=1WGA J1346.5–6255), a member of the new class of γ Cas analogs. The Chandra light curve shows significant brightness variations on timescales of hours. However, the spectral distribution appears rather stable within each observation and during the whole campaign. A detailed analysis is not able to detect any coherent pulsation up to a frequency of 0.05 Hz. The Chandra High Energy Transmission Gratings spectrum seems to be devoid of any strong emission line, including Fe Kα fluorescence. The continuum is well described with the addition of two collisionally ionized plasmas of temperatures kT ≈ 15 keV and 0.2 keV, respectively, by the apec model. Models using photoionized plasma components (mekal) or non-thermal components (powerlaw) give poorer fits, providing support for the pure thermal scenario. These two components are absorbed by a single column with N H = (0.20+0.15 –0.03) × 1022 cm–2 compatible with the interstellar value. We conclude that HD 119682 can be regarded as a pole-on γ Cas analog.

Pulse phase-coherent timing and spectroscopy of CXOU J164710.2−45521 outbursts

We present a long-term phase-coherent timing analysis and pulse-phase resolved spectroscopy for the two outbursts observed from the transient anomalous X-ray pulsar CXOU J164710.2−455216. For the first outburst we used 11 Chandra and XMM–Newton observations between 2006 September and 2009 August, the longest baseline yet for this source. We obtain a coherent timing solution with P = 10.61065583(4) s, Ṗ = 9.72(1) × 10−13 s s−1 and P̈ = –1.05(5) × 10−20 s s−2. Under the standard assumptions this implies a surface dipolar magnetic field of ∼1014 G, confirming this source as a standard B magnetar. We also study the evolution of the pulse profile (shape, intensity and pulsed fraction) as a function of time and energy. Using the phase-coherent timing solution we perform a phase-resolved spectroscopy analysis, following the spectral evolution of pulse-phase features, which hints at the physical processes taking place on the star. The results are discussed from the perspective of magnetothermal evolution models and the untwisting magnetosphere model. Finally, we present similar analysis for the second, less intense, 2011 outburst. For the timing analysis we used Swift data together with 2 XMM–Newton and Chandra pointings. The results inferred for both outbursts are compared and briefly discussed in a more general framework.

Non-Viral Gene Therapy to Cells of the bovine Intervertebral Disc

Background. Low back pain is an increasing global health problem, which is associated with intervertebral disc (IVD) damage and degeneration. Major changes occur in the nucleus pulposus (NP), with the degradation of the extracellular matrix (ECM).1 Further studies showed that growth factors from transforming growth factor β (TGFβ) and bone morphogenic proteins (BMP) family may induce chondrogenic differentiation of mesenchymal stem cells (MSC).2 Focusing on non-viral gene therapies and their possible translation into the clinics, we investigated if GDF6 (syn. BMP13 or CDMP2) can induce regeneration of degraded NP. We hypothesized that IVD transfected with plasmid over-expressing GDF6 also up-regulates other NP- and chondrogenic cell markers and enhances ECM deposition. Methods. Bovine nucleus pulposus (bNPC) and annulus fibrosus cells (bAFC) were harvested from bovine coccygeal IVD. Primary cells were then electroporized with plasmid GDF6 (Origene, vector RG211366) by optimizing parameters using the Neon Transfection system (Life Technologies, Basel). After transfection, cells were cultured in 2D monolayer or 3D alginate beads for 7, 14 or 21 days. Transfection efficiency of pGDF6 was analyzed by immunohistochemistry and fluorescent microscopy. Cell phenotype was quantified by real-time RT-PCR. To test a non-viral gene therapy applied directly to 3D whole organ culture, coccygeal bovine IVDs were harvested as previously described. Bovine IVDs were transfected by injection of plasmid GDF6 into the center. Electroporation was performed with ECM830 Square Wave Electroporation System (Harvard Apparatus, MA) using 2-needle array electrode or tweezertrodes. 72 h after tranfection discs were fixed and cryosectioned and analyzed by immunofluorescence against GDF6. Results. RT-PCR and immunohistochemistry confirmed up-regulation of GFP and GDF6 in the primary bNPC/bAFC culture. The GFP-tagged GDF6 protein, however, was not visible, possibly due to failure of dimer formation as a result of fusion structure. Organ IVD culture transfection revealed GDF6 positive staining in the center of the disc using 2-needle array electrode. Results from tweezertrodes did not show any GDF6 positive cells. Conclusion. Non-viral transfection is an appealing approach for gene therapy as it fulfills the translational safety aspects of transiency and lacks the toxic effects of viral transduction. We identified novel parameters to successfully transfect primary bovine IVD cells. For transfection of whole IVD explants electroporation parameters need to be further optimized. Acknowledgements. This project was funded by the Lindenhof Foundation (Funds “Research & Teaching”) Project no. 13-02-F. The imaging part of this study was performed with the facility of the Microscopy Imaging Center (MIC), University of Bern. References. Roughly PJ (2004): Spine (Phila), 29:2691-2699 Clarke LE, McConell JC, Sherratt MJ, Derby B, Richardson SM, Hoyland JA (2014), Arthritis Research & Therapy, 16:R67

Comparison of Lagrangian Coherent Structures and Relative Dispersion in a Mixing Layer

Thesis (Master's)--University of Washington, 2016-06

Creation of maximally entangled photon-number states using optical fiber multiports

We theoretically demonstrate a method for producing the maximally path-entangled state (1/root2)(\N,0>+exp[iNphi]\0,N>) using intensity-symmetric multiport beam splitters, single photon inputs, and either photon-counting postselection or conditional measurement. The use of postselection enables successful implementation with non-unit efficiency detectors. We also demonstrate how to make the same state more conveniently by replacing one of the single photon inputs by a coherent state.

The North Pacific biological pump: Rates, efficiency and influence on ocean carbon uptake

Thesis (Ph.D.)--University of Washington, 2016-05

Coherent state construction of representations of osp(2|2) and primary fields of osp(2|2) conformal field theory

Representations of the superalgebra osp(2/2)(k)((1)) and current superalgebra. osp(2/2)k in the standard basis are investigated. All finite-dimensional typical and atypical representations of osp(2/2) are constructed by the vector coherent state method. Primary fields of the non-unitary conformal field theory associated with osp(2/2)(k)((1)) in the standard basis are obtained for arbitrary level k. (C) 2004 Elsevier B.V. All rights reserved.

Trade liberalisation and technical efficiency: Evidence from Bangladesh manufacturing industries

The paper investigates the effects of trade liberalisation on the technical efficiency of the Bangladesh manufacturing sector by estimating a combined stochastic frontier-inefficiency model using panel data for the period 197894 for 25 three-digit level industries. The results show that the overall technical efficiency of the manufacturing sector as well as the technical efficiencies of the majority of the individual industries has increased over time. The findings also clearly suggest that trade liberalisation, proxied by export orientation and capital deepening, has had significant impact on the reduction of the overall technical inefficiency. Similarly, the scale of operation and the proportion of non-production labour in total employment appear as important determinants of technical inefficiency. The evidence also indicates that both export-promoting and import-substituting industries have experienced rises in technical efficiencies over time. Besides, the results are suggestive of neutral technical change, although (at the 5 per cent level of significance) the empirical results indicate that there was no technical change in the manufacturing industries. Finally, the joint test based on the likelihood ratio (LR) test rejects the Cobb-Douglas production technology as description of the database given the specification of the translog production technology.