FIA potentiometric system based on periodate polymeric membrane sensors for the assessment of ascorbic acid in commercial drinks

Ascorbic acid is found in many food samples. Its clinical and technological importance demands an easyto- use, rapid, robust and inexpensive method of analysis. For this purpose, this work proposes a new flow procedure based on the oxidation of ascorbic acid by periodate. A new potentiometric periodate sensor was constructed to monitor this reaction. The selective membranes were of PVC with porphyrin-based sensing systems and a lipophilic cation as additive. The sensor displayed a near-Nernstian response for periodate over 1.0x10-2–6.0x10-6 M, with an anionic slope of 73.9 ± 0.9 mV decade-1. It was pH independent in acidic media and presented good selectivity features towards several inorganic anions. The flow set-up operated in double-channel, carrying a 5.0x10-4 M IO- 4 solution and a suitable buffer; these were mixed in a 50-cm reaction coil. The overall flow rate was 7 ml min-1 and the injection volume 70 µl. Under these conditions, a linear behaviour against concentration was observed for 17.7–194.0 µg ml-1, presenting slopes of 0.169 mV (mg/l)-1, a reproducibility of ±1.1 mV (n = 5), and a sampling rate of ~96 samples h-1. The proposed method was applied to the analysis of beverages and pharmaceuticals.

Health-related behavior and quality of life among the elderly: a population-based study

OBJECTIVE: To assess the association between health-related behaviors and quality of life among the elderly. METHODS: A population-based cross-sectional study was carried out including 1,958 elderly living in four areas in the state of São Paulo, southeastern Brazil, 2001/2002. Quality of life was assessed using the Medical Outcomes Study SF-36-Item Short Form Health Survey instrument. This instrument's eight subscales and two components were the dependent variables. Independent variables were physical activity, weekly frequency of alcohol consumption and smoking. Multiple linear regression models were used to control for the effect of gender, age, schooling, work, area of residence and number of chronic conditions. RESULTS: Physical activity was positively associated with the eight SF-36 subscales. The stronger associations were found for role-physical (β=11.9), physical functioning (β=11.3) and physical component. Elderly individuals who consumed alcohol at least once a week showed a better quality of life than those did not consume alcohol. Compared to non-smokers, smokers had a poorer quality of life for the mental component (β=-2.4). CONCLUSIONS: The study results showed that physical activity, moderate alcohol consumption and no smoking are positively associated with a better quality of life in the elderly.

Interlimb relation during the double support phase of gait: an electromyographic, mechanical and energy based analysis

The purpose of this study is to analyse the interlimb relation and the influence of mechanical energy on metabolic energy expenditure during gait. In total, 22 subjects were monitored as to electromyographic activity, ground reaction forces and VO2 consumption (metabolic power) during gait. The results demonstrate a moderate negative correlation between the activity of tibialis anterior, biceps femoris and vastus medialis of the trailing limb during the transition between midstance and double support and that of the leading limb during double support for the same muscles, and between these and gastrocnemius medialis and soleus of the trailing limb during double support. Trailing limb soleus during the transition between mid-stance and double support was positively correlated to leading limb tibialis anterior, vastus medialis and biceps femoris during double support. Also, the trailing limb centre of mass mechanical work was strongly influenced by the leading limbs, although only the mechanical power related to forward progression of both limbs was correlated to metabolic power. These findings demonstrate a consistent interlimb relation in terms of electromyographic activity and centre of mass mechanical work, being the relations occurred in the plane of forward progression the more important to gait energy expenditure.

Ferramenta de apoio ao projeto, configuração e gestão de instalações domóticas

Esta dissertação apresenta o trabalho realizado no âmbito da unidade curricular de Tese / Dissertação (TEDI) do Mestrado em Engenharia Eletrotécnica e de Computadores – Especialização em Automação e Sistemas em parceria com a empresa Live Simply, uma empresa de domótica que decidiu apostar na inovação e no desenvolvimento de serviços e produtos de valor acrescentado para consolidar a sua posição no mercado. Neste contexto, foram identificadas como mais-valias para a Live Simply a conceção, por um lado, de uma ferramenta de apoio técnico de integração e simplificação das fases de projeto, configuração e gestão de instalações domóticas e, por outro lado, de uma interface com a instalação para o cliente consultar e alterar, em tempo real, o estado dos atuadores. Depois de analisadas as tecnologias disponíveis, selecionaram-se as soluções a adotar (linguagens de programação, servidores de base de dados e ambientes de desenvolvimento), definiu-se a arquitetura do sistema, detalhando-se os módulos de projeto, configuração e gestão de instalações, a estrutura da base de dados assim como o hardware de controlo da instalação. De seguida, procedeu-se ao desenvolvimento dos módulos de software e à configuração e programação do módulo de hardware. Por último, procedeu-se a um conjunto exaustivo de testes aos diferentes módulos que demonstraram o correto funcionamento da ferramenta e a adequação das tecnologias empregues. A ferramenta de apoio técnico realizada integra as fases do projeto, configuração e gestão de instalações domóticas, permitindo melhorar o desempenho dos técnicos e a resposta aos clientes. A interface oferecida ao dono da instalação é uma interface Web de aspeto amigável e fácil utilização que permite consultar e modificar em tempo real o estado da instalação.

Optimização da gestão de energia e da segurança de um edifício baseada num sistema técnico centralizado

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica Perfil Energia, Refrigeração e Climatização

Optimization of a microplate-based assay to assess esterase activity in the alga Pseudokirchneriella subcapitata

The present work describes the optimization of a short-term assay, based on the inhibition of the esterase activity of the alga Pseudokirchneriella subcapitata, in a microplate format. The optimization of the staining procedure showed that the incubation of the algal cells with 20 μmolL−1 fluorescein diacetate (FDA) for 40 min allowed discrimination between metabolic active and inactive cells. The shortterm assay was tested using Cu as toxicant. For this purpose, algal cells, in the exponential or stationary phase of growth, were exposed to the heavy metal in growing conditions. After 3 or 6 h, cells were subsequently stained with FDA, using the optimized procedure. For Cu, the 3- and 6-h EC50 values, based on the inhibition of the esterase activity of algal cells in the exponential phase of growth, were 209 and 130 μg L−1, respectively. P. subcapitata cells, in the stationary phase of growth, displayed higher effective concentration values than those observed in the exponential phase. The 3- and 6-h EC50 values for Cu, for cells in the stationary phase, were 443 and 268 μgL−1, respectively. This short-term microplate assay showed to be a rapid endpoint for testing toxicity using the alga P. subcapitata. The small volume required, the simplicity of the assay (no washing steps), and the automatic reading of the fluorescence make the assay particularly well suited for the evaluation of the toxicity of a high number of environmental samples.

Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

QoS-based surrogates selection and service proposal formulation in offloading environments

Resource constraints are becoming a problem as many of the wireless mobile devices have increased generality. Our work tries to address this growing demand on resources and performance, by proposing the dynamic selection of neighbor nodes for cooperative service execution. This selection is in uenced by user's quality of service requirements expressed in his request, tailoring provided service to user's speci c needs. In this paper we improve our proposal's formulation algorithm with the ability to trade o time for the quality of the solution. At any given time, a complete solution for service execution exists, and the quality of that solution is expected to improve overtime.

Geostatistical Prediction of Ocean Outfall Plume Characteristics Based on an Autonomous Underwater Vehicle

Geostatistics has been successfully used to analyze and characterize the spatial variability of environmental properties. Besides giving estimated values at unsampled locations, it provides a measure of the accuracy of the estimate, which is a significant advantage over traditional methods used to assess pollution. In this work universal block kriging is novelty used to model and map the spatial distribution of salinity measurements gathered by an Autonomous Underwater Vehicle in a sea outfall monitoring campaign, with the aim of distinguishing the effluent plume from the receiving waters, characterizing its spatial variability in the vicinity of the discharge and estimating dilution. The results demonstrate that geostatistical methodology can provide good estimates of the dispersion of effluents that are very valuable in assessing the environmental impact and managing sea outfalls. Moreover, since accurate measurements of the plume’s dilution are rare, these studies might be very helpful in the future to validate dispersion models.

From simulation to statistical analysis: timeliness assessment of ethernet/IP-based distributed systems

A number of characteristics are boosting the eagerness of extending Ethernet to also cover factory-floor distributed real-time applications. Full-duplex links, non-blocking and priority-based switching, bandwidth availability, just to mention a few, are characteristics upon which that eagerness is building up. But, will Ethernet technologies really manage to replace traditional Fieldbus networks? Ethernet technology, by itself, does not include features above the lower layers of the OSI communication model. In the past few years, it is particularly significant the considerable amount of work that has been devoted to the timing analysis of Ethernet-based technologies. It happens, however, that the majority of those works are restricted to the analysis of sub-sets of the overall computing and communication system, thus without addressing timeliness at a holistic level. To this end, we are addressing a few inter-linked research topics with the purpose of setting a framework for the development of tools suitable to extract temporal properties of Commercial-Off-The-Shelf (COTS) Ethernet-based factory-floor distributed systems. This framework is being applied to a specific COTS technology, Ethernet/IP. In this paper, we reason about the modelling and simulation of Ethernet/IP-based systems, and on the use of statistical analysis techniques to provide usable results. Discrete event simulation models of a distributed system can be a powerful tool for the timeliness evaluation of the overall system, but particular care must be taken with the results provided by traditional statistical analysis techniques.

Mechanisms for reflection-based monitoring of real- time systems

Monitoring is a very important aspect to consider when developing real-time systems. However, it is also important to consider the impact of the monitoring mechanisms in the actual application. The use of Reflection can provide a clear separation between the real-time application and the implemented monitoring mechanisms, which can be introduced (reflected) into the underlying system without changing the actual application part of the code. Nevertheless, controlling the monitoring system itself is still a topic of research. The monitoring mechanisms must contain knowledge about “how to get the information out”. Therefore, this paper presents the ongoing work to define a suitable strategy for monitoring real-time systems through the use of Reflection.

Association between tooth loss and obesity in Brazilian adults: a population-based study

OBJECTIVE: To examine the association between tooth loss and general and central obesity among adults. METHODS: Population-based cross-sectional study with 1,720 adults aged 20 to 59 years from Florianópolis, Southern Brazil. Home interviews were performed and anthropometric measures were taken. Information on sociodemographic data, self-reported diabetes, self-reported number of teeth, central obesity (waist circumference [WC] > 88 cm in women and > 102 cm in men) and general obesity (body mass index [BMI] ≥ 30 kg/m²) was collected. We used multivariable Poisson regression models to assess the association between general and central obesity and tooth loss after controlling for confounders. We also performed simple and multiple linear regressions by using BMI and WC as continuous variables. Interaction between age and tooth loss was also assessed. RESULTS: The mean BMI was 25.9 kg/m² (95%CI 25.6;26.2) in men and 25.4 kg/m2 (95%CI 25.0;25.7) in women. The mean WC was 79.3 cm (95%CI 78.4;80.1) in men and 88.4 cm (95%CI 87.6;89.2) in women. A positive association was found between the presence of less than 10 teeth in at least one arch and increased mean BMI and WC after adjusting for education level, self-reported diabetes, gender and monthly per capita income. However, this association was lost when the variable age was included in the model. The prevalence of general obesity was 50% higher in those with less than 10 teeth in at least one arch when compared with those with 10 or more teeth in both arches after adjusting for education level, self-reported diabetes and monthly per capita family income. However, the statistical significance was lost after controlling for age. CONCLUSIONS: Obesity was associated with number of teeth, though it depended on the participants' age groups.

Constructing and Using Multimodal Narratives to Research in Science Education: Contributions Based on Practical Classroom

This study deals with the problem of how to collect genuine and useful data about science classroom practices, and preserving the complex and holistic nature of teaching and learning. Additionally, we were looking for an instrument that would allow comparability and verifiability for teaching and research purposes. Given the multimodality of teaching and learning processes, we developed the multimodal narrative (MN), which describes what happens during a task and incorporates data such as examples of students’ work.

INDEPTH: timeliness assessment of ethernet/IP-based systems

The continuous improvement of Ethernet technologies is boosting the eagerness of extending their use to cover factory-floor distributed real time applications. Indeed, it is remarkable the considerable amount of research work that has been devoted to the timing analysis of Ethernet-based technologies in the past few years. It happens, however, that the majority of those works are restricted to the analysis of sub-sets of the overall computing and communication system, thus without addressing timeliness in a holistic fashion. To this end, we address an approach, based on simulation, aiming at extracting temporal properties of commercial-off-the-shelf (COTS) Ethernet-based factory-floor distributed systems. This framework is applied to a specific COTS technology, Ethernet/IP. We reason about the modeling and simulation of Ethernet/IP-based systems, and on the use of statistical analysis techniques to provide useful results on timeliness. The approach is part of a wider framework related to the research project INDEPTH NDustrial-Ethernet ProTocols under Holistic analysis.

Multi-μ: an Ada 95 based architecture for fault tolerance support of real-time systems

This paper presents an architecture (Multi-μ) being implemented to study and develop software based fault tolerant mechanisms for Real-Time Systems, using the Ada language (Ada 95) and Commercial Off-The-Shelf (COTS) components. Several issues regarding fault tolerance are presented and mechanisms to achieve fault tolerance by software active replication in Ada 95 are discussed. The Multi-μ architecture, based on a specifically proposed Fault Tolerance Manager (FTManager), is then described. Finally, some considerations are made about the work being done and essential future developments.