Influencia de la refusion en las propiedades mecanicas y composicion quimica de aleaciones odontologicas

The objective of the study presented in this article was to analyze the influence of remelting of two odontological alloys: Dentorium and Steeldent, on the mechanical properties and on the chemical composition. For the two alloys, samples, containing 10% and 50% new alloy, were subjected to tensile test, micrography and chemical analysis. The alloys presented similar mechanical properties, except for the elongation, which presented higher values for the Dentorium 50% new alloy. This is due to the smaller carbides formed in this sample. The remelting itself seems not to be responsible for these differences, but they are probably due to the lack of a good control of the casting process. The micrography showed a dendritic column matrix, with carbides in the interdentric region and inside dendritic grain. In the chemical composition was observed few elements percentage change.

Control automatico de un sistema electrico mediante logica difusa

Substitution of fuzzy logic control in an electrical system normally controlled by proportional-integral frequency was studied and analyzed. A linear model of an electrical system, the concepts which govern the theory of fuzzy logic, and the application of this theory to systems control, are briefly presented. The methodology of fuzzy logic was then applied to develop a model for an electrical energy system. The results of the simulation demonstrated that fuzzy logic control eliminated the area frequency error and permitted that only the area experiencing an increase in charge responds to this variation. Based on the results, it is concluded that control based on fuzzy logic is simple, is easy to maintain, is of low cost, and can be used to substitute traditional velocity controllers.

Control preventivo dinamico de sistemas de energia electrica usando redespacho de generacion y corte de carga

A model for preventive control in electrical systems is presented, taking into account the dynamic aspects of the network. Among these aspects, the effects provoked by perturbations which cause oscillations in synchronous machine angles (transient stability), such as electric equipment outages and short circuits, are presented. The energy function is used to measure the stability of the system using a procedure defined as the security margin. The control actions employed are load shedding and generation reallocation. An application of the methodology to a system located in southern Brazil, which is composed of 10 synchronous machines, 45 busses, and 72 transmission lines. The results confirm the theoretical studies.

Estudio de la pasivacion de la aleacion Co-Cr-Mo en suero fisiologico

Results are presented on the mechanism of passivation of Co-Cr-Mo biological implant alloys in physiological serum using open circuit potentiometry, potentiodynamic curves, and electrochemical impedance spectroscopy. The potential dependence of impedance data and the analysis of the parameters obtained indicate a progressive diminution of the initial layer thickness and the simultaneous formation of a second higher resistive layer. In more severe conditions than the existent in human body, the metallographic examination of the alloy surface shows localized corrosion in interdendritric regions. Elemental analysis of the surface reveals the presence of higher chromium content in these regions. The presence of chlorine was not detected, which suggested that during preferential attack, soluble species are also formed.

Estudio de viabilidad tecnico-economica para la conversion de hornos electricos en hornos a gas natural

Technical and economic feasibility of using natural gas as a non-polluting energy source was studied. Conversion of electric ovens to gas-fired ovens for the preparation of aluminum plates for laminations was used as an example of this application. Four cases were evaluated for the use of heat derived from residual gases following combustion of the natural gas. Additionally, two possibilities are included for the use of systems of co-generation; one using an internal combustion engine, and second using a gas turbine. Results suggested that it was technically and economically feasible to convert the electric ovens considered to natural gas-operated ovens.

Rectificacion de aceros fragiles y ductiles: Parametros de entrada para obtener los mejores resultados

In this work, the behavior of the steel surface grinding process with conventional grinding wheels was studied for various grinding conditions and a fixed dressing condition. The input parameters (wheel speed, workpiece speed, depth of cut), that set up the grinding conditions were determined as a function of the characteristics of the grinding machine. A test bench was established where the grinding power was measured in real time as a function of the volume of material removed. The results showed that in the grinding of fragile steels with a soft wheel and medium grit size, the average power of the cut shows a tendency to increase and become stabilized. The surface roughness of the piece decreased in all the tests and was proportional to the increase in the number of active grits. In tests on the grinding of ductile steels with a soft wheel and fine grit size, the wheel became dull until the moment that the abrasive grits were released from the cut surface.

Sistema inteligente para la selección de brocas de perforación de pozos

The present work begins with a review of the literature on bit selection methods for oil well drilling. A proposal for the structure and organization of a drilling database and a knowledge base, is described. Previous studies formed the principal elements in the process of selection of drills for proposed drilling. The procedure was implemented as a computer system for the selection of tricone bits. A drilling bit database for three different Brazilian sedimentary basins was obtained for several wells drilled, and knowledge was collected from drilling engineers from different fields both electronically and also by means of interviews. It can be concluded that the selection process showed good results based on tests, which were carried out.

Método multiresiduo para determinar pesticidas en frutas por extracción con fluido supercrítico

A rapid and reliable method for the determination of 25 compounds selected from four classes of pesticides in samples of fresh apples, grapes, pears, and strawberries purchased at a local supermarket, is presented. The study describes two different methods of extraction: solid-liquid extraction with acetone and supercritical fluid extraction. Clean-up was based on aminopropyl cartridge extraction followed by gas chromatography with an electron capture detector for simultaneous determinations. Confirmatory analysis was carried out by gas chromatography with mass spectrometry in the selected-ion monitoring (SIM) mode. Extraction efficiencies were directly compared and the methods were applied to the analysis of real samples. Recoveries for a majority of pesticides from standard samples at enrichment levels of 0.04-0.10 mg/ kg ranged from 77 to 96 % for both methods. The supercritical fluid extraction method showed good limits of detection (less than 0.01 mg/kg, depending on the pesticide and matrix) as well as minimizing environmental concerns, time, and laboratory effort. © 2006 Centro de Información Tecnológica.

Um método de gestão de fornecedores baseado na avaliação da eficácia de auditorias realizadas na fase de desenvolvimento de produtos

The main goal of this work is to present a supplier's management method based on evaluation of audits performed at suppliers during products development phase. Audits are prioritized according to the impact of supplied parts on the development and its main goals are identification of risks, to propose and perform action plans and to evaluate periodically the supplier's performance to prevent problems. It is proposed that if the audits in the development phase be efficient, the supplied products will have good maturity to entry into service and stable performance. This issue was evaluated in a aeronautic company and the analyzed results in 2006 were considered good.

Território e ambiente institutional: O arranjo produtivo local (APL) bordados de Ibitinga-SP

This study shows the importance of the institutional environment in which the local productive arrangements are entered. It shows that the specifics of each case are historical knowledge fundamental to the studies of APLs. It also shows that in areas of traditional sectors with intensive use of labor, low innovative capacity and low barriers to entry, relations that historically will be developing between firms, workers and market can be considered strong constraints of the trajectory of success or failure. The case study is a set of companies producing textiles and confecciones (products of bed, table and bath) located in the municipality of Ibitinga-SP, of great importance in the region, the high generation of employment and income. It is the study of a particular case in the context of studies on local productive arrangements (APLs), because it serves to highlight the importance of the institutional environment as a prerequisite to overcome the difficulties and consolidation of APLs.

Influencia de la separación de residuos sólidos urbanos para reciclaje en el proceso de incineración con generación de energía

This work analyses the recuperation of the energy of Municipal Solid Waste (MSW) through the incineration process. It considers the up to date tendency of segregation (separation) of plastic, paper and cardboard, glass and metals and their influence in the fluxes of mass and energy in the incineration system of MSW. For its development was used information related to the generation of MSW in Bauru city and the Combust software. The results so obtained allowed the estimation of the Caloric power of the typical MSW and also of this residue when one considers the separations of paper/cardboard and plastic for recycling.

Trabalho de docência e comportamento micro-organizacional: A motivação do docente na área da saúde

Using the motivograma and interviews the degree of motivation of the survey participants was defined as satisfactory. On one hand there is satisfaction with the physiological needs, self-esteem and self confidence, on the other there is high dissatisfaction with the association and self-realization, justifying the request for strengthening the membership and performance improvements in the research area. Linking up security and association with the other ones group protection sentiments and work environment dependence sentiments prevail. It was concluded that: (1) Those satisfied ones declare that they are safe, protected and with good self-esteem doing their teaching work. The ones dissatisfied with the non-group belonging demonstrate dissatisfaction with the self-realization and expose their difficulties with social ties and the lack of integration in the teaching work. (3) The degree of motivation satisfactory is related to the satisfaction of basic needs, located in the first steps of Maslow's hierarchy. Accepting that the changes in higher education require motivated behaviors, the question arises: how can the motivation in teaching work be possible if the majority of organizations do not find a way to deal with the person of the Professor? Finally, the context of work is predominant in the provision of job satisfaction in teaching.

Investigación con enfoque de sistemas en la agricultura campesina ecuatoriana

Incluye Bibliografía

La distribucion del ingreso y las situaciones de pobreza

Incluye Bibliografía

Dinâmica regional e política urbana: Uma análise das cidades de porte médio da região administrativa de Campinas/SP

The process of internalization of development occurred in the state of Sao Paulo resulted in accelerated growth of intermediate cities leading to a pattern of development with sprawl, segregation and suburbanization. In this process stands the Administrative Region of Campinas, the hinterland region of higher growth and accumulating a larger number of medium-sized cities. Such questions imply the need for appropriate urban policies to confront these challenges, under risk to jeopardize the quality of life and environment of these cities. The implementation of the Estatuto da Cidade brings new perspectives for urban management in medium-sized cities. This study aims to evaluate the deployment of instruments of urban management in medium-sized cities in São Paulo, with emphasis on Administrative Region of Campinas, based on the Profile of Brazilian Municipalities 2008 conducted by IBGE. The results point to a worrying situation, as it did not see a correlation between the deployment of these instruments and the size, growth and income in the mid-sized cities.