Modelagem de máquina pneumática recolhedora de frutos de café em terreiro usando análise por elementos finitos

Teve-se o objetivo de desenvolver um modelo matemático por meio de análise de elementos finitos, utilizando o programa computacional ANSYS®, versão 5.7, para otimizar o projeto de máquina recolhedora de frutos de café no terreiro. A modelagem da máquina foi realizada com base no levantamento das características aerodinâmicas dos frutos de café e da vazão de ar necessária para o transporte pneumático dos frutos. Foram obtidas, experimentalmente, as pressões estáticas nos dutos da máquina, sendo esses valores comparados com os resultados determinados pelo programa ANSYS, no intuito de validar o modelo. Com base nos resultados numéricos obtidos, concluiu-se que a modelagem desenvolvida apresentou resultados próximos aos determinados experimentalmente, obtendo erro relativo médio nos valores simulados de pressão de 9,2%. Por meio da modelagem, identificaram-se faixas de pressão que dificultariam o transporte pneumático dos frutos de café em alguns pontos da máquina. Esses problemas foram corrigidos e, com isso, o fluxo de ar proporcionado pelo ventilador foi suficiente para succionar os frutos de café no terreiro e transportá-los para dentro do reservatório da máquina. A modelagem desenvolvida atendeu às necessidades propostas no trabalho para o recolhimento dos frutos de café utilizando transporte pneumático eficientemente.

Aplicação de ensaios de resistividade na caracterização do Sistema Aquífero Barreiras / Marituba em Maceió - AL

A caracterização do Sistema Aquífero Barreiras / Marituba, maior fonte de abastecimento de água da cidade de Maceió, capital de Alagoas, Brasil, é importante para fornecer subsídios para uma utilização racional e sustentável desse recurso. O arcabouço tectônico e estratigráfico da área construído por meio de perfis de poços, análise de elementos estruturais e mapeamento geológico propõe um modelo com uma série de grabens e horsts. Com o objetivo de confirmar a presença de estruturas delimitando blocos estruturais e refinar o modelo foram realizados ensaios de sondagem elétrica vertical e caminhamento elétrico dipolo-dipolo. Os resultados dos ensaios geofísicos confirmaram a existência de zonas mais condutoras, que caracterizam as zonas de falhas normais que delimitam os blocos estruturais. A integração dos dados geológicos e estruturais aos resultados geofísicos confirmaram a existência de um modelo estrutural com blocos escalonados, que influenciam fortemente o comportamento do sistema águas subterrâneas.

Ensaios sobre a metodologia do estudo da influência de três herbicidas em Spirodela punctata (G.F.W. Meyer) Thompson (Lemnaceae)

O presente trabalho visa conhecer a taxa de multiplicação e o índice de mortalidade de S. punctata a diversas concentrações do butaclora, propanila e glifosato bem como comparar dois métodos diferentes de investigações (ensaio 1 e 2). Os dados indicaram que no ensaio 1 as concentrações foram pouco tóxicas provocando baixos índices de mortalidade embora tenha ocorrido inibição do crescimento nas concentrações mais fortes. O ensaio 2 mostrou que a butaclora e a propanila são mais tóxicas que o glifosato, com valores de mortalidade de 100% em apenas 48 horas. A taxa de multiplicação, neste ensaio, somente foi determinada para o glifosato, pois os demais herbicidas foram altamente tóxicos para a espécie. Verificou-se, na comparação dos dois métodos diferentes, que os recipientes utilizados no ensaio 2 foram mais adequados ao cultivo da espécie e que os efeitos tóxicos devem ser observados em frondes consideradas individualmente e não em plantas inteiras.

Persistência do plano experimental em ensaios de avaliação de germoplasma elite de feijão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação de recomendações normativas sobre o uso de ensaios no controle de qualidade de fabricação de geossintéticos

A utilização de materiais poliméricos designados por geossintéticos tem aumentando significativamente nos últimos anos na Engenharia Civil. Para desempenhar adequadamente a função para a qual foram projetados, os geossintéticos devem ser submetidos a um rigoroso processo de controle de qualidade durante a fabricação. Discussões sobre a freqüência e os principais tipos de ensaios de laboratório utilizados nesse processo de controle para dois tipos de geossintéticos, os geotêxteis e as geomembranas, os materiais mais utilizados da famíla dos geossintéticos, são abordados no presente trabalho. As análises efetuadas com base em normas disponíveis no Brasil, nos EUA e na Europa mostram que no cenário nacional não há recomendações normativas sobre o controle de qualidade para a maioria das aplicações de geotêxteis e geomembranas, sendo o assunto pouco discutido na literatura técnica. No cenário internacional, as normas Européias se destacam como o conjunto de práticas mais completo para ensaios de controle de qualidade de fabricação, considerando os diversos tipos de aplicação dos geossintéticos na Engenharia Civil.

Localized mechanics of dentin self-etching adhesive system

The bond strength of composite resins (CRs) to dentin is influenced by the interfacial microstructure of the hybrid layer (HL) and the resin tags (TAG). The contemporary self-etching primer adhesive systems overcame the inconvenient of the etch-and-rinse protocol. Studies, however, have demonstrated that HL thickness and TAG length vary according to the wetting time and additional use of acid-etching prior to self-etching primers. This study investigated the localized stress distribution in the HL and the dentin/adhesive interface. Two HL thicknesses (3 or 6 mu m), two TAG lengths (13 or 17 mu m) and two loading conditions (perpendicular and oblique-25 degrees) were investigated by the finite element (FE) analysis. Five two-dimensional FE models (M) of a dentin specimen restored with CR (38 x 64 mu m) were constructed: M1 - no HL and no TAG; M2 - 3 mu m of HL and 13 mu m of TAG; M3 - 3 mu m of HL and 17 mu m of TAG; M4 - 6 mu m of HL and 13 mu m of TAG; and M5 - 6 mu m of HL and 17 mu m of TAG. Two distributed loadings (L) (20N) were applied on CR surface: L1 - perpendicular, and L2 - oblique (25 degrees). Fixed interfacial conditions were assigned on the border of the dentin specimen. Ansys 10.0 (Ansys (R), Houston, PA, USA) software was used to calculate the stress fields. The peak of von Mises (sigma(vM)) and maximum principal stress (sigma(max)) was higher in L2 than in L1. Microstructures (HL and TAG) had no effect on local stresses for L1. Decreasing HL decreased sigma(vM) and sigma(max) in all structures for L2, but the TAG length had influence only on the peributular dentin. The thickness of HL had more influence on the sigma(vM) and sigma(max) than TAG length. The peritubular dentin and its adjacent structures showed the highest sigma(vM) and sigma(max), mainly in the oblique loading.

Numeric evaluation of the stiffness of log-concrete composite beams submitted the cyclical load

In this paper was evaluated, using the software ANSYS, the stiffness (El) of the log-concrete composite beams, of section T, with connectors formed by bonded-in steel rods, type CA-50, disposed in X, with application of cyclical load. The stiffness of the system was evaluated through the simulation of bending tests, considered 1/2 beam, with cyclical shipment varying among 40 % and 5 % of the strength of the connection with the load relationship R=0,125, for a total of 10 load cycles applied. The numeric results show a good agreement with experimental tests.

Ensaios triaxiais dinamicos sobre amostras indeformadas de um solo colapsivel

Tests were carried out with samples from two depths of a vertical soil profile. The results indicate that the permanent deformation characteristics of the soil are dependent on their depth in the vertical profile and on their water content. Some practical consequences to the performance of the pavement were considered.

Analysis of aluminum plates under heating in electrical and natural gas furnaces

This paper analyzes the thermal storage characteristics of aluminum plates in furnaces during their heating for lamination under two sources of heat: an electrical resistance bank and a combustion process carried out with natural gas. The set of equations to model the furnace under operation with electrical energy, for air as the fluid, is presented. This supports the theoretical analysis for the system under operation with natural gas combustion products. A numerical procedure, using the software ANSYS, is applied to determine the convection heat transfer coefficients for heating by the air flow. Temperatures measured in a plate inside a real furnace are used as parameters to determine these coefficients. Then convection and radiation heat transfer coefficients are determined for the natural gas combustion products. Results are compared, indicating a possible gain of 5.5 h in relation to a 19.5 h period of conventional electrical heating per plate.

Avaliação da atividade mutagênica do resíduo sólido de uma fábrica de confecções de meias e lingerie em ensaios com Salmonella typhimurium

Cancer is one of the most hazardous effects to human health caused by the exposition to chemical agents. The search for new technological solutions in the industrial field led to a rapid increase in the productive sector, causing the workers to be exposed to millions of potentially toxic agents, substances potentially harmful to health. This study presents the mutagenic activity of sweepings from a sock and lingerie factory in Araraquara-Brazil, assayed with Salmonella typhimurium. All the extracts from the factory had mutagenic on activity the YG1024 strain, which is extremely sensitive to detect the mutagenic activity of the arilhydroxilamines, nitroarenes and aromatic amines. The extracts were non-mutagenics for the strains TA100 and TA98. The analysis of the mutagenicity of industrial residues is highly important because employees that participate in the production are directly exposed to those agents, as well as to the environment where the garbage is deposited.

Protocolo para ensaios físico-químicos de estabilidade de fitocosméticos

The growing demand for stable, safe and effective cosmetics has required increasingly complex studies by the scientific community and the use of more efficient techniques to determine the stability of these products. The use of active principles from the Brazilian flora has led to the development of numerous products, in the most varied pharmaceutical forms, making it, even more difficult to standardize experimental protocols to certify the stability of cosmetic preparations. While in Brazil there is no one protocol that standardizes the tests that should be carried out to determine product stability, several studies have been conducted in academic laboratories to determine the stability of specific raw materials. The rheological properties of topical use products have to be taken into account in their manufacture, storage and application. The determination of the rheological behavior of a formulation helps in evaluating the physicochemical nature of the vehicle, allowing early signs of physical instability to be detected and thus enabling quality control of the constituents, test formulations and final products. Thermal analysis has also been used to assist in the study of cosmetic stability and differential scanning calorimetry to guide the development of new products. Other tools, such as fluorimetry and laser granulometry can be used to help the study and development of both emulsified and non-emulsified systems. The aim of the present study is to develop a protocol for the investigation of the physical and chemical stability of phytocosmetics - systems containing active compounds extracted from the Brazilian biodiversity.

Ensaios biológicos para avaliação de segurança de produtos cosméticos

Despite efforts to the contrary, some cosmetic products can cause undesirable side effects in the users. These may often be due to individual factors or inappropriate use of the product. Thus, biological assays to assess the safety of a new cosmetic must precede its being placed on the market. Historically, these tests have always been carried out in vivo, in animals, since such tests can be used to evaluate many of the potential risks, such as irritation, allergy or systemic effects; but, recently, some research centers have been adopting in vitro alternatives, in order to replace the animal tests. This review emphasizes the need to employ biological assays to test the safety of cosmetic products, and reviews the main in vivo and in vitro tests used, focusing on the need to develop and use alternatives to the in vivo assays of product safety, so as to offer the consumers the maximum safety with the least possible risk, while ensuring the best conditions of use of the product.

Analysis of mechanical behavior in bending of polymer composites using the finite elements method

The use of composite materials has increased in the recent decades, mainly in the aeronautics and automotives industries. In the present study is elaborated a computational simulation program of the bending test using the finite elements method, in the commercial software ANSYS. This simulation has the objective of analyze the mechanical behavior in bending of two composites with polymeric matrix reinforced with carbon fibers. Also are realized bending tests of the 3 points to obtain the resistances of the materials. Data from simulation and tests are used to make a comparison between two failures criteria, Tsai-Wu and Hashin criterion. Copyright © 2009 SAE International.