Simulation of Boundary Layers and Heat Transfer in the Entrance Region of Pipes

The study of fluid flow in pipes is one of the main topic of interest for engineers in industries. In this thesis, an effort is made to study the boundary layers formed near the wall of the pipe and how it behaves as a resistance to heat transfer. Before few decades, the scientists used to derive the analytical and empirical results by hand as there were limited means available to solve the complex fluid flow phenomena. Due to the increase in technology, now it has been practically possible to understand and analyze the actual fluid flow in any type of geometry. Several methodologies have been used in the past to analyze the boundary layer equations and to derive the expression for heat transfer. An integral relation approach is used for the analytical solution of the boundary layer equations and is compared with the FLUENT simulations for the laminar case. Law of the wall approach is used to derive the empirical correlation between dimensionless numbers and is then compared with the results from FLUENT for the turbulent case. In this thesis, different approaches like analytical, empirical and numerical are compared for the same set of fluid flow equations.

Numerical Modelling of Combustion and Emission Formation in a Diesel Engine with Different Fuel Injection Characteristics

Päästöjen vähentäminen on ollut viime vuosina tärkeässä osassa polttomoottoreita kehitettäessä.Monet viralliset tahot asettavat uusia tiukempia päästörajoituksia. Päästörajatovat tyypillisesti olleet tiukimmat autoteollisuuden valmistamille pienille nopeakäyntisille diesel-moottoreille, mutta viime aikoina paineita on kohdistunut myös suurempiin keskinopeisiin ja hidaskäyntisiin diesel-moottoreihin. Päästörajat ovat erilaisia riippuen moottorin tyypistä, käytetystä polttoaineesta ja paikasta missä moottoria käytetään johtuen erilaisista paikallisista laeista ja asetuksista. Eniten huomiota diesel-moottorin päästöissä täytyy kohdistaa typen oksideihin, savun muodostukseen sekä partikkeleihin. Laskennallisen virtausmekaniikan (CFD) avulla on hyvät mahdollisuudet tutkia diesel-moottorin sylinterissä tapahtuvia ilmiöitä palamisen aikana. CFD on hyödyllinen työkalu arvioitaessa moottorin suorituskykyä ja päästöjen muodostumista. CFD:llä on mahdollista testata erilaisten parametrien ja geometrioiden vaikutusta ilman kalliita moottorinkoeajoja. CFD:tä voidaan käyttää myös opetustarkoituksessa lisäämään paloprosessin tuntemusta. Tulevaisuudessa palamissimuloinnit CFD:llä tulevat epäilemättä olemaan tärkeä osa moottorin kehityksessä. Tässä diplomityössä on tehty palamissimuloinnit kahteen erilaisilla poittoaineenruiskutuslaitteistoilla varustettuun Wärtsilän keskinopeaan diesel-moottoriin. W46 moottorin ruiskutuslaitteisto on perinteinen mekaanisesti ohjattu pumppusuutin ja W46-CR moottorissa on elektronisesti ohjattu 'common rail' ruiskutuslaitteisto. Näiden moottorien ja käytössä olevien ruiskutusprofiilien lisäksi on simuloinneilla testattu erilaisia uusia ruiskutusprofiileja, jotta erityyppisten profiilien hyvät ja huonot ominaisuudet tulisivat selville. Matalalla kuormalla kiinnostuksen kohteena on nokipäästöjen muodostus ja täydellä kuormalla NOx-päästöjen muodostus ja polttoaineen kulutus. Simulointien tulokset osoittivat, että noen muodostusta matalalla kuormalla voidaan selvästi vähentää monivaiheisella ruiskutuksella, jossa yksi ruiskutusjakso jaetaan kahteen tai useampaan jaksoon. Erityisen tehokas noen vähentämisessä vaikuttaa olevan ns. jälkiruiskutus (post injection). Matalat NOx-päästöt ja hyvä polttoaineen kulutus täydellä kuormalla on mahdollista saavuttaaasteittain nostettavalla ruiskutusnopeudella.

Physical Limnology in Lake Banyoles

The main physical long-scale processes occurring in Lake Banyoles are reviewed as a tribute to Prof. Margalef. These processesinclude the water fluxes below the surface of the lake, the behavior of the sediment in suspension in the basins, the heat fluxesat the surface and at the bottom layers, the internal seiching, the formation of a baroclinic current due to differences in coolingbetween the two lobes, the mixing dynamics, the meromictic behavior of some of the basins and the formation and dynamics of hydrothermal plumes

Aspects on Process Engineering in the Finnish Pulp and Paper Industry : Thesis for the Degree of Licentiate in Science of Technology

Process development will be largely driven by the main equipment suppliers. The reason for this development is their ambition to supply complete plants or process systems instead of single pieces of equipment. The pulp and paper companies' interest lies in product development, as their main goal is to create winning brands and effective brand management. Design engineering companies will find their niche in detail engineering based on approved process solutions. Their development work will focus on increasing the efficiency of engineering work. Process design is a content-producing profession, which requires certain special characteristics: creativity, carefulness, the ability to work as a member of a design team according to time schedules and fluency in oral as well as written presentation. In the future, process engineers will increasingly need knowledge of chemistry as well as information and automation technology. Process engineering tools are developing rapidly. At the moment, these tools are good enough for static sizing and balancing, but dynamic simulation tools are not yet good enough for the complicated chemical reactions of pulp and paper chemistry. Dynamic simulation and virtual mill models are used as tools for training the operators. Computational fluid dynamics will certainlygain ground in process design.

Computational Analysis and Optimization of Real Gas Flow In Small Centrifugal Compressors

Small centrifugal compressors are more and more widely used in many industrialsystems because of their higher efficiency and better off-design performance comparing to piston and scroll compressors as while as higher work coefficient perstage than in axial compressors. Higher efficiency is always the aim of the designer of compressors. In the present work, the influence of four partsof a small centrifugal compressor that compresses heavy molecular weight real gas has been investigated in order to achieve higher efficiency. Two parts concern the impeller: tip clearance and the circumferential position of the splitter blade. The other two parts concern the diffuser: the pinch shape and vane shape. Computational fluid dynamics is applied in this study. The Reynolds averaged Navier-Stokes flow solver Finflo is used. The quasi-steady approach is utilized. Chien's k-e turbulence model is used to model the turbulence. A new practical real gas model is presented in this study. The real gas model is easily generated, accuracy controllable and fairly fast. The numerical results and measurements show good agreement. The influence of tip clearance on the performance of a small compressor is obvious. The pressure ratio and efficiency are decreased as the size of tip clearance is increased, while the total enthalpy rise keeps almost constant. The decrement of the pressure ratio and efficiency is larger at higher mass flow rates and smaller at lower mass flow rates. The flow angles at the inlet and outlet of the impeller are increased as the size of tip clearance is increased. The results of the detailed flow field show that leakingflow is the main reason for the performance drop. The secondary flow region becomes larger as the size of tip clearance is increased and the area of the main flow is compressed. The flow uniformity is then decreased. A detailed study shows that the leaking flow rate is higher near the exit of the impeller than that near the inlet of the impeller. Based on this phenomenon, a new partiallyshrouded impeller is used. The impeller is shrouded near the exit of the impeller. The results show that the flow field near the exit of the impeller is greatly changed by the partially shrouded impeller, and better performance is achievedthan with the unshrouded impeller. The loading distribution on the impeller blade and the flow fields in the impeller is changed by moving the splitter of the impeller in circumferential direction. Moving the splitter slightly to the suction side of the long blade can improve the performance of the compressor. The total enthalpy rise is reduced if only the leading edge of the splitter ismoved to the suction side of the long blade. The performance of the compressor is decreased if the blade is bended from the radius direction at the leading edge of the splitter. The total pressure rise and the enthalpy rise of thecompressor are increased if pinch is used at the diffuser inlet. Among the fivedifferent pinch shape configurations, at design and lower mass flow rates the efficiency of a straight line pinch is the highest, while at higher mass flow rate, the efficiency of a concave pinch is the highest. The sharp corner of the pinch is the main reason for the decrease of efficiency and should be avoided. The variation of the flow angles entering the diffuser in spanwise direction is decreased if pinch is applied. A three-dimensional low solidity twisted vaned diffuser is designed to match the flow angles entering the diffuser. The numerical results show that the pressure recovery in the twisted diffuser is higher than in a conventional low solidity vaned diffuser, which also leads to higher efficiency of the twisted diffuser. Investigation of the detailed flow fields shows that the separation at lower mass flow rate in the twisted diffuser is later than in the conventional low solidity vaned diffuser, which leads to a possible wider flow range of the twisted diffuser.

Control and Simulation of Batch Crystallization

Concerning process control of batch cooling crystallization the present work focused on the cooling profile and seeding technique. Secondly, the influence of additives on batch-wise precipitation process was investigated. Moreover, a Computational Fluid Dynamics (CFD) model for simulation of controlled batch cooling crystallization was developed. A novel cooling model to control supersaturation level during batch-wise cooling crystallization was introduced. The crystallization kinetics together with operating conditions, i.e. seed loading, cooling rate and batch time, were taken into account in the model. Especially, the supersaturation- and suspension density- dependent secondary nucleation was included in the model. The interaction between the operating conditions and their influence on the control target, i.e. the constant level of supersaturation, were studied with the aid of a numerical solution for the cooling model. Further, the batch cooling crystallization was simulated with the ideal mixing model and CFD model. The moment transformation of the population balance, together with the mass and heat balances, were solved numerically in the simulation. In order to clarify a relationship betweenthe operating conditions and product sizes, a system chart was developed for anideal mixing condition. The utilization of the system chart to determine the appropriate operating condition to meet a required product size was introduced. With CFD simulation, batch crystallization, operated following a specified coolingmode, was studied in the crystallizers having different geometries and scales. The introduced cooling model and simulation results were verified experimentallyfor potassium dihydrogen phosphate (KDP) and the novelties of the proposed control policies were demonstrated using potassium sulfate by comparing with the published results in the literature. The study on the batch-wise precipitation showed that immiscible additives could promote the agglomeration of a derivative of benzoic acid, which facilitated the filterability of the crystal product.

Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

Comparison of Compound Lean Nozzles and Controlled Flow Nozzles at Off-Design

Turbokoneet ja etenkin höyryturbiinit ovat usein suunniteltu ja optimoitu toimimaan tietyssä toimintapisteessä jossa häviöt on minimoitu ja hyötysuhde maksimoitu. Joissakin tapauksissa on kuitenkin tarpeellista käyttää turbiinia toimintapisteen ulkopuolella. Tällöin turbiinin läpi virtaava massavirta muuttuu ja yleensä heikentää hyötysuhdetta. Turbokoneiden suorituskykyä voidaan parantaa käyttämällä kolmidimensionaalisesti muotoiltuja siipiä. Työssä on vertailtu laskennallisesti kahta kohtuullisesti muotoiltua suutinta (Compound lean ja Controlled flow) niiden suunnitellun toimintapisteen ulkopuolella. Kolmas suutin, ilman kolmidimensionaalista muotoilua on mukana vertailukohteena. Suutinten suorituskykyä tutkitaan laskennallisen virtausmekaniikan avulla olosuhteissa, jotka ovat toimintapisteen ulkopuolella. Virtauksen muutoksia tutkitaan kokonaispainehäviön, isentrooppisen hyötysuhteen ja virtauspinnan yhdenmukaisuuden avulla. Virtauspintoja verrataan ulosvirtauskulman, massavirran ja toisiovirtausvektoreiden jakauman avulla. Erot suutinten suorituskykyvyssä korostavat ylikuormalla. Kun massavirran arvoa on kohotettu eniten, Compound lean suuttimilla hyötysuhde laskee Controlled flow suuttimeen verrattuna vähemmän. Alikuormalla, kun massavirran arvoa lasketaan, erot suuttimien suorituskyvyssä pienenevät ja tutkittujen suuttimien ulosvirtaus on samankaltainen.

Kuristettujen isotermisen vesivirtausten kolmidimensionaalinen mallintaminen

Työssä on tutkittu CFX ja Fluent virtauslaskentaohjelmien soveltavuutta kuristet-tujen isotermisten vesivirtausten kolmidimensionaaliseen mallintamiseen. Teoriaosassa on esitelty virtausta hallitsevat perusyhtälöt sekä eri kavitaatioteori-oita kavitaatiokuplan syntymisestä tuhoutumiseen. Laskennallisessa osassa esitellään käytetyt virtauslaskentaohjelmat ja laskentatapaukset sekä verrataan saatuja tuloksia aiemmin suoritettuihin mittauksiin. Työn pääpaino oli tutkia käytettyjen virtauslaskentaohjelmien soveltuvuutta kuris-tettujen virtauksien mallinnukseen.

CFD study of penetration and mixing of fuel in a circulating fluidized bed furnace

The aim of this thesis is to study the mixing of fuel and, also to some extent, the mixing of air in a circulating fluidized bed boiler. In the literature survey part of this thesis, a review is made of the previous experimental studies related to the fuel and air mixing in the circulating fluidized beds. In the simulation part of it the commercial computational fluid dynamics software (FLUENT) is used with the Eulerian multiphase model for studying the fuel mixing in the two and three-dimensional furnace geometries. The results of the three-dimensional simulations are promising and, therefore suggestions are made for the future simulations. The two-dimensional studies give new information of the effects of the fluidization velocity, fuel particle size and fuel density on the fuel mixing. However, the present results show that three-dimensional models produce more realistic representation of the circulating fluidized bed behavior.

Virtauslaskentaa ja energia-analyysiä hyödyntävä huoneilman lämpöolosuhteiden simulointimalli

Huonetilojen lämpöolosuhteiden hallinta on tärkeä osa talotekniikan suunnittelua. Tavallisesti huonetilan lämpöolosuhteita mallinnetaan menetelmillä, joissa lämpödynamiikkaa lasketaan huoneilmassa yhdessä laskentapisteessä ja rakenteissa seinäkohtaisesti. Tarkastelun kohteena on yleensä vain huoneilman lämpötila. Tämän diplomityön tavoitteena oli kehittää huoneilman lämpöolosuhteiden simulointimalli, jossa rakenteiden lämpödynamiikka lasketaan epästationaarisesti energia-analyysilaskennalla ja huoneilman virtauskenttä mallinnetaan valittuna ajanhetkenä stationaarisesti virtauslaskennalla. Tällöin virtauskentälle saadaan jakaumat suunnittelun kannalta olennaisista suureista, joita tyypillisesti ovat esimerkiksi ilman lämpötila ja nopeus. Simulointimallin laskentatuloksia verrattiin testihuonetiloissa tehtyihin mittauksiin. Tulokset osoittautuivat riittävän tarkoiksi talotekniikan suunnitteluun. Mallilla simuloitiin kaksi huonetilaa, joissa tarvittiin tavallista tarkempaa mallinnusta. Vertailulaskelmia tehtiin eri turbulenssimalleilla, diskretointitarkkuuksilla ja hilatiheyksillä. Simulointitulosten havainnollistamiseksi suunniteltiin asiakastuloste, jossa on esitetty suunnittelun kannalta olennaiset asiat. Simulointimallilla saatiin lisätietoa varsinkin lämpötilakerrostumista, joita tyypillisesti on arvioitu kokemukseen perustuen. Simulointimallin kehityksen taustana käsiteltiin rakennusten sisäilmastoa, lämpöolosuhteita ja laskentamenetelmiä sekä mallinnukseen soveltuvia kaupallisia ohjelmia. Simulointimallilla saadaan entistä tarkempaa ja yksityiskohtaisempaa tietoa lämpöolosuhteiden hallinnan suunnitteluun. Mallin käytön ongelmia ovat vielä virtauslaskennan suuri laskenta-aika, turbulenssin mallinnus, tuloilmalaitteiden reunaehtojen tarkka määritys ja laskennan konvergointi. Kehitetty simulointimalli tarjoaa hyvän perustan virtauslaskenta- ja energia-analyysiohjelmien kehittämiseksi ja yhdistämiseksi käyttäjäystävälliseksi talotekniikan suunnittelutyökaluksi.

Optimizing nozzle flow in laser cutting

The purpose of this study was to investigate different laser cutting nozzles, nozzle flows and possibilities to improve nozzle flow. Another goal was to design new nozzle configuration in which laser cutting would succeed with better cutting speed and smaller gas consumption. Nozzles and nozzle flows were studied with various methods. Computational fluid dynamics was used to calculate old, convergent nozzles and new convergent-divergent nozzles. Measurement apparatus was used to measure both nozzle types. In cutting tests different materials were cut with new nozzles. With the use of design convergent-divergent nozzles 25 % better cutting speed and 33 % smaller gas consumption were achieved when cutting quality was good. Computational fluid dynamics was also discovered to be useful aid in nozzle design.

Large Break Blowdown Test Facility Study

Työn tarkoituksena on kerätä yhteen tiedot kaikista maailmalta löytyvistä ison LOCA:n ulospuhallusvaiheen tutkimiseen käytetyistä koelaitteistoista. Työn tarkoituksena on myös antaa pohjaa päätökselle, onko tarpeellista rakentaa uusi koelaitteisto nesterakenne-vuorovaikutuskoodien laskennan validoimista varten. Ennen varsinaisen koelaitteiston rakentamista olisi tarkoituksenmukaista myös rakentaa pienempi pilottikoelaitteisto, jolla voitaisiin testata käytettäviä mittausmenetelmiä. Sopivaa mittausdataa tarvitaan uusien CFD-koodien ja rakenneanalyysikoodien kytketyn laskennan validoimisessa. Näitä koodeja voidaan käyttää esimerkiksi arvioitaessa reaktorin sisäosien rakenteellista kestävyyttä ison LOCA:n ulospuhallusvaiheen aikana. Raportti keskittyy maailmalta löytyviin koelaitteistoihin, uuden koelaitteiston suunnitteluperusteisiin sekä aiheeseen liittyviin yleisiin asioihin. Raportti ei korvaa olemassa olevia validointimatriiseja, mutta sitä voi käyttää apuna etsittäessä validointitarkoituksiin sopivaa ison LOCA:n ulospuhallusvaiheen koelaitteistoa.

Lifetime enhancement of scroll rings by spatiotemporal fluctuations

The dynamics of three-dimensional scroll rings with spatiotemporal random excitability is investigated numerically using the FitzHugh-Nagumo model. Depending on the correlation time and length scales of the fluctuations, the lifetime of the ring filament is enlarged and a resonance effect between the time scale of the scroll ring and the time correlation of the noise is observed. Numerical results are interpreted in terms of a simplified stochastic model derived from the kinematical equations for three-dimensional excitable waves.

Lifetime enhancement of scroll rings by spatiotemporal fluctuations

The dynamics of three-dimensional scroll rings with spatiotemporal random excitability is investigated numerically using the FitzHugh-Nagumo model. Depending on the correlation time and length scales of the fluctuations, the lifetime of the ring filament is enlarged and a resonance effect between the time scale of the scroll ring and the time correlation of the noise is observed. Numerical results are interpreted in terms of a simplified stochastic model derived from the kinematical equations for three-dimensional excitable waves.