Post-depositional modification of atmospheric dust on a granite building in central Rio de Janeiro: implications for surface induration and subsequent stone decay

Extensive contour scaling of a 200 year old granite church is associated with the breaching of an apparently iron-rich crust and the widespread deposition of atmospheric dust within the canyon-like streetscape of Rio de Janeiro. Contemporary dust, accumulated dust from within the a depression on the building surface, the surface crust and the underlying granite are examined by a combination of total element analysis and sequential extraction, X-ray diffraction and energy dispersive X-ray fluorescence. Results indicate an increase in total organic carbon and a marked decrease in pH within the accumulated dust, and a rapid mobilization of anions and cations from the water-soluble and carbonate phases. It is considered that the latter is linked to salt accumulation within and eventual salt weathering of the granite. Post-depositional alteration of the dust is also linked with the de-silicification of clay minerals (Illite to kaolinite) and the loss of silica from the amorphous Fe/Mn phase of the accumulated dust under the initially saline and progressively more acidic conditions experienced at the stone - atmosphere interface. This mobilization of silica is associated with the formation of what is, in effect, a thin silica-rich surface crust or glaze. Within the glaze, assessory amounts of extractable iron are concentrated within the amorphous and crystalline Fe/Mn phases at levels that are significantly elevated with respect to the underlying granite, but much lower than the equivalent phases of the accumulated dust from which it is principally assumed to derive. The protection afforded to the stone work by the crust is not, however, permanent and within the last 15 years it has been possible to observe a rapid increase in the surface delamination of the church close to street level.

Heterogeneous mixed-layer clays from the Cretaceous greensand, Isle of Wight, southern England

The sea-cliffs of the Isle of Wight were deposited during a period of overall sea-level rise starting in the Barremian (Lower Cretaceous) and continuing into the Aptian and Albian. They consist of fluvial, coastal and lagoonal sediments including greensands and clays. Numerous episodes of erosion, deposition and faunal colonization reflect condensation and abandonment of surfaces with firmgrounds and hardgrounds. This study focused mainly on shallow marine cycles where variations in clay mineralogy would not be expected, because overall system composition, sediment source, and thermal history are similar for all the samples in the studied section. Instead we found a wide variety of clay assemblages even in single samples within a 200 in interval.

Effect of heating vermiculites on extractability of phosphorus and some essential plant micronutrients

The study assessed the effect of heating vermiculites on extractability of phosphorus, iron, zinc and manganese with respect to their potential agricultural use. Of these elements, phosphorus was from apatite and monazite that occur as accessory minerals in vermiculites. Vermiculites were heated at 15-800 degrees C and digested by acetic acid for extracting phosphorus and diethylene triamine pentaacetic acid (DTPA) for extracting zinc, iron and manganese. Phosphorus in the extract was analysed by a flow injection method while zinc, iron and manganese were measured by atomic absorption spectrometry. The results showed that heating vermiculites to 400 C enhanced extractability of phosphorus from apatite and monazite to a level of 335 mg kg(-1). Further heating to 800 degrees C reduced extractable phosphorus to less than 75 mg kg(-1). Maximum extractable zinc, iron and manganese found were 2.7, 19.1 and 22.9 mg kg(-1), respectively, values that are beneficial and tolerable by most plants. Thus, it was concluded that heating vermiculites to

Mineralogical and chemical characterization of some vermiculites from the mozambique belt of tanzania for agricultural use

Vermiculite minerals are locally available in the Mozambique Belt of Tanzania but are not currently commercially exploited. In part this may be due to lack of any precise characterization. This study was carried out as a first step to assess the suitability of these vermiculites for crop production by characterization of their mineralogical and chemical compositions. X-ray diffraction and scanning electron microscopy combined with an energydispersive X-ray system were used to establish the mineralogy. Electron microprobe analysis and inductively coupled plasma-mass spectrometry were used to study the chemical compositions and to identify any possible issues related to chemical composition that might affect their use if applied as soil conditioners. The samples were characterized as vermiculites and hydrobiotites with a wide variety of accessory minerals. Accessory minerals that might be of some concern are galena, fibrous amphiboles and sepiolite. The total levels of Ni in all vermiculites, and Cr in some, were also found to be high relative to common European standards and this might limit their potential as soil conditioners. It is clear that a field assessment of the bioavailability of various elements would be necessary before decisions relating to potential agricultural use could be made. © 2009 The Mineralogical Society.

Matérias-primas da plataforma do Mondego para cerâmica

O presente trabalho divulga os resultados dos estudos levados a efeito nas matérias-primas argilosas que se integram tipologicamente na argila comum, ocorrentes na designada Plataforma do Mondego, Centro de Portugal, na região entre Miranda do Corvo, a SW, e Tábua, a NE. Para tal realizou-se a cartografia superficial dos sedimentos continentais do Cretácico e do Terciário, aí preservados, estabeleceram-se as colunas sedimentares, a nível regional e a nível local, nas áreas de maior potencial reconhecido e, caracterizaram-se as matérias-primas argilosas amostradas, em termos de composição, textura e aptidão cerâmica, objectivando a definição das zonas das jazidas com maior interesse industrial. A informação obtida e compilada, relativa ao caulino e ao feldspato é também apresentada, com vista a uma percepção da potencialidade destas matériasprimas cerâmicas ocorrentes na área. O estudo de caracterização dos materiais argilosos investigados teve como base 53 amostras obtidas em seis regiões da Plataforma do Mondego aqui definidas por motivo de organização do trabalho, segundo os critérios geográfico e geotectónico. As formações de Côja e de Campelo, do Terciário, constituem as unidades onde ocorrem litótipos produtivos, em termos de matéria-prima para a Cerâmica de Barro Vermelho ou Cerâmica de Construção. Relativamente às características texturais e composicionais, em síntese, apresentam-se os factos relevantes seguintes: A matéria-prima argilosa existente na área estudada materializa, granulometricamente, na maioria das amostras, silte, caindo os níveis amostrados com maior percentagem de argila, no domínio do silte argiloso. O défice em fracção argila implica limitações quanto à possibilidade de diversificação de produtos cerâmicos fabricados com estas matérias-primas tal-qual. Os diferentes métodos analíticos utilizados na caracterização mineralógica dos materiais amostrados confirmaram uma composição em termos dos minerais argilosos, consistindo de ilite/mica (em geral, o mais abundante), caulinite e esmectite, interestratificados e clorite. Os minerais não argilosos são quartzo (predominante), feldspato (sobretudo potássico) e hematite, com uma representação baixa. A mineralogia da fracção inferior a 2μm das amostras, não difere das amostras totais, salvo no teor mais elevado dos minerais argilosos e acentuada redução dos minerais não argilosos. Os resultados da análise química por fluorescência de raios X das amostras integrais correlacionam-se com as características mineralógicas observadas através das técnicas analíticas utilizadas. No respeitante às propriedades e comportamento cerâmico verifica-se: Os parâmetros relacionados com a plasticidade indicam que parte das pastas elaboradas com estes materiais argilosos têm uma trabalhabilidade aceitável, mas existem problemas de conformação e acentuada retracção num número significativo de amostras, devido à elevada plasticidade da maioria das amostras. A extrusão é satisfatória a óptima. A RMF e a retracção em seco assumem valores, respectivamente, moderados a baixos e moderados, embora seja necessário ter em conta o procedimento de extrusão dos provetes, sem dispositivo de vácuo. Todas as amostras foram sujeitas a cozedura a 900ºC, e um conjunto seleccionado foi cozido a 1000ºC e a 1100ºC. As fases mineralógicas ocorrentes após cozeduras a 900ºC e 1100ºC foram identificadas num conjunto de amostras, tendo-se evidenciado a coerência dessas fases, com a mineralogia das amostras em seco. Após cozedura a 900ºC, os valores de RMF das amostras satisfazem geralmente os valores mínimos, exigidos para o fabrico de tijolo, abobadilha e, com alguma frequência, de telha, como já se verificava com os valores daquela propriedade em seco. Os valores de retracção seco-cozido são em geral, modestos. A capacidade de absorção de água é maioritariamente elevada. A formação de vidro, sobretudo, condiciona o comportamento destas propriedades por cozedura dos provetes a 1000ºC e a 1100ºC. A coloração predominante em cru das matérias-primas argilosas amostradas é amarelo acastanhado a castanho avermelhado. Após cozedura a 900ºC, há um acentuado escurecimento e incremento no grau de vermelho. As cozeduras a 1000ºC e 1100ºC promovem escurecimento gradual, com ligeira influência na cor. O comportamento dos provetes após as cozeduras cerâmicas revelou-se homogéneo a cada uma das respectivas temperaturas, não se registando também defeitos significativos, nem eflorescências. A análise das amostras em termos composicionais e tecnológicos permitiu destacar as principais características e aspectos distintivos das matériasprimas, nas diferentes regiões definidas objectivando as diferentes potencialidades cerâmicas. Nesta abordagem comparativa foram consideradas só as amostras dos campos silte e silte arenoso, por serem aquelas com maior interesse para a Cerâmica de Construção. Nas colunas sedimentares das regiões de Tábua e Santa Quitéria constata-se a ocorrência de dois ritmos de sedimentação, que embora assumam características específicas em cada região, têm aspectos composicionais e tecnológicos em comum, traduzindo melhor aptidão cerâmica os ritmos inferiores. A conjugação da cartografia realizada com os estudos laboratoriais permite concluir que as regiões de Tábua e de Santa Quitéria serão as que têm maior potencial por explorar, em matéria-prima para Cerâmica de Construção, apesar da primeira já ser intensamente explorada. Na região de Tábua, as amostras têm como fases mineralógicas principais ilite e quartzo na mesma proporção média (35%) e caulinite (média=19%) que regista enriquecimento significativo na fracção argila (média=38%). As argilas desta região registam a cor em cru mais vermelha e pH mais ácido observados. O ritmo de sedimentação inferior, com esmectite e interestratificados e ligeiramente menos quartzoso, apresenta melhores propriedades cerâmicas. A composição mineralógica média das amostras da região de Santa Quitéria é próxima daquela da região de Tábua, mas menos caulinítica, em especial na sequência inferior, na qual o teor médio de caulinite na fracção argila (7%) é o mais baixo observado. Na região de Côja – Arganil, a actividade extractiva é significativa na bacia de Côja. Aqui, a exploração de novas áreas potenciais é condicionada pela cobertura conglomerática e por estruturas tectónicas e não tectónicas relacionadas com comportamento plástico. Na restante área desta região, os recursos argilosos são penalizados por material areno-conglomerático. As amostras desta região distinguem-se das restantes a nível textural pela maior fracção areia e mineralogicamente pela presença de clorite, teor reduzido de caulinite e elevado de feldspato. As potencialidades em barro vermelho na região de Sanguinheda não serão significativas, pois a Formação de Côja é predominantemente arcósica e a Formação de Campelo pouco espessa e conglomerática. As argilas com melhor aptidão cerâmica foram amostradas na região de Miranda do Corvo – Lousã. Na composição, estas amostras são as que contêm maior fracção de argila, maior teor de ilite e caulinite e menor de argilas expansivas. Registam os melhores valores nas características tecnológicas, nomeadamente a RMF e absorção de água. A consistência dos grupos amostrais e ritmos definidos em termos composicionais e tecnológicos é corroborada pelas técnicas de análise estatística multivariada aplicadas, que os identificam. As condições de amostragem na região de Tábua, permitiram a elaboração de uma coluna tipológica, na qual, a partir de uma caracterização expedita de amostras é possível identificar a sua afinidade com os ritmos argilosos definidos e, consequentemente, a sua situação na coluna sedimentar regional e aptidão cerâmica. A cartografia dos recursos argilosos potenciais, elaborada à escala 1:25.000, constitui um dos objectivos principais deste trabalho e nela constam unidades litológicas, nas quais são diferenciadas unidades argilosas tendo também em consideração a tipologia e guias mineralógicos resultantes da caracterização das amostras. As características composicionais destas unidades denotam diferente aptidão cerâmica e, portanto, permitem salientar as zonas com maior interesse económico.

Portuguese georesources suitability for medical hydrology applications

In Portugal, there is an old tradition in using clayey materials for therapeutic purposes. They are applied in pelotherapy, at several beaches of the Atlantic coast in the form of clay-sea water mixtures (peloids) to treat skin and rheumatic diseases. During many generations, peloids have been applied without scienti c studies that prove their therapeutic validity. In the last decade, the Portuguese scienti c community has become increasingly more interested in assessing the properties that make clayey materials suitable for therapeutic purposes. The abundance of clayey formations and the established practices of medical hydrology in our country turned this interest into a new perspective of application. The studied materials include di erent clays (in age and origin) mainly collected from well-known Mesozoic-Cenozoic formations, in some cases outcropping at beaches where empirical applications occur. This thesis focus in the study of silt-clay fraction (< 63 m).To determine their suitability for therapy, compositional, physicochemical, technological, thermal and rheological properties were assessed. Conventional techniques (XRD, XRF and Sedigraph) were used to assess compositional features of silt-clay fraction. Electron microscopy (SEM, VPSEM, HREM) was used to study the micromorphology and composition of clay fraction (< 2 m). Physicochemical properties (cation exchange and speci c surface) were assessed using the Ammonium Acetate and BET methods. Technological properties (plasticity and abrasivity indices) were assessed using the Atterberg limits and Einlehner abrasion tests. Thermal properties (speci c heat and cooling kinetics) were estimated by DSC analysis and cooling tests. Pharmacotechnical tests (compressibility index, sediment volume and Brook eld viscosity) were used to assess the powder owability as well as the physical stability and viscosity of clay-water dispersions. We selected as suitable Portuguese clays for health applications the samples A-Pe, A-Be2, A-Sd, J-Fr , M-To, C-Lu1, C-Lu2, Pl-Ba, M-Ga and J-Ab because they represent safe materials, with an adequate composition, good technological, physicochemical and thermal properties for application, also presenting an adequate rheology when dispersed in water. Their most relevant characteristics are the high clay minerals content, abundant smectite, illite and kaolinite, and safe hazardous concentrations. They also showed moderate capacity to exchange Ca 2+, high plasticity, low abrasivity, high speci c heat and slow cooling kinetics. They evidenced fair powder owability and good potential to formulate viscous dispersions when stabilized. Because the majority of the assessed characteristics are in accordance with those presented by clays applied in European spas for pelotherapy, we considered this group of clays also suitable for medical hydrology treatments in Portuguese spas.

Paleoalterações e cimentações nos depósitos continentais terciários de Portugal central: importância na interpretação de processos antigos

This paper describes the palaeoweathering, cementation, clay minerals association and other closely related characteristics of central Portugal allostratigraphic Tertiary units (SLD's), that can be used for palaeoclimatic interpretation and palaeoenvironmental reconstruction. Lateral and vertical changes in palaeosols are of value for improving our understanding of the autocyclic and allocyclic controls on sediment acumulation in an alluvial basin, but they can also have stratigraphic importance. In some cases it is concluded that the geomorphological setting may have been more decisive than climatic conditions to the production of the palaeoweathering. During late Palaeogene (SLD7-8), surface and near-surface silicification were developed on tectonically stable land surfaces of minimal local relief under a semi-arid climate; groundwater flow was responsible for some eodiagenesis calcareous accumulations, with the neoformation of palygorskite. Conditions during the Miocene (SLD9-11) were favourable for the smectization of the metamorphic basement and arenization of granites. Intense rubefaction associated with basement conversion into clay (illite and kaolinite), is ascribed to internal drainage during late Messinian-Zanclean (SLD12). During Piacenzian (SLD13) intense kaolinization and hydromorphism are typical, reflecting a more humid and hot temperate climate and important Atlantic fluvial drainage. Later on (Gelasian-early Pleistocene ?; SLD14). more cold and dry conditicns are interpreted, at the beginning of the fluvial incision sage. Silica cementation is identified in the upper Eocence-Oligocene ? (SLD18; the major period of silicification), middle to upper Miocene (SLD10)and upper Tortonian-Messinian (SLD11); these occurrences are compatible with either arid or semi-arid conditions and the establishment of a flat landscape upon which a silcrete was developed.

Development of hypogene and supergene alteration and copper mineralization patterns, Sar Cheshmeh porphyry copper deposits, Iran /

The formation of the Sar Cheshmeh porphyry Cu-Mo deposit is related to the culmination of calc-alkaline igneous activity in the Kerman region. The deposit comprises a suite of Late Cenozoic intrusive sub-volcanic and extrusive rocks emplaced into a folded series of Eocene andesitic lavas and pyroclastic sediments. The earliest stage of magmatism was emplacement of a large granodiorite stock about 29 m.y.b.p. This was followed by intrusion of two separate porphyritic bodies at 15 (Sar Cheshrneh porphyry) and 12 m.y.b.p. (Late porphyry) and a series of sub-volcanic dikes between 12 and 9 m.y.b.p. Magmatic activity terminated with multi-phase extrusion of a Pelean dacitic dome complex between 10 and 2.8 m.y.b.p. The country rocks and the earlier porphyritic intrusions are pervasively altered to biotite-rich potassium silicate (metasomatic and hydrothermal) sericite-clay, phyllic and chlorite-clay, argillic assemblages. These grade outwards to an extensive propylitic zone. Within the ore body, the later intra-. and post-mineral dikes only reach the propylitic grade. At least three different sets of quartz veins are present, including a sericite-chlorite-quartz set which locally retrogrades pervasive secondary biotite to sericite. In the hypogene zone, metasomatic and hydrothermal alteration is related to all stages of magmatism but copper mineralization and veining are restricted to a period of 15 to 9 m.y.b.p.related to the early intrusive phases. The copper mineralization and silicate alteration do not fit a simple annular ring model but have been greatly modified by, 1. The existence of an ititial, outer ring, of metasomatic alteration overprinted by an inner.ring of hydrothermal alteration and, 2. later extensive dilating effects of intra- and post-mineral dikes. The hydrothermal clay mineral assemblage in the hypogene zone is illite-chlorite-kaolinite-smectite (beidellite). Preliminary studies indicate that the amount of each of these clays varies vertically and that hydrothermal zonation of clay minerals is possible. However, these minerals alter to illite-kaolinite assemblages in the supergene sulfide zone and to more kaolinite-rich assemblages in the supergene leached zone. Hydrothermal biotite breaks down readily in the supergene zone and is not well preserved in surface outcrops. The distribution of copper minerals in the supergene sulfide enrichment zone is only partly related to rock type being more dependent on topography and the availability of fractures.

Genesis and distribution of Mississippi Valley-type ore assemblages in Middle Silurian strata, Niagara Peninsula, Ontario /

Presently non-commercial occurrences of Mississippi Valley-type ore assemblages in the Middle Silurian strata of the Niagara Peninsula have been studied. Based on this detailed study, a new poly-stage genetic model is proposed which relates ore mineralization in carbonate environments to the evolution of the sedimentary basin. Sulphide ore mineralization occurred during two episodes: 1. During the late diagenesis stage, which is characterized by compaction-maturation of the sediments, the initial mineralization took place by upward and outward movement of connate waters. Metals were probably supplied from all the sediments regardless of their specific lithologies. However, clay minerals were possibly the main contributors. The possible source of sulphur was from petroleum-type hydrocarbons presently mixed with the sediments at the site of ore deposition. Evidence for this is the fact that the greatest abundance of ore minerals is in petroliferous carbonates. The hydrocarbons probably represent liquids remaining after upward migration to the overlying Guelph-Salina reservoirs. The majority of sphalerite and galena formed during this period, as well as accessory pyrite, marcasite, chalcopyrite, chalcocite, arsenopyrite, and pyrrhotite; and secondary dolomite, calcite, celestite, and gypsum. 2. During the presently ongoing surface erosion and weathering phase, which is marked by the downward movement of groundwater, preexisting sulphides were probably remobilized, and trace amounts of lead and zinc were leached from the host material, by groundwaters. Metal sulphides precipitated at, or below, the water table, or where atmospheric oxygen could raise the Eh of groundwaters to the point where soluble metal complexes are unstable and native sulphur co-precipitates with sphalerite and galena. This process, which can be observed today, also results in the transport and deposition of the host rock material. Breakdown of pre-existing sulphide and sulphate, as well as hydrocarbon present in the host rock, provided sulphur necessary for sulphide precipitation. The galena and sphalerite are accompanied by dolomite, calcite, gypsum, anglesite, native sulphur and possibly zincite.

Optical and Thermal Characterization of Dye Intercalated Montmorillonites and Rare Earth Doped Materials

Nondestructive photothermal methods as well as optical absorption and fluorescence spectroscopy are utilized to characterise three different materials, both thermally and optically. The possibility of using montmorillonite clay minerals, after textile waste-water treatment, is investigated for further applications. The laser induced luminescence studies and thermal characterisation of certain rare earth titanates prepared by self propagating high temperature synthesis method are also presented. Moreover, effort is made to characterise rare earth doped sol gel silica glasses with the help of these nondestructive techniques.

Characterisation and Distribution of Amino Acids in the Mangrove Sediments of Kochi

Mangrove swamps are unique inter-tidal wetland ecosystems found in sheltered tropical and subtropical shores.Mangrove sediments can be considered as large reservoirs of amino acids,which exist in several different forms,like free amino acids in the sediment micropores,as amino acids,peptides or proteins bound to clay minerals or as amino acids,peptides or proteins bound to humic colloids.Inorder to assess survival conditions of organisms of mangroves,it is important to understand stability of amino acids in the sediments.The amounts of amino acids present in sediment represent a balance between its synthesis and destruction by microorganisms.Thus amino acid analysis offers more insight into the processes of diagenesis,which changes the nature and characteristics of organic matter deposition and decomposition.

Optical and thermal characterization of dye intercalated montmorillonites and rare earth doped materials

The advent of high optical quality transparent nano—structured glasses, the so-called transparent glass ceramics or vitroceramics disclosed the possibility of producing nano-sized photonic devices based on rare-earth doped up—converters. Transparent glass ceramics have been investigated as hosts for lanthanide ions envisioning the production of materials that are easy to shape and with high performance for photonic applications. Rare earth doped glasses have been extensively studied due to their potential applications in optical devices such as solid state lasers and optical fibers. Various photothermal and optical techniques have been successfully applied for the thermal and optical characterization of these rare earth doped materials. In the present thesis, the effective thermal parameters like thermal diffusivity and thermal effusivity of complex materials for various applications have been investigated using photothermal methods along with their optical characterization utilising the common optical absorption as well as fluorescence spectroscopic techniques. These sensitive optical procedures are also essential for exploiting these materials for further photonic applications.

Studies on the mineralogy, geochemistry and origin of the modern sediments of the ashtamudy lake, Kerala

This study enfolds the environment of deposition and the lateral variation in texture, mineralogy and geochemistry of the Ashtamudy lake sediments. While the heavy mineral and clay mineral investigations enable us to decipher the nature, texture and source of sediments; organic matter and carbonate contents and the geochemical analysis of major and minor elements help establish the distribution and concentration of the same in regard to the various physico-chemical processes operating in the lake. Study of trace elements holds prime importance in this work, since their concentrations can be used to outline the extent of contaminated bottom area, as well as the source and dispersal paths of discharged_pollutants. In short, this study brings out a vivid picture of the mineralogy and geochemistry of the lake sediments in different environments, viz., the freshwater, brackish water and marine environments that are confined to the eastern, central and western parts of the lake respectively. For the better understanding and expression of the results of the analysis, the lake has been divided into 3 zones namely: eastern part, central part and western part.

Sedimentology and Geochemistry of core sediments from the Ashtamudi estuary and the adjoining coastal plain,central Kerala,India

The evolution of coast through geological time scale is dependent on the transgression-regression event subsequent to the rise or fall of sea level. This event is accounted by investigation of the vertical sediment deposition patterns and their interrelationship for paleo-enviornmental reconstruction. Different methods like sedimentological (grain size and micro-morphological) and geochemical (elemental relationship) analyses as well as radiocarbon dating are generally used to decipher the sea level changes and paleoclimatic conditions of the Quaternary sediment sequence. For the Indian coast with a coastline length of about 7500 km, studies on geological and geomorphological signatures of sea level changes during the Quaternary were reported in general by researchers during the last two decades. However, for the southwest coast of India particularily Kerala which is famous for its coastal landforms comprising of estuaries, lagoons, backwaters, coastal plains, cliffs and barrier beaches, studies pertaining to the marine transgression-regression events in the southern region are limited. The Neendakara-Kayamkulam coastal stretch in central Kerala where the coast is manifested with shore parallel Kayamkulam Lagoon on one side and shore perpendicular Ashtamudi Estuary on the other side indicating existence of an uplifted prograded coastal margin followed by barrier beaches, backwater channels, ridge and runnel topography is an ideal site for studying such events. Hence the present study has been taken up in this context to address the gap area. The location for collection of core samples representing coastal plain, estuarylagoon and offshore regions have been identified based on published literature and available sedimentary records. The objectives of the research work are:  To study the lithological variations and depositional environments of sediment cores along the coastal plain, estuary-lagoon and offshore regions between Kollam and Kayamkulam in the central Kerala coast  To study the transportation and diagenetic history of sediments in the area  To investigate the geochemical characterization of sediments and to elucidate the source-sink relationship  To understand the marine transgression-regression events and to propose a conceptual model for the region The thesis comprises of 8 chapters. The first chapter embodies the preamble for the selection and significance of this research work. The study area is introduced with details on its physiographical, geological, geomorphological, rainfall and climate information. A review of literature, compiling the research on different aspects such as physico-chemical, geomorphological, tectonics, transgression-regression events are presented in the second chapter and they are broadly classified into three viz:- International, National and Kerala. The field data collection and laboratory analyses adopted in the research work are discussed in the third chapter. For collection of sediment core samples from the coastal plains, rotary drilling method was employed whereas for the estuary-lagoon and offshore locations the gravity/piston corer method was adopted. The collected subsurficial samples were analysed for texture, surface micro-texture, elemental analysis, XRD and radiocarbon dating techniques for age determination. The fourth chapter deals with the textural analysis of the core samples collected from various predefined locations of the study area. The result reveals that the Ashtamudi Estuary is composed of silty clay to clayey type of sediments whereas offshore cores are carpeted with silty clay to relict sand. Investigation of the source of sediments deposited in the coastal plain located on either side of the estuary indicates the dominance of terrigenous to marine origin in the southern region whereas it is predominantly of marine origin towards the north. Further the hydrodynamic conditions as well as the depositional enviornment of the sediment cores are elucidated based on statistical parameters that decipher the deposition pattern at various locations viz., coastal plain (open to closed basin), Ashtamudi Estuary (partially open to restricted estuary to closed basin) and offshore (open channel). The intensity of clay minerals is also discussed. From the results of radiocarbon dating the sediment depositional environments were deciphered.The results of the microtextural study of sediment samples (quartz grains) using Scanning Electron Microscope (SEM) are presented in the fifth chapter. These results throw light on the processes of transport and diagenetic history of the detrital sediments. Based on the lithological variations, selected quartz grains of different environments were also analysed. The study indicates that the southern coastal plain sediments were transported and deposited mechanically under fluvial environment followed by diagenesis under prolonged marine incursion. But in the case of the northern coastal plain, the sediments were transported and deposited under littoral environment indicating the dominance of marine incursion through mechanical as well as chemical processes. The quartz grains of the Ashtamudi Estuary indicate fluvial origin. The surface texture features of the offshore sediments suggest that the quartz grains are of littoral origin and represent the relict beach deposits. The geochemical characterisation of sediment cores based on geochemical classification, sediment maturity, palaeo-weathering and provenance in different environments are discussed in the sixth chapter. In the seventh chapter the integration of multiproxies data along with radiocarbon dates are presented and finally evolution and depositional history based on transgression–regression events is deciphered. The eighth chapter summarizes the major findings and conclusions of the study with recommendation for future work.