Effect of acetylation on the properties of corn starch

Acetylated corn starches with different degrees of substitution (DS 0.85, DS 1.78, DS 2.89) were synthesized by the reaction of corn starch with acetic anhydride in the presence of acetic acid under varying reaction temperatures. The product was characterized by FTIR spectroscopy, H-1 NMR, X-ray diffraction and contact angle measurement. Acid-base titration and H-1 NMR methods were employed to determine the degree of substitution of product. FTIR spectroscopic analysis showed that the characteristic absorption intensities of esterified starch increased with increase in the degree of substitution, and the characterized peak of hydroxyl group almost disappeared in the spectrum of DS 2.89 acetylated starch. The detailed chemical microstructure of native starch and acetylated starch was confirmed by H-1 NMR, C-13 NMR and C-13-(1) H-1 COSY spectra.

Hot-corrosion behaviors of overlay-clad yttria-stabilized zirconia coatings in contact with vanadate-sulfate salts

A dense clad overlay with chemical inertness was achieved on top of the plasma-sprayed YSZ thermal barrier coatings by laser in order to protect them from hot-corrosion attack. The Al2O3-clad YSZ coating exhibited good hot-corrosion behavior in contact with salt mixture of vanadium pentoxide (V2O5) and sodium sulfate (Na2SO4) for a longtime of 100 h at 1173 K. The LaPO4-clad YSZ coating showed corrosion resistance inferior to the Al2O3-clad one. Yttria was leached from YSZ by reaction between Y2O3 and V2O5, which caused progressive destabilization transformation of YSZ from tetragonal (t) to monoclinic (m) phase. The chemical inertness of the clad layers and the restrained infiltration of the molten corrosive salts by the dense clad layers were primary contributions to improvement of the hot-corrosion resistances.

Rim instability by solvent-induced dewetting

We study the condition of the occurrence of the rim instability in the solvent-induced dewetting process. Our experimental results show that the film thickness not only greatly influences the occurrence of the rim instability, but also influences the wavelength lambda as characterized by the undulation of the deformed contact line. The molecular weight of polymer does not almost influence the occurrence of the rim instability and the wavelength lambda. The wavelength lambda is proportional to the width of the rim in the rim instability region. The receding contact angle theta of polymer solutions on substrates in the dewetting process is an important factor to influence the rim instability in the solvent-induced dewetting.

Critical surface tension of acrylamide-grafted polypropylene copolymer by the contact angle method

The contact angles theta of polar liquids on PP-g-AM copolymer (AM content 0.19, 0.26, and 0.37 wt%) were measured. The critical surface tension gamma(c) of PP-g-AM films were evaluated by the Zisman plot (cos theta versus gamma(L)), the Young-Dupre-Good-Girifalco plot (1 + cos theta) versus 1/gamma(L)(0.5), and the log(1 + cos theta) versus log gamma(L) plot. The gamma(L) values estimated by the plot log(1 + cos theta) versus log gamma(L) were smaller than those obtained by the other plots.

The determination of ethylene-propylene copolymer-grafted-glycidyl methacrylate by the contact angle method

The contact angles theta of some liquids on ethylene-propylene copolymer-grafted-glycidyl methacrylate (EPM-g-GMA) were measured. The critical surface tensions r(c) of EPM-g-GMA were evaluated by the Zisman Plot (cos theta versus r(L)), Young-Dupre-Good-Girifalco plot (1 + cos theta versus 1/r(L)(0.5)) and log (1 + cos theta) versus log(r(L)) plot. The following results were obtained: the r(c) values varied significantly with the estimation methods. The critical surface tension r(c) decreased with the increase of the degree of grafting of EPM-g-GMA.

Thermal conductivity of graded spherical composites with contact resistance

The effective thermal conductivity of graded composites with contact resistance on the inclusion surface is investigated. As an example, we have considered the graded composite media with a spherical particle embedded in a homogeneous matrix, where the thermal conductivity of spherical inclusion is an exponential function k(i) = c exp(betar) (where r is the inside distance of a point in particle from the center of the spherical particle in a spherical coordinate). For both heat contact resistance and perfect contact cases, we have given a reasonable effective medium approximation to calculate the effective conductivity. (C) 2003 Elsevier B.V. All rights reserved.

Effective thermal conductivity of graded nonlinear composites with heat contact resistance

The perturbation expansion method is used to find the effective thermal conductivity of graded nonlinear composites having thermal contact resistance on the inclusion surface. As an example, we have studied the graded composites with cylindrical inclusions immersed in a homogeneous matrix. The thermal conductivity of the cylindrical inclusion is assumed to have a power-law profile of the radial distance r measured from its origin. For weakly nonlinear constitutive relations between the heat flow density q and the temperature field T, namely, q = -mu del T - chi vertical bar del T vertical bar(2) del T, in both the inclusion and the matrix regions, we have derived the temperature distributions using the perturbation expansion method. A nonlinear effective medium approximation of graded composites is proposed to estimate the effective linear and nonlinear thermal conductivities. by considering the temperature singularity on the inclusion surface due to the heat contact resistance. (c) 2006 Elsevier B.V. All rights reserved.

塔里木盆地塔北、塔中地区早古生代白云岩形成机理

In Tarim Basin, extensive carbonates of Lower Paleozoic occur, in which thick Cambrian and Lower Ordovician dolostones are widespread and show a potential perspective in hydrocarbon exploration. So they are viewed as an important target for exploration. Tarim Basin is a poly phase composite basin, which underwent multiphase tectonic modification and volcanic activities; these exerted significant influences on the basin-fills and basin fluid evolution, thereby the diagenetic history, particularly on the deep-buried Lower Paleozoic dolostones. Referring to the classification of dolomite texture proposed by Gregg & Sibley (1984) and Sibley & Gregg (1987). In view of crystal size, crystal shape, crystal surface and contact relation, eight genetic textures of dolomite crystals are identified, based on careful petrographic examinatoins. These textures include: 1) micritic dolomite; 2) relict mimetic dolomite; 3)finely crystalline, planar-e(s), floating dolomite; 4)finely crystalline, planar-e(s) dolomite; 5) finely-coarse crystalline, nonplanar-a dolomite; 6)coarse crystalline, nonplanar saddle dolomite; 7) finely-medium crystalline, planar-e(s) dolomite cement; 8) coarse crystalline, nonplanar saddle dolomite cement, in which the former six textures occurs as in matrix, the latter two in the cements. Detailed geochemistry analysis is carried out on the basis of genetic textures of dolomite and related minerals such as quartz and calcite. The result showed that the calcite has the highest average content in Sr, which can be sorted into two groups; micritic dolomite has the highest average content in Sr among all kinds of dolomites; the REE patterns of all kinds of dolomites is similar to those of marine limestone samples. Saddle dolomite cement has δ13C values from -2.44‰ to 1.27‰ PDB, and δ18O values from -13.01‰ to -5.12‰ PDB, which partially overlap with those of matrix dolomite (δ13C values from -2.83‰ to 2.01‰ PDB, δ18O values from -10.63‰ to -0.85‰ PDB). Saddle dolomite cement has 87Sr/86Sr ratios from 0.7086 to 0.7104, which totally overlap with those of matrix dolomite (0.7084 ~ 0.7116). Compared with saddle dolomite derived from other basins all over the world, the saddle dolomites of Tarim Basin have similar δ13C, δ18O and 87Sr/86Sr ratios values with those of matrix dolomite. This scenario reflects the unusual geological setting and special dolomitizing liquid of Tarim Basin. The values of δ18O, δ13C and 87Sr/86Sr ratios of calcite also can be sorted out two groups, which may been resulted from the one stage of extensive uplift of Tarim Basin from Mesozoic to Cenozoic. Fluid inclusion microthermometry data of the diagenetic mineral indicates that matrix dolomite has relatively low homogenization temperatures (Th) of 80～105oC and salinities of 12.3％ (wt% NaCl equivalent); saddle dolomite has highest Th values, which concentrate in 120～160oC and salinities of 13.5～23.7％ (wt% NaCl equivalent); quartz has relatively low Th of 135～155oC and salinities of 17.8～22.5％ (wt% NaCl equivalent); calcite has relatively low Th of 121～159.5oC and salinities of 1.4～17.5％ (wt% NaCl equivalent). These data suggest that the saddle dolomites could have formed in thermal brine fluids. Based on comprehensive petrographical study, detailed geochemistry and fluid inclusion microthermometry analysis on Lower Paleozoic dolomite of Tarim Basin, three types of dolomitisation mechanism are proposed: Penecontemporaneous dolomitisation (Sabkha dolomitisation & Reflux dolomitisation); Burial dolomitisation (shallow-intermediate burial dolomitisation & Deep burial dolomitisation ); Hydrothermal cannibalized dolomitisation. In view of host-specified occurrences of hydrothermal dolomite, the low abundance of saddle dolomite and high geochemical similarities between saddle dolomite and host dolomite, as well as highest Th and high salinities , the hydrothermal dolomite in Tarim Basin is thus unique, which could have been precipitated in modified fluid in the host dolomite through intraformational thermal fluid cannibalization of Mg ions from the host. This scenario is different from the cases that large scale dolomitizing fluid migration took place along the fluid pathways where abundant saddle dolomite precipitated. Detailed observations on 180 petrographic and 60 casting thin sections show original pores in Lower Paleozoic dolomite were almost died out by complicated diagenetic process after a long time geologic evolution. On the other hand, deep-buried dolomite reservoirs is formed by tectonic and hydrothermal reforming on initial dolomites. Therefore, the distribution of structure-controlled hydrothermal dolomite reservoirs is predicted in Tabei and Tazhong Area of Tarim Basin based on the geophysical data.

Contact Sensors for Dexterous Robotic Hands

This thesis examines a tactile sensor and a thermal sensor for use with the Utah-MIT dexterous four fingered hand. Sensory feedback is critical or full utilization of its advanced manipulatory capabilities. The hand itself provides tendon tensions and joint angles information. However, planned control algorithms require more information than these sources can provide. The tactile sensor utilizes capacitive transduction with a novel design based entirely on silicone elastomers. It provides an 8 x 8 array of force cells with 1.9 mm center-to-center spacing. A pressure resolution of 8 significant bits is available over a 0 to 200 grams per square mm range. The thermal sensor measures a material's heat conductivity by radiating heat into an object and measuring the resulting temperature variations. This sensor has a 4 x 4 array of temperature cells with 3.5 mm center-to-center spacing. Experiments show that the thermal sensor can discriminate among material by detecting differences in their thermal conduction properties. Both sensors meet the stringent mounting requirements posed by the Utah-MIT hand. Combining them together to form a sensor with both tactile and thermal capabilities will ultimately be possible. The computational requirements for controlling a sensor equipped dexterous hand are severe. Conventional single processor computers do not provide adequate performance. To overcome these difficulties, a computational architecture based on interconnecting high performance microcomputers and a set of software primitives tailored for sensor driven control has been proposed. The system has been implemented and tested on the Utah-MIT hand. The hand, equipped with tactile and thermal sensors and controlled by its computational architecture, is one of the most advanced robotic manipulatory devices available worldwide. Other ongoing projects will exploit these tools and allow the hand to perform tasks that exceed the capabilities of current generation robots.

‘It was almost like the opposite of what I needed’: a qualitative exploration of client experiences of unhelpful therapy

Background: The issue of unhelpful and harmful therapy outcome has received an increasing amount of attention within the research literature in recent years. However, little research exists on the client's perspective of what constitutes unhelpful therapy. Aim: The aim of this study was to explore clients’ experiences of unhelpful therapy. Method: Semi-structured interviews were carried out with ten therapists who, as clients, experienced unhelpful therapy. Interview transcripts were analysed using interpretative phenomenological analysis. Findings: Participants recounted therapy episodes characterised by an absence of negotiation, collaboration and care; pivotal moments when they knew that they would not return; and ongoing negative effects. Conclusions: The findings of this study have implications for training and strategies for supporting clients who have been harmed by therapy.

Securing Bulk Content Almost for Free

Content providers often consider the costs of security to be greater than the losses they might incur without it; many view "casual piracy" as their main concern. Our goal is to provide a low cost defense against such attacks while maintaining rigorous security guarantees. Our defense is integrated with and leverages fast forward error correcting codes, such as Tornado codes, which are widely used to facilitate reliable delivery of rich content. We tune one such family of codes - while preserving their original desirable properties - to guarantee that none of the original content can b e recovered whenever a key subset of encoded packets is missing. Ultimately we encrypt only these key codewords (only 4% of all transmissions), making the security overhead negligible.