A compact lightweight multipurpose ground-penetrating radar for glaciological applications

We describe a compact lightweight impulse radar for radio-echo sounding of subsurface structures designed specifically for glaciological applications. The radar operates at frequencies between 10 and 75 MHz. Its main advantages are that it has a high signal-to-noise ratio and a corresponding wide dynamic range of 132 dB due mainly to its ability to perform real-time stacking (up to 4096 traces) as well as to the high transmitted power (peak voltage 2800 V). The maximum recording time window, 40 ?s at 100 MHz sampling frequency, results in possible radar returns from as deep as 3300 m. It is a versatile radar, suitable for different geophysical measurements (common-offset profiling, common midpoint, transillumination, etc.) and for different profiling set-ups, such as a snowmobile and sledge convoy or carried in a backpack and operated by a single person. Its low power consumption (6.6 W for the transmitter and 7.5 W for the receiver) allows the system to operate under battery power for mayor que7 hours with a total weight of menor que9 kg for all equipment, antennas and batteries.

Evapotranspiration of grapevine trained to a gable trellis system under netting and black plastic mulching

The evapotranspiration (ET c) of a table grape vineyard (Vitis vinifera, cv. Red Globe) trained to a gable trellis under netting and black plastic mulching was determined under semiarid conditions in the central Ebro River Valley during 2007 and 2008. The netting was made of high-density polyethylene (pores of 12 mm2) and was placed just above the ground canopy about 2.2 m above soil surface. Black plastic mulching was used to minimize soil evaporation. The surface renewal method was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Later, latent heat flux (LE) values were obtained by solving the energy balance equation. For the May–October period, seasonal ET c was about 843 mm in 2007 and 787 mm in 2008. The experimental weekly crop coefficients (K cexp) fluctuated between 0.64 and 1.2. These values represent crop coefficients adjusted to take into account the reduction in ET c caused by the netting and the black plastic mulching. Average K cexp values during mid- and end-season stages were 0.79 and 0.98, respectively. End-season K cexp was higher due to combination of factors related to the precipitation and low ET o conditions that are typical in this region during fall. Estimated crop coefficients using the Allen et al. (1998) approach adjusting for the effects of the netting and black plastic mulching (K cFAO) showed a good agreement with the experimental K cexp values.

On-board and Ground Visual Pose Estimation Techniques for UAV Control

In this paper, two techniques to control UAVs (Unmanned Aerial Vehicles), based on visual information are presented. The first one is based on the detection and tracking of planar structures from an on-board camera, while the second one is based on the detection and 3D reconstruction of the position of the UAV based on an external camera system. Both strategies are tested with a VTOL (Vertical take-off and landing) UAV, and results show good behavior of the visual systems (precision in the estimation and frame rate) when estimating the helicopter¿s position and using the extracted information to control the UAV.

Real-time image processing for crop/weed discrimination in maize fields

This paper presents a computer vision system that successfully discriminates between weed patches and crop rows under uncontrolled lighting in real-time. The system consists of two independent subsystems, a fast image processing delivering results in real-time (Fast Image Processing, FIP), and a slower and more accurate processing (Robust Crop Row Detection, RCRD) that is used to correct the first subsystem's mistakes. This combination produces a system that achieves very good results under a wide variety of conditions. Tested on several maize videos taken of different fields and during different years, the system successfully detects an average of 95% of weeds and 80% of crops under different illumination, soil humidity and weed/crop growth conditions. Moreover, the system has been shown to produce acceptable results even under very difficult conditions, such as in the presence of dramatic sowing errors or abrupt camera movements. The computer vision system has been developed for integration into a treatment system because the ideal setup for any weed sprayer system would include a tool that could provide information on the weeds and crops present at each point in real-time, while the tractor mounting the spraying bar is moving

Multi-microphone recordings (EigenMike32) inside a WFS system (Iosono) through Ambisonics techniques using Matlab

El audio multicanal ha avanzado a pasos agigantados en los últimos años, y no solo en las técnicas de reproducción, sino que en las de capitación también. Por eso en este proyecto se encuentran ambas cosas: un array microfónico, EigenMike32 de MH Acoustics, y un sistema de reproducción con tecnología Wave Field Synthesis, instalado Iosono en la Jade Höchscule Oldenburg. Para enlazar estos dos puntos de la cadena de audio se proponen dos tipos distintos de codificación: la reproducción de la toma horizontal del EigenMike32; y el 3er orden de Ambisonics (High Order Ambisonics, HOA), una técnica de codificación basada en Armónicos Esféricos mediante la cual se simula el campo acústico en vez de simular las distintas fuentes. Ambas se desarrollaron en el entorno Matlab y apoyadas por la colección de scripts de Isophonics llamada Spatial Audio Matlab Toolbox. Para probar éstas se llevaron a cabo una serie de test en los que se las comparó con las grabaciones realizadas a la vez con un Dummy Head, a la que se supone el método más aproximado a nuestro modo de escucha. Estas pruebas incluían otras grabaciones hechas con un Doble MS de Schoeps que se explican en el proyecto “Sally”. La forma de realizar éstas fue, una batería de 4 audios repetida 4 veces para cada una de las situaciones garbadas (una conversación, una clase, una calle y un comedor universitario). Los resultados fueron inesperados, ya que la codificación del tercer orden de HOA quedo por debajo de la valoración Buena, posiblemente debido a la introducción de material hecho para un array tridimensional dentro de uno de 2 dimensiones. Por el otro lado, la codificación que consistía en extraer los micrófonos del plano horizontal se mantuvo en el nivel de Buena en todas las situaciones. Se concluye que HOA debe seguir siendo probado con mayores conocimientos sobre Armónicos Esféricos; mientras que el otro codificador, mucho más sencillo, puede ser usado para situaciones sin mucha complejidad en cuanto a espacialidad. In the last years the multichannel audio has increased in leaps and bounds and not only in the playback techniques, but also in the recording ones. That is the reason of both things being in this project: a microphone array, EigenMike32 from MH Acoustics; and a playback system with Wave Field Synthesis technology, installed by Iosono in Jade Höchscule Oldenburg. To link these two points of the audio chain, 2 different kinds of codification are proposed: the reproduction of the EigenMike32´s horizontal take, and the Ambisonics´ third order (High Order Ambisonics, HOA), a codification technique based in Spherical Harmonics through which the acoustic field is simulated instead of the different sound sources. Both have been developed inside Matlab´s environment and supported by the Isophonics´ scripts collection called Spatial Audio Matlab Toolbox. To test these, a serial of tests were made in which they were compared with recordings made at the time by a Dummy Head, which is supposed to be the closest method to our hearing way. These tests included other recording and codifications made by a Double MS (DMS) from Schoeps which are explained in the project named “3D audio rendering through Ambisonics techniques: from multi-microphone recordings (DMS Schoeps) to a WFS system, through Matlab”. The way to perform the tests was, a collection made of 4 audios repeated 4 times for each recorded situation (a chat, a class, a street and college canteen or Mensa). The results were unexpected, because the HOA´s third order stood under the Well valuation, possibly caused by introducing material made for a tridimensional array inside one made only by 2 dimensions. On the other hand, the codification that consisted of extracting the horizontal plane microphones kept the Well valuation in all the situations. It is concluded that HOA should keep being tested with larger knowledge about Spherical Harmonics; while the other coder, quite simpler, can be used for situations without a lot of complexity with regards to spatiality.

Automatic-dependent surveillance-broadcast experimental deployment using system wide information management

This paper describes an automatic-dependent surveillance-broadcast (ADS-B) implementation for air-to-air and ground-based experimental surveillance within a prototype of a fully automated air traffic management (ATM) system, under a trajectory-based-operations paradigm. The system is built using an air-inclusive implementation of system wide information management (SWIM). This work describes the relations between airborne and ground surveillance (SURGND), the prototype surveillance systems, and their algorithms. System's performance is analyzed with simulated and real data. Results show that the proposed ADS-B implementation can fulfill the most demanding surveillance accuracy requirements.

Terapias auditivas para acúfenos (tinnitus)

Un acúfeno (tinnitus) es la percepción de un sonido en ausencia de estimulación acústica externa, es decir, la experiencia consciente de un sonido que se origina en la propia cabeza del paciente. En colaboración con el departamento de acústica (CAEND) del Consejo Superior de Investigaciones Científicas (CSIC), se pretende revertir (de forma paliativa) las molestias, con ayuda de terapias sonoras que estimulan el sistema auditivo. Primero, se analizan los tratamientos existentes que se utilizan para atender a los pacientes diagnosticados. Por último, se diseñan dos aplicaciones informáticas referentes a las terapias: Auditory Discrimination Training (ADT) y Enriched Acoustic Environment (EAE). Abstract Tinnitus is the perception of sound in the absence of external acoustic stimulation, in addition, the conscious experience a sound originating from the patient’s own head. In collaboration with the department of acoustic (CAEND) of the Consejo Superior de Investigaciones Científicas (CSIC), is to reverse (for palliation) discomfort, using sound therapies that stimulate the auditory system. First, we analyze the existing treatments are used to treat patients diagnosed. Finally, two applications are designed regarding therapies: Auditory Discrimination Training (ADT) and Enriched Acoustic Environment (EAE).

Observation and Detection of Underground Cellars in the Duero Basin By GNSS, Lidar and Ground Penetrating Radar Techniques

The underground cellars that appear in different parts of Spain are part of an agricultural landscape dispersed, sometimes damaged, others at risk of disappearing. This paper studies the measurement and display of a group of wineries located in Atauta (Soria), in the Duero River corridor. It is a unique architectural complex, facing rising, built on a smooth hillock as shown in Fig. 1. These constructions are excavated in the ground. The access to the cave or underground cellar has a shape of a narrow tube or down gallery. Immediately after, this space gets wider. There, wine is produced and stored [1]. Observation and detection of the underground cellar, both on the outside and underground, it is essential to make an inventory of the rural patrimony [2]. The geodetection is a noninvasive technique, adequate to accurately locate buried structures in the ground. Works undertaken include topographic work with the LIDAR techniques and integration with data obtained by GNSS and GPR.

Acoustic characterisation of cinema screens

As a consequence of cinema screens being placed in front of screen-speakers, a reduction in sound quality has been noticed. Cinema screens not only let the sound go through them, but also absorb a small amount of it and reflect the sound which impacts on the screen to the back, coming forward again in case it impacts on the loudspeaker. This backwards reflection in addition to the signal coming from the loudspeaker can lead to constructive or destructive interference at certain frequencies which usually results in comb filtering. In this project, this effect has been studied through researching amongst various data sheet provided by different manufacturers, acoustical measurements completed in the large anechoic chamber of the ISVR and some theoretical models developed with MatLab software. If results obtained with MatLab are accurate enough in comparison to the real measurements taken in the anechoic chamber this would lead to a good way to predict which would be the attenuation added to the system at each frequency, given that not all manufacturers provide an attenuation curve, but only an average attenuation. This average attenuation might be useless as sound waves have different wavelengths and its propagation through partitions varies. In fact, sound is composed by high and low frequencies, where high frequencies are characterised by a small wavelength which is usually easier to attenuate than low frequencies that characterised by bigger wavelengths. Furthermore, this information would be of great value to both screen manufacturers, who could offer a much more precise data in their data sheets; and customers, who would have a great amount of information to their disposal before purchasing and installing anything in their cinemas, being able to know by themselves which screen or loudspeaker should be best to meet their expectative. RESUMEN. La aparición de la digitalización de las bandas sonoras para las películas hace posible la mejora en la calidad de sonido de los cines. Sin embargo, un aspecto a tener en cuenta en esta calidad del sonido es la transmisión de éste a través de la pantalla, ya que normalmente tras ella se encuentran situados los altavoces. Las propiedades acústicas varían dependiendo del tipo de pantalla que se utilice, además de haber poca información a la que acceder para poder valorar su comportamiento. A lo largo de este proyecto, se analizan tres muestras de pantallas distintas donadas por distintos fabricantes para poder llegar a la conclusión de dependiendo del tipo de pantalla cuál es la distancia óptima a la que localizar la pantalla respecto al altavoz y con qué inclinación. Dicho análisis se realizó en la cámara anecoica del ISVR (University of Southampton) mediante la construcción de un marco de madera de 2x2 m en el que tensar las pantallas de cine, y un altavoz cuyo comportamiento sea el más similar al de los altavoces de pantalla reales. Los datos se captaron mediante cuatro micrófonos colocados en posiciones distintas y conectados al software Pulse de Brüel & Kjær, a través del cual se obtuvieron las respuestas en frecuencia del altavoz sin pantalla y con ella a diferentes distancias del altavoz. Posteriormente, los datos se analizaron con MatLab donde se calculó la atenuación, el factor de transmisión de la presión (PTF) y el análisis cepstrum. Finalmente, se realizó un modelo teórico del comportamiento de las pantallas perforadas basado en las placas perforadas utilizadas para atenuar el sonido entre distintas habitaciones. Como conclusión se llegó a que las pantallas curvadas son acústicamente más transparentes que las pantallas perforadas que a partir de 6 kHz son más acústicamente opacas. En las pantallas perforadas la atenuación depende del número de perforaciones por unidad de área y el diámetro de éstas. Dicha atenuación se reducirá si se reduce el diámetro de las perforaciones de la pantalla, o si se incrementa la cantidad de perforaciones. Acerca del efecto filtro peine, para obtener la mínima amplitud de éste la pantalla se deberá situar a una distancia entre 15 y 30 cm del altavoz, encontrando a la distancia de 30 cm que la última reflexión analizada a través de Cepstrum llega 5 ms más tarde que la señal directa, por lo cual no debería dañar el sonido ni la claridad del habla.

Influence of loudspeaker directivity and measurement geometry on direct acoustic levels over façades for acoustic insulation tests with the International Standard ISO 140-5

The International Standard ISO 140-5 on field measurements of airborne sound insulation of façades establishes that the directivity of the measurement loudspeaker should be such that the variation in the local direct sound pressure level (ΔSPL) on the sample is ΔSPL < 5 dB (or ΔSPL < 10 dB for large façades). This condition is usually not very easy to accomplish nor is it easy to verify whether the loudspeaker produces such a uniform level. Direct sound pressure levels on the ISO standard façade essentially depend on the distance and directivity of the loudspeaker used. This paper presents a comprehensive analysis of the test geometry for measuring sound insulation and explains how the loudspeaker directivity, combined with distance, affects the acoustic level distribution on the façade. The first sections of the paper are focused on analysing the measurement geometry and its influence on the direct acoustic level variations on the façade. The most favourable and least favourable positions to minimise these direct acoustic level differences are found, and the angles covered by the façade in the reference system of the loudspeaker are also determined. Then, the maximum dimensions of the façade that meet the conditions of the ISO 140-5 standard are obtained for the ideal omnidirectional sound source and the piston radiating in an infinite baffle, which is chosen as the typical radiation pattern for loudspeakers. Finally, a complete study of the behaviour of different loudspeaker radiation models (such as those usually utilised in the ISO 140-5 measurements) is performed, comparing their radiation maps on the façade for searching their maximum dimensions and the most appropriate radiation configurations.

Criteria for mathematical model selection for satellite vibro-acoustic analysis depending on frequency range

Satellites and space equipment are exposed to diffuse acoustic fields during the launch process. The use of adequate techniques to model the response to the acoustic loads is a fundamental task during the design and verification phases. Considering the modal density of each element is necessary to identify the correct methodology. In this report selection criteria are presented in order to choose the correct modelling technique depending on the frequency ranges. A model satellite’s response to acoustic loads is presented, determining the modal densities of each component in different frequency ranges. The paper proposes to select the mathematical method in each modal density range and the differences in the response estimation due to the different used techniques. In addition, the methodologies to analyse the intermediate range of the system are discussed. The results are compared with experimental testing data obtained in an experimental modal test.

Expectations from EMET and OESEE ground listening of possible EM events generated by the TSS 1R

On 22nd February '96, the space mission STS 75 started ,from the NASA facilities at Cape Canaveral. Such a mission consists in the launch of the shuttle Columbia in order to carry out two experiments in the space: the TSS 1R (Tethered Satellite Sistem 1 Refliight) and the USMP (United States Microgravity Payload). The TSS 1R is a replica of a similar mission TSS 1 '92. The TSS space programme is a bilateral scientific cooperation between the USA space agency NASA (National Aeronautics and Space Agency) and the ASI (Italian Space Agency. The TSS 1R system consists on the shuttle Columbia which deploys, up-ward, by means a conducting tether 20 km long, a spherical satellite (1.5 mt diameter) containing scientific instrumentation. This system, orbiting at about 300 km from the Earth's surface, represents, presently, the largest experimental space structure, Due to its dimensions, flexibility and conducting properties of the tether, the system interacts, in a quite complex manner, wih the earth magnetic field and the ionospheric plasma, in a way that the total system behaves as an electromagnetic radiating antenna as well as an electric power generator. Twelve scientific experiments have been assessed by US and Italian scientists in order to study the electro dynamic behaviour of the structure orbiting in the ionos phere. Two experiments have been prepared in the attempt to receive on the Earth's surface possible electromagnetic events radiated by the TSS 1R. The project EMET (Electro Magnetic Emissions from Tether),USA and the project OESEE (Observations on the Earth Surface of Electromagnetic Emissions) Italy, consist in a coordinated programme of passive detection of such possible EM emissions. This detection will supply the verification of some thoretical hypotheses on the electrodynamic interactions between the orbiting system, the Earth's magnetic field and the ionospheric plasma with two principal aims as the technological assesment of the system concept as well as a deeper knowledge of the ionosphere properties for future space applications. A theoretical model that keeps the peculiarities of tether emissionsis being developed for signal prediction at constant tether current. As a step previous to the calculation of the expected ground signal , the Alfven-wave signature left by the tether far back in the ionosphere has been determined. The scientific expectations from the combined effort to measure the entity of those perturbations will be outlined taking in to account the used ground track sensor systems.

Low-resource language recognition using a fusion of phoneme posteriorgram counts, acoustic and glottal-based i-vectors

This paper presents a description of our system for the Albayzin 2012 LRE competition. One of the main characteristics of this evaluation was the reduced number of available files for training the system, especially for the empty condition where no training data set was provided but only a development set. In addition, the whole database was created from online videos and around one third of the training data was labeled as noisy files. Our primary system was the fusion of three different i-vector based systems: one acoustic system based on MFCCs, a phonotactic system using trigrams of phone-posteriorgram counts, and another acoustic system based on RPLPs that improved robustness against noise. A contrastive system that included new features based on the glottal source was also presented. Official and postevaluation results for all the conditions using the proposed metrics for the evaluation and the Cavg metric are presented in the paper.

Discrimination of AE Signals From Friction and Concrete Cracking in a Reinforced Concrete Frame Subjected to Seismic Trainings

This paper shows the preliminary results of the development and application of a procedure to filter the Acoustic Emission (AE) signals to distinguish between AE signals coming from friction and AE signals coming from concrete cracking. These signals were recorded during the trainings of an experiment carried out on a reinforced concrete frame subjected to dynamic loadings with the shaking table of the University of Granada (Spain). Discrimination between friction and cracking AE signals is the base to develop a successful procedure and damage index based on AE testing for health monitoring of RC structures subjected to earthquakes.