Avaliação de diferentes tipos de atmosferas modificadas na vida útil de carambolas minimamente processadas

Este trabalho teve por objetivo a avaliação da vida útil potencial de carambolas cv. Golden Star, minimamente processadas, armazenadas em diferentes tipos de embalagens plásticas, para a concepção da atmosfera modificada. Os frutos colhidos fisiologicamente maturos apresentaram coloração verde-amarelada, sólidos solúveis (SS) médios de 6,8 ºBrix e massa média de 185 g. Antes da aplicação dos tratamentos, os frutos foram selecionados, higienizados em solução de hipoclorito de sódio (NaOCl) a 100 mg. L-1, resfriados por 12 horas a 15 ± 0,5 °C, seccionados transversalmente, sendo então novamente higienizados em solução de NaOCl a 10 mg.L-1, por 3 minutos. em seguida, os pedaços em forma de estrelas foram acondicionados em bandejas rígidas de poliestireno, com capacidade para 250 g, e revestidas com os seguintes materiais: T1: filme plástico perfurado de polietileno de baixa densidade (PEBD), de 0,006 mm; T2: filme plástico poliolefínico com antiembassamento da Dupont® (AGF), de 0,015 mm; T3: filme plástico poliolefínico da Dupont® (HF), de 0,015 mm; T4: filme plástico de PEBD, de 60 µm; T5: filme plástico de PEBD, de 80 µm; T6: filme plástico de polipropileno (PP), de 22 µm, e T7: bandeja rígida de polietileno tereftalato (PET), com capacidade para 500 mL, com tampa do mesmo material. As embalagens foram então armazenadas em câmara frigorífica a 12 ± 0,5 °C e 90 ± 3% de U.R, por 18 dias. Observou-se que não houve diferença significativa quanto aos sólidos solúveis (SS) e acidez titulável (AT). O maior número de microrganismos e valor de pH foram observados nos frutos embalados nos filmes plásticos de PEBD de 0,006 mm, AGF e HF de 0,015 mm da Dupont®. Entretanto, os frutos acondicionados nas embalagens PET apresentaram o maior teor de ácido ascórbico. da mesma forma, somente nas embalagens PET é que se conseguiu modificação atmosférica eficiente do ponto de vista da manutenção dos atributos de qualidade durante o AR. Assim, esse tratamento proporcionou adequado controle microbiológico e manutenção das características de qualidade por 18 dias para as carambolas minimamente processadas.

Caracterização físico-química, bioquímica e funcional da jabuticaba armazenada sob diferentes temperaturas

O presente trabalho teve como objetivo avaliar a qualidade pós-colheita de jabuticabas submetidas a diferentes temperaturas de armazenamento refrigerado (AR). Após a colheita, os frutos fisiologicamente maduros foram acondicionados em bandejas de poliestireno expandido (EPS), revestidas por filme plástico de polietileno de baixa densidade (PEBD) e armazenados sob refrigeração a 0; 3; 6; 9 e 12 ± 1ºC e U.R. 87 ± 2%, sendo avaliados a cada 5 dias. Os frutos foram avaliados quanto à perda de massa, atividade respiratória, pH, acidez titulável, sólidos solúveis, ácido ascórbico, textura, pectina total e solúvel, atividade da enzima polifenoloxidase (PFO), compostos fenólicos e atividade antioxidante. Para frutos refrigerados a 9 e 12ºC, o pico respiratório atrasou em relação aos demais tratamentos, além de apresentarem as menores taxas respiratórias. O teor de sólidos solúveis aumentou com o tempo de armazenamento para todas as temperaturas, contudo, em 9 e 12ºC, esse aumento foi em menor proporção. A firmeza e o teor de ácido ascórbico também foram superiores nos frutos armazenados a 9 e 12ºC, enquanto os contéudos de pectina solúvel foram menores. Observou-se a diminuição da atividade da enzima PFO ao longo dos 30 dias do AR, independentemente da temperatura utilizada; entretanto, os menores valores foram encontrados nos frutos mantidos a 9 e 12ºC. Os frutos armazenados a 12ºC apresentaram os maiores conteúdos de compostos fenólicos totais e a maior atividade antioxidante ao final do experimento. Nesse sentido, a temperatura de 12ºC foi a mais efetiva na manutenção da qualidade pós-colheita das jabuticabas.

Colored polyethylene soil covers and grafting effects on cucumber flowering and yield

O pepino (Cucumis sativus L.) é, dentre os produtos hortícolas, um dos mais visados para o cultivo em estufas no Brasil devido ao ciclo vegetativo curto e ao elevado valor econômico no período da entressafra. Estudou-se, em condições de ambiente protegido, a influência de diferentes cores de cobertura plástica de solo no florescimento e na produção de pepino híbrido 'Yoshinari' enxertado ou não sobre abóbora híbrida 'Ikky'. Os tratamentos de cobertura foram: preto, preto pintado de branco, verde, e sem cobertura. Os tratamentos cobertos com plástico e sem enxertia apresentaram florescimento com distribuição mais uniforme na planta. O número de flores foi superior no tratamento preto/branco enxertado. Para as plantas não enxertadas, todas as coberturas favoreceram o florescimento. A enxertia favoreceu o florescimento somente para os tratamentos com plástico preto ou verde. A fixação dos frutos aumentou pelo uso de cobertura plástica, mas a enxertia não teve influência. A distribuição uniforme do florescimento manteve-se na frutificação apenas para os tratamentos com plantas enxertadas e cobertura do solo com plástico preto ou verde. Tanto o uso de cobertura plástica quanto a enxertia favoreceram a colheita precoce. Os frutos de melhor qualidade e as maiores produções, em número de frutos, foram obtidos nos tratamentos preto e preto/branco, não enxertados. A enxertia 'Yoshinari'/'Ikky' provocou o aparecimento de frutos mais grossos e menores, fora do padrão de comercialização.

Synthesis of poly(styrene-co-methyl methacrylate)-based ionomers and their Langmuir and Langmuir-Blodgett (LB) film formation

Poly(styrene-co-methyl methacrylate) (PS-PMMA) ionomers with several degrees of sulfonation were synthesized and characterized by infrared, UV-vis, and NMR spectroscopies, elemental analysis, and differential scanning calorimetry (DSC). Stable Langmuir films could be produced with PS-PMMA with 3 and 6 mol % of sulfonation, while PS-PMMA 8% exhibited material loss to the water subphase, probably due to its higher solubility. Surface pressure and surface potential isotherms with PS-PMMA 3% spread onto salt-containing subphases pointed to a film behavior characteristic of the polyelectrolyte effect, where charge repulsion governs the film properties. The Langmuir-Blodgett films of this ionomer were successfully transferred onto various substrates, as confirmed by UV-vis and FTIR spectroscopies. Using cycling voltammetry, we show that LB films from PS-PMMA 3% can be applied in selective sensing of dopamine, even in the presence of interferents such as ascorbic acid.

A layer-by-layer film of chitosan in a taste sensor application

Chitosan is alternated with sulfonated polystyrene (PSS) to build layer-by-layer (LBL) films that are used as sensing units in an electronic tongue. Using impedance spectroscopy as the principle method of detection, an array using chitosan/PSS LBL film and a bare gold electrode as the sensing units was capable of distinguishing the basic tastes - salty, sweet, bitter, and sour - to a concentration below the human threshold. The suitability of chitosan as a sensing material was confirmed by using this sensor to distinguish red wines according to their vintage, vineyard, and brands.

An electrochemical sensor for (L)-dopa based on oxovanadium-salen thin film electrode applied flow injection system

An oxovanadium-salen complex (NAP-ethylene-bis(salicylidenciminato) oxovanadium) thin film deposited on a graphite-polyurethane electrode was investigated with regard to its potential use for detection of L-dopa in flow injection system. The oxovanadium(IV)/oxovanadium(V) redox couple of the modified electrode was found to mediate the L-dopa oxidation before its use in the FIA system. Experimental parameters, such as pH of the carrier solution, flow rate, sample volume injection and probable interferents were investigated. Under the optimized FIA conditions, the amperometric signal was linearly dependent on the L-dopa concentration over the range 1.0 x 10(-1) to 1.0 x 10(-4) mol L-1 (I-anodic, mu A) = 0.01 + 0.25 [L-dopa mu mol L-1]) with a detection limit (S/N = 3) of 8.0 x 10(-7) mol L-1 and a sampling frequency of 90 h(-1) was achieved. For a concentration of 1.0 x 10(-5) mol L-1 L-dopa, the R.S.D. of nine consecutive measurements was 3.7%. (c) 2006 Elsevier B.V. All rights reserved.

Electrochemical sensor for sulfite determination based on a nanostructured copper-salen film modified electrode

The electrochemical preparation described herein involved the electrocatalytic oxidation of sulfite on a platinum electrode modified with nanostructured copper salen (salen=N,N'-ethylenebis(salicylideneiminato)) polymer films. The complex was prepared and electropolymerized at a platinum electrode in a 0.1 mol L-1 solution of tetrabutylammonium perchlorate in acetonitrile by cyclic voltammetry between 0 and 1.4V vs. SCE. After cycling the modified electrode in a 0.50 mol L-1 KCI solution, the estimated surface concentration was found to be equal to 2.2 x 10(-9) Mol cm(-2). This is a typical behavior of an electrode surface immobilized with a redox couple that can usually be considered as a reversible single-electron reduction/oxidation of the copper(II)/copper(III) couple. The potential peaks of the modified electrode in the electrolyte solution (aqueous) containing the different anions increase with the decrease of the ionic radius, demonstrating that the counter-ions influence the voltammetric behavior of the sensor. The potential peak was found to be linearly dependent upon the ratio [ionic charge]/[ionic radius]. The oxidation of the sulfite anion was performed at the platinum electrode at +0.9V vs. SCE. However, a significant decrease in the overpotential (+0.45V) was obtained while using the sensor, which minimized the effect of oxidizable interferences. A plot of the anodic current vs. the sulfite concentration for chronoamperometry (potential fixed = +0.45V) at the sensor was linear in the 4.0 x 10(-6) to 6.9 x 10(-5) mol L-1 concentration range and the concentration limit was 1.2 x 10(-6) mol L-1. The reaction order with respect to sulfite was determined by the slope of the logarithm of the current vs. the logarithm of the sulfite concentration. (C) 2009 Elsevier Ltd. All rights reserved.

Development of an electrochemical sensor for determination of dissolved oxygen by nickel-salen polymeric film modified electrode

An amperometric oxygen sensor based on a polymeric nickel-salen (salen = N,N'-ethylene bis(salicylideneiminato)) film coated platinum electrode was developed. The sensor was constructed by electropolymerization of nickel-salen complex at platinum electrode in acetonitrile/tetrabutylammonium perchlorate by cyclic voltammetry. The voltammetric behavior of the sensor was investigated in 0.5 mol L-1 KCl solution in the absence and presence of molecular oxygen. Thus, with the addition of oxygen to the solution, the increase of cathodic peak current (at -0.25 V vs. saturated calomel electrode (SCE)) of the modified electrode was observed. This result shows that the nickel-salen film on electrode surface promotes the reduction of oxygen. The reaction can be brought about electrochemically, where the nickel(II) complex is first reduced to a nickel(I) complex at the electrode surface. The nickel(I) complex then undergoes a catalytic oxidation by the molecular oxygen in solution back to the nickel(II) complex, which can then be electrochemically re-reduced to produce an enhancement of the cathodic current. The Tafel plot analyses have been used to elucidate the kinetics and mechanism of the oxygen reduction. A plot of the cathodic current vs. the dissolved oxygen concentration for chronoamperometry (fixed potential = -0.25 V vs. SCE) at the sensor was linear in the 3.95-9.20 mg L-1 concentration range and the concentration limit was 0.17 mg L-1 O-2. The proposed electrode is useful for the quality control and routine analysis of dissolved oxygen in commercial samples and environmental water. The results obtained for the levels of dissolved oxygen are in agreement with the results obtained with a commercial O-2 sensor. (C) 2012 Elsevier B.V. All rights reserved.

Electrochemical investigation of the dimeric oxo-bridged ruthenium complex in aqueous solution and its incorporation within a cation-exchange polymeric film on the electrode surface for electrocatalytic activity of hydrogen peroxide oxidation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Film based on Y2O3: Eu3+ (5 mol% of Eu3+) for flat panel display

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

An electrochemical sensor for dipyrone determination based on nickel-salen film modified electrode

An amperometric dipyrone sensor based on a polymeric nickel-salen (salen = N,N'-ethylenebis(salicydeneiminato)) film coated platinum electrode was developed. The sensor was constructed by electropolymerization of nickel-salen complex at a platinum electrode in acetonitrile/tetrabuthylamonium perchlorate by cyclic voltammetry. After cycling the modified electrode in a 0.50 mol L-1 KCl solution, the estimated surface concentration was found to be equal to 1.29 x 10(-9) mol cm(-2). This is a typical behavior of an electrode surface immobilized with a redox couple that can usually be considered as a reversible single-electron reduction/oxidation of the nickel(II)/nickel(III) couple. A plot of the anodic current versus the dipyrone concentration for chronoamperometry (potential fixed = +0.50 V) at the sensor was linear in the 4.7 x 10(-6) to 1.1 x 10(-4) mol L-1 concentration range and the concentration limit was 1.2 x 10(-6) mol L-1. The proposed electrode is useful for the quality control and routine analysis of dipyrone in pharmaceutical formulations.

Development of Nanostructured Electrochemical Sensor Based on Polymer Film Nickel-Salen for Determination of Dissolved Oxygen

An amperometric oxygen sensor based on a polymeric nickel-salen (salen = N,N '-ethylenebis(salicydeneiminato)) film coated platinum electrode was developed. The sensor was constructed by electropolymerization of nickel-salen complex at a platinum electrode in acetonitrile/tetrabuthylamonium perchlorate by cyclic voltammetry. The voltammetric behavior of the modified electrode was investigated in 0.5 mol L-1 KCl solution in the absence and presende of molecular oxygen. A significant increased of cathodic peak current (at -0.20 vs. SCE) of the modified electrode with addition of oxygen to the solution was observed. This result shows that the nickel-salen film on the surface of the electrode promotes the reduction of oxygen. The reaction can be brought about electrochemically where in the nickel(II) complex is first reduced to a nickel(I) complex at the electrode surface. The nickel(I) complex then undergoes a catalytic oxidation by the oxygen molecular in solution back to the nickel(II) complex, which can then be electrochemically re-reduced to produce an enhancement of the cathodic current. The plot of the cathodic current versus the dissolved oxygen concentration for chronoamperometry (potential fixed = -0.20 V) at the sensor was linear in the concentration range of 3.95 to 9.20 mg L-1 with concentration limit of 0.17 mg L-1 O-2. The modified electrode proposed is useful for the quality control and routine analysis of dissolved oxygen in commercial water and environmental water samples. The results obtained for the levels of dissolved oxygen are in agreement with the results obtained with an O-2 commercial sensor. (C) 2011 Published by Elsevier Ltd.

Numerical simulation of the liquid phase in SnO2 thin film deposition by sol-gel-dip-coating

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Growth of Al2O3 thin film by oxidation of resistively evaporated Al on top of SnO2, and electrical properties of the heterojunction SnO2/Al2O3

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Nanohardness of a Ti thin film and its interface deposited by an electron beam on a 304 SS substrate

The results of nanohardness measurements at a film surface and film-substrate interface are presented and discussed. An electron beam device was used to deposit a Ti film on a 304 stainless steel (304 SS) substrate. The diluted interface was obtained by thermal activated atomic diffusion. The. Ti film and Ti film-304 SS interface were analyzed by energy dispersive spectrometry and were observed using atomic force microscopy. The nanohardness of the Ti film-304 SS system was measured by a nanoindentation technique. The results showed the Ti film-304 SS interface had a higher hardness value than the Ti film and 304 SS substrate. The Ti film surface had a lower hardness due to the presence of a TiO2 thin layer.