A moored underwater energy conservation system for profiling measurement

There is a need to obtain the hydrologic data including ocean current, wave, temperature and so on in the South China Sea. A new profiling instrument which does not suffer from the damage due to nature forces or incidents caused by passing ships, is under development to acquire data from this area. This device is based on a taut single point mid-water mooring system. It incorporates a small, instrumented vertically profiling float attached via an electromechanical cable to a winch integral with the main subsurface flotation. On a pre-set schedule, the instrument float with sensors is winched up to the surface if there is no strip passing by, which is defined by an on-board miniature sonar. And it can be immediately winched down to a certain depth if the sonar sensor finds something is coming. Since, because Of logistics, the area can only be visited once for a long time and a minimum of 10 times per day profiles are desired, energy demands are severe. To respond to these concerns, the system has been designed to conserve a substantial portion of the potential energy lost during the ascent phase of each profile and subsequently use this energy to pull the instrument down. Compared with the previous single-point layered measuring mode, it is advanced and economical. At last the paper introduces the test in the South China Sea.

基于复合喷气压电驱动器的柔性机械臂振动控制

空间机器人和大型柔性空间结构在航天器调姿、变轨、外部扰动的情况下将引起振动问题,其低频大幅值振动将持续很长时间,这将影响航天器系统的稳定性和控制精度。为了快速抑制低频大幅值振动及残余振动,提出采用复合可控反作用力幅值的喷气式驱动和压电陶瓷驱动方案进行振动控制。进行基于复合控制的柔性臂系统动力学建模并给出控制算法。设计并建立柔性机械臂试验平台,构建气动驱动控制回路及压电驱动控制回路。进行基于压电陶瓷驱动器、喷气式驱动器及复合喷气和压电驱动器的柔性臂大幅值低频模态振动控制的几种方法试验比较研究。试验结果表明,采用的控制方案和方法既可以快速地抑制柔性机械臂统的低频大幅值振动,又明显地同时抑制高频和低频小幅值残余振动。

使用补偿策略的机器人遥操作系统的控制研究

利用混杂动态系统的思想通过同时采用事件和时间驱动的执行器方案来弥补机器人遥操作系统中的不确定时延现象。即作为控制节点的操作者的控制决策发出时间是事件驱动的(满足一定条件下),执行器节点的接收也是事件驱动的,但是执行则是时间驱动的。通过这样的方法确保网络遥操作系统在每一采样周期内都能得到新的控制信号,从而补偿网络延迟。

一种五自由度机电测控系统的设计与实现

文章提出了一种基于五自由度机电系统的测控系统设计方法,并从机械系统构成、测控系统结构及软硬件设计方面论述了系统实现技术。针对系统特定的功能要求,文章详细介绍了位姿组合测量和各位姿自由度控制的测控方法,并应用模块化设计和数据流分析方法进行软硬件设计。通过实验进行系统特性分析,得到运行参数指标。实验证明这种设计方法和实现技术合理可行。

智能人工腿步速测量数字电路的设计与分析

智能人工腿是一个精密的机电一体化装置，其关键部件之一是步速测量电路。作者提出一种新的步速测量方法，即测量人工腿在摆动相的持续时间，用该时间的长短来间接反映步速的快慢，设计电路时，采用自顶向下（Top-Down）的设计方法，其核心内容是将测量系统按不同功能分割成几个模块，然后分别设计每一个模块电路，最后，用1片ispLSI1016高密度可编程芯片并采用ISP（In System Program）编程方法调离同步速测量电路。ISP编程方法的优点是可以现场修改，调速测量系统电路，并且不需要仿真器装置，实验结果表明：设计的这种步速测量电路结构合理，可有效地实现对智能人工腿步速的测量。

载人潜器半物理虚拟仿真系统及其性能分析

为了缩短深海载人潜器控制系统的开发周期,测试系统性能,根据载人潜器的自身特点,构建和实现了载人潜器所有传感器、执行器设备模拟,以及潜器在海底实景的运动状态的半物理虚拟仿真系统。首先,以仿真系统的硬件架构和数据流程为基础,重点介绍了潜器设备模拟的软件体系结构;其次,在仿真平台上测试了各种网络数据的传输延迟,分析了其整体性能;最后,得出了潜器控制器设计的时间约束。现阶段整个系统已经开发成功,并投入运行到潜器控制系统的安装调试中。

机器人化三腿磨削机床的研制

以钢坯修磨为实用目的研制的一台机器人化三腿机床，具有刚度大、负载能力强、机构简单、工作空间大、无运动耦合及奇异位形等优点，首次解决了钢坯局部修磨自动化问题，配以其它加工执行器还可实现多种工艺要求。建立了该机床的运动学逆、正解方程，对其工作空间和受力分析进行了介绍，并介绍了局部修磨自动化控制系统

基于加速度传感器的机器人最优学习控制

为工业机器人提出了一种最优学习控制法。这种控制法用加速度误差校正驱动器运动。并提出了一种基于几何级数的极限条件估计学习控制过程收敛条件的理论方法。所提出学习控制法的有效性通过PUMA562机器人的计算机仿真结果得到了证实。

Paradigms for Structure in an Amorphous Computer

Recent developments in microfabrication and nanotechnology will enable the inexpensive manufacturing of massive numbers of tiny computing elements with sensors and actuators. New programming paradigms are required for obtaining organized and coherent behavior from the cooperation of large numbers of unreliable processing elements that are interconnected in unknown, irregular, and possibly time-varying ways. Amorphous computing is the study of developing and programming such ultrascale computing environments. This paper presents an approach to programming an amorphous computer by spontaneously organizing an unstructured collection of processing elements into cooperative groups and hierarchies. This paper introduces a structure called an AC Hierarchy, which logically organizes processors into groups at different levels of granularity. The AC hierarchy simplifies programming of an amorphous computer through new language abstractions, facilitates the design of efficient and robust algorithms, and simplifies the analysis of their performance. Several example applications are presented that greatly benefit from the AC hierarchy. This paper introduces three algorithms for constructing multiple levels of the hierarchy from an unstructured collection of processors.

An Algorithm for Group Formation and Maximal Independent Set in an Amorphous Computer

Amorphous computing is the study of programming ultra-scale computing environments of smart sensors and actuators cite{white-paper}. The individual elements are identical, asynchronous, randomly placed, embedded and communicate locally via wireless broadcast. Aggregating the processors into groups is a useful paradigm for programming an amorphous computer because groups can be used for specialization, increased robustness, and efficient resource allocation. This paper presents a new algorithm, called the clubs algorithm, for efficiently aggregating processors into groups in an amorphous computer, in time proportional to the local density of processors. The clubs algorithm is well-suited to the unique characteristics of an amorphous computer. In addition, the algorithm derives two properties from the physical embedding of the amorphous computer: an upper bound on the number of groups formed and a constant upper bound on the density of groups. The clubs algorithm can also be extended to find the maximal independent set (MIS) and $Delta + 1$ vertex coloring in an amorphous computer in $O(log N)$ rounds, where $N$ is the total number of elements and $Delta$ is the maximum degree.

Towards Intelligent Structures: Active Control of Buckling

The buckling of compressively-loaded members is one of the most important factors limiting the overall strength and stability of a structure. I have developed novel techniques for using active control to wiggle a structural element in such a way that buckling is prevented. I present the results of analysis, simulation, and experimentation to show that buckling can be prevented through computer-controlled adjustment of dynamical behavior.sI have constructed a small-scale railroad-style truss bridge that contains compressive members that actively resist buckling through the use of piezo-electric actuators. I have also constructed a prototype actively controlled column in which the control forces are applied by tendons, as well as a composite steel column that incorporates piezo-ceramic actuators that are used to counteract buckling. Active control of buckling allows this composite column to support 5.6 times more load than would otherwise be possible.sThese techniques promise to lead to intelligent physical structures that are both stronger and lighter than would otherwise be possible.

Induced pluripotent stem cell-derived cardiac progenitors differentiate to cardiomyocytes and form biosynthetic tissues.

The mammalian heart has little capacity to regenerate, and following injury the myocardium is replaced by non-contractile scar tissue. Consequently, increased wall stress and workload on the remaining myocardium leads to chamber dilation, dysfunction, and heart failure. Cell-based therapy with an autologous, epigenetically reprogrammed, and cardiac-committed progenitor cell source could potentially reverse this process by replacing the damaged myocardium with functional tissue. However, it is unclear whether cardiac progenitor cell-derived cardiomyocytes are capable of attaining levels of structural and functional maturity comparable to that of terminally-fated cardiomyocytes. Here, we first describe the derivation of mouse induced pluripotent stem (iPS) cells, which once differentiated allow for the enrichment of Nkx2-5(+) cardiac progenitors, and the cardiomyocyte-specific expression of the red fluorescent protein. We show that the cardiac progenitors are multipotent and capable of differentiating into endothelial cells, smooth muscle cells and cardiomyocytes. Moreover, cardiac progenitor selection corresponds to cKit(+) cell enrichment, while cardiomyocyte cell-lineage commitment is concomitant with dual expression of either cKit/Flk1 or cKit/Sca-1. We proceed to show that the cardiac progenitor-derived cardiomyocytes are capable of forming electrically and mechanically coupled large-scale 2D cell cultures with mature electrophysiological properties. Finally, we examine the cell progenitors' ability to form electromechanically coherent macroscopic tissues, using a physiologically relevant 3D culture model and demonstrate that following long-term culture the cardiomyocytes align, and form robust electromechanical connections throughout the volume of the biosynthetic tissue construct. We conclude that the iPS cell-derived cardiac progenitors are a robust cell source for tissue engineering applications and a 3D culture platform for pharmacological screening and drug development studies.

Modelling and prototyping the conceptual design of 3D CMM micro-probe

This paper details the prototyping of a novel three axial micro probe based on utilisation of piezoelectric sensors and actuators for true three dimensional metrology and measurements at micro- and nanometre scale. Computational mechanics is used first to model and simulate the performance of the conceptual design of the micro-probe. Piezoelectric analysis is conducted to understand performance of three different materials - silicon, glassy carbon, and nickel - and the effect of load parameters (amplitude, frequency, phase angle) on the magnitude of vibrations. Simulations are also used to compare several design options for layout of the lead zirconium titanate (PZT) sensors and to identify the most feasible from fabrication point of view design. The material options for the realisation of the device have been also tested. Direct laser machining was selected as the primary means of production. It is found that a Yb MOPA based fiber laser was capable of providing the necessary precision on glassy carbon (GC), although machining trials on Si and Ni were less successful due to residual thermal effects.To provide the active and sensing elements on the flexures of the probe, PZT thick films are developed and deposited at low temperatures (Lt720 degC) allowing a high quality functional ceramic to be directly integrated with selected materials. Characterisation of the materials has shown that the film has a homogenous and small pore microstructure.

Entanglement distribution with global control in a star-shaped multi-splitter

Distributed quantum information processing (QIP) is a promising way to bypass problems due to unwanted interactions between elements. However, this strategy presupposes the engineering of protocols for remote processors. In many of them, pairwise entanglement is a key resource. We study a model which distributes entanglement among elements of a delocalized network without local control. The model is efficient both in finite- and infinite-dimensional Hilbert spaces. We suggest a setup of electromechanical systems to implement our proposal.