Crescimento inicial do eucalipto em função da aclimatação em viveiro

This study aimed to evaluate the acclimatization effects in the Eucalyptus grandis vs. Eucalyptus urophylla seedlings nursery in their initial growth in two soils types, clay and sandy. The seedlings were planted in Plantmax substrate and in rice hulls plus vermiculite, and managed, after 60 days of the mass propagation (DAE), during the rustication. There were five different frequencies of subsurface drip irrigation, restoring the soil field capacity condition: F1, F2, F3 and F4, which were irrigated once, twice, three and four times a day, respectively, and FD, kept in continue irrigation until planting at 90 DAE. In a randomized block design with four replications, plant height (HPA) were evaluated at 6 and 13 months after planting and the diameter at breast height (DAP) at 13 months after planting. Findings show that water management at hardening phase seedlings had no influence on growth in both soils.

On the dynamic behaviour of a nonlinear system weakly connected to a linear single degree-of-freedom system

This paper discusses the dynamic behaviour of a nonlinear two degree-of-freedom system consisting of a harmonically excited linear oscillator weakly connected to a nonlinear attachment that behaves as a hardening Duffing oscillator. A system which behaves in this way could be a shaker (linear system) driving a nonlinear isolator. The mass of the nonlinear system is taken to be much less than that in the linear system and thus the nonlinear system has little effect on the dynamics of the linear system. Of particular interest is the situation when the linear natural frequency of the nonlinear system is less than the natural frequency of the linear system such that the frequency response curve of the nonlinear system bends to higher frequencies and thus interacts with the resonance frequency of the linear system. It is shown that for some values of the system parameters a complicated frequency response curve for the nonlinear system can occur; closed detached curves can appear as a part of the overall amplitude-frequency response. The reason why these detached curves appear is presented and approximate analytical expressions for the jump-up and jump-down frequencies of the system under investigation are given.

Analysis on turning Ti-6Al-4V with different cooling methods

The aim of this paper is to optimize the machining of Ti-6Al-4V alloy, by studying the chip formation, roughness and tool wear for different cooling conditions. The results were compared between cooling methods, minimal quantity of fluid (MQF) and flooding, and also without fluid for the tool H13A. The turning of Ti-6Al-4V has shown good results on roughness (0, 8μm) and tool life, which was 11% lower with MQF than with the flooding method. The tool wear causes variation of the shear angle, which promotes strength hardening of the chip. As a result, the machined surface could be damaged. The use of the cutting fluid helps to save the cutting edge and could reduce the strength hardening. Nevertheless, it could also facilitate the formation of built-up edge. The nucleation of alpha lamellar colonies can occur due to a combination of deformation rates and temperature, mainly when the flooding is used, but it's not conclusive. The lamellar colonies were also found with the MQF in some regions, however, this structure did not show hardness variation compared to equiaxial. For all this reasons, the machining parameters might be carefully chosen.

An investigation of a two-stage nonlinear vibration isolation system

This paper investigates the most desirable configuration of a two-stage nonlinear vibration isolation system, in which the isolators contain hardening geometric stiffness nonlinearity and linear viscous damping. The force transmissibility of the system is used as the measure of the effectiveness of the isolation system. The hardening nonlinearity is achieved by placing horizontal springs onto the suspended and intermediate masses, which are supported by vertical springs. It is found that nonlinearity in the upper stage has very little effect and thus serves little purpose. The nonlinearity in the lower stage, however, has a profound effect, and can significantly improve the effectiveness of the isolation system. Further, it is found that it is desirable to have high damping in the upper stage and very low damping in the lower stage. © 2012 Elsevier Ltd.

Preparation of films from aluminum acetylacetonate by plasma sputtering

Aluminum acetylacetonate has been reported as a precursor for the deposition of alumina films using different approaches. In this work, alumina-containing films were prepared by plasma sputtering this compound, spread directly on the powered lowermost electrode of a reactor, while grounding the substrates mounted on the topmost electrode. Radiofrequency power (13.56 MHz) was used to excite the plasma from argon atmosphere at a working pressure of 11 Pa. The effect of the plasma excitation power on the properties of the resulting films was studied. Film thickness and hardness were measured by profilometry and nanoindentation, respectively. The molecular structure and chemical composition of the layers were analyzed by Fourier transform infrared spectroscopy and energy dispersive spectroscopy. Surface micrographs, obtained by scanning electron microscopy, allowed the determination of the sample morphology. Grazing incidence X-ray diffraction was employed to determine the structure of the films. Amorphous organic layers were deposited with thicknesses of up to 7 μm and hardness of around 1.0 GPa. The films were composed by aluminum, carbon, oxygen and hydrogen, their proportions being strongly dependent on the power used to excite the plasma. A uniform surface was obtained for low-power depositions, but particulates and cracks appeared in the high-power prepared materials. The presence of different proportions of aluminum oxide in the coatings is ascribed to the different activations promoted in the metalorganic molecule once in the plasma phase. Copyright © 2013 John Wiley & Sons, Ltd. Copyright © 2013 John Wiley & Sons, Ltd.

Avaliação de quatro métodos de restauração florestal de áreas úmidas degradadas no Município de Mineiros do Tietê - SP

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da dopagem com oxigênio nas propriedades anelásticas e biocompatibilidade de ligas Ti-5%pNb e Ti-10%pNb

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Global economic developments, 2000-2001

Includes bibliography

Análise não-linear física de vigas de concreto armado utilizando o elemento finito prismático regular linear associado ao de barra

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Uma análise da dinâmica do pêndulo eletromecânico utilizando a teoria de pertubações

Pós-graduação em Matemática - IBILCE

Fadiga no aço inox 15-5PH revestido por HVOF: aplicação em trem de pouso

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do efeito springback em aços avançados de alta resistência aplicados a indústria automobilística

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do envelhecimento após deformação em um aço complex phase

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito no processo ECAP (EQUAL CHANNEL ANGULAR) na microestrutura e nas propriedades mecânicas de uma liga comercial de alumínio AA3104

Pós-graduação em Engenharia Mecânica - FEG

Desenvolvimento de tubo ARBL contendo 1Cr 0,2Mo fabricado pelo processo ERW/HF destinado à indústria de petróleo e gás

Pós-graduação em Engenharia Mecânica - FEG