Model-based procedure for scale-up of wet, overflow ball mills - Part III: Validation and discussion

A new ball mill scale-up procedure is developed. This procedure has been validated using seven sets of Ml-scale ball mil data. The largest ball mills in these data have diameters (inside liners) of 6.58m. The procedure can predict the 80% passing size of the circuit product to within +/-6% of the measured value, with a precision of +/-11% (one standard deviation); the re-circulating load to within +/-33% of the mass-balanced value (this error margin is within the uncertainty associated with the determination of the re-circulating load); and the mill power to within +/-5% of the measured value. This procedure is applicable for the design of ball mills which are preceded by autogenous (AG) mills, semi-autogenous (SAG) mills, crushers and flotation circuits. The new procedure is more precise and more accurate than Bond's method for ball mill scale-up. This procedure contains no efficiency correction which relates to the mill diameter. This suggests that, within the range of mill diameter studied, milling efficiency does not vary with mill diameter. This is in contrast with Bond's equation-Bond claimed that milling efficiency increases with mill diameter. (C) 2001 Elsevier Science Ltd. All rights reserved.

Developments in the understanding of South African style SAG mills

The South African style SAG (RoM) mills operate in a window that is almost exclusive from the operation of the Australian and North American mills that have been used for the development of SAG mill models. Combining good quality, test data from the RoM mills is extending and improving these models, and assisting in a practical manner in improving our understanding of SAG/AG milling. Data from high mill loads, both in absolute filling and ball loading, have been used to extend and improve the JK SAG mill model. This improved understanding has been successfully applied to increasing the throughput of a mill by 8%. Data is presented on relationships between power and load for high mill loading. Slurry pooling is common in closed-circuit RoM mills, and the detrimental effect of this has been dramatically demonstrated at ALCOA with a mill throughput increase of over 20%. Techniques for calculating the effects of slurry pooling have been developed and a new pulp lifter system designed to give optimal slurry discharge. The influence of mill speed in shifting the product size distribution has also been measured. (C) 2001 Elsevier Science Ltd. All rights reserved.

Traffic and residue cover effects on infiltration

Wheel traffic can lead to compaction and degradation of soil physical properties. This study, as part of a study of controlled traffic farming, assessed the impact of compaction from wheel traffic on soil that had not been trafficked for 5 years. A tractor of 40 kN rear axle weight was used to apply traffic at varying wheelslip on a clay soil with varying residue cover to simulate effects of traffic typical of grain production operations in the northern Australian grain belt. A rainfall simulator was used to determine infiltration characteristics. Wheel traffic significantly reduced time to ponding, steady infiltration rate, and total infiltration compared with non-wheeled soil, with or without residue cover. Non-wheeled soil had 4-5 times greater steady infiltration rate than wheeled soil, irrespective of residue cover. Wheelslip greater than 10% further reduced steady infiltration rate and total infiltration compared with that measured for self-propulsion wheeling (3% wheelslip) under residue-protected conditions. Where there was no compaction from wheel traffic, residue cover had a greater effect on infiltration capacity, with steady infiltration rate increasing proportionally with residue cover (R-2 = 0.98). Residue cover, however, had much less effect on infiltration when wheeling was imposed. These results demonstrated that the infiltration rate for the non-wheeled soil under a controlled traffic zero-till system was similar to that of virgin soil. However, when the soil was wheeled by a medium tractor wheel, infiltration rate was reduced to that of long-term cropped soil. These results suggest that wheel traffic, rather than tillage and cropping, might be the major factor governing infiltration. The exclusion of wheel traffic under a controlled traffic farming system, combined with conservation tillage, provides a way to enhance the sustainability of cropping this soil for improved infiltration, increased plant-available water, and reduced runoff-driven soil erosion.

Tillage and traffic effects on runoff

Traffic and tillage effects on runoff and crop performance on a heavy clay soil were investigated over a period of 4 years. Tillage treatments and the cropping program were representative of broadacre grain production practice in northern Australia, and a split-plot design used to isolate traffic effects. Treatments subject to zero, minimum, and stubble mulch tillage each comprised pairs of 90-m 2 plots, from which runoff was recorded. A 3-m-wide controlled traffic system allowed one of each pair to be maintained as a non-wheeled plot, while the total surface area of the other received a single annual wheeling treatment from a working 100-kW tractor. Rainfall/runoff hydrographs demonstrate that wheeling produced a large and consistent increase in runoff, whereas tillage produced a smaller increase. Treatment effects were greater on dry soil, but were still maintained in large and intense rainfall events on wet soil. Mean annual runoff from wheeled plots was 63 mm (44%) greater than that from controlled traffic plots, whereas runoff from stubble mulch tillage plots was 38 mm (24%) greater than that from zero tillage plots. Traffic and tillage effects appeared to be cumulative, so the mean annual runoff from wheeled stubble mulch tilled plots, representing conventional cropping practice, was more than 100 mm greater than that from controlled traffic zero tilled plots, representing best practice. This increased infiltration was reflected in an increased yield of 16% compared with wheeled stubble mulch. Minimum tilled plots demonstrated a characteristic midway between that of zero and stubble mulch tillage. The results confirm that unnecessary energy dissipation in the soil during the traction process that normally accompanies tillage has a major negative effect on infiltration and crop productivity. Controlled traffic farming systems appear to be the only practicable solution to this problem.

Investigation of the effects of chrome ball charge on slurry rheology and milling performance

Ten surveys of the ball milling circuit at the Mt Isa Mines (MIM) Copper Concentrator were conducted aiming to identify any changes in slurry theology caused by the use of chrome balls charge, and the associated effect on grinding performance. Slurry theology was measured using an on-line viscometer. The data were mass balanced and analysed with statistical tools. Comparison of the rheogram demonstrated that slurry density and fines content affected slurry rheology significantly, while the effect of the chrome ball charge being negligible. Statistical analysis showed the effects of mill throughput and cyclone efficiency on the Grinding Index (a term describing the overall breakage). There was no difference in the Grinding Index between using the chrome ball charge and the ordinary steel ball charge. (C) 2002 Elsevier Science Ltd. All rights reserved.

'Vigilant Hospitality': The Online Imperative and Teaching Cultural Studies

Information technology (IT) sees information as a fluid, to be stored, regulated and exchanged. This is a profoundly economic model, whose dreams are those of the marketplace – and now, university managers. But no teacher, of course, holds that teaching can be reduced to the movement of information from one point to another. Teaching is never quite absorbed into the models of IT. Where they meet, we do not have the utopia of the virtual classroom, at last freed from the strictures of timetables and the face-to-face; we have, rather, the grinding of two radically irreducible models. This has nothing to do with Luddism; on the contrary, it is the value and necessity of IT for us at present, as teachers. At a time when the tertiary sector’s massive investment in IT is motivated in part by its own dream of the teacherless classroom, one of the pressing tasks for us may be simply to argue as rigorously as we can the structural necessity of our own position as teachers, without nostalgia or humanist sentimentality.

Practical and economic advantages of choice feeding systems for laying poultry

Poultry can be managed under different feeding systems, depending on the husbandry skills and the feed available. These systems include the following: (1) a complete dry feed offered as a mash ad libitum; (2) the same feed offered as pellets or crumbles ad libitum; (3) a complete feed with added whole grain; (4) a complete wet feed given once or twice a day; (5) a complete feed offered on a restricted basis; (6) choice feeding. Of all these, an interesting alternative to offering complete diets is choice feeding which can be applied on both a small or large commercial scale. Under choice feeding or free-choice feeding birds are usually offered a choice between three types of feedstuffs: (a) an energy source (e.g. maize, rice bran, sorghum or wheat); (b) a protein source (e.g. soyabean meal, meat meal, fish meal or coconut meal) plus vitamins and minerals and (c), in the case of laying hens, calcium in granular form (i.e. oyster-shell grit). This system differs from the modern commercial practice of offering a complete diet comprising energy and protein sources, ground and mixed together. Under the complete diet system, birds are mainly only able to exercise their appetite for energy. When the environmental temperature varies, the birds either over- or under-consume protein and calcium. The basic principle behind practising choice feeding with laying hens is that individual hens are able to select from the various feed ingredients on offer and compose their own diet, according to their actual needs and production capacity. A choice-feeding system is of particular importance to small poultry producers in developing countries, such as Indonesia, because it can substantially reduce the cost of feed. The system is flexible and can be constructed in such a way that the various needs of a flock of different breeds, including village chickens, under different climates can be met. The system also offers a more effective way to use home-produced grain, such as maize, and by-products, such as rice bran, in developing countries. Because oyster-shell grit is readily available in developing countries at lower cost than limestone, the use of cheaper oyster-shell grit can further benefit small-holders in these countries. These benefits apart, simpler equipment suffices when designing and building a feed mixer on the farm, and transport costs are lower. If whole (unground) grain is used, the intake of which is accompanied by increased efficiency of feed utilisation, the costs of grinding, mixing and many of the handling procedures associated with mash and pellet preparation are eliminated. The choice feedstuffs can all be offered in the current feed distribution systems, either by mixing the ingredients first or by using a bulk bin divided into three compartments.

Discrete element modelling of the influence of lifters on power draw of tumbling mills

Crushing and grinding are the most energy intensive part of the mineral recovery process. A major part of rock size reduction occurs in tumbling mills. Empirical models for the power draw of tumbling mills do not consider the effect of lifters. Discrete element modelling was used to investigate the effect of lifter condition on the power draw of tumbling mill. Results obtained with PFC3D code show that lifter condition will have a significant influence on the power draw and on the mode of energy consumption in the mill. Relatively high lifters will consume less power than low lifters, under otherwise identical conditions. The fraction of the power that will be consumed as friction will increase as the height of the lifters decreases. This will result in less power being used for high intensity comminution caused by the impacts. The fraction of the power that will be used to overcome frictional resistance is determined by the material's coefficient of friction. Based on the modelled results, it appears that the effective coefficient of friction for in situ mill is close to 0.1. (C) 2003 Elsevier Science Ltd. All rights reserved.

The JK three-product cyclone - performance and potential applications

In spite of their wide application in comminution circuits, hydrocyclones have at least one significant disadvantage in that their operation inherently tends to return the fine denser liberated minerals to the grinding mill. This results in unnecessary overgrinding which adds to the milling cost and can adversely affect the efficiency of downstream processes. In an attempt to solve this problem, a three-product cyclone has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to generate a second overflow in which the fine dense liberated minerals can be selectively concentrated for further treatment. In this paper, the design and operation of the three-product cyclone are described. The influence of the length of the second vortex finder on the performance of a 150-mm unit treating a mixture of magnetite and silica is investigated. Conventional cyclone tests were also conducted under similar conditions. Using the operational performance data of the three-product and conventional cyclones, it is shown that by optimising the length of the second vortex finder, the amount of fine dense mineral particles that reports to the three-product cyclone underflow can be reduced. In addition, the three-product cyclone can be used to generate middlings stream that may be more suitable for flash flotation than the conventional cyclone underflow, or alternatively, could be classified with a microscreen to separate the valuables from the gangue. At the same time, a fines stream having similar properties to those of the conventional overflow can be obtained. Hence, if the middlings stream was used as feed for flash flotation or microscreening, the fines stream could be used in lieu of the conventional overflow without compromising the feed requirements for the conventional flotation circuit. Some of the other potential applications of the new cyclone are described. (C) 2003 Elsevier Science B.V. All rights reserved.

Slurry flow in mills: grate-pulp lifter discharge systems (Part 2)

Pulp lifters, also known, as pan lifters are an integral part of the majority of autogenous (AG), semi-autogenous (SAG) and grate discharge ball mills. The performance of the pulp lifters in conjunction with grate design determines the ultimate flow capacity of these mills. Although the function of the pulp lifters is simply to transport the slurry passed through the discharge grate into the discharge trunnion, their performance depends on their design as well as that of the grate and operating conditions such as mill speed and charge level. However, little or no work has been reported on the performance of grate-pulp lifter assemblies and in particular the influence of pulp lifter design on slurry transport. Ideally, the discharge rate through a grate-pulp lifter assembly should be equal to the discharge rate through at a given mill hold-up. However, the results obtained have shown that conventional pulp lifter designs cause considerable restrictions to flow resulting in reduced flow capacity. In this second of a two-part series of papers the performance of conventional pulp lifters (radial and spiral designs) is described and is based on extensive test work carried out in a I m diameter pilot SAG mill. (C) 2003 Elsevier Science Ltd. All rights reserved.

Slurry flow in mills: grate-only discharge mechanism (Part-1)

Discharge grates play an important role in determining the performance of autogenous, semi-autogenous and grate discharge ball mills. The flow capacity (grinding capacity) of these mills is strongly influenced by the discharge grate design-open area and position of apertures, as well as the performance of the pulp lifters. As mill sizes have progressively increased and closed-circuiting has become more popular the importance of grate and pulp lifter design has grown. Unfortunately very few studies have concentrated on this aspect of mill performance. To remedy this a series of laboratory and pilot-scale tests were undertaken to study both the performance of grates on their own and in conjunction with pulp lifters. In this first paper of a two-part series the results from the grate-only experiments are presented and discussed, whilst the performance of the grate-pulp-lifter system is covered in the second paper. The results from the grate-only experiments have shown that the build-up of slurry (hold-up) inside the mill starts from the shoulder of the charge, while the toe position of the slurry progressively moves towards the toe of the charge with increasing flowrate. Besides grate design (open area and position of apertures), charge volume and mill speed were also found to have a strong influence on mill hold-up and interact with grate design variables. (C) 2003 Elsevier Science Ltd. All rights reserved.

Identificação Química em Nível Molecular de Amostras de Maconha por ESI-FT-ICR MS

mais consumida no país, e proscrita pela Lei n° 11.343 de 23 de agosto de 2006 (chamada de “nova lei de droga”), onde todos os isômeros, sais, éteres e ésteres do ∆9-Tetrahidrocannabinol (THC), princípio ativo, foram proscritos. O método utilizado pela Polícia Civil do Estado do Espírito Santo para a identificação de cannabinóides é o teste colorimétrico, por meio de solução básica de Salt Fast Blue B, o qual apresenta resultados falsos negativos e falsos positivos. A técnica de espectrometria de massas de altíssima resolução e exatidão de massas (ESI(-)FTICR MS), permite detectar os principais cannabinóides na forma de molécula desprotonada, íon [M-H]-. Alguns íons que podem ser identificados são: [CBN - H]- de m/z 309 (CBN = cannabinol); [THC - H]- de m/z 313 (THC = tetrahidrocannabinol) e [CBD - H]- de m/z 313; [CBC - H]- de m/z 327 (CBC = cannabicromeno); [CBEA - H]- de m/z 345 (CBEA = ácido cannabielsóico); [CBNA - H]- de m/z 353 (CBNA = ácido cannabinólico); [THCA - H]- de m/z 357 (THCA = ácido tetrahidrocannabinólico); [8α, 11-Bis-hydroxy-∆9-THC-A - H]- de m/z 389); [∆9-THCA +C2H2O - H]- de m/z 357; e dímeros com m/z de 637, 653, 673, 681, 685 e 717. Foram encontrados adulterantes identificados como [M + N + H]+ : 491; [2M + N + H]+ : 819 e [3M + N + H]+ : 1147, onde M = OTHC (328Da C21H28O3) e N = Nicotina (162Da C10H14N2), além de lidocaína e cocaína. Ainda foram identificados alguns noncannabinóides como Cannflavino A e B e ácidos graxos como palmítico, oleico, linolênico e gama-linolênico nos extratos de sementes de Cannabis. Este estudo tem o objetivo de identificar o perfil químico de amostras de maconha, apreendidas pela Polícia Civil do Estado do Espírito Santo, por ESI(±)-FT-ICR MS.

Inv(f)erno da Universidade de Verão

Despesa em educação é investimento constitucional: art.s 75º e 76º da Constituição. Como referiu o director da Revista Ensino Superior, nº 53, pp. 4-5, ex-presidente do Sindicato Nacional do Ensino Superior, Professor da Faculdade de Economia da Universidade de Coimbra, Doutor Paulo Peixoto, o ensino superior tornou-se em grande parte uma “máquina de triturar intelectuais”. A tentativa de impor uma mentalidade única pode provocar a destruição da génese da própria universalidade. § Spending on education is constitutional investment: Articles 75 and 76 of the Constitution. As the director of the Journal of Higher Education, # 53, pp. 4-5, former president of the National Union of Higher Education, Professor of Economics, University of Coimbra, Dr. Paulo Peixoto, higher education has become largely an 'intellectual grinding machine. "The attempt to impose a single mindset may cause the destruction of the very universality genesis.

O aluno com deficiência motora e a acessibilidade arquitectónica no Ensino Básico : um estudo de caso : o concelho de Guimarães

RESUMO:Para que o sucesso educativo se verifique, a escola tem de ajustar a sua prática educativa a todos os alunos, incluindo os que apresentam necessidades educativas especiais (NEE). Portugal dispõe de legislação que assegura o direito à educação e à igualdade de oportunidades, consignados na Constituição da República Portuguesa (artigos 71º, 73º e 74º), em consonância com a Declaração Universal dos Direitos do Homem e na Lei de Bases do Sistema Educativo (artigos 2º, 7º, 17º e 18º). O nosso país subscreveu também a Declaração de Salamanca, a qual reuniu, em 1994, o consenso de noventa e dois governos e de vinte e cinco organizações internacionais, reafirmando o direito à educação para todos. A construção da escola inclusiva passa pela responsabilização da escola por todos os alunos, na perspectiva de educação para todos, exigindo a sua concretização novas estratégias e resposta a novos desafios. Há que alterar práticas para atender à diversidade. Assim, as escolas precisam de estar arquitectonicamente adaptadas às necessidades dos alunos que utilizam a cadeira de rodas como forma de mobilidade, respeitando o direito à diferença e possibilitando, em igualdade de oportunidades, o sucesso escolar e educativo. Levar à prática as medidas previstas na lei portuguesa e implementar, em cada escola, a inclusão do aluno com mobilidade condicionada, implica equipar as escolas com adaptações, meios e recursos educativos facilitadores do seu processo ensino/aprendizagem. A constatação do que efectivamente acontece no terreno educativo no que concerne aos alunos com deficiência motora que usam a cadeira de rodas para se movimentarem assume toda a centralidade da nossa investigação, que tem o cariz de um estudo de caso. Incide sobre a compreensão mais aprofundada de como se processa o acesso arquitectónico nas escolas do Ensino Básico da Zona Norte e mais concretamente do Concelho de Guimarães. Recolhemos dados através de questionários dirigidos aos professores de apoio educativo e coordenadores de escola; ouvimos os alunos com deficiência motora pronunciar-se sobre as dificuldades que sentiam; observámos o seu quotidiano escolar e, finalmente, escutámos as entidades locais, através de uma entrevista realizada à Vereadora da Cultura do Concelho de Guimarães. Os resultados obtidos serão, como foi acordado, divulgados aos intervenientes com responsabilidades directas no campo da educação que se prontificaram a partilhar connosco a sua informação e saber, no sentido de os sensibilizar para a necessidade de rever o aspecto das acessibilidades arquitectónicas nas instituições educativas que servem o seu concelho, pois, como verificámos, muito há ainda a fazer para que o Ensino Básico, universal e obrigatório, se traduza numa igualdade de oportunidades de acesso e sucesso educativo para os alunos que utilizam a cadeira de rodas para se movimentarem no espaço escolar. ABSTRACT: For the educational success of a school it has to adjust its educational practice so that it includes those with special needs. According to the Portuguese law, disabled people have the right to education and equal opportunities, well expressed in the Constitution of the Portuguese Republic (articles 71st, 73rd, and 74th), in consonance with the Universal Declaration of Human Rights, and in the main law the educational system (articles 2nd, 7th, 17th and 18th). Our country has also subscribed the Declaration of Salamanca, which was written in 1994 with the agreement of Representatives from ninety-two governments and twenty-five International Organizations, where was reaffirmed the right of education for all. It is necessary that school increases its responsibility in what concerns the education of all its students. Educating all and every student demands new strategies to face new challenges and so some practices have to be changed to respond to diversity. Schools must be architecturally adapted to give the disabled students, who use a wheel chair, equal opportunities to achieve educational success. Taking the measures foreseen in Portuguese law into practice, and implementing in each school the inclusion of students with conditioned mobility, involves equipping schools with adaptations, equipment and educational resources that facilitate the teaching / learning process. The observation of what actually happens on educative ground, regarding to pupils with motor disabilities who use a wheelchair to move, assumes the centrality of our research, which is a case study. It focuses on the deeper understanding of the way the architectonic access in primary schools of the North, and more specifically the Municipality of Guimarães, is processed. We collected data through questionnaires addressed to educational support teachers and school coordinators; heard students with motor disabilities to comment on the difficulties they felt; observed their daily school life, and finally heard the local authorities, through an interview the Councillor of Culture of the Municipality of Guimarães. As agreed, the results will be communicated to intervenients with direct responsibilities in the field of education who were willing to share with us their information and knowledge in order to raise awareness of the need of looking over the aspect of architectural accessibility in educational institutions that serve their county, because, as noted, much remains to be done so that the basic education, universal and compulsory, will result in equality of educational opportunities in access and success for students who use a wheelchair to move in school space.

Web 2.0 and its impact on knowledge and business organizations

Today, information overload and the lack of systems that enable locating employees with the right knowledge or skills are common challenges that large organisations face. This makes knowledge workers to re-invent the wheel and have problems to retrieve information from both internal and external resources. In addition, information is dynamically changing and ownership of data is moving from corporations to the individuals. However, there is a set of web based tools that may cause a major progress in the way people collaborate and share their knowledge. This article aims to analyse the impact of ‘Web 2.0’ on organisational knowledge strategies. A comprehensive literature review was done to present the academic background followed by a review of current ‘Web 2.0’ technologies and assessment of their strengths and weaknesses. As the framework of this study is oriented to business applications, the characteristics of the involved segments and tools were reviewed from an organisational point of view. Moreover, the ‘Enterprise 2.0’ paradigm does not only imply tools but also changes the way people collaborate, the way the work is done (processes) and finally impacts on other technologies. Finally, gaps in the literature in this area are outlined.