An automated microreactor for semi-continuous biosensor measurements.

Living bacteria or yeast cells are frequently used as bioreporters for the detection of specific chemical analytes or conditions of sample toxicity. In particular, bacteria or yeast equipped with synthetic gene circuitry that allows the production of a reliable non-cognate signal (e.g., fluorescent protein or bioluminescence) in response to a defined target make robust and flexible analytical platforms. We report here how bacterial cells expressing a fluorescence reporter ("bactosensors"), which are mostly used for batch sample analysis, can be deployed for automated semi-continuous target analysis in a single concise biochip. Escherichia coli-based bactosensor cells were continuously grown in a 13 or 50 nanoliter-volume reactor on a two-layered polydimethylsiloxane-on-glass microfluidic chip. Physiologically active cells were directed from the nl-reactor to a dedicated sample exposure area, where they were concentrated and reacted in 40 minutes with the target chemical by localized emission of the fluorescent reporter signal. We demonstrate the functioning of the bactosensor-chip by the automated detection of 50 μgarsenite-As l(-1) in water on consecutive days and after a one-week constant operation. Best induction of the bactosensors of 6-9-fold to 50 μg l(-1) was found at an apparent dilution rate of 0.12 h(-1) in the 50 nl microreactor. The bactosensor chip principle could be widely applicable to construct automated monitoring devices for a variety of targets in different environments.

Immediate ecotoxicological effects of short-lived oil spills on marine biota.

Marine environments are frequently exposed to oil spills as a result of transportation, oil drilling or fuel usage. Whereas large oil spills and their effects have been widely documented, more common and recurrent small spills typically escape attention. To fill this important gap in the assessment of oil-spill effects, we performed two independent supervised full sea releases of 5 m(3) of crude oil, complemented by on-board mesocosm studies and sampling of accidentally encountered slicks. Using rapid on-board biological assays, we detect high bioavailability and toxicity of dissolved and dispersed oil within 24 h after the spills, occurring fairly deep (8 m) below the slicks. Selective decline of marine plankton is observed, equally relevant for early stages of larger spills. Our results demonstrate that, contrary to common thinking, even small spills have immediate adverse biological effects and their recurrent nature is likely to affect marine ecosystem functioning.

Information integration and its impacts on logistics performance - Using information technology and systems to facilitate information integration

Fast changing environment sets pressure on firms to share large amount of information with their customers and suppliers. The terms information integration and information sharing are essential for facilitating a smooth flow of information throughout the supply chain, and the terms are used interchangeably in research literature. By integrating and sharing information, firms want to improve their logistics performance. Firms share information with their suppliers and customers by using traditional communication methods (telephone, fax, Email, written and face-to-face contacts) and by using advanced or modern communication methods such as electronic data interchange (EDI), enterprise resource planning (ERP), web-based procurement systems, electronic trading systems and web portals. Adopting new ways of using IT is one important resource for staying competitive on the rapidly changing market (Saeed et al. 2005, 387), and an information system that provides people the information they need for performing their work, will support company performance (Boddy et al. 2005, 26). The purpose of this research has been to test and understand the relationship between information integration with key suppliers and/or customers and a firm’s logistics performance, especially when information technology (IT) and information systems (IS) are used for integrating information. Quantitative and qualitative research methods have been used to perform the research. Special attention has been paid to the scope, level and direction of information integration (Van Donk & van der Vaart 2005a). In addition, the four elements of integration (Jahre & Fabbe-Costes 2008) are closely tied to the frame of reference. The elements are integration of flows, integration of processes and activities, integration of information technologies and systems and integration of actors. The study found that information integration has a low positive relationship to operational performance and a medium positive relationship to strategic performance. The potential performance improvements found in this study vary from efficiency, delivery and quality improvements (operational) to profit, profitability or customer satisfaction improvements (strategic). The results indicate that although information integration has an impact on a firm’s logistics performance, all performance improvements have not been achieved. This study also found that the use of IT and IS have a mediocre positive relationship to information integration. Almost all case companies agreed on that the use of IT and IS could facilitate information integration and improve their logistics performance. The case companies felt that an implementation of a web portal or a data bank would benefit them - enhance their performance and increase information integration.

De Bermudes of Summer Eylanden tot de reystogten afgepeyld door de Engelzen derwaards gedaan

Julkaisussa: De wijd-beroemde voyagien na Oost en West-Indien. Vol I

Teollinen öljyn erotus koalesenssisuodatuksella väliaineessa

Koalesenssi on ilmiö, jossa dispergoidun faasin pisarat pyrkivät muodostamaan suurempia pisaroita kunnes erotettava faasi muodostuu. Koalesenssi tapahtuu kolmessa päävaiheessa, jotka ovat lähestyminen, kiinnittyminen ja irrotus. Lähestymiseen vaikuttavat mekanismit ovat muuan muassa sieppaus, diffuusio, törmäysvaikutus, sedimentaatio, sähköiset repul-siovoimat ja van der Waalsin voimat. Kiinnittymisvaiheessa dispergoidun faasin pisarat syrjäyttävät väliaineen nestekalvon samalla kostuttaen väliaineen pinnan. Irrotusvaiheessa pisaran hydrodynaaminen voima voittaa pisaran ja väliaineen välisen adheesiovoiman. Koalesenssin tehokkuuteen vaikuttavat useat eri parametrit kuten virtausnopeus, pedin ominaisuudet, väliaineen ominaisuudet sekä emulsion ominaisuudet. Nämä kaikki asiat tulee ottaa huomioon koalesenssisuodatuksen suunnittelussa. Koalesenssisuodatus lukeutuu syväsuodatusmenetelmiin, jotka on ollut käytössä jo yli 100 vuotta. Koalesenssisuodatusmenetelmä on tehokas menetelmä pienten pisaroiden erottami-seen. Menetelmää käytetään esimerkiksi öljyisten jätevesien puhdistuksessa. Teollisen öljyn syväsuodatuksen etuihin kuuluu muun muassa sen kompakti koko, alhaisemmat käyt-tökustannukset, korkea erotusaste, kyky erotella pienetkin pisarat sekä helppo operointi, automatisointi ja huolto. Suurin haittapuoli on kuitenkin väliaineen tukkeutuminen, joten prosessi vaatii puhdistuksen tai väliaineen uusimisen. Tämän kandidaatintyön tarkoituksena oli koota kirjallisuustyö öljyn koalesenssisuodatuk-sesta. Työssä kartoitettiin koalesenssisuodatuksen lähtökohdat, teoria, tärkeimmät teolli-suuden sovellukset sekä väliaineet.

Inclusive education: exploring teachers' perspectives /

This study explores 5 teachers' perspectives on inclusive education. The literature reviewed gives a historical background of special education as well as discusses a number of current methods and techniques that have been implemented as a means to include exceptional students in regular classroom settings. This is a qualitative study that collected and interpreted data in narrative form. Common themes emerged from the accounts that were shared by the participants. This study found that the understanding of mUltiple intelligences and differentiated instruction might assist a teacher to better meet the needs of exceptional students within inclusive classrooms. Based on this study, it is determined that a range of considerations needs to be weighed when choosing an educational placement for a student with an exceptionality. Each decision needs to be based on the individual student and the options open to himlher. When a decision about class placement is to be made, not only are the student's strengths and needs to be considered, but also the school and community, the teacher, and the parents' desire for their child must be taken into account. More work still needs to be done around inclusive education that is at the practical level, so that the needs of both the student and the teacher can be met. Inclusive education did not mean the same thing to each person. It was individualized, just as each student is an individual and what works best for himlher is individual. In learning about inclusive education, settings and strategies need to be considered to allow for each individual student to achieve hislher personal best.

Electrical properties of some single crystal dodecaborides /|nby Jyoti Burte. -- 260 St. Catharines [Ont. : s. n.],

PreVi011.3 ':i or~ : indicat e('. tk~t ho t~)rE's sed ~-Al B 12 1i~2, ~' a semiconductor. r:Toreove r , the s i mpl.(~ electronic t heory also indi cates that ~ -AIB1 2 should be a semico nductor, since thf're is one nonbonding e 'Le ctrofl per AlB12- uni t. JPor these reasons, we decided to measure t he electrical n ropert i ~ s of ~ -AlB1 2 single crystal s . Singl e crystal s of¥- AIB 12 ab ou t 1 x 1 r1n1 . size were grown from a copper mel t at 12500 C. The melt technique coupled. 1,vi th slow cooling vilas used because of i ts advantages such as : siTYInle set- up of the expe rimon t ; only e ;l.sil y available c hemi cals are required and it i s a c omparatively strair::bt forvvard y,le t hod still yielding crystal s big enouGh for OtU' purpose . Copper rms used as a solvent , i nst8ad of previOl.wly used aluminum , because it allows c.l.'ystal growth at hig he r t emneratures. HovlGver, the cry s tals of ] -AlB12 shm'red very hi gh res i s t ance a t r oom temperature . From our neasureJ'lents we conclude that the r esistivity of j3- Al B12 is, at least, given as ~ = 4. x 107 oblD .em •• Those results are inc ons i s t ent wi 'uh the ones .. reported by IIiss Khin fo r bot- pressed j3-AlB12 g i ven a s = 7600 ohm . em . or I e s s . ' Since tbe hot pressing was done at about 800 - ' 9000C i n ~ rap hi te moul ds 1,7i th 97% AlB12- p oVJder, vie thi nk there is pas s ib i 1 i ty th a.t lower borides or borot] carbide are , being formed, ':.Jhich are k11 own to be good semiconductors . v7e tried to ro-pe r-AlB12 by addi'J,'?: agents s uch as l:Ig , IG.-InO 4. ' HgS04 , KI12PO 4·' etc. to t he melt .. However , all these re age 11 t eel either reduced the yield and size of t lJe crystals or r;ave crystals of high r esis'can ce again. We think tba t molten copper keeps t he i mpurities off . There is also a pos s i bil i ty t hc:!,t these doping agents get oxidi~::;ed at '1 250°C • Hence, we co ~ clud e that J -AIB12 has v~ ry high r es i stance at r oom temperature . This was a l s o C011 - fi rmed by checki ng the siYlgle and. polycrystals of .~-AIB12 from Norton Co., Ontario and Cooper Nletallurgical Association. Boron carbide has been reported to be a semiconductor with ~ - 0.3 to 0.8 ohm . cm. for hotpres sed s araples. Boron carbide b e inq: struct urally related to ¥-AIB12 , we de cided to study the electrical prone rties of it~ Single crystals. These crystals were cut from a Single melt grovvn crystal a t Norton Co., Ontario. The resistivity of th," se crystal s was measured by the Van der Pam-v' s ~ nethod, which \vas very c onvenient fo r our crystal sha-pp.s. Some of the crystals showed resistivity ~ == 0.50 ob,Tn.cr] . i n agreement with the previously reported results . However , a few crystals showed lower resistivity e.g . 0 .13 and 0.20 ohm.cra • • The Hall mobility could .not be measured and th8reiore i s lower than 0 .16 em 2 v - 1 sec -1 • This is in agreement \vith t he re1)orted Hall mobility for pyrolytic boron . _ 2 -1 -1 carbide as 0.13 cm v sec • We also studied the orientation of the boron carbide crystals by the Jjaue-method. The inclination of c-axis with res pect to x-ray be81Il was det ermined . This was found to be 100 t o 20° f or normal resistivity sarnples (0.5 ohm . cm.) and 27 - 30° for t he lower r esistivity samples (0.1 ~5 to 0.20 ohm.cm .). This indica tes the possibility that th.e r es if.1tivity of B13C3 i s orientation dependent.

Far infrared spectroscopy of heavy fermion superconductor CeCoIn5

The optical response to far infrared radiation has been measured on a mosaic of heavy fermion CeColnssingle crystals. The superconducting transition temperature of the crystals has been determined by van der Pauw resistivity and ac-susceptibility measurements as Tc = 2.3 K. The optical measurements were taken above and below the transition temperature using a 3He cryostat and step and integrate Martin-Puplett type polarizing interferometer. The absolute reflectance of the heavy fermion CeColns in the superconducting state in range (0, 100)cm-1 was calculated from the measured thermal reflectance, using the normal state data of Singley et al and a low frequency extrapolation for a metallic material in the Hagen-Rubens regime. By means of Kramers-Kronig analysis the absolute reflectance was used to calculate the optical conductivity of the sample. The real part of the calculated complex conductivity 0-(w) ofCeColns indicates a possible opening of an energy gap close to 50 em-I.

Some electrical properties of semi-conductor crystals / |nPhyu Phyu Khin. -- 260 St. Catharines, Ont. : [s. n.],

SiC and AtB 12 have been prepared and their resistivities and Hall voltages measured. The resistivities and Hall voltages were measured by the Van der Pauw's method, using spring loaded tungsten contacts. In this method, the major requirement is to have samples of plane parallel surfaces of arbitrary shape with four small contacts at the circumference. Similar measurements were made with a number of SiC crystals obtained from the Norton Research Corporation (Canada)-Ltd., Carolina Aluminum Co., Exolon Co. and Carborundum Co. It was found that resistivity, carrier concentration and mobility of ions depend on the type of impurity. AtB 12 was prepared from the melt containing At and B in the ratio of 4:1. They formed amber-colour pseudo tetragonal crystals. As the crystals obtained were small for electrical measurements, hot pressed lumps have been used to measure their resistivity.

The application of the structural correlation method to determine the reaction coordinate for a putative ring closure reaction

The cr ystal structure of the compound 2-benzoylethylidene-3-(2,4- dibromophenyl)-2,3-dihydro-5-phenyl-l,3,4-thiadiazole* C23H16Br2NZOS (BRMEO) has been determined by using three dimensiona l x-ray diffraction data. The crys tal form is monoclinic, space group P21/c, a = 17.492(4), o -.t' 0 R 0 b =: 16.979(1), c = 14.962(1) A, "X. =o= 90 ',= 106.46(1) , z = 8, graphite-monochromatized Mo~ rad iation, Jl= 0.710J3~, D = 1.62g/cc and o D = 1.65g/cc. The data were col lected on ~ Nonius CAD-4 c diffractometer. The following atoms were made anisotropic: Br, S, N, 0, C7, and C14-C16 for each i ndependent molecu le ; the rest were left isotropic. For 3112 independent refl ec tions with F > 6G\F), R == 0.057. The compound has two independent molecules within the asymmetric unit. Two different conformers were observed which pack well together. /l The S---O interaction distances of 2.493(6) and 2 . 478(7) A were observed for molecules A and B respectively. These values are consistent with earlier findings for 2-benzoylmethylene-3-(2,4-dibromophenyl)- ~~ 2,3-dihydro-5-phenyl-l,3,4-thiadiazole C22H14Br2N20S (BRPHO) and 2-benzoylpropylidene-3-(2,4-dibromophenyl)-2,3-dihydroiii ,'r 5-phenyl-l,3,4-thiadiazole C24H18Br2N20S (BRPETO ) where S---O distances are l ess than the van der Waals (3.251\) but greater than those expected for () a single bond (1.50A). From the results and the literature it appears obvious that the energy/reaction coordinate pathway has a minimum between the end structures (the mono- and bicyclic compounds). * See reference (21) for nomenclature.

The crystal and molecular structure of thiamine hydroiodide /|nWilliam Edward Lee. -- 260 St. Catharines [Ont.] : Dept. of Chemistry, Brock University,

The x-ray crystal structure of thiamine hydroiodide,C1ZH18N40S12' has been determined. The unit cell parameters are a = 13.84 ± 0.03, o b = 7.44 ± 0.01, c = 20.24 ± 0.02 A, 8 = 120.52 ± 0.07°, space group P2/c, z = 4. A total of 1445 reflections having ,2 > 2o(F2), 26 < 40° were collected on a Picker four-circle diffractometer with MoKa radiation by the 26 scan technique. The structure was solved by the heavy atom method. The iodine and sulphur atoms were refined anisotropically; only the positional parameters were refined for the hydrogen atoms. Successive least squares cycles yielded an unweighted R factor of 0.054. The site of protonation of the pyrimidine ring is the nitrogen opposite the amino group. The overall structure conforms very closely to the structures of other related thiamine compounds. The bonding surrounding the iodine atoms is distorted tetrahedral. The iodine atoms make several contacts with surrounding atoms most of them at or near the van der Waal's distances A thiaminium tetrachlorocobaltate salt was produced whose molecular and crystal structure was j~dged to be isomorphous to thiaminium tetrachlorocadmate.

Far infrared spectroscopy of heavy fermion superconductor CeCoIn5 /

The optical response to far infrared radiation has been measured on a mosaic of heavy fermion CeCoIns single crystals. The superconducting transition temperature of the crystals has been determined by van der Pauw resistivity and ac-susceptibility measurements as Tc = 2.3 K. The optical measurements were taken above and below the transition temperature using a ^He cryostat and step and integrate Martin-Puplett type polarizing interferometer. The absolute reflectance of the heavy fermion CeCoIns in the superconducting state in range (0, 100)cm~^ was calculated from the measured thermal reflectance, using the normal state data of Singley et al and a low frequency extrapolation for a metallic material in the Hagen-Rubens regime. By means of Kramers-Kronig analysis the absolute reflectance was used to calculate the optical conductivity of the sample. The real part of the calculated complex conductivity a{u)) of CeCoIns indicates a possible opening of an energy gap close to 50 cm~^.

L’élaboration d’un programme d’Enseignement à distance par radio (EADR) pour l’amélioration des résultats d’examens officiels du baccalauréat 1ère partie en Haïti

Ce mémoire de maîtrise porte sur la contribution que pourrait apporter l’Enseignement à distance par radio (EADR) dans la réduction du taux d’échec aux examens du baccalauréat 1ère partie en Haïti. De manière spécifique, nous souhaitions élaborer un programme d’ « Enseignement à distance par radio » (EADR) afin d’aider l’ensemble des candidats bacheliers des classes de Rhéto à préparer les examens du bac 1ère partie. En Haïti, l’Enseignement à distance (EAD) est pratiquement absent. De nombreux pays ayant eu des situations similaires à Haïti ont mis en place des programmes de « Formations ouvertes et à distance » (FOAD) en complémentarité avec le mode d’enseignement classique ou en mode présentiel. La complexité de la situation exige d’envisager diverses pistes pour sortir le système éducatif haïtien de cette léthargie. Si l’on ne peut considérer l’EAD comme l’unique perspective, il est par contre pertinent et souhaitable de l’envisager comme une alternative non négligeable (Lubérisse, 2003). En nous appuyant sur les principales conditions d’efficacité des FOAD définies par Karsenti (2003), les principes théoriques de type R & D (Van der Maren, 2003?), le cadre théorique de la méthodologie de l’évaluation des besoins de Chagnon et Paquette (Institut universitaire des Centres Jeunesses de Montréal, 2005) et de Roegiers, Wouters & Gerard (1992), nous avons élaboré les grandes lignes générales de ce programme d’EADR et les avons soumises à douze (12) acteurs clés du système éducatif haïtien (4 élèves, 3 parents, 2 enseignants et 3 spécialistes de la radio ou de l’EADR). Cette ébauche de programme comportait principalement les objectifs du programme d’EADR, la méthode pédagogique, le contenu et les conditions de mise en œuvre. Des données recueillies par le biais d’entrevues individuelles il ressort que l’implantation d’un programme d’EADR peut être bénéfique au système éducatif haïtien, particulièrement sur les résultats d’examens officiels du baccalauréat 1ère partie. Les douze participants à notre recherche, croient que l’objectif poursuivi par le programme d’EADR est tout à fait réalisable et important pour le public cible. Tout en notant l’aspect positif du programme d’EADR proposé, les participants réclament certaines modifications quant à la méthode pédagogique, au contenu et aux conditions de mise en œuvre. Ainsi, les recommandations faites par les douze acteurs clés du système éducatif, jointes à notre recension nous ont permis d’élaborer un nouveau programme d’EADR revu et corrigé qui pourra servir de base à une évaluation plus large.

Mâle dans leur poids : une étude sur les variables explicatives de la préoccupation des hommes québécois avec surpoids à l'égard du poids

L’objectif de cette recherche qualitative était de porter un regard sur la problématique du poids chez l’homme à partir des déterminants de la santé masculine définis par Courtenay (2003). En donnant la parole à 17 hommes québécois en surpoids lors d’entrevues individuelles, différentes variables associées à leur préoccupation à l’égard du poids, sont examinées. Selon ces hommes, il existe un comportement alimentaire typiquement masculin autant dans le choix des aliments que dans la façon de manger. La présence féminine joue pour eux un rôle prépondérant dans ce domaine. La vision masculine de la santé suit souvent la fonctionnalité de leur corps tandis que leur description du surpoids semble davantage partir du « vécu » et être moins stricte que la définition purement médicale. Néanmoins, beaucoup d’hommes sentent la pression de l’image du corps idéal masculin et sont souvent insatisfaits de leur corps selon la masculinité valorisée et selon la stigmatisation subie. La préoccupation des hommes à l’égard de leur santé est très présente parmi les hommes de 30-45 ans et perdre du poids dans ce contexte devient alors légitime mais les raisons évoquées varient : la santé, l’apparence, le bien-être. L’expression des douleurs émotionnelles autour du poids est difficile pour les hommes et trop souvent la masculinité traditionnelle constitue une barrière de taille à la consultation pour ces problèmes. Pour le futur, il sera donc important pour les professionnels de la santé d’intégrer les différentes caractéristiques de cette masculinité traditionnelle dans leur approche et leur communication avec les hommes en surpoids.

Exploration d'une méthodologie du diagnostic des difficultés dans le cadre d'un cours de méthodologie de la recherche en éducation

Thèse diffusée initialement dans le cadre d'un projet pilote des Presses de l'Université de Montréal/Centre d'édition numérique UdeM (1997-2008) avec l'autorisation de l'auteur.